"how to Remove message, this call is unlimited"

When I go to make a call ,,,,, "how to Remove message, this call is unlimited"

Thanks for the information Poppz!
Let me help you get to the bottom of this! Please contact a Prepaid representative for answers. In order to reach a Prepaid Department representative, please call 888-294-6804. When prompted, enter your prepaid phone number. Then press 4, 5, 4 and enter the pass code for your account. If you do not know the pass code, enter in four zeros. Then the system will then transfer you to a Prepaid representative.
Thanks,
ChristinaB_VZW
VZW Support
Follow us on Twitter @VZWSupport

Similar Messages

How do i remove the message: "the time allowed for this call is unlimited?"

I want delete the message that sounds when i call someone that says: the time allowed for this call is unlimited.

johnnytitleist,
Thanks for that information! I recommend reaching out to our Prepaid experts to assist with this message. You can reach them at 888-294-7937.
SandyS_VZW
Follow us on Twitter @VZWSupport

How do i turn off that recording that says the time left for this call is unlimited?

I need to get rid of this annoying recording i get every time i dial a out going number.... " The time left for this call is unlimited"...
can i get some advice???
Anyone???

I just want to say....THANK YOU!!!! to all of those who responded to my
aid.
i DID fix the issue.. via the 888 294-6804... followed the
prompts..opitions 4... then opt. 2... then opt. 3... then opt. 1....then
opt. to Low. whaaala.
Again THANK YOU !!!
AWESOME>>>>
On Wed, Feb 11, 2015 at 6:30 AM, tikibar1 <[email protected]>

HT201401 I am unable to end a call and have tried everything to disconnect it. Has been running for 9 hours. How can I end this call?

I am unable to end a call and have tried everything to disconnect it. Has been running for over 9 hrs. I seem to be caught in a loop.
How can I end this call?

hold down the power botton on the top of the phone. Then slide to power off. wait to the count of 10 then hold down the power button again till the apple logo comes on.

How to remove "About this Page" and "Privacy Statement" on a OA page

Hi,
How do i remove "About this Page" and "Privacy Statement" links at the bottom of an OA page and add "Close Window" link on the top right corner of OA page.
Please help.
Advance thank
Pavan

Hi,
1. Select Personalize Page link at top right of page.
2. Select Choose context button.
3. In the scope drop down box select OA Footer.
4. Click on apply.
5. Expand privacy.
6. Click on personalize pencil icon.
7. Set Rendered property to false at required level.
8. Click on apply.
9. Click on Return to Application link.
thanx
Pratap

I have an ebookbrowse toolbar icon right next to my homescreen icon. I cannot figure out how to remove/uninstall this. Please advise.

I accidently visited the ebooks browse site, and apparently the site installed its own toolbar buddy in firefox. I cannot figure out how to remove it. Please help

Go to Firefox, Add ons then click to remove the ebook toolbar

How to remove messages data

My iPhone 4s is running low on starage space.
When I go to usage in the settings it says my messages is using 5gb of data storage.
My emails are empty as are my text messages.
How can I remove the data that the messages service is stroring?
Thanks.

Barbara222 wrote:
"What do you need a plug-in to do?"
To strip exif data and tags.
Sorry, I thought you were asking a follow-on question. It didn't make any sense that you would ask about a plug-in if you were already told how to do it in Photoshop.
Frankly, it doesn't make all that much sense to use Photoshop at all for the task.
Have a look at the freeware viewer called IrfanView. I believe it can be set to batch process a group of images, and save them back out without metadata.
-Noel

Can't make this call with Unlimited World trial?

Trying to make a call to Mexico with +52 and am seeing the insufficient credit message but I just got on the Unlimited World trial.

According to this forum: http://forum.lowyat.net/topic/2175165/all, it seems that Siri is expecting a 7-8 digit phone numbers excluding the country code and area code, so adding an extra "0" digit or two at the back of the phone number may be able to fix your problem. The phone number should still connect correctly. Try that, it works for me in Indonesia where some phone numbers are still 6 digits.
Hindra

How to remove messages from JMS Queue?how to configure queue in spring?

