How to set up load balancing with overload server on css

can anyone tell me how to set up a load balancing config on css that will enable me to LB proxy caches and when they have too many connections then LB against an overload proxy-cache.
Such that when the normal proxy-cache farm is under the ceiling of max connections then the overload server is not used ?
I don't think redirect or sorry server will do this ?

see the below configuration,any question,just tell me.
service proxy-1
! below is the real ip of server
ip address 10.1.1.1
keepalive type icmp
active
service proxy-2
ip address 10.1.1.2
keepalive type icmp
active
! enter owner config-mode
owner proxy
! define a content rule,match what you want to load balancing
content rule-proxy
! below is virtual ip,it can be another ip segment
vip address 10.1.1.50
add service proxy-1
add service proxy-2
protocol any
advanced-balance sticky-srcip
active

Similar Messages

T3 Load Balancing with Weblogic Server 6.1

We are using rwo weblogic 6.1 servers A and B behind a load balancer with a DNS name (eg. www.loadbalancer.com). We are using T3 for Java client to application server communication. The client creates the Initial context with the load balancer url,creates remote objects using the context, closes the initial context and then tries to get a new initial Context. What we noticed is even though the client closes the first context and gets a new one, the client is always hooked on to only one server making load balancing ineffective. Is there a T3 configuration to release the connection when we close the context ? The documentation says only one T3 is established per client JVM.

Rick,
You may want to look at the Alteon and F5 configuration we have on edocs.
Take a look at the following URLs for a possible solution
http://edocs.bea.com/wls/docs61/cluster/alteon.html#591902
http://edocs.bea.com/wls/docs61/cluster/bigip.html#591902
Chuck Nelson
DRE
BEA Technical Support

CSS Load Balancing with Billing Server

Hi Gilles
Could I have a CSS load balancing two servers and also have it communicate with a billing server across the network. If yes then how can I do it?
Regards,
Sushil

the CSS does not have the notion of billing server. A separate device - like the CSG - should be used if you need to collect billing info.
Gilles.

HTTP Tunneling and Load Balancing with Weblogic Server 6.1

We use T3 for Java client to application server communication (Weblogic Server
6.1) and keep the session open for the life of the client. We many customers
using this with load balancers and all works fine. We have just started to use
BEA's HTTP tunneling and I have a question concerning how this will work with
load balancers. Since the single T3 connection has been replaced with a series
of stateless HTTP connections, does the BEA tunneling code put session information
in the HTTP header? If so, what information does it place in the header. If
it does we should be able to use that to make sure that the load balancer always
sends HTTP requests with that session to the same application server.
Thanks!
Rick

Rick,
You may want to look at the Alteon and F5 configuration we have on edocs.
Take a look at the following URLs for a possible solution
http://edocs.bea.com/wls/docs61/cluster/alteon.html#591902
http://edocs.bea.com/wls/docs61/cluster/bigip.html#591902
Chuck Nelson
DRE
BEA Technical Support

Load Balancing with forms server 10g

Hello,
i've a cliente which is right now processing a migration from a client-server 6i platform (using Terminal Servers) to a forms 10g web platform with several Application Servers 10g in standalone.
At the end, client want to enable Load Balancing in order to have some manage at each Application Server load.
The idea to accomplish is to have an hardware Load Balancer. The client already has a CISCO CSS 11503 SSL.
Is there any documentation where i can check more info about the compatibility/configuration to this architecture.
Thanks for your attention.
regards,
Pedro Ribeiro

You can check this doc Link:[http://download.oracle.com/docs/cd/B14099_19/hpux.1012/install.1012/install/toc.htm]
It say all about it, and don't mention nothing about a Load Balancer, but I'll try tokeep searching.
Greetings.

How does load-balancing with WebCache work - is there still a bottleneck?

Hello,
We're migrating an old Forms 6i app to 10.1.2.0.2 (apps servers = Redhat Linux), and are starting to consider using WebCache to loadbalance between two application servers.
My question is this - say we have apps servers A and B, both running Forms and Reports Services. We use Webcache on server A (don't have the luxury of a third apps server...) to load balance between A and B. So all initial requests come into A, which in some cases may then be diverted to start a new Forms session on B.
For those users whose middle-tier sessions are now running on B - will all network traffic for their Forms session continue to be routed through Webcache on A, then to B, over the course of the session? Or does Webcache somehow shunt the whole connection to be straight between the client PC and server B, for the duration of that Forms session?
If the former, does that mean that the server hosting Webcache can still be a significant bottleneck for network traffic? Have people found load-balancing with Webcache to be useful..?
Thanks in advance,
James

Hi gudnyc,
Thanks for posting on Adobe forums.
For HDPI you do not have to do any It will adjust automatically.
http://helpx.adobe.com/photoshop-elements/using/whats-new.html
Regards,
Sandeep

