How to set airport extreme as primary base??
Hi
I have just spent literally all day trying to get rid of the flashing amber, finally I now have a steady green light.
What I would like to know is what is the benefit of having the Airport extreme as my primary base and how do I do it.
regards
TIA
Lauren
laurynsausage wrote:
hi
I have an O2 wireless box ii
check the last post in this thread http://discussions.apple.com/thread.jspa?messageID=10696307�.
it talks about a time capsule, which is basically an airport extreme with an internal HD, so it should apply in your case as well.
good luck !
Similar Messages
-
I have airport extreme as my base, how do I use linksys as the extender
I have airport extreme as my base, how do I use linksys as the extender
You would need to connect the Linksys to the AirPort Extreme Base Station (AEBS) by Ethernet, and then, configure both of them for a roaming network.
-
I have Airport Extreme as the base unit and an Express unit in a room separated by a brick wall to improve signal. Express shows a green light indicating signal but my iPad does not perform well. How can I improve other than hardwire ethernet connection?
Other suggestions, and more info about the nature of the problem, may be in this Apple tech note.
http://support.apple.com/kb/HT1365
For example, you might find that the brick wall is not the only problem. There may be other devices pumping out enough wireless interference to be making things even worse.
I agree with Bob Timmons that Ethernet is best and most reliable. And that powerline (which I use) is easier and potentially faster than wireless...but only if your power lines do not have electrical devices plugged in which produce electrical noise on the line. Powerline will be slower than Gigabit Ethernet.
Ethernet cable is the only way to ensure that the signal goes directly there in a shielded way for a clear fast signal. Wireless and powerline are much slower because of all the other things the signal has to fight past to get to the other device. -
Airport Extreme Dual-Band Base Station Is excessively slow
Let me start off by stating this is my first apple support discussion and I have no experience in these forums but rather forums elsewhere.
My Airport Extreme Dual-Band Base Station is completely updated as of DEC. 30, 2012 running version 7.6.1 and I have the latest airport utility, so bare in mind some of the previous fixes I've Read seem unavailable to my setup
Our household has 7-13 of the following devices connected in a 24 hour average:
5-6 iPhones all running iOS 6 (1, iphone 3gs; 2-3, iPhone 4; 2, iPhone 5)
1 iPad 2 wifi only running iOS 6
2 MacBook Pro 13" early 2012 models one running mountain lion and the other running lion
1 mac mini early 2011 model running mountain lion server and is connected outside the network as a public server
1 Apple TV latest model(1080p) latest updates
1 LG 47" 1080p 3D TV
3 blueray players
2 Windows 7 PC one a laptop and the other a desktop
1 HP All-In-One Printer
1 AT&T MyCell Antenna
My problem is as follows:
My network is running rather sluggish. the base station is getting at the very minimum good signal strength to all my devices most of them getting great signal, so I doubt it be the result of range. I've tried messing with the channels and radio settings but have yet to find a correct optimal settings. I've tried searching around these forums as well as in other areas and have not found a suitable solution. my apple TV lags and jitters a lot. I have trouble airplay to it because of what I've read elsewhere which is latency issues. I have no clue how to test latency. I have realized that it isn't a matter of noise in the area because noise doesn't pass 15% and signal is optimal in all areas. of where the devices are. I've noticed connecting my server directly gives me 47Mb/s as compared to the Ethernet connection of 32Mb/s so I am clueless as to a solution. I know that with my old router the wifi speeds were outstanding but that router kept disconnecting wifi clients and then reconnecting them. sadly this is happening again with the apple router. last night my iPad would not stay connected and our network had so much lag that I couldn't even load the youtube app let alone a video. also buffering takes an odd amount of time sometimes 3 minutes. for a 30 second video on youtube. I have no guest network active and I have a wpa2/wpa personal encryption set on the network. I could use some serious help. the people of my household have no problem returning the apple router but I think to urge otherwise. if I could get some help in a solution that would be fantastic.
Thanks in Advance,
Blaine MillerCan you tell us whether your "modem" is a simple device with only one ethernet port or is it a "gateway", which is a combination modem/router with 3-4 ethernet ports?
