How to Remove port number for SIP trunk in CME
Hi,
I trying to set a SIP trunk with SIP provider, I have CME 7.1
The trunk is registered now but I can´t make calsl via SIP provider. After some debbugs sip provider's staff told me that the solution is not
not append the port in the INVITE.
Is it possible to do this?, How?
I have found some info about normalization but is relating to CM server not CME.
regards
what port number does your provider use for signalling? They need to provide you the port number if its different from the standard 5060..
You can then configure the signalling ports on your dial-peer as shown in example below..where port 5081 is used here
dial-peer voice 1 voip
destination-pattern .T
session protocol sipv2
session target ipv4:10.10.10.24:5081
Please rate all useful posts
"opportunity is a haughty goddess who waste no time with those who are unprepared"
Similar Messages
-
10g express, how to change port number for the database home page
10g express uses port 8080 for its http listener. However this number has been used by Tomcat on my computer. How can I chang the port number for the 10g home page?
Regards
jlAndy, thank you very much, I have been able to changed the port number following your advice.
I hope you do not mind I ask a further questions along this line:
I installed 10 express db on 2 computers. One with Tomcat and the other without. Following your advice, I successfully changed the port number on the one without Tomcat.
On the one with Tomcat, I believe it was because I installed the 10g express while the Tomcat was running, I can neither go to the 10g's home page (page cannot be displyed), nor logon to the database from sqlplus (ora-12560: TNS:protocal error) even after I shut down the Tomcat. By checking with 'netstat -an', it is known that the http listerner is not listerning.
Can I change some configuration file to solve this problem? Or do I have to reinstall 10 ex? I prefer the 1st aproach of changing config file, even it is not as easy as reinstallation.
Thanks
jl -
How to remove leading zeros for an item number within quickviewer
how to remove leading zeros for an item number within quickviewer. Pls help
ask your abap guy to do it. not portal guys business.
-
How to change the port number for deployment in JAVA Studio Enterprise 8?
Hi!
Yesterday i downloaded this new sun java studio enterprise and found it mind blowing.
Now i find that all my previous applications which were running on port 8080 can't be run on sun java studio enterprise(sjse) 8.
Can anyone tell me how to change the port number on this software so i won't have to edit all my applications?http://docs.sun.com/source/819-0080/install.html
In the Admin Configuration page (or at the command line), enter the following:
Admin User Name�Name of the user who administers the server
Password�Admin user�s password to access the Admin Server (8-character minimum)
Admin Port�Administration port number for initial server instance
HTTP Port�Port number to access the default server instance
HTTPS Port�Secure port number to access the default server instance -
How do i find the port number for oracle10g
Hi,
I have installed oracle10g on my pc running windows XP. I need to get the port number for JDBC drivers used by Java Application when defining a JDBC source.
Java is running on the same machine.
When I installed oracle I was given the links (with port numbers) for EM, ULTRA SEARCH and iSQLPLUS, what I need is the ORACLE10g database port number. Anybody know where I get from ?
Cheersthanks for the reply the portlist does not contain the port of oracle. The file is below.
[i]Ultra Search HTTP port number =5620
Enterprise Manager Agent Port =
iSQL*Plus HTTP port number =5560
Enterprise Manager Console HTTP Port (oracle10) = 5500
Enterprise Manager Agent Port (oracle10) = 1830
However searching through some other threads found the port to be 1521, which
oracle must set during installation and tell anybody, unless this infor is in the log.
so configured the oracle JDBC driver as below (PE8.2 --> ConnectionPools)
Datasource Classname = oracle.jdbc.pool.OracleDataSource
URL = jdbc:oracle:thin:@localhost:1521:oracle10
User = abc
Password = abc
Now able to ping. Cheers -
Anyone know how I can remove the port of the URL, What do I need to configure to change the url and appears with another name?
I have a very similar question as well. I am very new to web applications and web development in general, but we have some here that will come up by simply typing in the IP of the host or the word associated with that host in our local DNS environment. You are then directed to whatever site is on port 80 of that host.
I would like to do the same with my app I have built in App Express - have users type in a "keyword" and they are immediately directed to my application home page. If my application URL requires a specified port 8080, this doesnt happen by simply pointing to the host. Is it as simple as changing the port number for the application? -
How to find port number , when there will be different instance number ?
