How to set up an old AP Express

Denne versjonen av AirPort-verktøy støtter ikke denne basestasjonen. Bruk AirPort Utility 5.6 til å konfigurere eller administrere denne basestasjonen. AirPort Utility 5.6 er tilgjengelig på AirPort service og support.
" This version of AP-Utility does not support this Base station. Use AP-Utility 5.6 to configure this unit.
When I try to install this (5.6) on my Mac (10.8.2) i won't let me...
Any ideas how to acsess my Airport ???

To add some information..
I'm currentliy running the AP-U 6.1 and that is when i get this message..
I have tried tu Unistall AP-U, but my Mac won't let me.
Anyone ??

Similar Messages

How to set up and configure AirPort Express for AirPlay and iTunes

Saw somewhere that supposedly there were some apple written guidlines on the above topic. I have searched all over for them. Anyone know where I can get a copy to read through. Just trying to educate myself a bit and sety up another room with access to itunes, radio, etc with high quality speakers and amp off my express.

Here you go ...
How to set up and configure AirPort Express for AirPlay and iTunes

HT1515 How do i get my old AirPort Express (7years old) to work with my new Time Capsule?

How do i get my old AirPort Express (7years old) to work with my new Time Capsule?

Does anyone at Apple have help for this sort of question - I too have an old printer (HP LaserJet 5MP) that I would like to keep using on my Mac. (Mac OSX 10.6.8).
I got it working by getting a USB cord that connects to it - but every once in a while it just stops working for weeks. The mac 'sees' it and it sends the data because the printer lights start blinking but then it just doesn't do anything. Is there no one who can tell me (and raterada) how to get some new life into these old printers. I would rather not add this (and a new toner cart) to the landfill just yet. . .

Airport Utility 5.6 is not supported in Mavericks. How do I access my old Airport Express?

I have an old Airport Express streaming iTunes to a Bose Wave Radio. I wanted to change the name, but it requires Airport Utility 5.6 and that isn't supported by Mavericks. How do I access my old airport express with a computer on OSX 9?

Yes, if you are running Tiger 10.4.x and have AirPort Utility 5.4.2 installed.
AirPort Utility 5.4.2 for Mac - Support - Apple

How can I use my old AirPort Express?

How can I use my old AirPort Express (the one that plugs right into the wall without a power cable) to stream music to a stereo when I am using the new Airport Express? The AirPort Utility 6.1 will not recognize the old AirPort Express.

Apple does not make it easy for you to use an older device when they want you to buy newer devices.
See this link for tips on how to install a version of AirPort Utility on Mountain Lion that will allow you to configure your older Express:
http://www.macworld.com/article/1167965/mountain_lion_and_the_ancient_airport_ba se_station.html
This is not supported by Apple, so it is your decision on whether you want to move forward with this. It works fine for me, but I cannot guarantee that it will work for you, nor offer support if you have difficulty.

How can i change my old airport express password with mavericks

I just bought a new TV and I am trying to connect to my wi-fi, which runs via an old Airport Express. The TV manufacturer says that I should try changing my password from a WEP to WPA - but it seems that I can't even access my Airport Express because it's not supported by Mavericks. Is there a work-around, or do I need to upgrade my Airport Express? It's running fine otherwise - supports multiple laptops and iPhone.

Hi green jean
Try this > http://www.apple.com/airportextreme/features/printing.html
but also see > http://docs.info.apple.com/article.html?artnum=305293
Dennis

How can i use my old airport express with my new imac and wireless hp print

i just bought my first imac (intel) and a wireless hp printer. i now realize that a wireless connection between my imac and my printer needs a router.
i have an airport express base station, which is a few years old. I can't find my documentation, so i don't know its specifications.
how can i find out the specs of the airport express i have and whether i can use it now? it says that it is model a1084 100-240v~ 0.2a 50-60 hz.
does that tell any knowledgeable people out there about the specs? can i search the apple website by serial number and find the specs?
thank all of you potential responders ahead of time.

Hi green jean
Try this > http://www.apple.com/airportextreme/features/printing.html
but also see > http://docs.info.apple.com/article.html?artnum=305293
Dennis

NI_FTPFiles Operation: How to set FilesToFTP--- LocalPath in Pre-Expression?

Hi Guys,
I need to change LocalPath parameter in NI_FTPFiles, but I don't know how to write the correct expression.
I can set it like:
RunState.Sequence.Main["FTP Files"].FilesToFTP.ArrayElementPrototype.LocalPath = "c:\\myfolder\\newfile.txt"
But it is wrong.
Any one can help me? Thanks very much!

Try using Step.FilesToFTP[0].LocalPath = "c:\\myfolder\\newfile.txt". Instead of 0 you could use a numeric variable.
It's the proper way to use it in that step anyway.
BTW- The reason yours won't work is because FilesToFTP is an array and has to be indexed.
jigg
CTA, CLA
teststandhelp.com
~Will work for kudos and/or BBQ~

Is it possible to set up my old airport express to my macbook pro?

I have an airport express base station that i used back when I used an ibook G4. Can I still use this airport for my macbook pro?
I tried installing and setting up but got a message that Power PC applications are no longer supported.