-
Is my AirPort Extreme (802.11n) Base Station defective?
I'm trying to set up a wireless network with my new AirPort Extreme (802.11n) Base Station. I dismanteld my existing network that consisted of an old model AirPort Extreme and an AirPort Express. I can't seem to get anything to work properly with the new hardware. I have a G4 Quicksilver that uses an AirPort card. Is that the issue? I thought they were compatible. I was not able to update the Setup Utility because I don't have an Intel Mac. Still, that shouldn't prevent me from doing an initial setup. I'm thinking perhaps the unit is defective. I've been working on this several hours a day for almost a week. This is the most trouble (by far) that I've ever had with any Apple product. I'm really disappointed. I suspect the hardware is defective, but based on all of the issues I've read about in this forum, I think it could just be reflective of the poor overall quality of the new AirPort Extreme. What a let down.
What is the exact name of the application you are using to configure the airport?
You should be using "AirPort Utility"
It is a Universal application, so it should work on both a PPC and Intel mac.
As for the update, if you can't download it via software update, you most likely do not need it.
The quicksilver only has an Airport card:
http://support.apple.com/specs/powermac/PowerMac_G4_Quicksilver2002.html
That means that you will need to configure the airport extreme N to operate in the 2.4 GHz range. You will need to tell it that it needs to be compatible with 802.11b
There is probably an option for 802.11 b/g/n compatibility.
Are you going to still use your airport express? you could either use WDS to extend your wireless network without connecting the two airport base stations with an ethernet cable... or you could connect them together with an ethernet cable and configure the same network name and use two different channels (only use 1, 6, or 11). If you extend a network, they both need to use the same channel.
If the quicksilver is the only machine on your network, it will not be any faster.
Actually, you could make things faster, now that I think about it... I am guessing that your quicksilver is not located near your airport extreme. If I am wrong, just ignore this...
You could use one of your airports as your main base station, connected to your cable modem/dsl whatever... then you connect the other airports ethernet to your quicksilver. you then turn off the airport card in your quicksilver and set up the airport connected to your computer to use WDS and connect to the other airport using 802.11g.
You now have gone from an 11 mbps max (5 mbps real world) connection to a real world 30-40 mbps link.
Other options would be to look for 802.11g or 802.11n usb adapters for the quicksilver... I am not sure what is mac compatible out there, since it is probably a small market since it is built in to all new macs.
Good luck -
How to set security group as primary site collection admin and secondary site collection admin using powershell in sharepoint online site - office 365?
Hi,
According to your description, my understanding is that you want to set security group as admin of primary and secondary site collection using PowerShell command in office 365.
I suggest you can use the command below to set the group to site owner, then it will have the site collection admin permission.
Set-SPOSite -Identity https://contoso.sharepoint.com/sites/site1 -Owner [email protected] -NoWait
Here are some detailed articles for your reference:
https://technet.microsoft.com/en-us/library/fp161394(v=office.15)
http://blogs.realdolmen.com/experts/2013/08/16/managing-sharepoint-online-with-powershell/
Thanks
Best Regards
Jerry Guo
TechNet Community Support -
How to setup airport extreme vs express at WDS mode?
How to setup airport extreme(Main) vs express(Site) at WDS mode?
Please check out the following Apple Support article on how to configure a WDS.
-
How far does airport extremes range go
how far does airport extremes range go
Apple says up to 300 feet or so, but since tests like this are performed in a very large room with no walls, the specification won't mean much to most of us in the real world.
Bottom line is that it is not possible to make a good guess about distance capabilities in a home without knowing the number of walls and or ceilings the signal must pass through.
(A typicall wall of sheetrock and 2 by 4s will absorb on average about 15-20% of the signal and a ceiling absorbs more because it is thicker).
As a very rough guide...if the signal from the wireless router must pass through 4-5 walls, or a ceiling and 2-3 walls, then there won't be much of it left by the time it reaches a computer or other wireless device. -
How to start airport extreme on windows 7 professional
how to start airport extreme on windows
Doublechecking before proceeding ... are you getting a message saying that "the Bonjour Service can't be started" when you try to install iTunes? Or is something different going on?
