How to reinstall os x/data after replacing hard drive

I'm about to replace my hard drive after the original crashed. I have a macbook pro 17" and I have the original backup cd's, also a time machine backup on external hd.I'm installing a 1tb hdd from the 750gb original.
What is the sequence which I need to follow to restore my OS and data? The original OS is Snow Laopard, the one I ugraded to is Moutain Lion.
Apart from the sequence will the Ext hd have the operating system backed up on it or do I need to load the original OS disc and then the Apps disc or only the Ext hd backup?
As I'm replacing my hard drive do I need to format the new drive in disc utilities still, if so how?
Will I be asked for any passwords?
Any help appreciated.
Martyn.

Install the new HDD in your MBP.
Start the MBP with the Snow Leopard install disk holding down the C key.
Proceed with the installation until you see a menu bar on top of the display.
From the menu bar click on UTILITIES.
From the drop down menu select Disk Utility.
Select Disk Utility>Erase and format the HDD to Mac OS Extended (Journaled).
Proceed to install Snow Leopard. It will probably be 10.6.3.
Open SOFTWARE UPDATE and install 10.6.8.
Then you may install Mt. Lion or Mavericks.
Run Time Machine and install your user data. Refer to this web site for assistance if need be:
http://pondini.org/OSX/Home.html
Ciao.

Similar Messages

How do I restore my data after my hard drive was replaced?

The hard drive in my iMac failed after I upgraded to Mountain Lion last week. The drive has been replaced and I'd like to restore files from my Time Capsule, if this is possible. However, when I enter Time Machine, there is a long wait while a dialogue box says "Connecting to backup volume" and then, when it becomes available, there are no previous dates before today listed and I can't move backwards, as I've done previously. I know that backups exist because I've used Time Machine before to restore files I've worked on to previous versions - and the capsule is still telling me that it's very nearly full of data. Is there a way to restore to a new hard drive, or is that asking too much of Time Machine? Please forgive my ignorance. I'm worried that I've lost a LOT of irreplaceable files.

Hi again. Okay, so I'm a little embarrassed because I just needed to wait and have faith. I'll leave this here for anyone who is panicking like I was today.
Essentially, I had to allow Time Machine to install a new back-up on the Time Capsule. I resisted this for a while and thought I'd made a mistake in allowing it when it had to discard an old back-up to fit the new one onto the machine. At this point, I was worried that I was losing a valuable older back-up in place of one of an empty-ish drive. But, once this back-up had completed, I was finally able to travel backwards and see the contents of my previous hard drive. I've currently restored my desktop and some personal files and tomorrow I'm going to go for the big targets, like my iTunes library.
Thanks, Apple.

How do I reinstall CS6 Extended 64-bit after replacing hard drive and OS?

How do I reinstall CS6 Extended 64-bit after replacing hard drive and Windows 7 64-bit OS?

You can download the trial installer directly. Find the appropriate link below.
You must be on a trial download page to use the links, otherwise you get an error message.
For example, load the following page: http://www.adobe.com/cfusion/tdrc/index.cfm?product=photoshop_elements&loc=us
before pasting the link into the address bar.
http://trials2.adobe.com/AdobeProducts/PHSP/13/win32/Photoshop_13_LS16.7z
http://trials2.adobe.com/AdobeProducts/PHSP/13/win32/Photoshop_13_LS16.exe
You need to kepp both files downloaded into same folder and after download click on .exe file to extract .7z

MacBook Pro does not boot past apple screen after replacing hard drive

After replacing hard drive on MacBook Pro 13 inch early 2011 model, the screen only boots to the apple logo. Do I need to re-install the OS?

The problem is that the OS is not in any where else of the MacBook Pro than in the HD / SSD. If you replace the Hard Drive, then you will need to Re-install OSX into that hard drive, it's pretty easy.
1) Power up your Macbook Pro, as fast as you can press and hold the Option key (ALT). You'll see that it opens the bootable-devices you have, you'll see a Recovery partition, click it.
(If the Hard Drive contains data do the following)
2) In the menu select Disk Utility.
3) In Disk Utility go ahead and select the Hard Drive that is inside the MBP.
4) Erase the content.
(If the Hard Drive contains no data continue with the following jumping the last 3 steps).
5) Select Re-install OSX.
6) Select the Hard Drive in which you want to install it.
Follow the steps of everything else (it should take approximately 1 hour to do the whole thing).
Hope this helps!
Later.

