How to replace the installed Generic USB Hub to Generic Super Speed 3.0 USB Hub?

Hi I have a problem with my RMBP 15" USB PORTS (both are 3.0 physically). Most of the days I will use windows 7 home premium through bootcamp.
When I connect my WD My Passport 3.0 to the usb port, there will always a pop up saying "Your device can work faster if it connects to a Super Speed 3.0 USB Port and when I do file tranferring between these 2 devices I will only get an average speed of 30 mb/sec which is DEFINITELY a speed of usb 2.0. As the usb 3.0 will be able to transfer (in reality) up to 100 mb/sec.
I think there is something wrong with the drivers installed. Attached is my device manager showing all the USB drivers installed.
Please advise me on what should I uninstall and install and where can I download the drivers or firmware.
For additional information, my macbook in using Intel Chipset C216.

This is more for googlers/random people in the same boat, since the OP may not be checking this any more.
I have arrived at this thread from another angle: I downloaded 'SlimDrivers', a free and non-contaminated 'driver updater' Windows program which is heavily-reviewed, on CNET as actually GOOD as opposed to almost all other 'dodgy' driver update checker programs out there (like Driver Reviver, Device Doctor, and Driver Detective - not to mention the scammy and notorious DriverAgent, of course).
I hit scan, and a whole set of drivers - seemingly under the one chipset download (as assisted by this youtube run-through) - came up. It's extremely user friendly and downloads the installer for you right from within the app. I've yet to install the chipset driver and restart - fingers crossed - but I think it's the same driver as OP is talking about.
Cos I've also noticed, at least once, some sort of USB issue in the past which made me think "huh, USB 3.0 mustn't be working with the bootcamp driver eh?"
So *I'm* wondering, whether what I've stumbled upon is indeed the same matter as OP, and thus also, maybe is a solution to the OP question as well .

Similar Messages

Qosmio G50-10J: How to replace the Optical Disc Drive (ODD)?

Hello there,
the optical drive of my Qosmio G 50 is not working properly anymore, it reads only some movie-DVDs, but sadly no videogameDVDs at all, so I cannot instal any games.
The warranty has already expired too. So I wanted to ask if it is possible to change the drive myself, if it is then how should I do it, and if by doing it would the laptop be in
serious risk of getting damaged?
I would be very thankful for every tip and every help you guys can give me!!!
Best regards,
a.z.

Hi
In different cases the ODD replacement is not very tricky.
If you want you can check this forum category.
Here you can find some videos how to replace the ODD on different notebook models:
http://forums.computers.toshiba-europe.com/forums/forum.jspa?forumID=115
Here is also a nice Youtube channel which provides the instructions how to replace the ODD:
http://www.youtube.com/user/toshibaeuropesupport
But maybe the ODD laser lens is dirty. In my case I could solve similar issue cleaning the laser lens using a cotton-wool tip and alcohol.
But be careful doing this!

How to replace the root tag in ABAP Mapping

how to replace the root tag with the certain string in ABAP Mapping
just like
<?xml version="1.0" encoding="UTF-8"?>
<root>
<name>Lawrence</name>
</root>
into
<?xml version="1.0" encoding="UTF-8"?>
<myRootElement>
<name>Lawrence</name>
</myRootElement>
i don't want to implement it in message mapping
please give me the sample code
thanks in advance

Use below code
odocument = ixmlfactory->create_document( ).
msgtype = odocument->create_simple_element(
name = 'myRootElement'
parent = odocument ).
Thanks
Praveen

Satallite A100: How to replace the keycaps?

Is there a manual on how to replace the keycaps after they come off?
My Satallite A100, one year old, lost two keycaps a few weeks ago, and I am unable to replace them, although I have all the (little) parts. It got even worse when some more came loose recently when my little son peeled some off, using the room created by the already missing keycaps.
Thanks!

Hello Mike
Reading your posting I can not understand exactly what is wrong with your keyboard but removing and putting in place keycaps (plastic with written symbol) is not problematic. You must just put it right in place and gently press it down. You will hear click and the keycap will be in the place again.
Under this keycap is placed small plastic mechanism. It contains two small plastic parts. If they are removed from the bottom you can put them inside again. To see how it looks like remove keycap from any other key and see how is it placed.
I have done the same now and with a little bit patience you can put it in the right position again.