-
Airport Extreme 802.11n Base Station blocking RealPlayer 11 completely
I am trying to play this radio station (just a brasillian sports channel) on RealPlayer 11:
rtsp://real.rbsonline.com.br/liverbs/*/broadcast/rdgaucha/gaucha.rm
Which is completely blocked on my Airport Extreme 802.11n Base Station with the latest firmware update.
It even blocks when RealPlayer is configured for HTTP only.
I am using it on my iMac which is connected directly via a ethernet cable instead of wifi to the Airport Extreme 802.11n Base Station.
RealPlayer can play it fine when I plug my iMac directly to the cable modem so it proves is the router. I never had RealPlayer issues before when I was using a linksys router.
It does really feel like Apple put an intentional block on RealPlayer to stop competition.
Anyone seen this issue? Guess it is related with the BBC RealPlayer issue.Fixed myself, problem was because I setup OpenDNS on base station, removed it now works
-
I am using an older AirPort Extreme as my base station and I want to extend the range by using a recently purchased AirPort Express. When I try to find either device using the AirPort Utilities function on either my new IPad 4 or my older MacBook Pro neither device is detected. However the utility is seeing that we are connected to the Internet which is through the Extreme. What am I doing wrong?
For now, leave the AirPort Express powered off.
Power off the entire network....all devices.....in any order that you want
Wait a few minutes
Power up the modem first, and let it run 2-3 minutes by itself
Power up the AirPort Extreme next, and let it run a full minute
Keep powering up devices one at a time about a minute apart until everything is powered up (leave the Express off for now)
Open AirPort Utility and check to see if the AirPort Extreme is visible.
If it's not, click the AirPort Utility menu at the upper left of the screen, then click About AirPort Utility. Post back with the version number of AirPort Utility that you see there....which should be AirPort Utility 5.6.1.
Post back on your progress. -
Recovering Old Datas on New Drive + Setting Airport Extreme Base Station old and new ones
Hello All,
Situation:
-iMac 24" Alu/2008/2.8 Ghz Intel Core 2 Duo/ 2Go DDR2 SDRAM
-2 Airport Extreme Base Stations mushroom type,
-1 Airport Extreme Capsule Model: A1143
The original 320 Go Hard Drive of my iMac crashed few months ago. A "technician" installed a new Hard Drive 235 Go while trying to recover all datas from old one. Failed.
No back up. The old disc needs to be unlocked in a dustless atmosphere. Quite expensive at the moment.
I decided to install OS X from sratch with the original Install Disc delivered with my iMac.
OS X is 10.5
Once on line I updated all pre-installed softwares. Among which Aiport Utility 5.6.1 today.
Problem:
I would like to get bigger hard drive disc, 1To for example. Does this still exist for this iMac 2008 Alu ?
How can I do to get my iMac again to OS X 10.9 ?. Does this mean I need to buy all intermediate levels again ?
How do I get my softwares (the ones on the original Disc: Pack office, Pages, Numbers, etc ...) back on track again, since my iMac is now more like down to factory level ?
Extending my internet provider from the WiFi router via my 3 Airport Extreme Base Stations: 2 mushroom type that need OS X + Airport Utility softwares at a certain level, while the Capsule might need another level. Right now I tried to set up the 3 of them with this Aiport Utility and though they all recognize the provider network, I can never conclude to extend it with the Base Stations: it drops the case. (WDS trouble which I don't even know what it is, or the Base Station simply desapears from Airport Utility scan, ...)
Thank you all for you attention.
Your comments are welcome especially if you have any knowledge on these various subject.
Can't wait to read your piece of advice.
Lionnel From Paris (France).me too... i connected my hard drive with all my music but i cannot see any of the music that used to be in my itunes... i checked and its there (when I connect the HD directly to my computer) but not when is plugged into the Airport Extreme... Please help!
-
How to downgrade Airport Extreme Base Station firmware?
I updated the firmware of Airport Extreme Base Station to 5.7 recently. However, I notice that the speed is very slow if one of the computer is downloading. I am thinking to revert the firmware to previous but don't know how to do it. Any advice and suggestion please?
