How to reinitialize the sel screen after displaying the output..?

Hi All,
I have a report program. In the selection screen, I will provide the input parameters and execute the program which displays the output on the screen. Now, if I come BACK to the selection screen, the values which I entered earlier will appear on the selection screen. My requirement is... If I come BACK from the output screen to the selection screen, the selection screen should be blank. I mean, all the values I entered earlier should be cleared. Could anyone please tell me how to do that.
Thanks in advance.
Best regards,
Paddu.

Hi Paddu,
the selection screen will be reinitialized automatically. Only if the INITIALIZATION event or the parameters use SET/GET parameter IDs (addition MEMORY ID pid) the values will prevail.
You may clear everything in INITIALIZATION event.
Regards,
Clemens

Similar Messages

  • Can I disable the LCD screen from displaying the Network Name or Password of my device?

    Can I disable the LCD screen from displaying the Network Name or Password of my device?  I feel that having this information readily available to any who can turn on my device is a security flaw.
    I have change the network name and password and would like to secure that information .

    Worked with VZW tech support and finally found where you can disable or mask  the display of the network name and password on the Jetpack LCD screen.  You need to access the admin screen of your jetpack (http://my.jetpack/) .  From there, navigate to Jetpack Settings --> Click on Wifi tab -- Click on the Wi-Fi Options link halfway down the page and it will show the two settings that control the display of network name and password.
    As they say, a picture is worth a thousand words...here are screen shots showing how to get to these settings. ...
    The LCD display will show ********* for the network name and password if the two checkboxes above are unchecked. I really think these settings should be disabled to be begin with.
    Oh well...posting here to share with those interested...

  • How to avoid the logon screen after closing the browser

    Im working with annonymous users showing a Iview but when I close the browser, instead of closing the browser the logon of portal appears. I dont want that how can I avoid this ?
    thx

    Hi
    I am not clear with your question. How do you close the browser ? Is it by hitting the cross button on the Top right corner ?
    Murali.

  • HT201412 Does not return to the Home screen after pressing the Home button

    My home button it's not works after pressing If I press it hard many time it's work but sometime not working at all. Can any apple store fixed this problem in any apple store at any country cause I purchased from apple stroe in Brighton and I live in Kuwait .. So please help me with this problem
    thank you for listen

    Check the following:
    1. Check credit card number
    2. Check security code
    3. Billing Address must be the same as credit card
    4. Check expiry date
    5. Make sure you have sufficient fund

  • Blank screen after rotating the display in Yosemite (MacBook Pro Late 2013)

    Hi,
    after installing Yosemite on my MacBook Pro 15" Late 2013 I have trouble rotating it's screen. After I launch Preferences and click Displays while pressing alt and command keys I see the list of possible orientations available.
    If I now select 270° the screen immediately goes black. To be clear: The display is not turned off like when the MacBook sleeps. It's still lit, but only shows a black screen. After turning the MacBook off by pressing and holding the power button I can boot and voilà, the screen is perfectly normal, showing everything rotated at 270°. If I reset to Landscape from there (i. e. 0°), I have no problem at all, everything still works. Setting it back to 270° again lets the screen go black again.
    I have an installation of Mavericks at my primary partition and it has no problems at all with rotation. Is this a known bug or can anyone confirm this behaviour?
    As a hint for others suffering the same problem: You can get around the hard reset by pressing shift-comand-q followed by enter key. This logs your user out of the system and gets you back to the login screen. This obviously kind of reinitializes the UI. After that, the display's rotation is working and you just have to login again.
    Even if this is some kind of workaround it would still be much more convenient not requiring this workaround.
    Thanks in advance,
    Oliver

    Hi,
    yes, I had the same issues here! My solution was to force the system to use the discrete graphics card instead of the intel one. Then you get some additional options for the resolution which are much more usable. If you need further infos let me know. I'm using the MacBook in a rotated state about 95% of the time and it works pretty well now (at least in Mavericks, where I also experience your described behaviour).
    Greetings,
    Oliver

  • How to get rid of the on screen volume display?

    how to get rid of the on screen volume display, it stays on even after reboot. and when i hit the volume button another one shows on top of it.

    Sounds like a key on the keyboard is stuck down. Does it disappear if you disconnect the keyboard?

