How to select the particles after using the Particle Analysis

Can I select the particles after the particle analysis directly, like chosing #1, #2 ..., or should I run the particle filter using the measured parameter?

Hello Ishi,
I now have a much better idea on what you are trying to do. If you run the IMAQ Particle Analysis Report VI on the thresholded image that contains particles, an array of clusters will be returned that will contain specific information for each particle including the area, number of holes, bounding rectangle coordinates, center of mass, orientation, and dimensions.
To find out which particle is which in the image, index the Particle Reports (Pixels) output of this VI, unbundle the cluster to extract the Bounding Rectangle cluster, and then pass it to the Rectangle input of an IMAQ Overlay Rectangle VI. This VI will overlay a bounding rectangle onto the image to show where the particle is located. You can specify which particle you want highlighted by changing the array index of the Index Array VI that is responsible for extracting a specific cluster of particle information from the Particle Reports output of the IMAQ Particle Analysis Report VI.
Regards,
Mike T
National Instruments

Similar Messages

Has any one managed to re-attach the stand after using the VESA adaptor?

I have just bought a 27-inch replacement for my 24 inch LED display and wanted to swap them over, using the 24" as an external for my MacBook Pro. The 24" was wall mounted and I had a VESA adaptor fitted. I took the 24" off and replaced with the 27" (looks great), but now I am unable to re-attach the 24" stand in a usable manner. The arm, which you are required to pull out and lock when you fit the adaptor, will not return into the back of the monitor: it remains locked and I have been unable to unlock it. The screen is therefore stuck in a fully forward position, meaning the only way I can use it is by kneeling on the floor in front of the desk. Not ideal.
Has anyone managed to successfully re-fit the stand to an LED Cinema Display, and if so was there a "trick" to it?

How to reattach stand to 27" iMac (2009)
I learnt the following;
1. Plan carefully - read the advise discussions on this Apple forum. It's a 2 x person job in places.
2. Tools - ensure you have the correct Torx screw driver or Allen key before you start as I learnt the hard way that
it is very very easy to round off the heads of the 8 x tiny little screws that attach the stand back onto the iMac.
3. If the screws don't come out easily you have a problem - After hours of trying I managed to get 6 of the 8
screws out - the other 2 I had to get a power drill and drill them through - lesson here is don't over tighten the screws
when you put them back in.
4 Don't worry if you do not have all 8 screws to put back in - I had 6 good ones left after the efforts to remove them
and this works fine as with most Apple things it is a slightly over engineered product.
5. Make sure you lay the iMac face down onto a blanket once removed from VESA arm.
6. Little tip - Once I had removed 4 of the screws I put wooden cocktail sticks into some the holes as I had read
in these forums that some "iMackers" had problems as the 8 x screw block had recessed back into the iMac itself.
If this happens it's very difficult to pull back out - hence the cocktail sticks to prevent this from happening.
7. Use a second person to hold the stand in place while you put the screws back into the iMac. (as stated don't over tighten them)
8. Now to release the latch to ensure the iMac tilt action works as designed. Be patient here especially with utilising the plastic card that came with the Visa mount which is optimised for this job - if you don't have one use a plain unbossed card. Recommend push the iMac fully forward and turn the lights down - then use a torch and shine into the area where the latch is - carefully insert card about 3/4 inch and release the latch - you can feel it release when successful - if you look carefully into the recess area with your torch on you can just about see it - second person helps here:)
9. Once latch is released by person one the second person slowly rotates the tilt action back and then forward throughout the full range of the iMac tilt action and hopefully that is you done:)
Overall - Not easy - frustrating at times - screws are a pain - plan carefully - have the right tool for the 8 x screws is a must - torch helps to find the release latch - to Apple I would say that the screws are not the best and of poor engineering quality which is unusual for you!
Hope this helps.
Kind Regards Alasdair.

After using the minidisplay port to connect to a projector, my computer screen displays images with less resolution than before. How do I get back the usual sharp resolution?

After using the minidisplay port to connect to a projector, my computer screen does not have the usual sharp resolution. How do I get back that sharp resolution? The computer screen images are now a bit blurry.

Do you mean after the projector is disconnected? It should change back to normal after disconnecting. If it does not, go to System Preferences > Displays and move the resolution setting back to the largest number.

How to load the boot menu using the command line , after the configuration change ?

how to load the boot menu using the command line , after the configuration change ?

Hi @Bask-48
Welcome to the HP Forums!
It is a terrific place to find answers.
For you to have the best experience in the HP forum I would like to direct your attention to the HP Forums Guide Learn How to Post and More
I grasp you are trying to change the boot order. Here is a link to Configuring the Boot Order in the System BIOS
that will assist you.
Good Luck and Happy Holidays!
Sparkles1
I work on behalf of HP
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos, Thumbs Up" on the bottom right to say “Thanks” for helping!