Hi,disc wiped ,OSX10.9 back on ,how do I restore my data from external hard drive ?Any help welcome .

Hi,disc wiped ,OSX10.9 back on ,how do I restore my data from external hard drive ?Any help welcome .

There's Setup Assistant and Migration Assistant. The cleanest way to do it is Setup Assistant, but you only get that option once when you fire up a fresh install of OSX. If you're past that, you could reinstall OSX by booting with Command-R, or you could use Migration Assistant.
Setup/Migration Assistant instructions:
http://support.apple.com/kb/HT5872

HT201250 How to restore laptop from time capsule after replacing hard drive

How do I reload all my programs and files from a time capsule after changing hard drive? Also Apple store reloaded with Snow Leopard and not Lion. Will that be a problem? Thank you

Plug the external drive into a computer by usb or whatever box you have available..
When you say blank, is it correctly formatted.. we recommend HFS+ which is Mac OS Extended (jorrnaled)
Make sure you use GUID type disk setup not MBR if it came from PC world.
Copy the files via finder from TC to the external drive.

How to reinstall os x 10.7 after replacing hard drive?

Hi,
Can anyone tell me how I can reinstall my purchased copy of OS X 10.7 (Lion) to my new hard drive. The hard drive in my imac recently died. I had to replace with a new one. It is currently running on 10.6.8 (snow leopard) because I used the CD to put on the OS after formatting. However, I prior to the dead drive, I purchased a Lion and was running on Lion. My purchase was on line so there is no CD. How can I make this upgrade again? Do I have to pay apple again for Lion?
Thanks

You will ultimately have to download it over the Internet. Or I don't know, you could take your computer to an Apple Store and have them do it.
http://arstechnica.com/apple/2012/07/how-to-create-a-bootable-backup-mountain-li on-install-disk/

Reinstalling OS9 onto )S10.4.x after replacing hard drive ??

Don't know if this is the correct place to ask, but here goes. I think I posted this in the wrong place yesterday.
I had a catastrophic hard drive failure on my G5 and had to have a new hard drive installed. The repairman also reinstalled OS X from my disk.
When I tried to install OS 9 from the Install Disk, it won't do it. It says "There is nothing to install." Also, the "space needed" says 0.
I have read the Apple help site suggestions, but that involves deleting my OS 10.4, installing OS 9, reinstalling 10.2, then updating to 10.4. I don't want to do that, for a couple of reasons:
1. I am not going to deliet my OS...I am not computer literate enough to be comfortable doing that;
2. How do I know OS 9 is "really" on the install disk, since it says there is nothing there?
Anybody have any ideas.
Thanks,
Andy in AZ
USN 1964-1967
NAM 1966-1967

Andy:
Sorry! Bad news!
Did you try the procedure outline in the article linked by eww? If you did and it didn't work, here's what's next:
+Do I have to go through the whole procedure of deleting OS 10.4, installing 10.2, trying to install OS 9, and updating 10.2 to 10.4?+
Not quite all of that.
Here's what we will need to do:
1. Backup everything on your HDD you need to save.
2. Reformat from OS 9.
3. Install OS 9
4. Install OS X (10.4x)
Here's how:
Format and Install OS 9
This process will completely erase everything on your Hard Disk Drive. Be sure to Backup your User Folder and all third party apps you can't afford to lose
1. Boot from your OS 9 install CD holding down C key.
2. Go to Drive Setup and reformat your drive as Mac OS Extended (HFS+)
2. Reinstall OS 9
3. Update to 9.2.2: Mac OS 9: Available Updates
4. Update your firmware
5. Shut down computer and boot from OS X install disk as follows.
OS X Installation Process
Boot from you install disk holding down the "C" key.
When booted, select language.
Go to Utilities menu and launch Disk Utility.
Go to File menu and Repair OS 9 Permissions!
Quit Disk Utility.
Open Installer and begin installation.
Choose to Customize and deselect Foreign Language Translations and Additional Printer drivers.
Check box to install X11 (Tiger) BSD Subsystems (Panther & earlier).
Proceed with installation.
After installation computer will restart for setup.
After setup, reboot computer.
Go to Applications > Utilities > Disk Utility.
Select your HDD (manufacturer ID) in left side bar.
Select First Aid in main panel.
Click Repair Disk Permissions.
Connect to Internet.
Download and install Mac OS X 10.4.9 Combo Update (PPC) or 10.4.10 Combo update
Computer will restart after updates.
Go to Applications > Utilities > Disk Utility.
Select your HDD (manufacturer ID) in left side bar.
Select First Aid in main panel.
Click Repair Disk Permissions.
Please post back with questions or comments should you have any.
Good luck.
cornelius
Message was edited by: cornelius