Hi
I have Confiured a JMS configaration in spring applicationConfiguaration.xml file
<bean id="connectionFactory" class="org.apache.activemq.ActiveMQConnectionFactory">
<property name="brokerURL" value="tcp://localhost:61616"/>
<property name="useAsyncSend" value="true"/>
</bean>
<bean id="queue" class="org.apache.activemq.command.ActiveMQQueue">
<constructor-arg value="foo"/>
</bean>
<bean id="broker" class="org.apache.activemq.xbean.BrokerFactoryBean">
<property name="config" value="classpath:activemq.xml" />
<property name="start" value="true" />

</bean>
<bean id="auditInterface"
class="org.springframework.jms.remoting.JmsInvokerProxyFactoryBean">
<property name="serviceInterface" value="com.infiniti.gpn.auditing.AuditInterface"/>
<property name="connectionFactory" ref="connectionFactory"/>
<property name="queue" ref="queue"/>
</bean>
<bean id="listenerContainer" class="org.springframework.jms.listener.SimpleMessageListenerContainer">
<property name="connectionFactory" ref="connectionFactory"/>
<property name="destination" ref="queue"/>
<property name="messageListener" ref="auditMessageListener"/>
</bean>
Sender is sedning messages continusly messages that messages r storing in queue , these r acupying more memory in RAM , due to that jboss is restarting for each request, is there any way to clean up messages in Queue ? if it is there then how will configure that queue in apllicationConfiguaration.xml file?
Thanks in advance
Nara

Hi,
Even i have a similar kind of requirement where in, i want to clear the JMS Queue Message programmatically, on certain condition.
i am using Spring JMS. The JMS Queue has a listener. In the listener we want to clear the Queue contents based upon the condition.
If anybody has any idea about this, please reply back.
Thanks in Advance.
Manjunath.

Error message on upgrade failure upon Firefox startup even though upgrade was successful. How to remove message?

I was upgrading Firefox through the About dropdown menu. I was unable to download successfully but later was able to download and install. Now everytime I open Firefox I get the message "The update could not be installed. Please make sure no other copies of Firefox are running and try again". I would like to get rid of this message as the update was successful. I am currently on v 9.0.1 with an XP os.

I totally agree, there have been many Mac users that have been effected by this.

Getting this message when trying to access our cameras, how to fix? This address is restricted This address uses a network port which is normally...

Just installed Firefox for my boss, and ran into something I've not seen before. When trying to access our private camera system, that uses specific ports, I got this message: "This address is restricted - This address uses a network port which is normally used for purposes other than Web browsing. Firefox has canceled the request for your protection."
Cannot find a setting in Firefox to correct this problem. Please help.

Hello,
Can you please check if either of these links help in the resolution of the issue
# [http://kb.mozillazine.org/Network.security.ports.banned.override Firefox ports override]
#[http://blog.christoffer.me/post/2012-02-20-how-to-remove-firefoxs-this-address-is-restricted/ Remove Firefox this address is restricted error]
Thank you

