How to set up a guest LAN? (small business, simple environment)

First before getting into my actual post, please allow me to briefly express my sincere aggravation at this Cisco website for it's lack of proper IE 11 support.  When I try to create a forum post, well, there is no way to do it.  The old Create a Discussion link is gone (actually when I log into my profile, the entire Actions pane is gone).  The Ask a Question thing you first see is terrible, it doesn't support IE 11 apparently because the message body field is just gone.  I can put a Title, and tags, but there is no field.  there's also no compatibility mode button anywhere in the IE 11 interface one this site.  I was lucky in that the Actions pane shows up when you click on another person's post.  I don't think Cisco realizes how absolutely annoying that kind of thing is. 
I have a single 192.168.0.0/24 LAN with a single Cisco SG300 series switch to aggregate all the network connections, a single gateway firewall/router to the Internet, and a few wireless access points on the same LAN.  These are the AP541N's.  My goal is to set up guest Wi-Fi, but have it that guests cannot see or access the internal network. 
Haven't not actually done this before, I have no idea where to proceed.  I know I can create guest virtual AP's in the AP541N but that doesn't do anything to prevent a guest device from having full access to all of 192.168.0.0/24 computers. 
What can I do?  Do I have to put in completely new hardware?  Should I be contacting the Cisco Small Business tech support group if the specifics are unique to the SG300 and AP541N models? 
Any help is appreciated, both general advice but ideally a full solution reply can be possible :)

Hi Valley ITPC,
Here are some suggestions regarding the IE11 issue from the support team:
How to off compatibility mode on IE 11 by following the instructions given on the link below:
Assuming its IE11 on Win 7. http://windows.microsoft.com/en-us/internet-explorer/use-compatibility-view#ie=ie-11-win-7
if not use this link http://windows.microsoft.com/en-us/internet-explorer/use-compatibility-view#ie=ie-11
Hope this helps.
Regards,
Cindy
Cisco Small Business Community Manager
www.cisco.com/go/smallbizsupport
twitter: CiscoSBsupport

Similar Messages

  • How to set up different virtual LANs (using the E3200)?

    Hi.
    I would like to set up different virtual LANs (using the E3200) so that I can have two different networks that can't access each other.
    The E3200 is connected to a modem for internet access.
    I would like both networks to have access to the internet.
    Does the E3200 alone support creating virtual LANs?
    If not, is there another way I can meet the requirement using the E3200 alone (using something other than virtual LANs)?
    I'm ultimately thinking that I would need at least one other router.
    So for example,
    Router A (E3200) is connected to the modem and setup for DHCP using a LAN IP range 192.168.1.1/24.
    Router B is connected to Router A and setup for DHCP using a LAN IP range 192.168.2.1/24.
    In this way devices connected to Router A should not have access to devices connected to Router B and visa-versa, correct?  For example, Device X connected to Router A cannot ping or browse files on Device Y connected to Router B and visa-versa, correct?
    Would I need to setup anything else on Router B?  For example, do I need to setup DNS settings so that devices connected to Router B can connect to the internet without issue?  Would I need to specify that these virtual LANs are not bridged, and on which router, or both?
    I already know how to set up a static IP, DHCP, LAN IP ranges, and static DNS settings on a router, etc.
    In regards to wireless devices, I am thinking they would follow the same pattern; so wireless devices connected to Router A (E3200) have access to other wired and wireless devices connected to Router A but not to wired or wireless devices connected to Router B and visa-versa.  However, if wireless devices currently don't have access to wired devices also connected to Router A, then that is fine for now.
    Thank you very much!
    -Rami
    Solved!
    Go to Solution.

    The E3200 has no VLAN support according to the manual. There's no way to configure two separate networks with this router alone.
    You will need to add network electronics.
    Ex:
    Managed Switch with VLAN
    Another wireless router with VLAN
    If your modem supplies multiple public or private IP addresses then you could put a switch after the modem and two wireless routers attached to the switch.
    Please remember to Kudo those that help you.
    Linksys
    Communities Technical Support

  • How to set up Pymnt Method for different business units

    Hi,
    Can anyone shed some light as to how to set up P Method in FBZP in a way that one type can be identified according to its Business Unit?
    To clarify, FBZP is currently set up in a repeated way:
    Pymnt Methods:
    T - Transfer - Business Oil
    S - Transfer - Business Engineering
    V - Transfer - Business Equipment
    A - Boleto - Business Oil
    N - Boleto - Business Engineering
    C - Boleto - Business Equipment
    As you can see, we are repeating same payment method as it is needed for business to identify which business unit this refers to.
    Is there a way of setting up only one type of Transfer and one type of Boleto and how this will categorize the type of Business Unit ??
    Any input is welcome
    Regards
    Roger

    Hi Roger:
    How about some enhancement on F110? The logic would be something like read all the proposal lines, group by profit center and then re-assign the payment method based on profit center. There are couple of user exits available starting with RFFOX###, depending on the payment method and the program you using.
    Something similar to substitution rules user exit.
    Not sure if there is any other standard configuration to combine lines by profit center.
    Thanks.
    Rahul

  • How to set the domain of a cookie in localhost environment

    in some scenario i have to set the domain of cookie on my local environment,
    how can be done?????????????
    i.e http://localhost:7001/myapp/testservlet
    how to set the cookie domain for "myapp"

    Hi
    After Some googling I could find out this for you. I think it is a bug with IE.
    http://www.webmasterworld.com/forum21/11530.htm
    The idea is to use a virutal host.
    HTH
    VJ

  • How to use Adobe Anywhere in a small business environment.

