How to recover IDS using CD recovery. and/or password recovery

I'm getting the following error message:
"No Hard drives has been found. You probably need to manually choose device drivers for the installation to succeed. Would you like to select drivers now?"
IDS cd os 4.1(1)
Choosing yes doesn’t lead to selecting drivers and I'm not sure how to install them. Choosing no doesn't help either.
Also I'm trying to use this recovery CD on other unit that is password protected and I lost the password for it. i can't even boot from the CD. It boots immediately from the HD and it wont let me go for the CMOS setup to change boot order.
Oren

Okay...first things first. The IDS-4210 does have a power button. If the bezel is installed, there is a silver button on the front that controls power. If the bezel is removed, you will need to push on the plastic circuit cover where the power symbol is located. The symbol looks like a circle with a vertical line at the top. Press directly on that symbol. Typically the sensor will boot back up if you remove power the way you described if it was running at the time. This is because the power settings in CMOS are setup to return to the last state (running, off) after a power failure. It's possible that messing with the jumper on the board resets this setting causing it to lose state, and thereby requiring you to manually press the power button to get the system to come back up. This should get us back to the HDD issue....
When you had the cover off, did you happen to check the power and IDE cables to the HDD? If not, try removing and reseating the connectors as a first step. You may also try moving the drive to the other bay and connecting it there (to rule out cable issues). This config should work, but it hasn't been tested. If you are still having problems, it is probably a HDD failure, and I would recommend RMAing the system. If you really want to make sure this is the problem before going through the hassle of an RMA, you can test the drive in a separate system (or swap with your second 4210). Just don't install two drives in the same 4210 at the same time.
On the second system, you indicated that it was not booting to the CD, but would boot directly to the HDD. This may still be an issue with your CD copy, because not all IDS-4210s will behave the same way, even with the same CD. We have witnessed this in the lab ourselves. My only guess is that some of the CD-ROM drives are more sensitive than others. I would try to verify BIOS settings on this system before blaming the CD though, unless you have another CD to test with.
Regarding breaking into CMOS, can you describe what you are seeing when the system boots? Are you connected through the serial port or with a keyboard and monitor? If you are connected through the serial port, you may not see anything if console redirection is not enabled in the BIOS. You will have to connect a keyboard and monitor to fix this. If you are on a monitor, you should see one of two things...either a Cisco splash screen, or standard text POST messages with a prompt to hit to run SETUP. Hit while either of these is displayed, and it should enter CMOS setup once the initial cpu and memory tests are completed.
Let me know if you are still having problems after trying these suggestions. You can contact me directly if you want ([email protected]).
-Rusty

Similar Messages

  • How incremental backup is used in recovery

    Hi,
    how incremental backup is used in recovery let's say i took full backup on sunday then monday tuesday, wednesday took incremental backup. now on wednesday DB crash. so how incremental backup will use in recovery as i understand DB will restore from full backup then archive and increment backup will apply for recovery?
    please correct me if i am wrong.

    1) Backup FULL RMAN Level 0 - Sunday
    2) Backup FULL RMAN LEVEL 1 (incremental) - other days
    3) Backup Archives
    Restore Level0 + Restore Level1 + Apliying Archives and recover database;

  • How to recover hp pre-installed games and office after system restore for HP Mini 210-4127se?

    how to recover hp pre-installed games and office after system restore for HP Mini 210-4127se?

    Hi,
    You can reinstall them from Recovery Manager by clicking on Start=> All Programs.
    If you have performed a complete HP Recovery using F11 then all the software should be there. If you have performed a minimized recovery then you can install applications from recovery manager...If none of these works then you'll need USB recovery..
    Here are the links that will guide you through the process:
    Using Recovery Manager to Restore Software and Drivers (Windows 7)
    Performing an HP System Recovery (Windows 7)
    Order USB Recovery
    Note:
    If you have HP Support Assistant installed on the computer(The Blue Question Mark) then open it ==> Complete all pending Updates & Tuneups==> Restart and Check. It may solve your problem
    Although I am an HP employee, I am speaking for myself and not for HP.
    **Click on “Kudos” Star if you think this reply helped** Or Mark it as "Solved" if issue got fixed.