After 6 months of iPad bliss....My iPad has the incorrect apple ID how do I get it to use the correct one?

After 6 months of iPad bliss....My iPad has the incorrect apple ID how do I get it to use the correct one?

Settings > Store > Apple ID. Sign out and sign in with the correct one. Note that all apps are forever tied to the account they are purchased under.

OK, for the third time writing this this session, after setting up iCloud on my IPMini, how do I access the clod to use the iWork apps?

OK, for the third time writing this this session, after setting up iCloud on my IPMini, how do I access the clod to use the iWork apps?

Note that you can not log into iCloud.com through the browser on an iOS device, only from a computer. If you want to use the iWork apps on your iOS device, you will need to purchase the apps from the app store if you don't qualify to get them for free.

How to enable the screen after triggering the error message

Hi All,
we have a tcode IW31, in that one field(WBS element -PROID) is not mandatory. so we have written the following code to make it mandatory in a user exit EXIT_SAPLCOIH_010.It's triggering the error message, but it is going into disable mode. Please sugget me how to enable the screen after getting the error message triggering.
if not caufvd_imp-proid is initial.
select single * from t350 into wa_t350
          where auart    = caufvd_imp-auart
            and imord    = 'X'.
if sy-subrc is initial.
    pspel = caufvd_imp-proid.
else.
    call function 'CONVERSION_EXIT_ABPSP_OUTPUT'
         exporting
              input = caufvd_imp-proid
         importing
              output = l_posid.
    concatenate text-t10 l_posid text-t11
                into l_textline1 separated by space.
    message i208(00) with l_textline1.
endif.
else.
message e208(00) with 'Please maintain WBS element in Location Tab'.
endif.
Thanks

Hi,
Instead of error message use status message like
message s208(00) with 'Please maintain WBS element in Location Tab'.
Leave to screen sy-synnr.
This will allow to move to the screen and have in enable mode.
WIth Regards,
Dwaraka.S
Edited by: Dwarakanath Sankarayogi on Feb 13, 2009 7:46 AM

How can someone use a stolen iphone? does erasing the phone (which I feel like I should do) make it easier for the thief to use the iphone? If I don't erase it, it doesn't seem like anyone should be able to use the phone because of my password.

how can someone use a stolen iphone? does erasing the phone (which I feel like I should do) make it easier for the thief to use the iphone? If I don't erase it, it doesn't seem like anyone should be able to use the phone because of my password. Also, is it possible to retrieve anything that has been sent to the phone (i.e. text messages) since it was stolen through icloud? The "find my iphone" app says the device is offline but it rings when I call my number -- any idea how that would be the case? Thanks!!

You have a password, so good move on your part. Whether you erase it or the thief does, they still get to use the iPhone as theirs. Which is more important (pick one), protecting your data or punishing the thief?
Ringing occurs at the carrier. Chances are you're going to voicemail after only two or three rings. If you have an iCloud backup also a good move. Re-read my question in the first paragraph.

My keyboard freezes after using the option key... what gives?

I have a 17" MacBookPro with OSX 10.6.8
The problem: My keyboard key freeze after using the " option key" in Photoshop or when downloading a file using the option key.
I can usually use it 2 or 3 times before it makes a chirping cricket like sound… then my keys freeze up.? The only way to correct it is to restart.
Anyone else have or had this issue? it's frustrating. What's the deal?

hausman wrote:
tianmiao0304 wrote:
Thanks for your explanation!
Can I just bring my laptop to the nearest service center and get this problem solved directly? You know, usually it will takes several days to receive the backup keyborad, I can't wait
You'll have to phone the service center and ask. (When I lived not far from Lenovo's Canadian service center and wanted to bring in a ThinkPad for warranty repair they said that would be OK with them but my unit would be put on a queue the same as if I'd shipped it in. They simply didn't offer walk-in, while you wait service.)
In the interim it may or may not be possible to reattach the key, even just temporarily, depending on whether it wasn't put on properly at the factory or if it's physically broken in some way. Or you could use an external keyboard until Lenovo sends you a replacement, etc.
I've just call the local service center, he told me that he can not repair individual key, they can just replace the whole keyboard..... How bad luck I am!!!

