How to reset Dot11Radio interface via SNMP

Hi guys,
Please tell me how i RESET my AP's radio interface via SNMP? It's mean down and up right behind sb.
I'm using several SNMP commands for manage to our Cisco's. But I'm unsuccessful at this.. Please help me. Thakns.

Isn't there any response? isn't there any Cisco Specialist at there???

Similar Messages

  • How to restart base station via SNMP ?

    How to restart airport extreme via SNMP, with snmpwalk for example ? I can get a lot of information from base station with snmpwalk and airport-mib but still mystery what to poke when I want reboot base station over network.

    You are likely forgetting a step.
    Open AirPort Utility
    Click on the Time Capsule icon
    Click Edit in the small window that appears
    Now click the Base Station menu.....top of the screen....not the Base Station "tab" in the center of the screen
    Click Restart

  • Shutdown wireless interface via SNMP Write?

    Hi
    We're working on writing a very simple web app to control a couple of access points via SNMP.  I'm trying to shutdown the Wireless interface via SNMP WRITE with the following oid;
    .1.3.6.1.2.1.2.2.1.7.1
    and
    .1.3.6.1.2.1.2.2.1.7.2
    But its saying the integer of '0' is invalid (badValue, wrong type or length).  I'm able to set other values like hostname, etc, so I know my string is correct...can anyone help?  THanks
    Jason

    Hi
    Just found my own answer...the value to shutdown the interface is not 0, it's 2.  durrr
    Thanks
    J

  • Reporting bit/second sent and recieved on a switch interface via SNMP/SYSLOG

    Hi.
    In a Catalyst switch, under the command: show interface fast 1/0/1 (for example) there is a parameter "5 minute input rate YY bits/sec".
    Is it possible to send this value to a SNMP server or to a SYSLOG server? 
    Danny.

    here are 2 good basic documents on this topic:
    "How To Calculate Bandwidth Utilization Using SNMP"
    SNMP Counters: Frequently Asked Questions
    Basicly, what you have to do is, to poll the ifHCInOctets and ifHCOutOctets (from the IF-MIB (ifXTable) - e.g ifHCInOctets = .1.3.6.1.2.1.31.1.1.1.6.)
    and do some calculation to get bps. This thread gives a good example.
    there are 2 Mib objects, which gives directly what you want, but they are deprecated and have 32-bit counters, so they are not of practical use for highspeed (Gig) interfaces:
        locIfInBitsSec      1.3.6.1.4.1.9.2.2.1.1.6
        locIfOutBitsSec     1.3.6.1.4.1.9.2.2.1.1.8
    Typically you will poll these values with snmp instead of sending them; (for 64-bi counters (ifHCInOctets) you 'll have to use snmpv2c or snmpv3)

  • How to reset frontendHTTPPort value via wlst?

    I have set the FrontendHTTPPort value as 80 (even though I didn't have any LBR setup)... now whenever I tried to access the /console via the regular port 7001 (host:7001/cosnole), it takes me to the host:80/console and fails. Since I can't login to the console, I would like to remove the value for both the host and port for the frontend settings through command line or wlst etc.. pl. let me know a way to modify these values. Where is this value stored in the file system?

    Hi,
    It quite simple!!!!
    take current config.xml file as backup and remove front end host , port from there and clear cache and tmp on every server and then restart your admin server it will work fine for you.
    Regards,
    Kal

  • How to discover lwapp hostname via snmp virtual WLC

    Hi there,
    we recently installed a virtual WLC and configured some LWAPP access points. I want to monitor the status of the WLC and also of the access points. Using the airespace mib or lwap-ap mib I can monitor operational status and the number of associated clients. The only problem I have at the moment is that I can't recover the hostname, mac address or ip address to identify the access point. Does anybody knows which mib or oid to use to identify the access point?

    Hi there,
    we recently installed a virtual WLC and configured some LWAPP access points. I want to monitor the status of the WLC and also of the access points. Using the airespace mib or lwap-ap mib I can monitor operational status and the number of associated clients. The only problem I have at the moment is that I can't recover the hostname, mac address or ip address to identify the access point. Does anybody knows which mib or oid to use to identify the access point?

