How to set up guest wifi network on 1200 series APs with disclaimer web portal?

I've been thinking about this one for awhile. I want to set up a guest wifi network without any security (AES / TKIP) that allows guests to connect. Ideally, their web browser would be redirected to a web portal containing legal disclaimers, and they would need to accept the terms and conditions to use the guest wifi. I would also like to have them be required to visit the web portal again every 8 hours after that to accept the terms and conditions again.
I have a Cisco 1240AG access point already. What else do I need to make this work?

I don't believe you can do this just with an AP running in autonomous mode you would need to have a WLC to configure the splash page.
Have a look here:
http://www.cisco.com/c/en/us/td/docs/wireless/controller/7-0/configuration/guide/c70/c70users.html#wp1049273
Alternatively you can use software running on a PC/Server. Something like http://www.antamedia.com/hotspot/
Hope that helps!
Matty

Similar Messages

How would I contain guest Wifi network in firewall?

I would like to implement a guest wifi network on my preexisting private network and can't figure out the security on my firewall. Currently the link connecting my private network to the internet is functioning fine and I really don't want to change this link into a trunk as I believe trying to reconfigure the trunk and security lists in the firewall would cause downtime. I would like to use a second interface on the firewall (5520 ASA with 8.2 software) as a trunk interface for my guest network and any other new VLAN in the future. My main concern is at the Core of my network the default gateway is the private IP for my internal firewall connection. If the guest network is connected to my core device going to the ASA, how do I specify a second default gateway on the core for the guest network on the ASA?
After writing this I realized, what if i connected a switch directly to the second trunk interface on my ASA and then used this IP as the default gateway for the guest network? I believe this should work but this leads me to one more question:
Say I wanted to allow my quest network access to a specific server on my internal network, would a proper configuration be to setup the ACLs on the firewall, allowing them to communicate to my inside network?

Hi,
Yeah I suppose changing the existing interface to a Trunk would not be possible without somekind of downtime unless you used an untypical configuration.
Sadly, my personal knowledge of wireless networks and the devices is almost nonexistent as we have different people to handle setting up those.
But I would imagine you can use a separate Vlan for the Guest Wifi and bring that Vlan to the new ASA interface only. If your actual core switch is doing routing, in other words if its acting as a L3 switch then you should probably add the Guest Wifi Vlan only as L2 to the core switch and configure it all the way to the new ASA Trunk. Default gateway as you say would be the IP address configured on the ASA itself.
Controlling the traffic from the new interface on the ASA should be pretty simple.
access-list GUEST-WIFI remark Allow traffic to internal server
access-list GUEST-WIFI permit tcp host eq
access-list GUEST-WIFI remark Deny All traffic to Internal networks
access-list GUEST-WIFI deny ip any
access-list GUEST-WIFI remark Allow All other traffic
access-list GUEST-WIFI permit ip any
access-group GUEST-WIFI in interface
The above ACL first allows some traffic to a certain internal server with a certain service. It then blocks all other traffic to the internal network. Finally it allows all other traffic. That would be all traffic destined to external public networks.
Naturally you would need possibly Static Identity NAT configurations (since you are using 8.2 software) to enable connections from the Guest Wifi to Internal network.
- Jouni

Internet sharing via dongle, how to set password for wifi network created?

I am using a USB dongle with my Mac book Pro to share internet through AirPort, so that i can access my mac book's wifi from my iphone. This works great, but it is an open network and I woud like to set up a password.
If anyone can point me in the direction I would be very grateful!
Thanks

If you are using OS X's Internet Sharing feature, then you can configure wireless security on your Mac's internal AirPort Card but are limited by the OS X version that you are using. It was not until Mountain Lion that Apple provided WPA2 security. Prior to this only WEP was available.
You configure Internet Sharing via System Preferences > Sharing > Internet Sharing. (I don't have 10.6.x on any of my Macs so this may be different for your case.) Once you configure what is shared, you can then add wireless encryption.

How can I set up a guest WiFi network using Time Capsule and Airport Express extension?

How can I set up a guest WiFi network using Time Capsule and Airport Express extension?

Sorry, but it is not possible to "extend" the Guest Network using either wireless or an Ethernet connection.

A tech company just set up a wifi network in my house and does not use my existing TC; how do I get it in the network to serve as backup for my iMac? (I don't need it as a wifi access point anymore)

a tech company just set up a wifi network in my house and does not use my existing TC; how do I get it in the network to serve as backup for my iMac? (I don't need it as a wifi access point anymore) thanks

Just bridge the TC and plug it by ethernet into the main router.
Bridge in v5 airport utility.
In v6 it is under network.. change it from DHCP and NAT to Off bridge mode.
Turn off the wireless.

How to set up Guest Network, while Airport Extreme is connected to Satellite Receiver

How to set up Guest Network, while Airport Extreme is connected to Satellite Receiver?

Depending on how you have your AirPort Extreme configured to work with the satellite receiver, it may or may not be possible to enable the Guest Network function.
We will need to check some settings on your Mac or PC, but in order to do that, we need to know what operating system you are using on your computer.
If you have a Mac, click the Apple icon in the upper left corner of the computer screen, then click About This Mac. Post back with the OS X Version number that you see there.