    Thanks in advance for any help. 
    Our marketing agency has a small 1000 sq ft video studio with a couple fully loaded 27" iMac's with additional thunderbolt displays and a Pegasus 2 16TB Raid thunderbolt drive.  I collaborate with remote editors every week but we always have issues with keeping every with the right hd footage and then re-archiving back at the studio with the correct project files, footage, most recent edits etc.
    My question is what does it take as a small business to implement Adobe Anywhere?  Do you have any examples of how you have implemented it in your business? What kind of cost is involved to make this switch? 
    We are getting ready reconfigure a number of things in the studio next week and this would be a great time implement a new remote configuration as well if possible so any help would be greatly appreciated.
    Kind regards,
    Chris

    Adobe Anywhere http://www.adobe.com/products/adobeanywhere.html
    http://www.creativeimpatience.com/adobe-anywhere-enterprise-solution/

  • How do i create a database for small business use?

    I have a small business and need to be able to email flyers to clients, What are some options for setting up a customer database?

    Unless you really want to host a mail server (which can add complication to your life) then I would look at a hosted solution.
    listbox.com
    icontact.com
    etc

  • How to create Down Payment Invoice without Small Business One

    Greetings,
    I have a requirement to create an AR Invoice to solicit a Down Payment (previous to any Goods Issue).   I see from other postings that this can be done using Small Business One, but we only have the SAP ERP 5.0 implemented.    The customer has agreed to Down Payments, but will only submit payment after receiving an invoice.
    Is this functionality available in SAP 5.0?
    Thanks,
    Tony-

    Closed due to non-response.

  • How to set global ip in lan

    hi guys.
    I am new to cisco .i have some basic question to ask.
    in my situation .i use a cisco 1841  .
    ethernet 0/0 .i set serval vlan in this port .with the address 10.x.x.x /24
    ethernet 0/1 .i set a global ip in it .with address of 219.x.x.x .and i have another global ip preserved .
    the nat is ethernet 0/0 ----> ethernet 0/1 .
    and my question is: how to create DMZ .i want to set another global ip in my Lan.
    how can i do this setting.
    any suggetsion?

    Thanks a lot .
    it work well for me now .
    i have a another question.
    i set the nat to gloable ip .and it works.i set it by the Cisco Configuration Professional
    in the edit the static nat.
    but there is a abnormal .
    when the electronic is down. the setting change to the old one.
    so what is the problem?

  • HT5569 how to set a prefered Wireless LAN list on iphone

    I wan to set a list to tell WI-FI joing this network (XA) firstly if not available join (XB) and so on.
    Is there any feature like this on the iphone, i am using iphone 5 with IOS 7

    It depends on where is contacts are on his phone.  If they are stored locally in the "On My iPHone" account, all he would need to do is go to Settings>iCloud, sign in with his Apple ID to create his account (or sign in with an existing iCloud ID if he already has one) and turn Contact On.  They will then upload to his iCloud account.
    If they are being synced with an external service such as Gmail, Yahoo, an exchange account, etc., they will have to be copied to his iCloud account in order to sync them with iCloud.
    Unless you already know, have him open the contacts app on his phone and tap Groups (if he has any contact groups).  Does he have any non-iCloud accounts listed, such as On My iPhone, Gmail, Yahoo or an exchange account?  Also have himego to Settings>Mail,Contacts,Calendars>Default Account (in the Contacts section).  Does he have the Default Account setting in the Contacts section, and if so, what is selected as his default account?

  • How to set Debugging level FINEST in the different OS environment

    Hi All,
    Please help me out to get system logs with debugging mode set as FINEST.
    I want to know how to get system logs finest.
    Is there any xml configuration in root folder?
    Please help me out to get the logs for different environments like windows or unix etc.
    Regards
    Abhishek

    Hi,
    The Ubuntu 14 not supported by Win8 Hyper-V, personal experience is same with Andrew_Grant, you can try to install the last Integrations Services.
    The related KB:
    Ubuntu virtual machines on Hyper-V
    http://technet.microsoft.com/en-us/library/dn531029.aspx
    Hope this helps.
    We
    are trying to better understand customer views on social support experience, so your participation in this
    interview project would be greatly appreciated if you have time.
    Thanks for helping make community forums a great place.