In case of portal url,
port number is 50000 for default instance number 00.
how to find port number , when there will be different instance number , instead of 00?
ThanksHi
You can find the port number by your instance number as follows:
There is a general format for the port number like you have mentioned.
For 00 instance the port number is 50000.
The general format for the port number goes like this:
<b>5<instance_no>00</b>
If your <b>instance number is 01</b> then the port number would be <b>50100</b>.
It depends on the installation type which you perform.
You can also change the instance number during the installation but normally you dont do this.
If you have many components or units installed on your system you may have more than one instance in that case it may go like this 00, 01, 02....accordingly port number will be 50000, 50100, 50200...resp.
Hope this solves your doubt.
If you need some more clarification please lemme know.
Regards
Sumit Jain
**Rewrd with points if useful. -
Cca xml export for SIP Trunk service providers, request or schema.
Hi
Please can I have the complete xml schema for SIP trunks so I can create a proper template?
Exporting from CCA 3.2.2 gives me an incomplete and sometimes inaccurate xml file
example: toll fraud protection - I would like to add this in to the template - how
SIP registration: If I set this to 120 on CCA and export - the exported template remains as 3600
thanks
AdamHi Adam,
Are you saying when you try to export your SIP trunk settings via CCA that your settings are incorrect in the xml file? If so, I recommend opening a case to troubleshoot the issue as it sounds like a bug to me. -
Disable Canonical URL or Remove Port Number
Hi All,
We are using the publishing template of Sharepoint 2013 . This generates the canonical url as shown
<link rel="canonical" href="http://www.somesite:80/Pages/default.aspx" />
I want to achieve removal of port number from the above link.
If not posssible to either remove the entire link itself
Thanks
ThomsonHi Thomson,
It is by design that the canonical URL will display port number for SharePoint pages.
And if you have other sites which are using port number other than 80, then the port should be displayed in the URL for requests can be directed to the correct sites.
So the port number should not be removed from the URL.
If you do not want this canonical URL, then you may need to disable the Search Engine Optimization feature in the site collection.
As this feature is enabled by SharePoint Publishing feature, then we need to disabled it using PowerShell command:
Disable-SPFeature -identity 17415b1d-5339-42f9-a10b-3fef756b84d1 -URL
http://sitecollectionURL
Best regards.
Thanks
Victoria Xia
TechNet Community Support -
Change default port number for web logic!
Hi folks,
In my scenario, i already installed obiee 11g with simple install along with web logic on windows xp machine.where this will creates default port number for all services. now i want to change default port number of web logic that is 7001 to some to other port number. how to change this ??.plss help me asap.
regards,
maheshRefer tohttp://www.oracle.com/technology/documentation/1012_solaris/install.1012/install/ports.htm
-
How to remove srial number profile ?
Hi sap Guru,
my issue is how to remove serial Number profile in material master,
a material use all plant ,only one plant serial number profile is on,
ex- having plant 1000,2000,3000,4000,5000,6000.
plant 6000 serial number profile is on, having five quantity with serial no and the material already issue,
how to remove serial number profile 6000 plant that material ,
i try in material master remove serial no profile but getting error serial number profile already assign
How to remove serial no profile For plant 6000 ?
2.
in sto material sent delhi to bagalore ,
available material is 10 in delhi store , when user sto that material geting error like
only 0 ea of material available
what might be problem ?
regards
shivHI Shi,
1) Material serial number removed procedure as follows.
Using T-Code MM02-change material code to the respective plant(6000),storage location,sales org and then give input data to the material view screen basic data1, basic data2...... In the view Plant data / Stor.2 input screen General plant parameters options Serial no.profile - '0001', SerLevel - '1' data to be removed during change/edit of the material. After that doing MIGO for the material serial number should not asked and also not displayed.
Hope, it is useful for you.
Regards,
K.Rajendran. -
Change WOL Port number for clients
Hi All
We want to implement in our environment WOL functionality , for WSUS deployment and scheduled OSD deployments
We cannot unfortunately implement the default UDP port 9
My question is how can we change that default port on the clients?
