How to set up Airport Extreme for 11ac and 11n?

I have just purchased the new Airport Extreme (August 2014) because Apple's website states
Simultaneous dual-band support.
AirPort Extreme features simultaneous dual-band 802.11ac Wi‑Fi. That means it transmits at both the 2.4GHz and 5GHz frequencies at the same time. So no matter which band your wireless devices use, they’ll automatically connect to the best available band for the fastest possible performance.
I have number of Macs in my home from a new MacBook Pro with Mavericks to a Macbook Air with Snow Leopard (due to required software) and iPads.
So after setting up the new Extreme my new MacBook only accesses 11n as does my older Macs. I checked by holding down the option key while clicking the WiFi icon at the top of my Mac. Well, not so automatic then as I was expecting 11ac and 3 times faster access (as stated by Apple).
I then looked for some documentation for setting up but cannot find anything.
Hence my question here.
How to set up Airport Extreme for 11ac and 11n simultaneously?
At present the new Extreme is no better than my previous 2 year old one.
Thank you.
Michael

How to set up Airport Extreme for 11ac and 11n simultaneously?
Assuming that it is operating correctly, 802.11ac and 802.11b/g/n are broadcast simultaneously by default.
Simultaneous dual-band support.
AirPort Extreme features simultaneous dual-band 802.11ac Wi‑Fi. That means it transmits at both the 2.4GHz and 5GHz frequencies at the same time. So no matter which band your wireless devices use, they’ll automatically connect to the best available band for the fastest possible performance.
That is advertising. The real information is usually found in the small and hard to read footnotes:
Based on theoretical peak speeds. Actual speeds will be lower.
AirPort Extreme is based on an IEEE 802.11ac draft specification. Performance based on comparison with Apple’s 802.11n products. Comparison assumes AirPort Extreme network with 802.11ac-enabled computer. Speed and range will be less if an 802.11a/b/g product joins the network. Accessing the wireless network requires a Wi‑Fi-enabled device. Actual speed will vary based on range, connection rate, site conditions, size of network, and other factors. Range will vary with site conditions.
Since the 802.11ac signal is being broadcast only using the 5 GHz band, some users report that they have had better results by using the option to assign a different name to the 5 GHz band, and then pointing their Mac to that specific signal or network. You may want to try that option.
But first as a test, please locate the MacBook Pro about 10-15 feet or 3-4 meters from the AirPort Extreme with clear line-of-sight between the two devices. Restart both the AirPort Extreme and the Macbook Pro and then check to see if the Mac is connected to an 802.11ac signal.
If not, please power off your other wireless devices...computers, mobile devices, etc. temporarily, and try the same test again.
Please report on your results.

Similar Messages

  • How to set up Airport Extreme with Charter ARRIS Modem TM902A for the first time for WIRELESS.