  • My macbook keeps asking me to use an administrator and their password to continue but nobody seems to know who is the administrator for this computer...does anyone know how to avoid this this or figure out who the administrator is?

    My macbook keeps asking me to use an administrator and their password to continue but nobody seems to know who is the administrator for this computer...does anyone know how to avoid this this or figure out who the administrator is?

    Lynne130,
    to figure out which users have administrative privileges, open the Users & Groups pane of System Preferences; each user other than the Guest User will be shown with a description of either “Admin” or “Standard”. It’s typical for the first user created on a Mac to be an administrative user.

  • How can I make Use of PS and Ai (offer) in spite of running Windows Vista ?

    How can I make Use of PS and Ai (offer) in spite of running Windows Vista ?

    Once you have signed up, you could - in theory - choose "other version" under the icon on the CC website and install CS6, but I'm not sure if that works for this special offer or only for "full" CC. Anyway, it seems simple enough to upgrade to Win 7 or Win 8 and perhaps you were planning on starting fresh, anyway...
    Mylenium

  • How best we can use the Rollback and RollbackAlways mechanism in Visual Studio Release Management Template

    Hello All,
    We need a clarification on Rollback and RollbackAlways in Release template.
    We checked a scenario for Rollback and RollbackAlways:
    In Release Template, we have the first activity as “Configure Application Pool” and then followed by a rollback action of “Create Application Pool”
    and “Create Web Site” then followed by "Code Deployment" via TFS build.
    We tested with 2 scenario’s:
    With App Pool and Web Site already existing: when triggered the build, configure
    app pool succeeded, then Rollback action was skipped (as previous action was successful), finally deploy the code executed (code deployed) and build got succeeded.
    Deleted App Pool and Web Site: when triggered the build, configure app pool failed (as no app pool existed), Rollback action executed (as previous action failed) – created app pool and web site then finally
    deploy the code executed (code deployed)
    But build failed (Error: Configure app pool action failed).
    Ideally the build should succeed as the roll back action got executed and code deployed successfully.
    Please correct us if our understanding is wrong.
    Also, Kindly let us know how best we can use the Rollback and RollbackAlways mechanism in Release Management
    Looking forward for your positive response.
    Thanks in advance.
    Regards,

    Hi Shashank,
    Rollback Always runs if any of the actions in the template failed. Rollback will run if action just above rollback fails or if any of the actions below the Rollback fails.
    Article here (http://www.incyclesoftware.com/2014/03/understanding-rollbacks-release-management/) clearly explains how Rollback and Rollback
    Always work.
    I think you come across this issue since you are using build to do the "code deployment" action. You should use the release template to do that. 
    As far as I know you cannot use Rollback to achieve condition check (App pool exist in your case) action.
    For this you can create your own Power Shell component (which checks if the app pool exist and is not create it) and add it as a tool in RM server (RM Server Inventory).
    Another option is you can follow the workaround in below thread "Answer" quoted below. That is execute Remove app pool regardless if it exist or not (which does not fail) and then create app pool.
    I was able to get it working by removing the app pool which does not fail if it doesn't exist. Removing then creating seems the long way around but it works.
    Flow:
    Remove Application Pool
    Create Application Pool
    https://social.msdn.microsoft.com/Forums/en-US/43bf21c8-e233-4e58-a5a8-2592b78bc466/vs-2013-release-management-create-application-pool-fails-if-it-already-exists?forum=tfsbuild
    Cheers!
    Chaminda

  • My wife had an iPad for a year and synced to our computer with no problem.  I recently received an ipad2 and when I tried to sync using separate apple and iTunes passwords, under her computer user name, it appears I over-road her account and synced all he

    My wife had an iPad for a year and synced to our computer with no problem.  I recently received an ipad2 and when I tried to sync using separate apple and iTunes passwords, under her computer user name, it appears I over-road her account and synced all her apps with my apps on my iPad.  I then set myself up as a new user on our computer and tried to sync.  I now get the error that my iPad is synced to another library.  How can I start over without erasing all my data on the iPad?