  • How to set the card name of wml in Simple Result?

    Hi,
    I nned to set the card name appearing in the WML device (browser show the name of the card in the top of the screen)
    How do i set an page tile in SR? I cant find such a parameter any where on the tags... Ideas?
    Regards,
    Lars

    Lars,
    You may use SimpleTitle element to display the title. See the following example copied herewith from developer's guide.
    <?xml version = "1.0" encoding = "UTF-8" standalone="yes" ?>
    <!DOCTYPE SimpleResult PUBLIC "-//ORACLE//DTD SimpleResult 1.1//EN" "http://xmlns.oracle.com/ias/dtds/SimpleResult_1_1_0.dtd">
    <SimpleResult bgcolor="99ff99">
    <SimpleContainer>
    <SimpleText>
    <SimpleTitle>Seach Result</SimpleTitle>
    <SimpleTextItem>
    <SimpleEm level="strong">1 Entry found</SimpleEm>
    <SimpleBreak msecs="500"/>
    <SimpleStrong level="strong">Chandra Patni</SimpleStrong>
    <SimpleBreak/>400 Oracle Pkwy
    <SimpleBreak/>Redwood Shores
    <SimpleBreak/>CA, 94065
    </SimpleTextItem>
    </SimpleText>
    </SimpleContainer>
    </SimpleResult>

  • How to setting for the number range for Business Partner

    Dear Sir,
    I create the new role for Business Parnter , However, I would like to set the new number range for that buiness Partner with that role.
    Please kindly advise what is the step to do.
    Thank you and best regards,
    Vimol

    Hi Vimol,
    In CRM  standard system it is not possible to link specific role with specific grouping. 
    To achive the same go to following IMG path:
    SAP Implementation Guide>Cross-Application Components>SAP Business Partner>Business Partner>Basic Settings>Number Ranges and Groupings>
    Define Groupings and Assign Number Ranges
    Hope you selected the opton button for column 'Int Std.
    I already suggested a work around above.
    Best Regards,
    Satish Mathala

  • How do I set up a guest account using the AirPort Express  2nd Generation?

    I Just purchased a new 2nd Generation AirPort Express.  The features list and the set-up guide says that I should be able to set up a guest account, but nowhere have I found how to do this.  I am running AirPort Utility 5.6 on my MacBook Air under Lion and I even get a message that I should not make updates using version 5.6 because it is not the appropriate version for the 2nd generation AirPort Express. Software Update says there's nothing new for me. When I search the Apple support site there is not even a version of AirPort Utility 5.6.1 for Lion though there is one for Snow Leopard.  Even when I installed that version on my Mac Mini running Snow Leopard, I could see no way to create a guest account.
    I came across a YouTube video describing a demonstrating how to set up the guest account on Time Capsule and the AirPort Exteme. There it's quite obvious because in the General section there is a tab for setting up the guest account.  There is no such tab in either version 5.6 of the AirPort Utility I'm running under Lion or version 5.6.1 running under Snow Leopard.
    What am I missing?
    -Bill

    Apple assumes that you are connecting the AirPort Express to a simple modem....not a modem/router or gateway type of device......that provides both modem and router functions in one enclosure.
    If you have the AirPort Express connected to a gateway device, the Express is detecting that another router is present on the network, so the Express operates in Bridge Mode to prevent the conflicts that would normally occur when two routers are on the same network.
    Open AirPort Utility 5.6, select the AirPort Express and click Manual Setup
    Click the Internet icon, then click the Internet Connection tab
    If the Connection Sharing setting is currently configured to "Off (Bridge Mode)", the Guest Network cannot be enabled with the type of "modem" that you have without breaking some basic networking rules.

  • How to set up guest password?

    I still cannot figure out how to set up a guest password on my wireless network.  I'm trying to use 192.168.1.1 but dont see an obvious place to set the information.  And do I have to connect to router to the laptop before making the changes?

    Well what model number router do you have?  If it is a E series you must load and run the Cisco Connect software to configure the Guest Network.

  • Form Action/PHP within iWebsite - for Small Business ... SEO too ...

    Can anyone tell me how upgradeable iWeb is realistically for a small business website ... specifically for a customer mailing list form ...
    I am creating a mamp back-end for a small start-up and want to get a feel for what I'm up against when I get around to creating a targeted email campaign. Can IWeb really scale up to this ... ??? The iWeb page on the Apple site is not very encouraging.
    Also, how about SEO ... ??? Can I access my HTML? How do I get around that template in other words ...

    iWeb is not the problem when setting up form mail - MobileMe is.
    You need to publish to a good commercial hosting service that will allow you to run scripts.
    iWeb is template based but you can access the code in the published files.
    There isn't really any need to do this as far as SEO is concerned. Have a look at Rage's SEO Tool....
    http://www.ragesw.com/products/iweb-seo-tool.html
    Its freeware and even I can work it!

Maybe you are looking for