    How to set up Airport Extreme with Charter ARRIS Modem TM902A for the first time for WIRELESS.
    When Charter Tech goes to your site, have them connect the modem up, but do not connect the modem to your iMAC or MacBook Pro.  What you want to do is connect the Airport Extreme to the iMac or MacBook Pro first with the Ethernet Cable. You have to do this to configure via Airport Utility to set up the Base Station Name & Base Station Password.
    You will then create/configure a Wireless Network, create your Wireless Password that will be entered on each of your Devices, example, Apple Tv, your iPhone, etc., you want to allow access to your Wireless Network you are creating.
    Wireless Security will be -> WPA/WPA2 personal or just WPA2
    Enter the Wireless Password you want
    Verify the Wireless Password (enter it again)
    After it is created you will see it on the Airport Utility window with the name you created for it and to the left, will be a Dot (circle that will be yellow).
    Next you then want to unplug the power to the Airport Extreme, and then take the end of the Ethernet cable you unplugged from the iMac or Lap top MacBook Pro and connect it to the back of the Modem.
    Next unplug the power cord from the modem and wait about 5 minutes, then plug the power back into the Arris Modem and wait until all lights come back on the modem wait
    about 5 minutes, then plug the power cord back to the Airport Extreme and you will see it the light blinking yellow.  Wait about 5 to 10 minutes, during this time Restart you IMAC or MacBook Pro, and once it is back up click on the Airport Utility and you should see on the Airport Utility screen.
    For INTERNET to the left the light should be green and you should see the Airport Extreme also appear and the light to the left on the screen should also be green.  If they are, you then should be able to click on the Wireless Symbol on top of bar of the screen and click to select the Wireless Network Name you created.
    If you Do Not See the light (Icon) next to INTERNET turn Green, or if you see the Internet Light Green, but the Light (Icon) next to the Airport Extreme is yellow, unplug the power again to the modem and unplug the power again to the Airport extreme and wait about 15 minutes or up to 30 minutes. Then plug the power cord back to the modem wait till all the lights light up then, plug the power cord back into the Airport Extreme and Restart your iMAC or MacBook Pro.
    The Airport Extreme light should change from yellow to green. Open up the Airport Utility to see what the indicators are showing they should both be green.  Again select Wireless network you created under the Wireless Icon on the top right of the screen. Open Safari and see if you are able to Route to a web page or the apple site should appear.
    WHAT TO DO IF YOUR AIRPORT EXTREME WAS PREVIOUSLY SET UP FOR USE WITH ANOTHER CARRIERS ROUTER OR MODEM.
    NOTE:  If you already had your Airport Extreme connected for example, I previously had ATT Uverse and the Airport Extreme was connected to the Wireless Router Model 3801HGV, I disabled the Uverse Wireless and used the Airport Extreme for the Wireless signal in bridge mode, as the Airport extreme Signal is much stronger than the Uverse router, and I was able to obtain a Wireless signal with the Airport Extreme way much better with no signal loss which was very very frustrating with the Uverse router.
    Anyhow if you had it hooked up like this, now that you will be using it with the Charter ARRIS Modem TM902A, you will need to reset the Airport Extreme to clear out the old data it has in memory, with the previous set up otherwise it will not work. Trust me I spent 6 hours trying to make it work reading all Apple Support Community questions and answers relating to this type issue/problem others have been having trying to get their set up working. I tried all the tips, and I finally decided just to see if by chance I would be able to connect with someone with Charter Tech support who might be familiar with Apple to be able to assist me and by luck I did.  He told me why it was not working and was all due the previous configuration with the ATT Uverse router was still in memory with the Airport Extreme. Finally it was 10:30 PM when I decided to call Charter Tech Support and I had been working on this since 3:00 pm pacific. I did not call them earlier as all the post I read said they never received any good help from Charter. After calling them I finished up by 11:00 PM and was able to finally connect Apple Tv, iMac, iPhones and Macbook Pro. We love our Apple Product and Happy all is connected with the new
    Internet Provider Charter. I must say the speed is way way much better than it ever was with AT&T Uverse. 
    THIS IS WHAT YOU WILL NEED TO DO:
    First you will need to unplug the Airport Extreme, then by taking the tip of a pen or paper clip end you need to push the reset button on the back of the Airport Extreme and hold it
    down and at the same time plug the power cord back into the Airport Extreme count to 5 or 10 then release the reset button. Then once he light in front of the Airport Extreme stops blinking you need to plug the Ethernet cable from the Airport Extreme to your iMAC or Macbook Pro, and restart which ever one you have, then open the Airport Utility once it is back up.  If you see airport extreme pop up with the old network name or it shows and yellow triangle click on the Airport Extreme ICON it will not let you configure it but will ask if you want to get rid of it or remove and just do it.  Then Again restart your iMAC or MacBook Pro, open up Airport Utility again, and on the top left you should see under “Other Airport Base Stations” the MAC ID for the Airport Extreme.
    You will then create/configure a Wireless Network, create your Wireless Password that will be entered on each of your Devices, example, Apple TV, your iPhone, etc., you want to allow access to your Wireless Network you are creating.
    Wireless Security will be -> WPA/WPA2 personal or just WPA2
    Enter the Wireless Password you want
    Verify the Wireless Password (enter it again)
    After it is created you will see it on the Airport Utility window with the name you created for it and to the left, will be a Dot (circle that will be yellow).
    Next you then want to unplug the power to the Airport Extreme, and then take the end of the Ethernet cable you unplugged from the iMac or Lap top MacBook Pro and connect it to the back of the Modem.
    Next unplug the power cord from the modem and wait about 5 minutes, then plug the power back into the Arris Modem and wait until all lights come back on the modem wait
    about 5 minutes, then plug the power cord back to the Airport Extreme and you will see it the light blinking yellow.  Wait about 5 to 10 minutes, during this time Restart you IMAC or MacBook Pro, and once it is back up click on the Airport Utility and you should see on the Airport Utility screen.
    For INTERNET to the left the light should be green and you should see the Airport Extreme also appear and the light to the left on the screen should also be green.  If they are, you then should be able to click on the Wireless Symbol on top of bar of the screen and click to select the Wireless Network Name you created.
    If you Do Not See the light (Icon) next to INTERNET turn Green, or if you see the Internet Light Green, but the Light (Icon) next to the Airport Extreme is yellow, unplug the power again to the modem and unplug the power again to the Airport extreme and wait about 15 minutes or up to 30 minutes. Then plug the power cord back to the modem wait till all the lights light up then, plug the power cord back into the Airport Extreme and Restart your iMAC or MacBook Pro.
    The Airport Extreme light should change from yellow to green. Open up the Airport Utility to see what the indicators are showing they should both be green.  Again select Wireless network you created under the Wireless Icon on the top right of the screen. Open Safari and see if you are able to Route to a web page or the apple site should appear.