Pavilion dv5 2035dx - reinstalling after replacing hard drive

My hard drive in my Pavilion dv5 2035dx failed -every test imaginable and I could not get Windos 7 to load. I purchased a replacement drive that is an exact dupilcate of the original Toshoba 500 and installed in my laptop. I was not too concerned since I had created my backup disks and had them in my possession.
Well I put the system repair/boot disk in and everything went alon fine, until I was asked to put in my other disks. None of the other disks seem to have the information my notebook is looking for and I can not install the drivers or get the machine up and running. I've checked the HP website and can nt find a recovery kit.
I was unable to get to Windows on the old defective drive to and since I have replaced the drive, there is no restore poit to look for so I have to reinstall back to the day of purchase. I need help, any suggestions on getting my notebook up and running again.

If in the USA, please see Windows 7 64b + Supp 3 Recovery Kit to purchase the HP Recovery Media for your computer. If elsewhere in the world, please contact official HP Customer Support, via the HP Worldwide Support Portal, to see if HP recovery Media is available for your model.
If you have any further questions, please don't hesitate to ask.
Please click the White KUDOS "Thumbs Up" to show your appreciation
Frank
{------------ Please click the "White Kudos" Thumbs Up to say THANKS for helping.
Please click the "Accept As Solution" on my post, if my assistance has solved your issue. ------------V
This is a user supported forum. I am a volunteer and I don't work for HP.
HP 15t-j100 (on loan from HP)
HP 13 Split x2 (on loan from HP)
HP Slate8 Pro (on loan from HP)
HP a1632x - Windows 7, 4GB RAM, AMD Radeon HD 6450
HP p6130y - Windows 7, 8GB RAM, AMD Radeon HD 6450
HP p6320y - Windows 7, 8GB RAM, NVIDIA GT 240
HP p7-1026 - Windows 7, 6GB RAM, AMD Radeon HD 6450
HP p6787c - Windows 7, 8GB RAM, NVIDIA GT 240

How do I get LR4 to find all photos in catalog after replacing hard drive on mac? question marks all

I had the hard drive replaced on my mac. I did a restore from back up drive to my new hard drive. First LR4 couldn't find the catalog so I pointed to it. Then I opened lightroom 4 and it cannot see ANY of my photos. I don't want to link each folder full of photos it will take hours. Isn't there another way to do this so it finds them all at once? Photos are still located in the same location on the new hard drive after restore. Nothing changed except the hard drive. Thank you!

I did find something in another post that suggests to go to the top most file in the structure and right click and click on "find missing folder" then you point to that folder and it will find all subfolders and photos. This really worked well for most of the photos but I have I must have moved at some point that I will have to relocate. This is good information whether you are working with a Mac or a PC. I think it would work for either. I hope this helps someone else out there.

How to reload my library after replacing hard drive

I have a 4G iPod nano. I think its probably second generation, but I'm not positive and not sure how to find out. I'm running Windows XP on a Compaq laptop.
The hard drive in my computer went bad and I had to replace it. Now my iTunes library is empty and the only option I'm given is to replace the library on the iPod with the one in iTunes (the empty one). I don't want to lose my songs, but I don't know how to get them back into my library. Since iTunes wasn't affected by the bad hard drive, I copied my entire library from its folder on the old hard drive onto an external hard drive. I tried placing all of that into the same folder on the new hard drive, but iTunes still shows me an empty library.
How can I get my songs back into my library so that I can get more tunes and sync again?

Had same problem and this thread really saved me. Here was my issue and your thread fixed it. Thanks
So I brought my PC in to a local shop that added an internal HD for me. They moved MY Music folder with the iTunes library to another drive (the new one). I open iTunes and nothing is there. How do I get the library with all my music and ringtones back into iTunes. I have searched here and other forums and only talks about moving library away to aother places. I have no trouble with it being on the new drive just want iTunes to see it. This has to be easy and I hope someone can help me. Thanks. I have windows XP if that matters. I can find the iTunes folder with all the music on what is now the D drive.
Signed, affraid to synch my iPhone until the library is back to normal

How to get system restored after replacing hard drive.