ThanksSee if this helps.
http://discussions.apple.com/thread.jspa?threadID=285838&tstart=0
Cheers Don -
Need how-to for setting Airport Extreme for web cam access
I am running OSX 10.5.2 on a MacBook Pro. Have recently installed an Axis internet cam. Can see it fine within the home network, but do not know what settings to input into the port mapping area of the airport extreme to see if from other internet locations. Really would appreciate step-by-step guidance. Thank you!
Please check out the following AirPort User Tip for details.
-
Hi,
I have an existing modem/router from my ISP that does DHCP and NAT with base IP 192.168.1.1 distributed in the wireless network. I use this wireless network for our private devices. I could turn off the DHCP server in this first router, but there isn't a separate setting to turn off NAT.
I want to connect my Airport Extreme (4th gen) to this existing router to create a separate wireless network for visiting guests, where IP addresses of 10.0.0.0 etc. are used. So I do not want to use the Airport Extreme in bridge mode, as I would like to keep the devices on the first network 'invisible' for those on the second network. (P.S. when connected in bridge mode, the Airport works well and can distribute a network with a different name from the first. It's just that I would feel more comfortable about our privacy if the Airport were to distribute a different IP range. False security, maybe?)
I've tried doing this by 'Sharing a public IP address' in Airport Utility's Internet tab, leaving TCP/IP's setting to 'via DHCP', setting DHCP addresses to start with 10.0.0.2 up to 200 with all else blank, and not using a standard host nor NAT-PMP in the NAT tab.
When I do this the Airport complains of a 'double NAT issue'. Internet connectivity seems to be OK, but when switching between the two networks on my Mac I get complaints about my IP address being in use by another device intermittently.
Can anyone help in how to get the 'double NAT issue' resolved?
Thanks!So if someone is connected to the modem/router network they will be able to see the HD I will have put in to the AirPort Extreme?
As I said above.....since the modem/router and AirPort are bridged, devices on the modem/router wireless will be able to "see" devices on the AirPort wireless, and vice versa.....
If they can see the HD connected to the AirPort Extreme, will they be able to access it
Yes, unless you plan to password protect the drive connected to the AirPort Extreme.
or will they still need the password needed to get onto the AirPort Extreme network?
The modem/router and AirPort Extreme are bridged. They are on the same network. All devices are on the same network when the modem/router and AirPort are bridged. Not sure how else that I can say this.
Also, because it is bridged, I shouldn't have any problems accessing the HD I will have connected to the AirPort Extreme from an external location?
Accessing devices from a remote location is never easy....and a topic for a different post/discussion. If you have a "static" Internet IP address from your provider, and have all the details on how to forward ports on your modem/router, you are off to a good start.
Apparently there is some addressing issues because devices can be seen as "Double IP" because the modem/router would have allocated IP's as well as the AirPort allocating IP's thus making connections slower until resolved
When you "bridge", all IP addresses are issued by one device. There will be no conflicts on the network, since they are bridged.
Once again, in very simple terms, you have two doors (access points) that open into the same room (network). One "door" is the modem/router and the other "door" is the AirPort Extreme. They are on the same network....("room") because they are bridged.
Maybe you are looking for
-
Applications suddenly quit_Cursor Failure
One month ago I had to replace my Hard Drive (Seagate), added more ram and upgraded to 10.5... since than I've had a few problems: 1. *Cursor is not functioning properly*... When I try to highlight a word the cursor want recognize the starting point
-
I am getting inundated with SPAM/advertising messages. How can I eliminate this!
-
I have read through a lot of these complaints, and so far, just about everyonw having these problems installing have Windows XP home. Again, I will say that the Windows XP Home version that I have is an Upgrade OS and I had NO problems installing Jav
-
from 2 weeks ago i cant download any application when i want to get apps ( free & not free ) itunes shows me this error : click billing info , and verify your payment information in order to make purchaeses i have already 25 $ in my account what shou
-
I would like to create a new layer NOT AS SMART OBJECT. It is the default. How can I change it?
Hi! I would like to create a few layers, non of them should be a smart object. But when I create the layer automatically it becomes a smart object. How can I change it? Thanks!