    I just got a Charter Modem. Model TM822. While I was moving, my Airport Extreme was still at my old place.
    I have a Linksys WRT320N I used for the initial Charter setup.
    I can get my Airport to work here, but the Internet light on the Modem flashes Yellow.
    Hasn't caused any issues so far but one thing I did notice.
    On the Linksys there were 3 DNS servers listed.
    The Airport Extreme only lists 2 and i don't see where I could add another, only change whats already there.
    I tried everything above, but light on modem still flashes yellow.
    I have the technicians cell phone. Told me "that shouldn't be" and gave the same advice listed above.
    I'll break down and call Charter one day, see if it's on their end. NSA tracking may need a reset LMAO.

  • How to set up airport extreme with TPG ADSL2 ?

    How to set up airport extreme with TPG ADSL2 ?

    I just got a Charter Modem. Model TM822. While I was moving, my Airport Extreme was still at my old place.
    I have a Linksys WRT320N I used for the initial Charter setup.
    I can get my Airport to work here, but the Internet light on the Modem flashes Yellow.
    Hasn't caused any issues so far but one thing I did notice.
    On the Linksys there were 3 DNS servers listed.
    The Airport Extreme only lists 2 and i don't see where I could add another, only change whats already there.
    I tried everything above, but light on modem still flashes yellow.
    I have the technicians cell phone. Told me "that shouldn't be" and gave the same advice listed above.
    I'll break down and call Charter one day, see if it's on their end. NSA tracking may need a reset LMAO.

  • How to setup the Airport Extreme for PSP?

    Can anyone tell me how to setup the Airport Extreme for PSP? I have been searching the Discussions but none of the posting seems to explain detail enough. A step by step guide would be very appreciated. Thanks.
    PowerBook G4   Mac OS X (10.4.3)  

    Sorry, I forgot to mention a few points:
    1) I don't have the Airport Extreme base station;
    2) My PowerBook is connect to the internet thru wired connection with the Built-in Ethernet;
    3) The Airport is turned on, but my PSP's scan cannot locate the PowerBook at all (while it find someone else's network)
    So, I wonder if I can just connect my PSP to the built-in Airport in the PowerBook directly. So that I can have internet access on my PSP.

  • How to setup the airport extreme for window xp

    How to setup the airport extreme for window xp

    Sorry, I forgot to mention a few points:
    1) I don't have the Airport Extreme base station;
    2) My PowerBook is connect to the internet thru wired connection with the Built-in Ethernet;
    3) The Airport is turned on, but my PSP's scan cannot locate the PowerBook at all (while it find someone else's network)
    So, I wonder if I can just connect my PSP to the built-in Airport in the PowerBook directly. So that I can have internet access on my PSP.

  • Hi having trouble setting my airport extreme for guests?

    hi having trouble setting my airport extreme for guests?

    This is likely because you have the AirPort Extreme connected to a modem/router, or gateway device.....and not a simple modem. Can you provide the make and model number of your "modem", as we previously asked?

  • Having trouble setting my airport extreme for guests

    hi having trouble setting my airport extreme for guests?

    Please see your other post on exactly the same subject.

  • I am using an Airport Extreme for wireless and a Netgear VPN Switch for wired connections.  How do I get the two networks to connect?

    I am using an Airport Extreme for wireless and also have a Netgear VPN Switch (FV5318) for internal wired ethernet connections.  How do I get the two networks to connect to each other?