Bought a MacBook Pro about two years ago, hard drive failed and was replaced. Any way to get my iphoto, imovie, etc back on computer without having to pay for it since it originally came with the computer when I bought it?

If you did not buy the computer with Lion or Mountain Lion pre-installed, then you can reinstall these applications from the original installer discs that came with your computer.
If Lion or Mountain Lion was pre-installed, then re-download the applications from the App Store.

How to reinstall CS3 on newer mac when hard drive is replaced?

Adobe tech support won't help me. Need to find way to download CS3 for my computer. Hard drive replaced and software disappeared.

You can download the installer from the link at the bottom of this page: Download and Installation Help

How to re-activate Photoshop CS2 after my hard drive was replaced

Help! My hard drive had to be replaced, and now my computer will not allow me to use my Photoshop CS2. I purchased this years ago, and have all of the verification codes. I have several things I am working on that I can't finish until I get it reactivated. Help!!

Please do a forum search on "activate cs2". It has been discussed ad nauseam here.
Short answer: Adobe has taken down the CS2 activation servers. For legitimate licensees of CS2, it has posted a special version of CS2 that requires no activation but does require a new serial number, free to legitimate owners of CS2.

Pismo does not boot after replacing hard drive

We have had an old Pismo for several years now. Two or so years ago we decided to replace the stock 6GB hard drive, which was getting full, with a new 60GB drive. We cloned the old drive via target disk mode, popped in the new drive, copied the data back (again via target disk mode), and were surprised when we were met with the flashing question mark/system folder icon. Sort of left it at that and forgot about it.
I stumbled upon the Pismo again today and decided to see if I couldn't get it working. After going through a few "why won't this even turn on" sessions (the machine hadn't been powered on in a few years, so pulling the internal battery and resetting the PMU fixed that), I popped the old drive back in and the machine booted just fine. Cloned the original drive (again) using Carbon Copy Cloner via target disk mode to a disk image on my MacBook. Powered it down, put the new (60GB) drive back in the Pismo, cloned the disk image back to the new drive. The data's there, because I can browse it in target disk mode, but I can't boot off the new hard drive. I can't boot off my Tiger install DVD either - the DVD drive spins up and tries to access the disc, but won't boot. I'm going to try and get my hands on the CD version of Tiger to see if there's a difference using that.
Disk Utility on the MacBook says there's nothing wrong with the Pismo's hard drive, but I'm not convinced that's the case. I'd heard about Pismos being picky with certain types of hard drives, is this true? If not, what other issues might be leading to this behavior?

Is this perhaps an artifact of the drive being formatted via target disk mode on my MacBook
I suspect that the problem lies somewhere in that situation. I suggest that you boot from the install disk as I suggested previously and reformat the HDD and reinstall the OS.
Formatting, Partitioning Erasing a Hard Disk Drive
Warning! This procedure will destroy all data on your Hard Disk Drive. Be sure you have an up-to-date, tested backup of at least your Users folder and any third party applications you do not want to re-install before attempting this procedure.
• Boot the MacBook Firewire Target Disk Mode.
• Insert install disk into MacBook's optical drive.
• Connect computers via firewire cable
• Option Boot Pismo.
• Select Install Disk for startup and click on the straight arrow.
• Select language
• Go to the Utilities menu (Tiger and later) Installer menu (Panther & earlier) and launch Disk Utility.
• Select your HDD (manufacturer ID) in left side bar.
• Select Partition tab in main panel. (You are about to create a single partition volume.)
• Click on Options button
• Select Apple Partition Map (PPC Macs)
• Click OK
• Select number of partitions in pull-down menu above Volume diagram.
(Note 1: One partition is normally preferable for an internal HDD.)
• Type in name in Name field (usually Macintosh HD)
• Select Volume Format as Mac OS Extended (Journaled)
• Click Apply/Partition button at bottom of panel.
• Select Erase tab
• Select the sub-volume (indented) under Manufacturer ID (usually Macintosh HD).
• Check to be sure your Volume Name and Volume Format are correct.
• Click Erase button
• Quit Disk Utility.
Open installer and begin installation process.
cornelius

How to reinstall os x/data after replacing hard drive

Similar Messages

Maybe you are looking for