Forget about the CD, it will not be useful.
Use the workaround described in this thread: How do I configure an Airport Express when I get this message in Airport Utility? "This version of AirPort Utility doesn’t support this base station."
Pay attention to the caveat in the final paragraph, restated here for emphasis:
Keep in mind that Apple's decision to abandon support for your original AirPort Express was for reasons known only to them. Remember that you are using obsolete equipment, should some future OS X feature not work for you.

Data reading and writing problem? how to set " Read from Measurment File express.vi" 's readout datasize?

Dear all,
I want to use Labview to process a data.
Now I have a array in a text file.
this array is very very big. which is at least row*col = 6 * 100000;
the column size always 6,
but the row size is ramdom, some times is very big, like bigger than 65535,
when I use "read from measurement file express.vi" to read this file, the array I could get always 6*5339, I don't know why. the column size is always 5339.
and then I delete the 1st row of the array and then write into a txt file via "write measurement file express. vi", it takes a very long time. almost computer has no response. after a while, no file was creat to record the data.
is there an efficient way to process such big data file and store the processed file into a new file
thank you very much
Jack
Message Edited by weichengatech on 03-09-2006 12:00 AM

Hello,
There’s no real efficient way to read the file if you don’t
know exactly how many rows of data you have.
Your going to just have to read a row at a time and add the results to
the end of an array (granted for the clever programmers there are some more
efficient ways to do this than just with ‘build array’). I would start by asking you how much
information you know about the file and what the exact structure of it is (i.e.
is it a binary file, a tab delimited file, or a LVM file)? Could you provide a screenshot of the code
you are running? If you provide a little more information on the file structure
we might be able to contribute some additional information.
Look forward to hearing back from you-
Travis M
LabVIEW R&D
National Instruments

How to set NAT Type in Airport Express for PS3

I just replaced my existing WiFi router with a Airport Express, using the same log in information, and all other devices includin iPhone and laptop can get on line w/o problem, but my PS3 can not seems to log in for on-line game, and when I check the internet connection settings, it show NAT type failed due to timeout error. I have read some articles about the need to change NAT Type from 3 to 2 or something like that, how can not find in Airport Utilities on how to open up NAT to change its type? anyone can help? Appreciate.

Unfortunately there are no specific NAT settings on the AirPort routers to change the NAT type. On the AirPorts you either have NAT enabled or disabled. Other options would be to use either a DMZ or open specific ports on the AirPort's NAT firewall to allow your PS3 to gain full access to PS3's on-line gaming service.

How to set keepalive check for regular expression

Hi
We are using css110501 CSS.
Right now the keepalives on services are set using hash values.
But i want to change this keepalives to implement keepalives with regular expression checking.
Any Ideas?

The CSS supports it's own native scripting language that can be used to write keepalives among other things.
Here is an example of a script that I wrote to check a page for some specific text:
! Filename: ap-kal-statpage
! Parameters: None - must be coded in script
! Description:
! This script will attempt to connect to a host and
! "GET" an html page. The script checks the contents
! of the page for a particular string. If the string
! is found, the script passes.
! Failure Upon:
! 1. The correct arguments are not supplied.
! 2. The CSS is unable to connect to the host.
! 3. The string is not found in the page.
no echo
if ${ARGS}[#] "LT" "4"
echo "Usage: ap-kal-portlist \'Hostname Port Page String ...\'"
exit script 1
endbranch
set host "${ARGS}[1]"
set port "${ARGS}[2]"
set page "${ARGS}[3]"
set string "${ARGS}[4]"
set EXIT_MSG "Host ${host} not responding on TCP port ${port}."
socket connect host ${host} port ${port} tcp
socket send ${SOCKET} "GET ${page} HTTP/1.0\n\n"
set EXIT_MSG "String was not found."
socket waitfor ${SOCKET} "${string}" 200
socket disconnect ${SOCKET}
echo "String ${string} was found."
no set EXIT_MSG
exit script 0

If i have updated to os 10.7.5 how can i manage my old airport express?

when i go to the wi-fi, and click on "airport express" it tells me i need to use airport utility 5.6 to manage, but 5.6 doesn't work on 10.7.5?

Find an alternative, or return to Snow Leopard, either directly or by running Mac OS X 10.6 Server inside a product such as VirtualBox, Parallels Desktop, or VMware Fusion.
(127049)

Can't find how to set up wires modem, Airport Express, imac

My imac gets its internet using ethernet cable from cable modem (only one ethernet port out of it) to imac. Just bought airport express to send wireless signal to my house so kids can use wireless pc laptop. But want to keep my imac hard wired to internet. What cables do I need to plug in where?

If your new AirPort Express is a 2nd generation model, then you would just need another Ethernet cable and connect it between the base station's LAN (opposing arrows) port and your iMac.

How do I reset my old iPad 2 becoming a new iPad again?

Hi,
I am passing my iPad 2 to my dad, and before I do so...
I was wondering how do I set up my iPad to become new again?
I don't want to have all my applications etc, in this iPad before I hand it over to my dad. So I was wondering how to set up an old ipad to become new again?
Thanks for the help!

Settings>General>Reset>Erase all content and settings

How to set up an old AP Express

Similar Messages

Maybe you are looking for