  • I have an ipod touch 8gb model number MA623LL. How do I install apps on my ipod? Is it capable of transferring/running apps? Why doesn't my ipod touch have the basic-beginning app on the beginning screen after i erased/wiped my ipod and started new?

    i have an ipod touch 8gb model number MA623LL. How do I install apps on my ipod? Is it capable of transferring/running apps? Why doesn't my ipod touch have the basic-beginning app on the beginning screen after i erased/wiped my ipod and started new?

    Googling shows that you have the 1G iPod.  For apps you need at least iOS 2. The iG can go as far os 3.1.3 that you get here:
    Purchasing iOS 3.1 Software Update for iPod touch (1st generation)
    Just be aware that there are presently not that many apps that work with a 1G with iOS 3.1.3

  • Accidentally exited out of the loading screen after making my purchase, should I retry or how do I check if the payment went through?

    Accidentally exited out of the loading screen after making my purchase, should I retry or how do I check if the payment went through?

    check your account, https://www.adobe.com/account.html

  • How to enable the screen after triggering the error message

    Hi All,
    we have a tcode IW31, in that one field(WBS element -PROID) is not mandatory. so we have written the following code to make it mandatory in a user exit EXIT_SAPLCOIH_010.It's triggering the error message, but it is going into disable mode. Please sugget me how to enable the screen after getting the error message triggering.
    if not caufvd_imp-proid is initial.
      select single * from t350 into wa_t350
              where  auart    = caufvd_imp-auart
                and  imord    = 'X'.
      if sy-subrc is initial.
        pspel = caufvd_imp-proid.
      else.
        call function 'CONVERSION_EXIT_ABPSP_OUTPUT'
             exporting
                  input  = caufvd_imp-proid
             importing
                  output = l_posid.
        concatenate text-t10 l_posid text-t11
                    into l_textline1 separated by space.
        message i208(00) with l_textline1.
      endif.
    else.
      message e208(00) with 'Please maintain WBS element in Location Tab'.
    endif.
    Thanks

    Hi,
    Instead of error message use status message like
    message s208(00) with 'Please maintain WBS element in Location Tab'.
    Leave to screen sy-synnr.
    This will allow to move to the screen and have in enable mode.
    WIth Regards,
    Dwaraka.S
    Edited by: Dwarakanath Sankarayogi on Feb 13, 2009 7:46 AM

  • I can't get past the gray screen after update of 10.10.3

    downloade the new software on my 2011 Mac this morning, and after the download when the computer restarts a gray screen appear. I don't know how to get rid of it. It was working fine before the updat. Anyone have this problem?