How to replace the certificate of Cisco 2106 wireless LAN controller for CAPWAP ?

I have interested in CAPWAP feature and I download the open capwap project to make Access Controller (AC) and Wireless Terminal Point (WTP). I had built the AC which used PC and WTP which used Atheros AP. The CAPWAP feature work well when I enabled the CAPWAP that used my own AC and WTP. When I got the Cisco 2106 wireless LAN controller (Cisco WLC), I configured the Cisco WLC to instead my own AC but I got the authorize fail in Cisco WLC side. It seem the Cisco WLC could not recognize the CAPWAP message which sent form my own WTP. I think this issue just need to synchronize the certificate between Cisco WLC and WTP.So I need to replace the Cisco WLC's certificate manually. Does anyone know how to replace the certificate manually with Cisco WLC ?
Best Regards,
Alan

Unfortunately this Support Community is for Cisco Small Business & Small Business Pro product offerings. The WLC2106 is a traditional Cisco product. You can find this type of support on the Cisco NetPro Forum for all traditional Cisco products.
Best Regards,
Glenn

How to identify the installed Weblogic Server and JDK are 32bit or 64bit?

Hi everyone,
I have a question ~
Both Weblogic Server and JAVA JDK are installed on the server already, but I only know the Weblogic Server is 10.3.4.0 and JAVA JDK version is 1.6.0_25.
I know the 64bit Weblogic Server installation file is a wlsXXXX_generic.jar package and 64bit JAVA JDK needed also.
But, since the Weblogic installed already, there are no such installation files on the Linux Server now.
I have tried the "java -version" for java version and check the Weblogic version from Weblogic console.
How to identify the installed Weblogic Server and JDK are 32bit or 64bit with Linux command? Or is there any way to check it?

What you can try to do is use WLST (or an MBean browser, such as JConsole or JRockit Mission Control) and connect to the adminserver.
For example when using WLST:
# set the environment by using setWLSEnv.sh (located in the ${WL_HOME}/server/bin directory).
# start WLST by using: java weblogic.WLST
# connect to the adminserver
connect('adminusername','adminpassword');
# change to the serverruntime environment
serverRuntime();
# show the attributes
ls();
# Here an attribute is shown called WebLogicVersion that shows the version of WebLogic
-r-- WeblogicVersion WebLogic Server 10.3.5.0 Fri Apr 1 20:20:06 PDT 2011 1398638
# Note that this does not show if is 32 bits or 64 bits to retrieve this information you have obtain the JVM version
# change the directory
cd('JVMRuntime/AdminServer');
# show the attributes
ls();
-r-- Version R28.0.1-21-133393-1.6.0_20-20100512-2126-linux-x86_64
# when you have something like x86 at the you are running a 32 bit version, if you have something like x86_64 you are running a 64 bits versionAs mentioned above you can also retrieve this information by using a MBean browser.

Just purchased Lion...how long for the install wirelessly?

Just purchased Lion...how long for the install wirelessly?

Yes, the installer will launch automatically and wait for you when you wake up to proceed with the Lion installation.
Good Luck, and remember to back up your data always before installing operating systems or OS patches.

How to replace the char values into numeric in my string?

Hi Friends,
I would like to Replace the Charecter values with numeric value in my string.
Exp : first in my string I am having the value like this : 'ABCD1234' ( may be any char and num values ), and I want too get it by '99991234'.
I mean How to replace the char values into numeric in my string?
Thanks,
Sridhar

Hi Sridhar,
I would like to Replace the Charecter values with numeric value in my string.
Exp : first in my string I am having the value like this : 'ABCD1234' ( may be any char and num values ), and I want too get it by '99991234'.
So, if i understand you correctly, you want to replace all characters in a string with 9 as in the above example, irrespective of position of the character, if so try with the below code.
DATA: l_str TYPE string.
l_str = 'ASKHSIUDNSBDKJSDH124312431243124saasdfsf'.
REPLACE ALL OCCURRENCES OF REGEX '\D' IN l_str WITH '9'.
IF sy-subrc EQ 0.
WRITE: l_str. "Result will be 9999999999999999912431243124312499999999
ENDIF.
Regards,
Chen
Edited by: Chen K V on Jun 13, 2011 12:36 PM

Hp 7 voice tab screen broken unfortunately. tab is under warrenty.. how to replace the screen

hp 7 voice tab screen broken unfortunately. tab is under warrenty.. how to replace the screen

Hp india have bad service ever. I hv order three notebooks ' hp 15-ac026tx' before five days for firm. Distributior open the boxes. But at the time of installation not single driver supporting to 2gb graphics card. As distributor made with Hp support they replied the engineer will come to ur place soon. But still no one has come. And im going to cancel this order and will prefer other compony.