How to rename a XML file using the file/FTP adapter

Dear All,
I am trying to rename a file using VARIABLE NAME SUBSTITUTION.
My structure:
<ns1:MSg xmlns:ns1="http://www.mycomp.inf.br/msr">
<ns1:MSgVal type="A" Id="188549">
    <ns1:cab>
      <ns1:PO>4500000000</ns1:cPO>
      <ns1:BI>90000000011</ns1:cBI>
    </ns1:cab>
</ns1:MSgVal>
</ns1:MSg>
How do I do to get the value 188549 from the field Id that is into the tag MSgVal?
I created a variable var1 and my reference is:
var1 --> payload:ns1:MSg,1,ns1:MSgVal,1,Id@,1
I am getting the error:
Could not process due to error: com.sap.aii.adapter.file.configuration.DynamicConfigurationException: Error during variable substitution: com.sap.aii.adapter.file.varsubst.VariableDataSourceException: The following variable was not found in the message payload: var1
Regards,
Fernando

Hi,
Like pinted by Michal, use Adapter Specific Identifers.
In your mapping set the file name using the code in this link and then in your Receivr File Adapter select the Adapter Specific Identifiers --> FileName .
http://help.sap.com/saphelp_nw04/helpdata/en/43/03612cdecc6e76e10000000a422035/content.htm
Regards
Bhavesh

I have finally figured out how to export an iphoto album so that I can maintain the proper order of the photos after burning the file. How do I keep each individual photo title and description after exporting and burning?

I have finally figured out how to export an iphoto album so that I can maintain the proper order of the photos after burning the file. How do I keep each individual photo title and description after exporting and burning? Presently after exporting and burning each photo is identified by the file name rather than each individual title description.

File name and Title are not the same thing.
Filename is attached to the Jpeg file in the Finder.
Title is attached to the photo within the Jpeg file - as is the description. These are written to the Exif and IPTC metadata on export.
So: File -> Export. Kind: Jpeg or Tiff and Check the box at 'Title and Keywords'. This will write the Title, keywords and descriptions (though not explicitly stated) to the metadata. This can then be viewed in any app that understand this material.
You can choose, if you wish, to also use the Title as a Filename - that's an option at File Name
Regards
TD

Duplicates & triplicate Calendar items on my ipad after using the iCloud..

i have duplicates Calendar items on my ipad after using the iCloud.. what am i doing wrong?? and how do i fix it?

This solved my triplicate calendar issue:
(short version)
Settings ==> iCloud. Turn off Calenders.
Delete exisiting calendar information when prompted.
Settings ==> iCloud. Turn on Calenders.
Restart Calender App.
(verbose version)
On your iOS devices go to Settings App ==> iCloud. Turn OFF Calendar Syncing. It will ask if you want to keep or delete previous Calendars on your phone, Choose Delete. Restart your Calendar app and see if it's squeaky clean. I had just birthdays and anniverseries. If you are still seeing items other than those (like birthdays) generated by the device then you are bringing in calendars from multiple sources. You'll need to turn off the other sources (if you have their entries duplicated already in the cloud).
Now go back to Settings ==> iCloud and turn the calender back on. Restart the Calendar app, everything should look good now.

After using the right mouseclick safari doesn't respond to any mouseclick

Hi since updating to safari 5.1.1 after using the right mouse click safari doesn't respond to any mouseclick anymore. I can use the keyboard and select menus but that is it. Reinstalled Safari, resetted safari and removed all preferences, caches and disabled all extensions etc. nothing helped. Any suggestions here?
Im using snow leopard, on a dual core mac Intel xeon desktop.

Solved it finally after a long time.. I was triggered that another user on the same system did not have the problem I scanned my user library folder: The problem was an old safari extender plugin in my Contextual Menu Items folder. After removal all is working again :-)

I am using adobe photoshop cs6. I am facing a problem. When i save any image as "save for web". After saving image it show cropped. An image show many parts of the image after saving the image. Please help me. Thanks in advance.

I am using adobe photoshop cs6. I am facing a problem. When i save any image as "save for web". After saving image it show cropped. An image show many parts of the image after saving the image. Please help me. Thanks in advance.

Just go back in photoshop and use the Slice Select tool, then just click and select the slice and hit delete - if you're not sure which one is the active slice just right click and find the one that has the Delete Slice option.
It's possible you either added the slices by accident or if you received it from someone they just had the slices hidden. For the future, you can go to View > Show > Slices to display (or hide) slices.

How to identify which applicarion is using the DVD burner?

How to identify which applicarion is using the DVD burner? Ot is not allow me to burn the DVDs genetrated in the Final Cut 7

I think you'll find that the application is Final Cut Pro... the message is bug. I get a similar message when disconnecting external drives after using them with FCP (even when the project is no longer loaded.)
As I mentioned above, the accepted workflow is to export the sequence to one of your hard drives using the Export>QuickTime Movie path with Settings:Current Settings and Make Movie Self-Contained checked like this:
This gets you a high quality "master copy" which you open in Compressor for transcoding. You should use the DVD: Best Quality setting for the duration of your movie.
this gets you the high quality MPEG-2 and AC-3 files for DVD Studio Pro authoring.
If you've never used DVD Studio Pro before, you can use iDVD instead. For iDVD, you just drag and drop your "master" on iDVD and it takes it from there. Both make a very professional product.
hope this helps.

How to select the particles after using the Particle Analysis

Similar Messages

Maybe you are looking for