    Take each of these steps that you haven't already tried. Stop when the problem is resolved.
    To restart an unresponsive computer, press and hold the power button for a few seconds until the power shuts off, then release, wait a few more seconds, and press it again briefly.
    Step 1
    The first step in dealing with a startup failure is to secure the data. If you want to preserve the contents of the startup drive, and you don't already have at least one current backup, you must try to back up now, before you do anything else. It may or may not be possible. If you don't care about the data that has changed since the last backup, you can skip this step.
    There are several ways to back up a Mac that is unable to start. You need an external hard drive to hold the backup data.
    a. Start up from the Recovery partition, or from a local Time Machine backup volume (option key at startup.) When the OS X Utilities screen appears, launch Disk Utility and follow the instructions in this support article, under “Instructions for backing up to an external hard disk via Disk Utility.” The article refers to starting up from a DVD, but the procedure in Recovery mode is the same. You don't need a DVD if you're running OS X 10.7 or later.
    b. If Step 1a fails because of disk errors, and no other Mac is available, then you may be able to salvage some of your files by copying them in the Finder. If you already have an external drive with OS X installed, start up from it. Otherwise, if you have Internet access, follow the instructions on this page to prepare the external drive and install OS X on it. You'll use the Recovery installer, rather than downloading it from the App Store.
    c. If you have access to a working Mac, and both it and the non-working Mac have FireWire or Thunderbolt ports, start the non-working Mac in target disk mode. Use the working Mac to copy the data to another drive. This technique won't work with USB, Ethernet, Wi-Fi, or Bluetooth.
    d. If the internal drive of the non-working Mac is user-replaceable, remove it and mount it in an external enclosure or drive dock. Use another Mac to copy the data.
    Step 2
    If the startup process stops at a blank gray screen with no Apple logo or spinning "daisy wheel," then the startup volume may be full. If you had previously seen warnings of low disk space, this is almost certainly the case. You might be able to start up in safe mode even though you can't start up normally. Otherwise, start up from an external drive, or else use the technique in Step 1b, 1c, or 1d to mount the internal drive and delete some files. According to Apple documentation, you need at least 9 GB of available space on the startup volume (as shown in the Finder Info window) for normal operation.
    Step 3
    Sometimes a startup failure can be resolved by resetting the NVRAM.
    Step 4
    If a desktop Mac hangs at a plain gray screen with a movable cursor, the keyboard may not be recognized. Press and hold the button on the side of an Apple wireless keyboard to make it discoverable. If need be, replace or recharge the batteries. If you're using a USB keyboard connected to a hub, connect it to a built-in port.
    Step 5
    If there's a built-in optical drive, a disc may be stuck in it. Follow these instructions to eject it.
    Step 6
    Press and hold the power button until the power shuts off. Disconnect all wired peripherals except those needed to start up, and remove all aftermarket expansion cards. Use a different keyboard and/or mouse, if those devices are wired. If you can start up now, one of the devices you disconnected, or a combination of them, is causing the problem. Finding out which one is a process of elimination.
    Step 7
    If you've started from an external storage device, make sure that the internal startup volume is selected in the Startup Disk pane of System Preferences.
    Start up in safe mode. Note: If FileVault is enabled in OS X 10.9 or earlier, or if a firmware password is set, or if the startup volume is a software RAID, you can’t do this. Post for further instructions.
    Safe mode is much slower to start and run than normal, and some things won’t work at all, including wireless networking on certain Macs.
    The login screen appears even if you usually log in automatically. You must know the login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin.
    When you start up in safe mode, it's normal to see a dark gray progress bar on a light gray background. If the progress bar gets stuck for more than a few minutes, or if the system shuts down automatically while the progress bar is displayed, the startup volume is corrupt and the drive is probably malfunctioning. In that case, go to Step 11. If you ever have another problem with the drive, replace it immediately.
    If you can start and log in in safe mode, empty the Trash, and then open the Finder Info window on the startup volume ("Macintosh HD," unless you gave it a different name.) Check that you have at least 9 GB of available space, as shown in the window. If you don't, copy as many files as necessary to another volume (not another folder on the same volume) and delete the originals. Deletion isn't complete until you empty the Trash again. Do this until the available space is more than 9 GB. Then restart as usual (i.e., not in safe mode.)
    If the startup process hangs again, the problem is likely caused by a third-party system modification that you installed. Post for further instructions.
    Step 8
    Launch Disk Utility in Recovery mode (see Step 1.) Select the startup volume, then run Repair Disk. If any problems are found, repeat until clear. If Disk Utility reports that the volume can't be repaired, the drive has malfunctioned and should be replaced. You might choose to tolerate one such malfunction in the life of the drive. In that case, erase the volume and restore from a backup. If the same thing ever happens again, replace the drive immediately.
    This is one of the rare situations in which you should also run Repair Permissions, ignoring the false warnings it may produce. Look for the line "Permissions repair complete" at the end of the output. Then restart as usual.
    Step 9
    If the startup device is an aftermarket SSD, it may need a firmware update and/or a forced "garbage collection." Instructions for doing this with a Crucial-branded SSD were posted here. Some of those instructions may apply to other brands of SSD, but you should check with the vendor's tech support.  
    Step 10
    Reinstall the OS. If the Mac was upgraded from an older version of OS X, you’ll need the Apple ID and password you used to upgrade.
    Step 11
    Do as in Step 9, but this time erase the startup volume in Disk Utility before installing. The system should automatically restart into the Setup Assistant. Follow the prompts to transfer the data from a Time Machine or other backup.
    Step 12
    This step applies only to models that have a logic-board ("PRAM") battery: all Mac Pro's and some others (not current models.) Both desktop and portable Macs used to have such a battery. The logic-board battery, if there is one, is separate from the main battery of a portable. A dead logic-board battery can cause a startup failure. Typically the failure will be preceded by loss of the settings for the startup disk and system clock. See the user manual for replacement instructions. You may have to take the machine to a service provider to have the battery replaced.
    Step 13
    If you get this far, you're probably dealing with a hardware fault. Make a "Genius" appointment at an Apple Store, or go to another authorized service provider.