How to find the installed CUCM iso is restricted or unrestricted?

How to find the installed software in CUCM9.1(iso) is restricted or unrestricted??

Hi,
what u can do is u can login into OS administration through Putty . u get the details of VMWare .
Same can be compared and checked with OVA templates in README file
http://www.cisco.com/web/software/283088407/97505/cucm_9.1_vmv8_v1.7.ova.README1.txt
CUCM 7500 user node:
     Cisco Unified Communications Manager (CUCM) configuration that
     supports up to 7500 users per node.
     Details:
     Red Hat Enterprise Linux 5 (32-bit)
     CPU: 2 vCPU with 3600 MHz reservation
     Memory: 6 GB with 6 GB reservation
     Disk: 1 - 110 GB disk with pre-aligned disk partitions
you can see UNRST in attached snapshot.
regds,
aman

How to replace the virtual system as the real system in the TMS?

Hi,
I have a standard 3 systems TMS, which is 1 development system (real system, transport domain) and 2 virtual system(QAS and PRD).
And now, I will install the QAS system and replace the virtual system as the real one, How can I do in TMS?
I should delete the old TMS and rebuild the TMS with 1 DEV, 1 QAS and 1 virtual PRD? or just replace the QAS as the real one? What the operation should I do in t-code:STMS?
Many thanks.
BR,
Randy

Hi,
Do it as follows.
1. Remove transport routes (i think it is not mandatory)
2. Remove your Virtual system that you want to replace with physical system
3. Include the Physical system into Domain and accept it from Domain Controller
4. Configure the transport routes.You can see all the transports that were in the import queue of virtual system are now in the import queue of the Physical system that you added.
Only condition is, both Virtual System and Physical System should have same SID.
All the above will be done through STMS
Thanks,
Giri

Need guide on how - remove/replace the hard drive in my dv6t-6100, manual on hp shows different dv6

i am trying to remove and replace my hard drive on my dv6t-6100 beats edition laptop, every where i look on the internet and manual on hp for my model shows how to remove hard drive on a different dv6 than i have, which show a rectangle coverwhere the drive is with screw to remove hard drive cover, i dont have that on the bottom of my laptop. Please help
Another problem I have is my screen flickers a lot from time to time like something is loose, can i do something to fix that.
Thank you so much in advance

Here a repair site for the MacBook http://www.ifixit.com/Device/MacBook_Unibody_Model_A1342
For a hard drive try Newegg.com http://www.newegg.com/Store/SubCategory.aspx?SubCategory=380&name=Laptop-Hard-Dr ives&Order=PRICE
Or OWC http://eshop.macsales.com/shop/hard-drives/2.5-Notebook/
Here are video instructions on replacing the hard drive on the White Unibody http://eshop.macsales.com/installvideos/macbook_13_09_unibody_hd/
To transfer your current hard drive I like the free application Carbon Copy Cloner. It makes a bootable copy of everything on your hard drive http://www.bombich.com/index.html You'll need a cheap SATA external hard drive case. Put the new drive in the case then partition and format the new drive and clone your old drive to the new one. Check that it's set up right by booting up from the external drive. Then replace your old hard drive with the new one.
Here's a cheap SATA external hard drive case on Amazon. http://www.amazon.com/Vantec-NexStar-2-5-Inch-External-Enclosure/dp/B002JQNXZC/r ef=sr_1_1?ie=UTF8&qid=1332118549&sr=8-1
You can get a new third party power adapter on eBay for about $20
http://www.ebay.com/sch/i.html?_nkw=macbook+power+adapter&_sacat=0&_sop=12&_dmpt =Apple_Laptops&_odkw=macbook+power+adapter&_osacat=111422&_trksid=p3286.c0.m270. l1313
You can order a Snow Leopard 10.6 install disk for $29 as long as you have at least 1gb of RAM and 5gb of free space on your hard drive. http://store.apple.com/us/product/MC573Z/A?mco=MTY3ODQ5OTY
A 10.5 Leopard disk will run you around $200
To upgrade your iLife and iWork. If you only want iPhoto or other single apps from iLife '11 you can get them from the App Store after you've upgraded to 10.6.6. iPhoto, iMovie or Garage Band for $15 each and Pages, Keynote or Numbers from iWork '09 for $20 each.