I know that we can change the port on the primary server -> Site configuration -> Sites -> Properties primary site server -> tab
Port and here we can change the port number of Wake on Lan
For the client I noticed that there is a client setting -> Power Management -> Wake on Lan port Number (UDP) but that number is grayed out and set to 9
Also when I create a custom Client Setting that port number is grayed out and set to 9
How can I change that port number for the client?
Thx in advance
Regards,
JohanThe port number in Client Settings/Power Management is grayed out because "Enable wake-up proxy" is disabled. When you enable it, it becomes available. Be aware that wake-up proxy and wake on lan is 2 different things. (Beware mac address flapping)
To change the Wake On Lan port go to, primary server -> Site configuration -> Sites -> Properties
primary site server -> tab Port.
Wake On LAN port number (UDP)
For System Center 2012 Configuration Manager SP1 and System Center 2012 R2 Configuration Manager only:
Keep the default value of 9, unless you have changed the Wake On LAN (UDP) port number in the site Properties, Ports tab.
Important
This number must match the number in the site Properties. If you change this number in one place, it does not automatically update in the other place.
Benoit Lecours | Blog: System Center Dudes -
What port number for Desktop Sharing using in Lync Server 2013 and Lync Online
Dear All,
My environment using Lync Server 2013 and Lync online on Office 365. I don't want my user using Desktop Sharing feature. then I need to know what port number for Desktop Sharing using in Lync Server 2013 and Lync Online.
I will deny this port on personal firewall each client.
Thank you for your advise.Hi,
I'm not sure you'd be able to do this with ports without impacting other application sharing features such as Q&A, Whiteboard, Poll etc - I'm pretty sure they all come under the same umbrella of ClientAppSharing.
Ordinarily you would create or modify your conferencing policy to restrict sharing to single programs only using a cmdlet similar to below;
Set-CsConferencingPolicy -Identity "Global" -EnableAppDesktopSharing SingleApplication
This would disable desktop sharing but enable users to continue sharing other single programs. If you want to remove that functionality too, then replace the 'SingleApplication' parameter with 'None'. Then users won't be able to share any programs either.
This is the correct way to do it as the icons will be greyed out for the users. Doing it your way, they would still be able to click them, and it would throw an error - this will lead to a lot more support calls and people assuming a service is broken.
I hope that helps some.
Kind regards
Ben -
HT3396 how to buy serial number for iwork
how to buy serial number for iwork
I'm sure the problem is that you have the trial of iWork '09 installed. It's a "giitch" in the installer code that Apple has not fixed. You need to delete the trial & then reinstall from the boxed DVD or the Mac App Store. The files to delete are the iWork ’09 folder from the main HD > Applications; the iWork ’09 folder in HD > Library > Application Support & the individual iWork application plist files found in HD > Users > (your account) > Library > Preferences for each user.
Yvan Koenig has written an AppleScript that removes the files. You can find it on his box.com account in for_iWork'09 > other_iWork'09 items > uninstall iWork '09.zip. -
How to find serial Number for BCC Plugin?
Hi,
How to find serial number for Bcc plugin on FCP?
I need format my Mac so before that I to find the serial number?
Please anyone can help me....The serial number has the format like E-111-aaa-222-bbb-333-ccc-444-ddd-5ee-ffff, it can be found on a piece of paper which has 3 stickers with it inside the box.
Maybe you are looking for
-
I have a template that I am able to plug different pictures into at different times. The problem is that when I plug an image into that template, I find that the image is either too big or too small. Is there a way to plug the image into the templa
-
Error while creating SAPJSF user
Hi all, I am receiving following error despite manually creating sapjsf user in client 800. This is the trace from dev_usercheck. Aug 31, 2010 6:05:16 AM ...eck.main() Path: Entering method Aug 31, 2010 6:05:16 AM ...eck.main() Debug: Version: $I
-
HT1657 Im having trouble downloading my rental on my apple tv.
Im having trouble downlading my rental on my apple tv.
-
Outlook delete attachment files if use POP3
Hi every body, I have a problem with outlook. I send a mail with attachment using java mail api. Anyone get the mail correctly (gmail, outlook, outlook express or thunderbird) via SMTP. But if outlook try to get the mail via POP3, it deletes attachme
-
Within the first month of my having an n91 I was experiencing problems with the phone. It just hangs daily and does not allow you to even restart the phone without removing the battery. I thought it was a software problem so I had the firmware upgrad