  • How to populate the next screen based on the previous screen table control

    Hi Experts,
            Is this possible to generate the next screen values based on the table control values in previous screen.
    My Requirement is
    In my First screen i m having 5-7 regional offices in table control and also amount field for each regional offices.(amount field is editable)
    User has to enter amount field for Regional office..based on the amount field i need to process the next screen. For Ex if user is entering  amount for 3 regional offices out of 7 regional offices then i need to get the screen for the 3 regional offices..
    Pls suggest me how to do this..
    Regards,
    Zakir

    Hi Zakir,
    Do you have any button for calling the second screen after entering amount in the first table control screen or you have to call the screen on pressing enter on the table control?
    You will have to handle it in the PAI of the table control loop.Get data entered in the table control in your internal table of table control.You can prepare the data passed to the next screen from this internal table. Fill the second screen elements and Use CALL SCREEN XXX. XXX is your second screen no.
    Thanks,
    Pawan

  • Sent long message 4s now message program will not open. Tries to load but returns to the home screen after a while

    Sent long message 4s now message program will not open. Tries to load but returns to the home screen after a while. How can I open my messages?

    close all backgrounded apps, and then try,if it crashes again then do a reset all settings

  • Hi, I am trying to download IOS7 to my ipad. The programme has locked at the 'Choose a Wif-Fi network' page, a box says 'joining other network' but the page is greyed out and can't move from it.  How can I clear this screen and finish the download. Thanks

    Hi, I am trying to download IOS7 (not sure if it's 1 or 2) to my ipad. The programme has locked at the 'Choose a Wif-Fi network' page, a box says 'joining other network' but the page is greyed out and can't move from it.  How can I clear this screen and finish the download. Thanks

    Hello Den53,
    Thanks for using Apple Support Communities.
    For more information on this, take a look at:
    iOS: Turning off and on (restarting) and resetting
    http://support.apple.com/kb/HT1430?viewlocale=en_US
    Press and hold the Sleep/Wake button for a few seconds until the red "slide to power off" slider appears, and then slide the slider.
    After the device has turned off, press and hold the Sleep/Wake button until the Apple logo appears.
    Best of luck,
    Mario

  • How to report print to the printer immediately and display the popup?

    Dear friends,
    I am running my report in background and displaying the confirm results on popup window and sending the results to printer,
    but now i want to send the results page to printer then  want to display the popup.
    i have writen my popup perform after printer perform only but its not working...when i am clossing the popup or came back from that popup then only the results sending to printer...
    How to report print to the printer immediately and display the popup?
    Thanks in advance
    Sridhar

    Hi Sudheer,
    I am using my print parameters like this :
        NEW-PAGE PRINT ON DESTINATION ws_printer
                             IMMEDIATELY 'X'
                             KEEP IN SPOOL 'X'
                             NEW LIST IDENTIFICATION 'X'
                             SAP COVER PAGE 'X'
                             ARCHIVE MODE '1'
                             LINE-COUNT 64
                             LINE-SIZE 170
                             NEW-SECTION
                             NO DIALOG.
    Then also its not printing immediatly.
    here one thing for displaying the popup i am using submit report(calling another report for popup purpose)
    before trigering the submit programe i need to print this.
    Thanks
    Sridhar.

  • My iPod is stuck on the startup screen, showing just the apple logo. Has anyone had this problem before? If yes, then how did you solve it?

    My iPod is stuck on the startup screen, showing just the apple logo. Has anyone had this problem before? If yes, then how did you solve it?

    Try:
    - iOS: Not responding or does not turn on
    - Also try DFU mode after try recovery mode
    How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
    - If not successful and you can't fully turn the iOS device fully off, let the battery fully drain. After charging for an least an hour try the above again.
    - Try on another computer
    - If still not successful that usually indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order.
    Apple Retail Store - Genius Bar       

Maybe you are looking for