How to replace the icon in the title bar and minimized window

I am not sure if this is a Swing question. But since nobody answered it in the Java Programming forum, let me place it here:
I would like to set my own icon in the title bar and in the minimized window of my java application, replacing the java coffee cup icon.
I am using:
frame.setIconImage(new ImageIcon("image.gif").getImage())
as was suggested previously in the Java Programming forum at:
http://forum.java.sun.com/thread.jspa?forumID=31&threadID=5212059
This does create the icon in both places. However, it only works when I run the program from JBuilder 2006. It doesn't work if I run the program from the .jar or the .exe file.
How can I make it work for my .jar and .exe file?
Please help! Thanks!

It doesn't work if I run the program from the .jar...working example for a .jar
import javax.swing.*;
import java.awt.*;
class Testing
public void buildGUI()
    JFrame f = new JFrame();
    Image img;
    try
      java.net.URL url = new java.net.URL(getClass().getResource("Save.gif"), "Save.gif");//correct capitalization required
      if (url != null)
        img = javax.imageio.ImageIO.read(url);
        f.setIconImage(img);
    catch(Exception e){}//do nothing - default will display
    f.setSize(200,200);
    f.setLocationRelativeTo(null);
    f.setDefaultCloseOperation(JFrame.EXIT_ON_CLOSE);
    f.setVisible(true);
public static void main(String[] args)
    SwingUtilities.invokeLater(new Runnable(){
      public void run(){
        new Testing().buildGUI();
}

How to replace the string in a file

Hi, I have a file which contains the following data
File.dat
<file>
<filenum>
W10
</filenum>
<hello>Heading </hello>
</file>
I need to replace the contents of file.dat
database sequence value (for example xx_seq.nextval)
Can some one please tell me how to search this <filenum>
W10</filenum>
and replace this with xx_seq.nextval
and write the entire contents of the file to new file
I am doing some thing like this
suppose if my database value returns 11 from the above sequence then
the output should be in file2.dat as
<file>
<filenum>
11</filenum>
<hello>Heading </hello>
</file>
declare f_in utl_file.file_type;
s_in varchar2(10000);
string1 varchar2(32000);
x number;
begin
f_in := utl_file.fopen('SAMPLEDIR','input.txt','R');
f_in1 := utl_file.fopen('SAMPLEDIR','input1.txt','W');
select xx_seq.nextval into x from dual;
loop
begin utl_file.get_line(f_in,s_in);
EXCEPTION
WHEN NO_DATA_FOUND THEN
EXIT;
string1:= string1 || s_in;
utl_file.put_line( (f_in1,s_in);
end;
end loop;
utl_file.fclose(f_in);
end;
In this case it is reading and writing as it is, but unable to replace the sequence value
Can some one please tell me how to do using replace function
Thanks