    Go back to her login.  Unless you deliberately erased apps, they should all be there, both yours and hers!  Then, you need to set up each iPad separately.  You will notice that they have separate names for that very purpose.
    There is no problem with multiple Apple IDs on the same iTunes on the same computer except...  Apps are permanently associated with the ID that was originally used to obtain them.  If you choose to update an app from inside iTunes and you're logged into the "wrong" ID, you must log out and back in again.
    On the bright side, you can configure either or both iPads to sync with apps and music and movies, etc. from either or both IDs.  Further, if you choose to update the apps from the iPads themselves, there is no need to log out/in.  The device handles that.  All you need is the correct password.  In my case, I use the same password for both IDs to make things easier.

  • I forget my icloud password... will u plz tell me how i recover it?, i forget my icloud password... will u plz tell me how i recover it?

    i forget my icloud password... will u plz tell me how i recover it?, i forget my icloud password... will u plz tell me how i recover it?

    How to reset your Apple ID password.
    Go to iforgot.apple.com and type in your Apple ID, then click 'Next'.
    Verify your date of birth, then click 'Next'.
    You'll be able to choose one of two methods to reset your password, either E-Mail Authentication or Answer Security Questions.
    If neither method works, then go to https://getsupport.apple.com
    (If you see a message that says 'There are no products registered to this Apple ID, simply click on 'See all products and services')
    Choose 'More Products & Services', then 'Apple ID'.
    A new page will open.
    Choose 'Other Apple ID Topics', then 'Lost or forgotten Apple ID password'.
    Click the blue 'Continue' button.
    Select the contact option that suits your needs best.

  • How to Recover database from old backup and full archive log file

    Hi Oracle expert!
    I met problem when restore my oracle database.
    In my case:
    - My database version: 10.2.0.2
    - I have a database full backup (01-Nov)
    - I have all Archived log file from (01-Nov -> 05-Nov)
    - My database drop in 05-Nov with disk error (no datafile, no redo..).
    - I have no any RMAN backup from (01-Nov -> 05-Nov)
    How can i restore my database to 05-Nov?
    Thanks

    user10280724 wrote:
    Hi Chinar.
    When i used RMAN flow as your step, but i met the problem!
    - After recover database i select sequence#, applied from v$archived_log;
    --> it apply newest archived log that i had.
    - but when I select Data from table created between 01-Nov to 05-Nov, it not found!
    Not the same way the step:
    SQL> RECOVER DATABASE USING BACKUP CONTROLFILE UNTIL CANCEL?
    It apply newest the same archived log i had table created between 01-Nov to 05-Nov.
    How can i do with RMAN to recover my table?That is not possible,if your all available archive logs applied using rman or through sqlplus(recover database using backup controlfile until cancel) and one of these logs contain your table then there are not any problems.So there are not any difference between recovery using rman and user managed(using sqlplus),but there main matter is applying all archive logs.So first check through rman list copy of archivelog all or list backup of archivelog all and identify there in rman repository is any information or not about these logs.

  • I am unclear how I have to use the Recovery CD

    I have added up all the space my hard disk is using it comes to about 12GB, I have 27.9 GB disk space but my disk only has 1.80 disk space left. I have done everything obvious to resolve this problem. Recycle bin is empty, I have run disk clean up.
    A computer expert suggested that Windows could have become confused and cannot recognize what space I have spare, this could be because I have run a program called Cyberscrub often. His solution was to reload Windows XP home. My laptop came with recovery disks, everything else already loaded. I have so much I do not want to lose on my laptop. If I use the recovery disks, will I lose everything on my computer, am I best to buy Windows XP home and re-load, in which case will I not lose my work?
    Also I am unclear how I use the recovery discs, I cannot find any instructions on what you do.
    The one person who could help me has gone off traveling and not contactable.
    Any help greatly appreciated
    Lorraine Hart