  • How to reset local admin user password in

    Dear members,
    i want to reset local admin account(not administrator built-in), let say i have user adminlocal and member in administrator group. my question, how to reset this user via GPO in domain, because i have more than 5000 workstation in my environment. and how to
    generate summary of all workstation which are password reset.
    i've tried from this link,
    http://community.spiceworks.com/how_to/show/1966-how-to-change-local-user-or-admin-passwords-on-remote-computers
    using PSTools sysinternal from microsoft, but while i execute one PC on domain for sample using this script, they showing access denied
    anyone in this forum can help me to resolve this problem?.

    Dear,
    you can use Powershell to do this.
    I've found a script in the script center which can do this.
    http://gallery.technet.microsoft.com/scriptcenter/66a5b38f-cdf1-4126-aa0c-be65e16dd650/view/Discussions#content
    Set-Password -computer 'server' -user 'Administratorlocal' 
    You can create a loop in powershell to check all your servers which you've posted in a .txt file for example.
    $strcomputers = Get-Content c:\servers.txt
    foreach ($strcomputer in $strcomputers)
    $admin=[adsi]("WinNT://" + $strComputer + "/administratorlocal, user")
    $admin.psbase.invoke("SetPassword", "Whatever1")

  • Interface errors (crc, in/output, collisions etc.) via snmp

    Hi,
    I'm trying to understand how to get interface errors via SNMP.  I do get stats via SNMP for ifInErrors / ifOutErrors etc, but I'm trying to get output via SNMP for the errors visible via the 'sh int x' command - CRC errors, input / output errors, collisions, runts. giants etc.).
    1) The SNMP ifInError / ifOutError seems to give an overall counter of all errors from the time the device has started - Am I correct about this?
    2) Is there any way I can get the interface-specific errors noted above via SNMP?
    Thanks,
    Mario

    Depends on the device and version of code, but most likely you will get what you want from the CISCO-IF-EXTENSION-MIB.  Look at objects like cieIfInRuntsErrs, cieIfInGiantsErrs, and cieIfInFramingErrs.  You will also get some ethernet-specific errors from the ETHERLIKE-MIB.

  • How do I get the Username of an AnyConnect VPN session via SNMP?

    I would like to monitor the usernames of my AnyConnect sessions via SNMP.  This will allow me to monitor, graph, report, and alert using Solarwinds Orion (or any other SNMP software).
    I would like to monitor this on my ASA 5520. I have run the show snmp-server oidlist command and I can see all of the OID's that I can poll. However, the OID I would like to poll crasUsername (1.3.6.1.4.1.9.9.392.1.3.21.1.1) is not working.
    Does anyone know how I can monitor the username of a AnyConnect session via SNMP?
    Below is a link to a great MIB reference for ASA Remote Access Monitor OID list.
    http://www.mibdepot.com/cgi-bin/getmib3.cgi?i=1&n=CISCO-REMOTE-ACCESS-MONITOR-MIB&r=cisco&f=CISCO-REMOTE-ACCESS-MONITOR-MIB.my&v=v2&t=tree

    Hello PDX,
    Welcome to the HP Support Forums!
    To get your issue more exposure I would suggest posting it in the commercial forums since this is a commercial product. You can do this at Commercial Forums.
    Regards,
    JERENDS
    I work on behalf of HP
    Please click “Accept as Solution” if you feel my post solved your issue, it will help others find the solution.
    Click the “Kudos Thumbs Up" to the left of the reply button to say “Thanks” for helping!

  • How to check current input/output rate on router subintenterface via SNMP?

    How to check current input/output rate on router (2821, etc..) subintenterface via SNMP, like cacti monitoring system.
    I cant find OID to make this with snmpwalk.
    Or there is no way to check current load by this way? Only polling?
    P.S. Ethernet subinterface, of course.
    With great respect, S.A.

    Hi,
    Try to use:
    1.3.6.1.4.1.9.2.2.1.1.6 - InBitRate
    1.3.6.1.4.1.9.2.2.1.1.8 - OutBitRate
    1.3.6.1.4.1.9.2.2.1.1.28 - ifDescription

  • The dot11Radio interface in AP 1250 stuck in reset status

    Anyone have idea why the dot11Radio interface in AP 1250 stuck in reset status? I have tried to no shutdown in CLI and enable in GUI but doesn't work.
    Aironet1250#sh ip int b
    Interface IP-Address OK? Method Status Protocol
    BVI1 10.1.119.67 YES manual up up
    Dot11Radio0 unassigned YES unset reset down
    Dot11Radio1 unassigned YES unset reset down
    GigabitEthernet0 unassigned YES other up up
    Aironet1250#
    Thanks in advance!

    oh, I forgot to assign ssid. It work now

  • How to reset password for a web user via GUI?