Hi, I have tried this but getting error
step 1: create table test_dept(dno number, dname varchar2(20))
insert into test_dept values(10,'10-Sourcing dept');
insert into test_dept values(20,'20-Audting dept');
insert into test_dept values(30,'30-Computer dept');
select * from test_dept;
DNO DNaME
10     10-Sourcing dept
30     30-Computer dept
20     20-Audting dept
step 2:
create table test_web (name varchar2(60), xml_col xmltype) ;
step 3:
create sequence test1_seq start with 100 increment by 1
step 4:
test.out has the following contents (it is not .xml file) and i dont have <?xml version="1.0" ?> tag at the begining
<File>
<File_Type>Type1</File_Type>
<File_Header_Record>
<file_num>WP10</file_num>
</File_Header_Record>
<Transaction>
<Transaction_Type>TR 1</Transaction_Type>
<Amount>
<Amounts>100</Amounts>
</Amount>
<Depts>
<Dept_Type>Sourcing</Dept_Type>
<Dept>10</Dept>
</Depts>
</Transaction>
<Transaction>
<Transaction_Type>TR 2</Transaction_Type>
<Amount>
<Amounts>200</Amounts>
</Amount>
<Depts>
<Dept_Type>Auditing</Dept_Type>
<Dept>20</Dept>
</Depts>
</Transaction>
<Transaction>
<Transaction_Type>TR 3</Transaction_Type>
<Amount>
<Amounts>300</Amounts>
</Amount>
<Depts>
<Dept_Type>Computer</Dept_Type>
<Dept>30</Dept>
</Depts>
</Transaction>
</File>
step 5:
DECLARE
v_check_file_exist BOOLEAN;
v_file_length NUMBER;
v_block_size NUMBER;
v_file_path VARCHAR2 (100);
v_file_name VARCHAR2 (100);
v_file_type UTL_FILE.FILE_TYPE;
v_str varchar2 (32760);
v_cnt number;
v_seq number;
--check whether file exists and has data in it
BEGIN
v_file_path := '/usr/tmp';
v_file_name := 'test.xml.out';
-- initailise the variables
v_cnt := 0;
UTL_FILE.FGETATTR (v_file_path,
v_file_name,
v_check_file_exist,
v_file_length,
v_block_size);
if v_check_file_exist
then
DBMS_OUTPUT.put_line (' File exists');
IF v_file_length > 0 AND v_block_size > 0
THEN
BEGIN
select test1_seq.nextval into v_seq from dual;
insert into test_web values(v_seq,v_file_name);
EXCEPTION
WHEN NO_DATA_FOUND
THEN
DBMS_OUTPUT.put_line ('No data found '||SQLERRM);
WHEN OTHERS
THEN
DBMS_OUTPUT.put_line ('others '||SQLERRM);
END;
commit;
ELSE
DBMS_OUTPUT.put_line ('No Data in File');
END IF;
ELSE
DBMS_OUTPUT.put_line (' File Not Available');
END IF;
END;
I am getting below error
File exists
others ORA-31011: XML parsing failed
ORA-19202: Error occurred in XML
processing
LPX-00210: expected '<' instead of 't'
Error at line 1
My requirement is to replace the
1. contents of the file WP10 from <file_num>WP10</file_num>
with sequence value 'WP101' because sequence is starting at 100
2. Replace all Dept tag <Dept>30</Dept> with Dname value from test_dept table
for example
<Dept>10</Dept> should be replaced with <Dept>10-Sourcing dept</Dept>
update the
when i say select * from test_web;
It should contain this row
101 <File>
<File_Type>Type1</File_Type>
<File_Header_Record>
<file_num>WP101</file_num>
</File_Header_Record>
<Transaction>
<Transaction_Type>TR 1</Transaction_Type>
<Amount>
<Amounts>100</Amounts>
</Amount>
<Depts>
<Dept_Type>Sourcing</Dept_Type>
<Dept>10-Sourcing dept</Dept>
</Depts>
</Transaction>
<Transaction>
<Transaction_Type>TR 2</Transaction_Type>
<Amount>
<Amounts>200</Amounts>
</Amount>
<Depts>
<Dept_Type>Auditing</Dept_Type>
<Dept>20-Audting dept</Dept>
</Depts>
</Transaction>
<Transaction>
<Transaction_Type>TR 3</Transaction_Type>
<Amount>
<Amounts>300</Amounts>
</Amount>
<Depts>
<Dept_Type>Computer</Dept_Type>
<Dept>30-Computer dept</Dept>
</Depts>
</Transaction>
</File>
Can you please check
Thanks

How to replace the hard drive on a Powerbook?

The 80 GB Toshiba HD on my Powerbook G4 17 inch recently failed. Apple informs me that the flat rate to replace the drive out of warranty is over $900. I can't see shelling out that much for a new drive on a two year old PB. I'd like to think I could do this myself. Are there instructions anywhere or do I just go about this in a logical, careful, methodical way - labeling screws and photographing progress, etc.?
Powerbook G4 80 GB Mac OS X (10.3.9)

That price is high. A 160GB hard drive like the one i installed in my 1 GHz PB 17 can be had from:
http://www.newegg.com/product/Product.asp?Item=N82E16822148073&CMP=OTC-Froogle&A TT=SeagateMomentus+5400.3+ST9160821A+160GB+5400+RPM+Notebook+HardDrive
for $205.
I installed my own, but installation should not cost more than. about $100.

How to replace the installed Generic USB Hub to Generic Super Speed 3.0 USB Hub?

Similar Messages

Maybe you are looking for