    Hello,
    what kind of programs do you have on your harddisk? Maybe a little description of your System will help us further. You mentioned, that you have a Program called Cyberscrub. Is this Program showing you your diskspace? Check this out! This program is, as i know, usually intended to wipe harddisks or files.
    Maybe you can try some Registry cleaner that cleanes out some information which is showing you wrong information that is corrupted by Cyberscrub. Maybe this helps.
    Another suggestion: run the program "chkdsk". This program will check out your filesystem on errors. Maybe it can fix that problem. You can run this program with right-clicking on the symbol of your systemdisk, clicking on "extras" and choosing the "Checking on errors" or something like.
    At all events, when this fails, then you dont have to buy a new XP Home. You dont need it because you have already one on a recovery cd, and you can solve that easily.
    You have to write down which programs you have in your system and backup your important data with a backup program or just burn it to a dvd or cd. You have the option to put the whole system on a mobile Harddisk connected over USB. This means backing up your system to this harddisk.
    After that, you have to boot with the recovery-cd, by pushing the "c" button at boot time.
    Then you follow the instructions and reload the "factory-like-installed" Windows XP on your Harddisk. Dont forget: all your data on the system disk will be erased, and the corrupted information of the free diskspace too. After that you just put the backup of your data back to your systemdisk and reinstall the programs you noted before the re-install of your system. Then the system will be clear again.
    Let me know about the activity of your problem.
    Greets

  • Re: Is it possible to completely recover VistaOS using only Recovery DVD?

    Hidden WinRE partition was deleted by mistake but I still got the original Recovery DVD for my A200.
    Is it possible to completely recover VistaOS without the WinRE partition, using only Recovery DVD?

    Of course.
    The Toshiba Recovery CD was designed to recover the notebook.
    Using the recovery CD you will get the factory settings.
    But note; the Toshiba recovery CD formats the whole HDD and erases the partitions from the HDD.
    Greets

  • How to recover iphoto library from recovery mode

    My macbook pro suddenly went on Utility Disk Mode and can only be accessed through recovery mode. I cannot even view the files. I'm willing to let everything go except for the photos and videos in the iphoto library. I don't know how to access my photos on icloud and when I did, it was just my iphone's photos that are there. is there any way I can view my photos in my locked macintosh hd in other devices or computer?

    Thanks for the response BDAqua, I did use Migration Assistant to transfer her data from the SuperDuper backup.  Are you suggesting that I use Migration Assistant to transfer data from the Time Machine backup?  Will that result in duplication?  Sorry, but I've no experience at all with Time Machine backups and don't know whether you can 'pick and choose' what to restore from the Time Machine using Migration Assistant.
    Cheers
    Tricia

  • How to recover lost product license keys and not just Microsoft licenses?

    Which products have you tried?  Have you looked at Magic Jelly Bean?  Depending on the OS and software, some keys are not retrievable.  You should also know that certain software are not transferable from one PC to another, reference the license terms of each for clarification. 

    There are so many products out there that claim to recover lost software license keys and all of the ones I've tried either recover only MS license keys or no keys at all.  I'm trying to recover keys from my fathers old system to install on his new one and some of the products he used do not have the keys available.  Anyone out there with a viable product key recovery tool that will get back more than just MS license keys?
    My father will be greatly pleased.
    This topic first appeared in the Spiceworks Community

  • How can recover database using only Full Export ?

    Hi,
    I have one query , i have only Full export is given database , after full export sucessfully
    database Crash by mistacally, how can recover it, i have only export is given no backup is taken (RMAN,COLD or HOT) statergy is use , How can recover it.