    Tesserax, I would like to keep the Airport Extreme in nplace before the Netgear FVS318 switch because I am using all of the 8 ethernet outputs distributed to 8 differerent locationsl  This way I can just use one of the LAN outputs from the Airport to feed the FVS318.  Here is what I think I am hearing you say:
    Tne reason why the wired and wireless devices are not communicating is because the FVS318G is also a DHCP server and in conflict with the AEBS.
    To remedy the situastion here is probably what I need to do in order:
    1. Change the LAN IP Address of the Netgear FVS318G to be the same subnet of the Airport Extreme.
    2. Then, disable the Netgear FVS318G as a DHCP server.
    3. Make sure the ethernet cable from the LAN port of the Airport Extreme connectis to the LAN port of the Netgear FVS318G.
    4. Restart everything.
    Can you provide me the steps I need to take to get the right IP addresses from the Airport Extreme to put into the Netgear to fix the conflict?  I have the Airport Utility.  I also have two airport express hot spots, and two Apple TVs in addition to computers attached to the 8 ethernet lines.
    Thank you.
    Steve

  • How to Set Up AirPort Extreme 802.11n only Network

    I purchased a used AirPort Extreme base station and a used AirPort Express off eBay to upgrade my home network. Both are the latest model AE (dual band II, firmware 7.5.1) and AX (802.11n, firmware 7.4.2). I want to use my AE as main router (Internet connection, DHCP) and use my AX to wirelessly extend network to my family room, where I have my Xbox accepting only wired network. And I want AE and AX to communicate through 802.11n to maximize bandwidth. Sounds easy right?
    Well, I've got this set up mostly working except the 802.11n part. Not matter what I do, It seems only operating in g mode. I made my AE creating a 5Ghz network but I couldn't find this network anywhere. Not on my iPad, not on my iMac.
    I'm wondering if I have a defective AE. The seller on eBay told me he used the 11n network just fine. The router is still under warranty, I'm wondering if I should ask Apple for a repair? But since I'm pretty new to Mac in general, I figure there might be something I just missed and hence this post. Any help is greatly appreciated!
    Some screenshots of my configuration: http://picasaweb.google.com/xianxu/IPad

    I do have an AX that extends the AE network. There is nowhere on AX that I can specify radio mode, once I specified it to extend a network. I assume AX talks to AE over the n network and then extends the network to be g compatible? Sounds really strange.
    Maybe not too strange. Since the AX is a single-band device, it can only extend the AEBSn's 2.4 or 5 GH radio, at a time, not both simultaneously. Since your iPhone was able to connect, most likely, it was extending the 2.4 GHz radio ... which was also configured to support "g" devices. What I haven't figured out is how, if you set the AEBSn's Radio Mode to "n only" why non-"n" are still able to connect when the network is extended.
    ... I chose to create a different network name for 5Ghz radio as something like: MID-EARTH (5 GHz). However I can't seem to find this network anywhere. I'm wondering why this is the case? Is my AE somewhat defective?
    This may be a completely different issue than the extended network one. If you remove the AX from the network equation, wireless clients should see two different Network Names or SSIDs ... one being "MID-EARTH (5 GHz)" and whatever you called the 2.4 GHz network. That is, assuming that the client is capable of accessing both bands. If this is not the case, we would need to revisit your AEBSn's configuration settings.

  • Airport Extreme 802.11ac and USB disk failure

    hi,
    Had an Airport Extreme 5th gen with a USB disk attached for over a year of which my Mac was using Time Machine and creating backups no problem, didnt skip a beat.
    Just bought a new Airport Extreme 802.11ac, attached the same USB disk and Time Machine works once or twice then fails saying it cant find the disk. True enough if I open finder and try and find the disk its not listed.
    Opening the airport utility it shows the disk attached. If I reboot the Airport Extreme the disk shows up again in finder for a short period of time.
    Looks like they released a firmware update 7.7.1 which was supposed to fix this but it seems in my case it hasnt. Even factory reset after the update but no joy.
    Normal wireless activities like internet access etc are fine.
    Not sure if anyone else has experienced this yet? If not I guess ill try a non self powered disk or something, either that my AE is faulty.
    thanks
    matt

    My experience with the 802.11ac extreme with 7.7.1 firmware suggests Time Machine doesn't work when the name assigned to the device (not the SSID) contains a period, which the out-of-the-box name does.
    Out-of-the-box, with the default device name still assigned, I could not get Time Machine to recognize the remote disk on multiple 10.8.4 Macs until I created an empty folder on it. Yet once registered with Time Machine, backups never occurred to the disk--TM status was always "waiting". The server name displayed in TM had the period in "802.11ac" escaped with a backslash (i.e., "802\.11ac").
    I renamed the extreme, but used a name that still contained a period. The same difficulty was encountered registering the disk with TM. Once registered, TM status for the disk was still "waiting".The server name again had the period escaped with a backslash.
    Finally, I just removed the period from the name. Registering the disk with TM then occurred normally and backup began immediately.
    (In an earlier case with the 7.7.0 firmware, I had no trouble registering and backing up to an 802.11ac Time Capsule that had previously been given a name without a period in it.)

