How to set NAT Type in Airport Express for PS3

I just replaced my existing WiFi router with a Airport Express, using the same log in information, and all other devices includin iPhone and laptop can get on line w/o problem, but my PS3 can not seems to log in for on-line game, and when I check the internet connection settings, it show NAT type failed due to timeout error. I have read some articles about the need to change NAT Type from 3 to 2 or something like that, how can not find in Airport Utilities on how to open up NAT to change its type? anyone can help? Appreciate.

Unfortunately there are no specific NAT settings on the AirPort routers to change the NAT type. On the AirPorts you either have NAT enabled or disabled. Other options would be to use either a DMZ or open specific ports on the AirPort's NAT firewall to allow your PS3 to gain full access to  PS3's on-line gaming service.

Similar Messages

  • How to set up and configure AirPort Express for AirPlay and iTunes

    Saw somewhere that supposedly there were some apple written guidlines on the above topic. I have searched all over for them. Anyone know where I can get a copy to read through. Just trying to educate myself a bit and sety up another room with access to itunes, radio, etc with high quality speakers and amp off my express.

    Here you go ...
    How to set up and configure AirPort Express for AirPlay and iTunes

  • Can't find how to set up wires modem, Airport Express, imac

    My imac gets its internet using ethernet cable from cable modem (only one ethernet port out of it) to imac. Just bought airport express to send wireless signal to my house so kids can use wireless pc laptop. But want to keep my imac hard wired to internet. What cables do I need to plug in where?

    If your new AirPort Express is a 2nd generation model, then you would just need another Ethernet cable and connect it between the base station's LAN (opposing arrows) port and your iMac.

  • How do I add a second Airport Express for Airtunes only?

    I already have one Airport Express hooked up to my G5 for wireless internet. Works just fine. How, in simple english, do I add a second Airport Express to my downstairs stereo fot playing my iTunes music through.
    I have looked through the help sections, but it all comes across too complicated sounding. It can't be that hard.
    What do I do to set it up & NOT screw up my already working internet conection?
    I have the audio cable hooked up to my stereo/Airport Express downstairs & the Airport Express plugged in... "Yellow Light" lit on Express, what next?
    Thanks fellow Mac Fans!

    For the AX connected to the speakers:
    To set up AirTunes on the AirPort Express Base Station (AX), using the AirPort Admin Utility, connect your computer directly (using an Ethernet cable) to the Ethernet port of the AX, and then, try these settings:
    AirPort tab
    - Base Station Name: <whatever you wish or use the default>
    - Wireless Mode: Join an Existing Wireless Network (Wireless Client)
    - Wireless Network: <select the existing wireless network>
    Music tab
    - Enable AirTunes on this base station (checked)
    - Enable AirTunes over the Ethernet port (optional)
    - iTunes Speaker Name: <whatever you wish>
    - iTunes Speaker Password (optional)
    In iTunes:
    iTunes > Preferences... > Advanced > General
    - Look for remote speakers connected with AirTunes (checked)

  • How do I set up iPad with airport express to stream music to stereo without internet connection?

    how do i set up iPad and airport express to stream music to stereo without using internet connection.

    Your 4th gen iPad does have the necessary software to connect to the AirPort Express but not to administer it. To do the later, you would need to install the AirPort Utility applet.
    You said that your iPad can "see" the AirPort's wireless network, but can't connect. What happens exactly when you attempt to do so? Do any of your other wireless devices have any trouble connecting to the Express? Did you configure the Express for a closed network ... that is, not to broadcast its Network Name?

  • How can I set up an older airport express using the newest airport utilities?