    Hi,
    How to reset password for a web user ID via GUI? is it possible?
    Thanks.

    Hi,
    You can  reset the pwd for the user through trascn SU01.
    BR,
    Disha.
    *Pls reward points for useful answers.*

  • Interface data rate readings fluctuate rapidly via SNMP

    Our cisco ASR 9000 router has been recently upgraded from 3.9.0 to 4.1.2, I'm monitoring the activity (traffic in/out)  of its interfaces via PRTG network monitor software, the readings I am getting now fluctuates alot and the utilization graph is showing high and low peaks, the graph is meaningless now and it's not smooth as it use to before, does anyone know the reason for this behavior ?

    Hi,
    I presume that this is the ACL rule that you have created
    object service http
    service tcp source eq www destination eq www
    access-list OUTSIDE_IN extended permit object http any object DEV_SERV
    And I presume that this is the Static PAT (Port Forward) configuration for the server you require access to.
    object network DEV_SERV
    host 192.168.2.32
    nat (data,outside) static xx.xx.xxx.xx service tcp www www
    While the NAT configuration seems fine if you want to do Static PAT and dont have a spare public IP address to do Static NAT, it does seem that your ACL rule is wrong.
    Notice that you define the service to be sourced from port TCP/80 and also destined to port TCP/80. The source port of a clients web server connection will probably never be TCP/80. It will be some random number above 1024 usually. You should only limit the connectivity on the basis of the destination port.
    So you could add this ACL configuration rather
    access-list OUTSIDE_IN permit tcp any object DEV_SERV eq www
    Let me know how it goes
    Hope this helps
    - Jouni

  • MDS9216 & MDS9124 Fabric Switches interface stats. via SNMP

    Dear All,
    I am interested in monitoring the interface statistics (In/Out bytes) of MDS9216 & MDS9124 Fabric Switches via SNMP and have been researching on what OID (MIB) values shall i poll? Would anyone be able to help me please? I have looked at many places but the closest I could get is the IF-MIB MIB Interface which has ifTable giving ifInOctets and ifOutOctest per port !  I am not sure if this is what i am suppose to poll as the ifInOctets gives 'the total number of octets recieved on the interface' and not the traffic ? What i am interested in is knowing the traffic (rx / tx) on the port at the time of polling so i can poll them say every 5 min. and plot them via something like cacti.
    Please let me know if any one has got any suggestion as I am not getting anywhere on this.
    Thanks in advance.

    ifSpeed I see listed here :-
    http://www.cisco.com/en/US/docs/storage/san_switches/mds9000/sw/rel_2_x/fabricware/mibs/reference/guide/mibiiobj.html#wp1044690
    not sure if that will give you what you need.  We use solarwinds to monitor our MDS's.

  • Incorrect bandwidth values via snmp?

    I have two cat 2900 16 port switches, for some reason when i read the bandwidth utiliz. values via snmp (PRTG, and MRTG give same results) i only show a steady 1-1.5 kbps up and down flow with occasianal spikes of the upstream to 2 or 3kbps..this is the same across all ports, now if i send something across the switch, nothing changes, nor is any other traffic i throw at the switch reflected... the peculiar thing is if i access the switch's web interface while conducting a 10.5 mbit transfer across the switch, i will see a spike of correct values (as i read on the hosts machines) reported by the snmp agents but only for 2 or 3 reads across 5 second periods..then its back to what i described again.. I've done factory resets on both and both of these snmp agents correctly read the bandwidht values from my dell and intel switches so i've ruled the agents out..
    any ideas?
    thanks, joe

    Thanks for the quick reply but thats not the problem. its not a units issue as i see somekind of traffic but when i'm maxing out the 100mbps port i see no change in the snmp reported graphs..but like i said i will see the actual values if i'm reloading or access the switches web interface.
    this is such a weird issue..and its affecting two swithces that are the same model but from different places.
    any ideas?

Maybe you are looking for