How do I escalate a call when tech support lose intere

-----Original Message-----
From:
Sent: 24 March 2005 7:6
To: 'CLE Customer Support'
Subject: FW: How long do you expect me to wait for a reply?
Do I have to go to trading standards to get you to honour this warranty? This is a disgrace - sort it out. This is extremely poor customer service and a breach of your warranty.
-----Original Message-----
From:
Sent: 22 March 2005 08:5
To: 'CLE Customer Support'
Subject: RE: CLE - Technical Support Request (KMM563096I2452L0KM)
How do I escalate this call? I have a card that is not working under warranty and you seem unwilling to answer my mails any more. I hate to be the bearer of bad news but you have to. This card must be fixed or replaced, and it would be nice if that happened sooner rather than later. Why am I doing all the chasing by the way, you're a big enough supplier to get this sort of thing right, aren't you?
Rob.
-----Original Message-----
From:
Sent: 7 March 2005 08:40
To: 'CLE Customer Support'
Subject: RE: CLE - Technical Support Request (KMM563096I2452L0KM)
Hello, it's me again, not heard from you for 5 days. Are you planning to reply? You have obligations of warranty which you are summarily failing to carry out here. Please sort this out!
Rob.
-----Original Message-----
From:
Sent: 3 March 2005 7:28
To: 'CLE Customer Support'
Subject: RE: CLE - Technical Support Request (KMM563096I2452L0KM)
Situation changed. Having restored settings to previous state after doing all the below, about a day later I now have no sound at all for no reason whatsoever. I have rebooted, re-checked all connections etc etc, sound has just disappeared in the middle of the day without changing anything. It was fine this morning and now it's completely silent and PC's been on all day. This card is definitely dead, what else would do that?!?!
Cheers,
Rob.
-----Original Message-----
From:
Sent: 2 March 2005 6:03
To: 'CLE Customer Support'
Subject: RE: CLE - Technical Support Request (KMM563096I2452L0KM)
Hi,
OK, I can't test on another PC as I don't have access to one, and I really dohope this is the last set of tests incidentally. It worked, then it stopped one day. A complete reformat and clean driver install didn't fix it. Re-seating the card didn't fix it. Seems pretty straight forward to me the card has failed, and I do need it replacing.
I have however done everything else below as requested. If I select CMSS, I get no output for rear-left/rear-right using channel test. If I select CMSS2, I get output from the front speakers for rear-left/rear-right channels, but nothing from the rear.
If I configure to 5. and enable CMSS I get output from jacks and 3 (orange & green)of the soundcard in the left headphone earpiece.
Hear from you soon,
Rob.
-----Original Message-----
From: CLE Customer Support [mailto:[email protected]]
Sent: 2 March 2005 03:7
Subject: RE: CLE - Technical Support Request (KMM563096I2452L0KM)
Dear Rob
Thanks for your reply
Please test the soundcard on another PC(With different motherboard) Ensure onboard soundcard is disabled.
Run creative diagnostic test, any problems?
Go to device manager, is there any problem with soundcard?
Configure the speaker setting as 5..
Please enable CMSS and play MP3.
Use a earphone and connect to line-out of soundcard.
Any sound?
Now please try on line-out3, any sound?
Please verify the correct jacks you are connecting..
CMSS is an option that allows you to play your audio to all 5. speakers even if you are not playing a true 5. encoded audio file. For example, if the sound is a stereo sound, it will duplicate the front channels, and send them to the rear channels. Then it will mix the left and right signals to create a center channel. Turning CMSS on basically simulates
5. audio.
TO TURN ON CMSS IN Mediasource
. Open MediaSource (Start, All Programs, Creative, Creative MediaSource, Creative MediaSource Organizer).
2. There should be an EAX button underneath the Record button at the bottom of the screen, towards the left. Beside this button, there should be a small ellipsis button (. . .) that you can press. Click on this.
3. Go to the CMSS 3D tab and check the box next to "Enable CMSS 3D"
4. Place a dot next to either CMSS or CMSS2. Whichever sounds better to you.
It is important to remember that if you do wish to play a 5. encoded file, you will need to turn CMSS off. Otherwise you might not receive each discreet channel.
Please retain all the previous correspondence when replying to this email.
Best Regards
Creative Customer Support Services
Creative Labs Europe
To provide feedback on your "Creative Experience" and our service please click on the following link:
http://www.**bleep**.com/support/con...asp?r=CLE&d=TS
Please do not use this link to submit technical queries
Original Message Follows:
Hi,
Tried all that and still no joy unfortunately. Everything ok except output from rear-left and rear-right.
Always disable onboard sound nad have just reformatted XP and reinatalled with drivers from creative website, so I know installation is not corrupt and up-to-date. I also had this problem before re-installation of XP, so suspect hardware rather than software failure.
Have removed all traces of card/drivers and tried again and moved PCI slots with same results.
Cheers,
Rob.
-----Original Message-----
From: CLE Customer Support [mailto:[email protected]]
Sent: 0 March 2005 03:37
Subject: RE: CLE - Technical Support Request (KMM5590925I2452L0KM)
Dear Rob
Thanks for your reply
Rear center is fine in speaker test...
Anyway if you have test the speaker with another device and no issue for rear channels, there is no problem with speaker system now...
Please insert the soundcard on another PCI slot, and make sure it is firmly inserted. Please disable any onboard sound card if available through BIOS.