  • How to set up Airport Extreme in a Hotel?

    Hi guys,
    i'm living in a hotel for about a month or so and i don't like the hotel's wireless internet (it's at a Hilton Garden Inn) so i decided to buy this Airport Extreme so i could have a better connection. I like to play xbox 360 also and the lag on the games kills me. Any type of help would help me, as i am not tech savvy. What i'm really getting at is that i want to use my Airport extreme as the place where i get my internet from and where i can play xbox on if that makes any sense?

    Tesserax has you on the right path.
    IF...the hotel is trying to charge you for each device that connects, you could try changing the Connection Sharing setting to "Share a public IP address". You'll need to click "ignore" to the warning that you will likely receive about a Double NAT on the network.
    If you are playing games online, the console will probably not like the Double NAT setting at all. But, it's worth a try if the Bridge Mode setting wants to charge for each separate device that connects.

  • Can I set up Airport Extreme for wireless printiing over Uverse network?

    I previously had DSL, and used my Airport Extreme as my wireless router. It was in my home office, so my printer was directly plugged into the Base Station. I recently switched to ATT Uverse, which came with its own wireless router. The new router is in another room, next to the TV. My question is this: Can I set up my old AEBS to function as a wireless printing outpost, like an Airport Express, that would be connected to my office printer but accessed through the ATT network? Thanks.

    Welcome to the discussions, Patrick!
    Can I set up my old AEBS to function as a wireless printing outpost, like an Airport Express, that would be connected to my office printer but accessed through the ATT network?
    In theory, yes. In practice, this is one of those things that you won't know until you try. Since the AEBS will have to "join" your ATT wireless network, the biggest question will be whether or not you can find a matching security setting on the AEBS for the ATT wireless network.
    Are you able to get into the setup pages on the ATT router to see exactly what type of security is being used? Ideally, it will be WPA2 Personal, but different manufacturers use different names and flavors for the same thing, so it's rarely as easy as one might hope when you try to get devices from two manufacturers to talk to each other over wireless.

  • HT2305 How do I download Airport Extreme for a PC?

    How do I download the AIrport Extreme Utility for a PC on Windows 7?

    Click the link below
    AirPort Utility 5.6.1 for Windows

  • Setting Up AirPort Extreme for Static IP

    We purchased a new AirPort Extreme about a month ago.  It was very easy to set up and worked very well for all of the devices in our home, with the exception of VPN connections on our work laptops.  These were incredibly slow (taking 20-30 minutes to open large spreadsheets, etc.).  We talked to our ISP (4G satellite connection) about this, and they recommended going to a static IP.  I have used the AirPort Utility to enter the IP address, sub net mass, router address and DNS numbers, and the AirPort indicates everything is set up properly (green status light, no errors in AirPort Utility), but it will no connect.  Looking at the Internet Connection through AirPort Utility, it has all the correct numbers but the connection says "disconnected".  I am able to establish an ethernet connection directly from the modem to a computer and connect with no issues.  And the ISP has confirmed that the modem is working properly.
    What am I missing to get the connection throughb to my AirPort Extreme?
    Thanks for any help and suggestions you can provide.

    Hi..
    I have this same question.
    Yes i did change all those and have tried with all the possible settings.
    Still the problem persists..It shows all the configuration and all is right and still it is not connecting to internet.
    Cross checked with the ISP, Tried same configuration in the mac machine(It's working) everything else seems to be fine but only the Airport is not connecting to the Internet.
    Any solution or clarification will be appreciated.
    Thanks in Advance.

  • Setting up airport Extreme for Remote Printing

    I'm leaving town and need to be able to print to our work printer (HP LJ 1320 connected via Ethernet to AirPort Extreme 802.11n).
    I also want to set up our home printer (HP LJ 1022 connected to Time Capsule via USB).
    I've spent hours trying everything I can think of - changed AirPort settings, have desktops sharing printers - nothing works.
    I have no problem connecting to computers over the internet - using screen sharing with ease. I am at a loss as to why printing is such a problem. any help will be hugely appreciated!

    I did open those ports on my AirPorts.
    I've tried setting up the printers as LPD and IPP as well as HP JetDirect - Socket, but despite pointing my print jobs at these, nothing has worked yet.
    Is the Airport going to act as a print server - or is that just part of the printer? Is a server even necessary? It isn't when I'm on site with either printer.
    good luck with your set-up. thanks for your input.

Maybe you are looking for