    You need to recreate the database from scratch as imp requires a working database.
    You could already do this by transforming the results from
    'alter database backup controlfile to trace', a trace file containing a 'create controlfile' statement, into a 'create database' script.
    After that step you apply your import. Everything after that import is lost forever.
    One would ask for a sanity check of management and personell of a company, which has no backup strategy in place.
    Sybrand Bakker
    Senior Oracle DBA

  • How to recover/update GUID_EXTERNAL between ODI and WLS

    HI All,
            I have lost my all security in a OBIA 11.1.1.7.1 environment, and I'm trying to recreate it. I've already recreated at WLS the following users biappsadmin (my OBIA admin user), BIAppsSystemUser and BISystemUser.
           I've got to log into OBIEE again, but when I try to log into ODI Studio I've got the following error :
    oracle.odi.core.security.BadCredentialsException: ODI-10163: This OPSS user biappsadmin has different GUID than the one found in Oracle Data Integrator repository.
    at oracle.odi.core.security.SecurityManager.createAuthentication(SecurityManager.java:511)
    at oracle.odi.core.security.SecurityManager.createAuthentication(SecurityManager.java:252)
    at oracle.odi.ui.docking.panes.OdiCnxFactory$1.run(OdiCnxFactory.java:208)
    at oracle.ide.dialogs.ProgressBar.run(ProgressBar.java:655)
    at java.lang.Thread.run(Thread.java:662)
         Then, looking at SNP_USER from <prefix>_BIA_ODIREPO I have the following :
      I_WUSER                    --> 2500
      WUSER_NAME          --> biappsadmin
      WUSER_INIT               --> null,
      PASS                         --> null,
      AUT_SUPERVISOR     -->1,
      FIRST_DATE               -->null,
      FIRST_USER               -->null,
      LAST_DATE               -->null,
      LAST_USER               -->null,
      IND_CHANGE               -->null,
      EXT_VERSION            -->null,
      EXPIRACY_DATE       ->null,
      I_TXT_DETAIL             -->null ,
      USER_EXPIRACY_DATE --> null,
      GUID_EXTERNAL          --> 7D635A9155BD11E38F07A52086C80F5C
        So, Is there a way to know what is the GUID that WLS has created to this user  ? If dont, How to recover the security ?
    Thanks in advance...

    Mr.Elendig wrote:Will work fine if you have the PKGBUILD build it against the installed kernel instead of the running one.
    I googled it, but can't find the solution. Would you explain it a bit, for example, the PKGBUILD below, how to change it to let it compile against a specific version kernel? Thanks.
    pkgname=('zfs')
    # When changing versions, search and replace 0.6.0-rc11, using package
    # variables breaks AUR parsing.
    pkgver=0.6.0_rc11
    pkgrel=2
    arch=('i686' 'x86_64')
    pkgdesc="Native ZFS for Linux"
    url="http://zfsonlinux.org/"
    depends=('linux-lts>=3.0' "spl>=${pkgver}" "zfs-utils>=${pkgver}")
    makedepends=('linux-lts-headers>=3.0')
    source=(http://github.com/downloads/zfsonlinux/zfs/zfs-0.6.0-rc11.tar.gz
    zfs_preempt.patch
    md5sums=('85435c100d9c1dadad7b961c3cb965f6'
    '13d63bbc0497ccc03d982817b6319512')
    license=('CDDL')
    install=zfs.install
    build() {
    cd ${srcdir}/zfs-0.6.0-rc11
    patch -p0 -i ${srcdir}/zfs_preempt.patch
    ./autogen.sh
    ./configure --with-config=kernel \
    --prefix=/usr \
    --sysconfdir=/etc \
    --sbindir=/usr/sbin \
    --libdir=/usr/lib \
    --datadir=/usr/share \
    --includedir=/usr/include \
    --with-udevdir=/lib/udev \
    --libexecdir=/usr/lib/zfs-0.6.0-rc11
    make
    package() {
    cd ${srcdir}/zfs-0.6.0-rc11
    make DESTDIR=${pkgdir} install
    # move module tree /lib -> /usr/lib
    cp -r ${pkgdir}/{lib,usr}
    rm -r ${pkgdir}/lib

Maybe you are looking for