    How can I set up an older airport express using the newest airport utilities? Seems like there isn't an option to set this up.  Normally you could add/set up this in the airport setup assistant- but that doesn't exsist any longer.
    Thanks for any suggestions 

    How can I set up an older airport express using the newest airport utilities?
    Unfortunately you can't, since Apple dropped support of the older AirPorts with AirPort Utility 6.x.
    Using some workarounds....not supported by Apple.....you might be able to download and install an older version of AirPort Utility that would allow you to administer the older AirPort.
    See this thread for more details and instructions:
    https://discussions.apple.com/message/21397085#21397085

  • ITunes Automatically Change EQ Setting Based On Which Airport Express Streaming?  I have two Airport Expresses running at my house. Both are connected to different types of speakers. Neither speaker set has its own equalizer, and both require a different

    I have two Airport Expresses running at my house. Both are connected to different types of speakers. Neither speaker set has its own equalizer, and both require a different EQ setting to sound just right. Does anyone know of a way to have iTunes automatically change its EQ setting based on which Airport Express it is streaming to?

    I'm in the same boat. I have a 6 zone amplifier running with 6 airport expresses to different rooms inside and outside the house. Each has it's own acoustic characteristics. I'd really love to be able to set each airport to equalize based on my SPL frequency sweep I did for each room.
    Setting the eq in itunes won't do it as that is global plus I have many more sources for auiod other than itunes that use the AEs directly.

  • How many people can simultaneously share airport express network?

    How many people can simultaneously share airport express network?  I want to set up a wireless network in my classroom and need to accommodate about 25 devices.

    The AirPort Express will only handle 10 wireless connections.
    You will need to consider an AirPort Extreme....which will handle up to 50 wireless connections.

  • How do I hook up my airport expresses to my internet that has ethernet from router to computer?

    Hello Community,
    I recently got new and better internet. In order for the 105 up speed, and 50 down speed to run to its full capacity I had to route my ethernet directly from the modem to the computer. I currently have a Wi-Fi Network that i am operating. Now I am looking to connect my two airport expresses to this new setup.
    One surpose being to run my speakers wirelessly and to activate wireless printing. The airport base stations I have are at least 3 years old. They have Ethernet, speaker, and USB connection.
    I am wondering how to do this?
    The airport expresses are:
    1. In the same room.
    2. In a different room.
    I am wondering if anybody knows how to activate the signal on both airport expresses. Both manually and/or via command lines and PPPoE, or DHCP type setups on the computer.
    Has anyone had experience configuring internet in this manner that can help?
    Thank you.

    Does the modem provide wireless or only wired? If the latter then you need to get a router or use one AEX as your main router and the other to extend that wireless network. Better yet is to get an Airport Extreme Base Station to use as your principal router.

  • Setting up Itunes on Airport Express -

    Hi, I am setting up itunes to play from my laptop wirelessly to my home stereo. I have airport extreme running fine for intenet, etc...
    I think I have wired everything correctly as far as airport express and my stereo.
    I installed airport express/itunes from the disk.
    when I open itunes, there are no "home speakers" as the manual would suggest.
    Any suggestions would be great. Thank you!

    I've had some success with setting up iTunes over Airport express. How are you connected to the internet?

  • Hi i got a new airport express for christmas and i set it up as per instructions ,i even give a static ip and wpa2 security ..the problem is is when i come to want to use it it says its not on my network and a orange triangle shows .when i reboot it works

    hi i got a new airport express for christmas and i set it up as per instructions ,i even give a static ip and wpa2 security ..the problem is is when i come to want to use it it says its not on my network and a orange triangle shows .when i reboot it works..then if i leave it a while and try iy agian its disapeared of my network...i have a bt hub 3 ....any help please ..im not sure if itsa faulty express

    I really don't have an answer for that one. I guess that while trying to get things working correctly, I would use the most basic monitor I had which in your case would be the Eizon using the Thunderbolt port and adaptor.
    When you boot into Safe Mode the startup is quite slow, but you should get the Apple logo and then the spinning gear below it (release the SHIFT key when it appears.) Then after a little more time you should see a gray progress bar appear below the spinning gear. When that disappears the computer will startup to a login screen.

  • How do I remove an unwanted Airport Express from my network?

    I have been using a Time Capsule for several years.  I am having trouble backing up to my Time Capsule.  I have discovered an unknown Airport Express in my network.  I've changed networks, added passwords to the network, etc.  How do I remove this unwanted Airport Express from my network?  I think he is wreaking havoc with my system!!  Help...