Go to Control Panel, Add Remove Programs and un-install all listings related to your audio card. Do not restart your computer when prompted so.
Go to Control Panel, and switch to Classic View. Click System, Hardware tab, Device Manager button and delete all sound cards entries in Sound, Video and Game Controllers as well as any previous sound card entries from the Device Manager.
Reboot the computer and cancel out of any driver installation if you are prompted. Insert the Creative Sound Blaster installation CD into your CD-ROM dri've. Exit from the installation wizard if it autoruns.
Click Start, Run and then Browse. Browse to Z:\Audio\Drivers\CTZAPXX.EXE, where Z represents the CD Rom Dri've.
Choose YES if you receive a prompt "Overwrite existing shared creative audio driver files?"
Select Driver un-installation for WDM drivers and click OK.
When prompted to restart, say No.
Click Start, Run, type MSCONFIG and press Enter.
Check the box next to Selecti've Startup and deselect Load Startup Items.
Select the SERVICES tab and select Hide All Microsoft Services.
Uncheck all results and click OK.
Browse to the C:\Temp folder and C:\Windows\TEMP (if it exists) - all files and folders in the temp folder need to be either deleted or moved to a new folder.
Browse to Program Files, Creative and delete the Sound Blaster Folder - if you get a file that won't delete, right click on the file, click Properties and clear all the attributes. The file should then be able to be deleted.
Empty the Recycle Bin, and reboot the computer.
If you wish to reinstall your software & drivers, do this now. For more information on how to install your product, please visit the Product Guide page for installation instructions. Otherwise, go to the next step.
Click on Start, Run. Type MSCONFIG and press Enter.
Select Normal Startup, and press the OK button.
Reboot the computer
Run creative diagnostic test, any problems?
Configure the speaker setting as 5.
TEST CARD WITH HEADPHONES
. Run speaker test
2. Plug headphones into the front out jack 3. Click on the speaker test button 4. In the headphones you should hear a voice for front left, and front right.
5. Plug headphones into the rear out jack 6. Click on the speaker test button 7. In the headphones you should hear a voice for rear left and rear right.
8. Do you hear sound from each channel?
Any sound from rear channels?
Please retain all the previous correspondence when replying to this email.
Best Regards
Creative Customer Support Services
Creative Labs Europe
To provide feedback on your "Creative Experience" and our service please click on the following link:
http://www.**bleep**.com/support/con...asp?r=CLE&d=TS
Please do not use this link to submit technical queries
Original Message Follows:
Hi,
I have done the below, and get output via a walkman connected directly to the sub on both front and rear speakers no problems at all.
I have reconnected the cables from the sound card, run channel test again in speaker settings, and still get no output from rear-left and rear-right.
I should have mentioned before that rear-centre is fine.
Any further help will be greatly appreciated.
Cheers,
Rob.
-----Original Message-----
From: CLE Customer Support [mailto:[email protected]]
Sent: 09 March 2005 08:40
Subject: Re: CLE - Technical Support Request (KMM557969I2452L0KM)
Dear Rob
Thanks for contacting Creative Technical Support.
Please use an external cd player and connect to the front input on the subwoofer.
Play the CD, any sound?
Now try on the rear input.
Play the CD, any sound from the speakers?
Now please connect back the speakers to the PC.
Ensure you have connected properly.
Ensure you have configure 6. speaker setting, run a speaker test.
Any sound from rear channel?
Ensure the balance control is configure properly as well
Please retain all the previous correspondence when replying to this email.
Best Regards
Creative Customer Support Services
Creative Labs Europe
To provide feedback on your "Creative Experience" and our service please click on the following link:
http://www.**bleep**.com/support/con...asp?r=CLE&d=TS
Please do not use this link to submit technical queries
Original Message Follows:
=======================
Subject: CLE - Technical Support Request
Name:
E-mail Address:
Self Description:
ID(3) Advanced PC User
Country: United Kingdom
Support Inquiry: ID(3) My Creative hardware stopped functioning correctly
Product: Sound Blaster? Audigy? 2
Purchase Date: 4/3/2004
Serial Number:
Operating System: Windows XP
Creative Model Number: SB0240
Computer Brand/Model: self built
Processor/CPU: Athlon 3200+
Memory: 2xgb DDR400 Dimms
BIOS Type/Revision: Phoenix - rev 008
System Board/Chipset: ASUS A7N8X Deluxe rev2.0
Detailed Problem Description:
Typical, following months of trying to get a replacement remote control cable for my inspire 6. 6700 the 2 rear speakers on the set don't play sounds any more. I have done a clean XP install to ensure no driver corruption, but no difference. It's not the subwoofer as I have a spare, unused sub and that gives the same results.
I have also checked all cabling, mixer/volume settings and nothing unusual is showing.
Of course, my audigy 2 card is my guess as the culprit, I can't be positi've though. All other speakers operate perfectly, can even hear background hiss through the rear-left and rear-right speakers which won't play sounds/music/games or anything at all. But when I select "Creative Speaker Settings" to test the channels individually, they don't play a test sound here either.
Any help greatly appreciated.
Cheers,
Rob.
PS: Please remove the technical support advisor name when posting quote from the email.Message Edited by Jason-CL on 03-30-2005 06:7 AM