How-do-i-configure-guest-wifi-access-using-2504-wlc-fortigate-utm-l3-device

Dear All
I have a 2504 Wireless Controller with multiple radios attached. I currently have a "private" WLAN configured (taking ip from windows server based DHCP of Range 192.1681.0/24 ) and working, but I need to add a Guest/Public WLAN which should take the IP from Other DHCP Configured on Fortigate UTM of range 172.16.0.0/24.
We have one SG300 switch in the office and the rest are basic switches.
Our firewall/router is a Fortigate UTM 240D
Find the attached network diagram for the issue.
Is there a SIMPLE way to enabling guest access that doesn't require VLANS (or are VLANS easier than I'm making them)?
Thanks.
- See more at: https://supportforums.cisco.com/discussion/12473186/how-do-i-configure-guest-wifi-access-using-2504-wlc-fortigate-utm-l3-device#sthash.aj1XcWI0.dpuf

Complete these steps in order to configure the devices for this network setup:
http://www.cisco.com/c/en/us/support/docs/wireless-mobility/wireless-vlan/70937-guest-internal-wlan.html
Configure Dynamic Interfaces on the WLC for the Guest and Internal Users
Create WLANs for the Guest and Internal Users
Configure the Layer 2 Switch Port that Connects to the WLC as Trunk Port

How can I create a wifi network

I have created a wifi network, and also connected with my ipad, but it does not work, just connect. what I should do?

search the Internet. https://www.google.com/search?q=how+to+set+up+a+wifi+network

How can i delete a wifi network?

how can i delete a wifi network?

deroco wrote:
Thank you but I tried that and it still shows up as a network. I live out in the country and shouldn't have any other networks close. I am afraid of a security breach.
As far as networks showing up when you right click the WiFi icon in the Menu Bar, you will always see those that are close by. I know of no way to hide or remove those.
What leroydouglas provided is correct to remove any WiFi networks you have previously connected to.

How do i find the wifi network and password for iphone 4s

how do i find the wifi network name and passwordfor iphone 4s?

Well Netgear will not know your password. The factory default user name for netgear is usually admin and the factory default is password is password. Go to an internet browser and in the url windo type in 192.168.0.1 and if I am right a login window will appear. Try the factory defaults.

How to set wireless printer at ad Hoc mode in CP1025nw with auto-off is off?? ie never auto-off!!

How to set wireless printer at ad Hoc mode in CP1025nw with auto-off is off?? ie never auto-off!!
Thank you very much for your help if any!!
This question was solved.
View Solution.

Quite a few questions there, Sends, but I will do what I can to answer them.
I would first recommend buying a router, even if it is one that you won't connect to the internet and network this with your other PCs and the printer. This will give you the best functionality and results for what you are attempting to do.
Additionally, the Auto Off feature of the printer can be disabled, and is not affected by the connection type. You can usually go through the Setup Menu and select Tools to change the options there on the energy saving features.
Lastly, the auto off feature on your computer is a Windows question, but an easy one to answer. If you are on a laptop you can right-click on the battery in the service tray (bottom right hand corner) and change the energy conservation settings.
You might be better off installing the printer through the USB cord and alternating that based on when you are using it, but that would be optimal only if you are printing only a few documents on an irregular basis. A networked connection is the easiest to manage over several computers, honesty, but you do have some requirements for that connection and limitations as well.
I hope this information is useful!

How do I set up my airport express to make a connection with my Hp? I already have it set up for my mac laptop just not sure how to set it up so that theres also a connection with my Hp

how do I set up my airport to make a connection with my Hp? I already have it set up for my mac laptop just not sure how to set it up so that theres also a connection with my Hp

I set up my new HP Descjet 3054A . I had a problem becouse Apple give me CD as a driver. The thing was that CD wasn good for this printer becouse it was old software:) I had to go to Apple store so the specialist had to download me he wright driver. Becouse I didnt wannet to screw this up . When he downloaded driver I fired it up at house and thingworks perfect. The thing is when you download all the software from HP side . Then you have to connect your MAC to printer via USB . Fallow the instructions it should works. Worked for me. Good Luck!

How to set the transition duration of a slide in keynote with applescript

hi
how to set the transition duration of a slide in keynote with applescript
i made an applescript script which converts a numbers file to a keynote presentation
figured out how to set the transitions but cant find how to set the time
+set appTransition of slideTransition of current slide to "apple:dissolve"+
anyone?

you can send keystrokes to invoke menu commands via shortcuts but as for transition time not sure. You've check the dictionary right? Scripting support is very limited in KN.

Time Capsule set up and wifi network OK but MacBook doesn't see capsule as airport device. Do I need to do a hard reset and start again?

I recently bought a Time Capsule and sucessfully set it up in accordance with the instruction book. The home network and guest network seem to work fine but my MacBook cannot find the Time Capsule wirelessley.
Initially I set up the time capsule connected to the MacBook with an ethernet cable. The Time Machine got 30GB way through a 60GB initial back up and then stopped for no obvious reason. Since then the capsule has not been visible to the MacBook. I have tried to reconfigure through Airport Utility but even after reperated rescans the capsule remains invisible.
Any help would be extremely welcome.

1. i would restore the express to factory defaut by holding the reset button on the unit with a paperclip while you are powering it on
2. if it restored, you should be able to see it in your wifi icon at top of screen as "airport express"
or you can see it in airport utility
3. then if you want to connect it wirelessly to your time capsule, you would choose "extend network" and put in relevant security and password....this would make the express a wireless access point, fed by your time capsule(main router)
if you chose to do it wired which is a better way if you have access to ethernet port at wall, you would choose "create a wireless network" and then under the "network" tab you would choose "Bridge Mode".....this would make the express a wired access point, fed by your time capsule(main router)

HT204051 Can you set a default WiFi network? Or is it possible to remove a near field WiFi network?

I want to set a default a default network to connect via wifi . Is it possible to automatically connect when in range?

Hi GymJockey67,
Thanks for your question. The resource below explains how to set your preferred Wi-Fi network as the default connection.
OS X Yosemite: Choose preferred wireless networks
https://support.apple.com/kb/PH18525?locale=en_US
Cheers,
Judy

How to set up guest wifi network on 1200 series APs with disclaimer web portal?

Similar Messages

Maybe you are looking for