    Maybe this is an issue I should consult my ISP about??
    No question about that. If you can "see" Travis's device, then he can likely "see" your Time Capsule.
    I'm just concerned that whomever the APExpress belongs to could be changing settings on my computer or Time Capsule that would cause the issues with me not being able to backup.
    Make sure that you have a Time Capsule base station password. Unless a user has that password, they might be able to "see" your Time Capsule, but they cannot access any of the data on the Time Capsule or change the settings.
    Open AirPort Utility, click on the Time Capsule and click Manual Setup
    Then, click the Time Capsule tab below the icons to see the device name and password for your device. Make sure that you have entered the password and confirmed. Click Update if you have made any changes.
    The message I get is "The backup was not performed because an error occurred while copying files to the backup disk.  The problem may be temporary.  Try again later to back up.  If the problem persists, use Disk Utility to repair your backup disk."
    I am not sure what this error means, because I cannot duplicate it here to test.
    If it were me, I would try this "fix".
    http://pondini.org/TM/A5b.html

  • How can i connect my existing airport express to my new time capsule network?

    I have an older airport express for wirelessly extending my network in my apartment. I bought a new Time Capsule and my airport express flashes amber and cannot find the time capsule to connect. How do I get them connected?

    You can use the USB3 connections for USB2.  That's downward compatible.  Just runs at USB2 speed.
    Just this week apple announced a couple of TB adapters, TB-to-ethernet and TB-to-firewire.  But the FW adapter is not at the apple store as yet (at least at the time I am posting this).

  • How to set field type choice using csom (c#)

    I have a field type: Choice (menu to choose from) which is not multichoice. How do I set a value?
    I have found code for multiple choice but it doesn't seem to work for single choice.

    Hi,
    The following code snippet for your reference:
    newListItem["ChoiceFieldName"] = "ChoiceValue";
    newListItem.Update();
    clientContext.Load(newListItem);
    clientContext.ExecuteQuery();
    If you are assigning a Value which is not in the Choice Column, You need to create a choice value then assign it to the item.
    More information is here:
    http://sharepoint.stackexchange.com/questions/124999/how-to-set-field-type-choice-using-csom-c
    Best Regards
    Dennis Guo
    TechNet Community Support

  • I download itext  for convert jsp to PDF. How to set content type for PDF.

    I download itext for convert jsp to PDF. How to set content type for PDF. I try
    <%@ page contentType = "application/pdf;charset=TIS-620" %>
    , but the page does not PDF.
    Thank.

    PDF files are usually binary files, JSPs are not well-suited for binary content.
    (If you download the result of your JSP you'll see that it is not a valid PDF file; it will have probably a lot of whitespace and linefeeds, that will choke your PDF reader.). The first few characters must be
    "%PDF-" without whitespace.
    You can try using PDF files encoded as text - check if you can use text-encoded PDFs in iText.
    Try using a Servlet instead.

Maybe you are looking for

  • Loans document error Document header does not have a reconciliation key

    Hi All, I am trying to post a loans document through EK25 and while saving the document following erros is coming Formal error: Document header does not have a reconciliation key Message no. >0037 Diagnosis You tried to post a document but a reconcil

  • X200 auto-update BIOS upgrade failed? system no longer boots

    Hi, I've had an X200 for around 7 months now and just did an auto-update earlier today. One of the items was a BIOS update, so I thought what the heck, it should be fine, always has been before. The update completed correctly and shuw down for reboot

  • Web Start doesn't leave the gate on Linux and Mac

    I am evaluating Java Web Start to decide whether to recommend it as part of a government grant proposal. My initial impression of Web Start has been a sorry one. When I go to http://java.sun.com/products/javawebstart/demos.html and click on one of th

  • Problems calling stored procedure with DG4IFMX

    Hi guys, I am trying to call stored procedures from Informix Database which is connected through Oracle Database Gateway for Informix. I have run select,update,delete successfully but when i try to run a stored procedure nothing happens. for example

  • Is there a limit to how many pages my form can be?

    Im at 6 so far and I just started. it is very dynamic and there is a lot of show/hide fields. It is basically 6 forms in one. I am worried that by the time i finish itll be too big.