Hi qwerty,
Dun tink that creative customer support sucks cos I had been dealing with them in the past and I can say that their service are quite gd and fast. If you wanted a refund, I tink you need to contact the store that sells you the product. Dun tink creative will refund you though.

Delete/remove message

Hello comunity,
in a project (CRM2007) I need to search a product with the standard search help (see coding below).
The result is fine but the search help generate automatically an information message in the UI u201C1 object foundu201D.
Does anybody know how to remove/delete this message??
Thanks in advance.
DATA: lr_qs   TYPE REF TO cl_crm_bol_dquery_service,
      lr_result       TYPE REF TO if_bol_bo_col,
      lr_ent          TYPE REF TO cl_crm_bol_entity.
lr_qs =
cl_crm_bol_dquery_service=>get_instance( 'ProdAdvSearchRgIndObjects' ).
IF lr_qs IS NOT INITIAL.
    lr_qs->add_selection_param( iv_attr_name = 'PRODUCT_ID'
                                iv_sign      = 'I'
                               iv_option     = 'EQ'
                               iv_low        = lv_product_id
                               iv_high       = '' ).
ENDIF.
lr_result ?= lr_qs->get_query_result( ).
lr_ent ?= lr_result->get_first( ).
Edited by: Juergen Klein on Mar 13, 2009 11:26 AM

Hi Jürgen,
I just implemented my coding and it is working.
Get an instance of the message service.
Call the collect_messages( ) method with deletion flag set.
Then get all messages using get_messages().
Iterate over the internal table for your class ( COM_PRODUCT ), deleting where message is your desired ID ( 004 ).
Last call method add_bapi_messages( ) with the table you adjusted in the step before.
cheers Carsten

How to transfer Messages history from Mavericks to Yosemite clean install

I would like to do a clean install of Yosemite on my MacBook, but retain all of my Messages history and attachments from my current Mavericks install. Is this possible? What files do I need to copy from the Mavericks install (before I wipe the HD) and where do I need to put them after I install Yosemite (cleanly)? Anything else I need to do after copying them?
Thanks!

I managed to finally get mine to work, but not after a bit of trouble and losing new messages since my time machine back up (about a days worth since my backup replaced my current. I backed up and upgraded last night, and I figured out how to restore messages this morning, so anything in between that I got on my phone was lost. no big deal).
Much of the below is from other discussions, so I don't want to take credit for it, but wanted to make it easy for you, and there was one small change.
First make sure you can see hidden files by opening terminal and inputting: defaults write com.apple.finder AppleShowAllFiles YES
QUIT YOUR MESSAGES APP
Replace the following files from your backup to your current clean install. Pretty much all the files should be in the same spot, except for one folder that I'll explain further below.
Same File path
/users/<name>/Library/Messages-------> /users/<name>/Library/Messages/ this folder should include 4 files:
chat.db
chat.db-shm
chat.db-wal
the folder "Attachments"
/users/<name>/Library/Preferences----> /users/<name>/Library/Preferencescopy any file that includes iChat or Messages in the .plist
Different File pathI am not sure if this matters, but it's something I noticed when I got a message in my clean install before trying to restore my history. In Yosemite, I noticed that that "Attachments" and "Archive" folder are both in /users/<name>/Library/Messages, whereas in Mavericks, the "Attachments" folder is in that file path, but the "Archive" folder is located in /users/<name>Library/Containers/com.apple.iChat/Data/Library/iMessages/Archive, and within this same folder there is a shortcut to the Attachments folder. (I'm not sure if this matters, but this worked for me). I hope I didn't confuse you there!
/users/<name>/Library/Containers/com.apple.iChat/Data/Library/Messages/Archive-------> /users/<name>/Library/Messages/
Restart your computer
Open Messages and it will rebuild your database.
Ta da!

How to remove ABMultiValueCreateMutable warning

Hello all,
I am add label for emaiaddress,address,etc.It is work or Home label in iPhone simulator contacts.
I write
ABMutableMultiValueRef multiValue = ABMultiValueCreateMutable(kABHomeLabel);
It create label but,
It give me warnig:passing argument 1 of 'ABMultiValueCreateMutable' makes integer from pointer without a cast.
How to remove i this warninig?..
Thank you..

You can't store a CFStringRef in a NSMutableDictionary. Create a NSString from the CFStringRef and use the NSString. Try something like:
NSString *tmpKey = (NSString *)kABPersonAddressStreetKey;
[homeAddr setObject:@"xyz" forKey:tmpKey];
I think that will work. NSString is bridged to CFStringRef so this conversion works.
You might also be able to just do:
[homeaddr setObject:@"xyz" forKey:(NSString *)kABPersonAddressStreetKey];

"how to Remove message, this call is unlimited"

Similar Messages

Maybe you are looking for