Issue in setting Load balancing for Indesign Server CS5.5

Hi All,
I need to set up load balancing mechanism for Indesign Server CS5.5 on Windows Server 2008 R2(64 bit version).
I have dutifully following all steps defined in "WORKING WITH LOAD BALANCING AND QUEUEING FOR ADOBE INDESIGN CS5 SERVER.pdf"
After running Indesign server using batch file "startup-indesign-server-CORBA-4instances.bat" from "<ID_SDK>\samples\load-balancing-and-queuing-clients\indesignserver-startup-scripts", I get only one instance of Indesign Server running. How to run multiple instances of the INDD server ? Is running multiple instance has something to do with type of licensing ?
Now I run Clover.cmd script, I get this screen. I have no idea why its not working. Please help. Please let me know, if the scenario is not clear and more information is required.
Thnx,
D

This is the image after running clover.bat

Load balancing with JSP

Anyone and everyone,
When configuring load balancing with Weblogic clusters, does load
balancing take effect for all services or just EJB and RMI? Or another
way of saying the same thing, can I setup weighted load balancing for
the JSP engines across 2 weblogic servers.
Thanks in advance,
Mike

The load-balancing documentation you read describing the different algorithms only applies to RMI stubs (e.g., EJB clients). Please see http://www.weblogic.com/docs51/cluster/concepts.html#1026091 for a description of how load-balancing/clustering works with servlets/JSPs.
The short answer is that in using servlet clustering, most people want/need/use in-memory replication for HttpSession objects. In WLS 5.1 (and before), in-memory replication requires one or more proxy servers be set-up in front of the cluster. Typically, most people use something like BigIP to load-balance
across the proxy servers and let the weblogic plug-in for the proxy server handle the routing to the cluster. The plug-in uses round-robin until an HttpSession is established for a user, then it always tries to route to the server where the user's session is located.
Hope this helps,
Robert
Brian Lin wrote:
All,
I have a quesiton here regarding load balancing with DNS round robin. As of Chapter Adminstration of Clustering Weblogic server, Weblogic can be configured to balance by weight. How about Weblogic handle weight based balancing after DNS round robin ip response? or just can choose one way instead of both?
What's the big difference between choosing BigIP and software balancing (WL)?
Brian
"Wei Guan" <[email protected]> wrote:
I don't think you can configure this load balancing in weblogic in current
release. However, if you have Big-IP or LocalDireoctr, you can set up
weighted load-balancing there. Otherwise, weblogic proxy will use DNS round
robin to do the load-balancing between JSP engins.
My 2 cents.
Cheers - Wei
Michael Yakimisky <[email protected]> wrote in message
news:[email protected]...
Anyone and everyone,
When configuring load balancing with Weblogic clusters, does load
balancing take effect for all services or just EJB and RMI? Or another
way of saying the same thing, can I setup weighted load balancing for
the JSP engines across 2 weblogic servers.
Thanks in advance,
Mike

CF 10 Load-Balancing with Remote Instances

I was reading an article on Clustering/LB/HA using CF8, but have not found any updates for CF10.
Using VM VirtualBox to setup a few virtual servers, I am looking to setup a load balancing of ColdFusion 10 on 2 remote instances. The goal would be have ColdFusion Cluster Manager be able to point http request to one of the two servers based on load/availability. Not really having a hardware cluster/failover setup, just managing resources on two CF instances instead of a standalone.
The servers are Windows Server 2008 R2 with IIS7.5 and ColdFusion 10 Enterprise on installed on 3 of these machines. Let's call them CF-LBManager, CF-Web1, and CF-Web 2. In the CF Docs, they show the Cluster Manager adding the local CF instance and "if you want" a remote instance. However, this scenario would require the main instance to be running and not fail for it to direct to the other instance.
I am trying to set this up now with CF-LBManager as just a manager of the requests coming in. In the Enterprise Manager >> Instance Manager, the local instance is shown and I add the two remote instances with the correct Remote Port, JVM Route, etc. I also made sure the <Cluster>...</Cluster> block was added to the two remote instances (CF-Web1 and CF-Web2) \runtime\conf\server.xml file too, Jetty Services also is running. Now under the Enterprise Manager >> Cluster Manager I add the two remote instances to the cluster, not the local instance on CF-LBManager with Multicast Port and Sticky Sessions enabled. On Submit, I get a green message "You must restart all the server instances and any configured webservers for these changes to take effect.". I go ahead and reboot the servers and come back.
I now browse to the ColdFusion page as a test on CF-Web1 and CF-Web2 to make sure CF is running properly, they do. I then browse the IP of the CF-LBManager, however it only returns the local IIS web site and not redirect to one of the two cluster members. I am not seeing any message on the coldfusion-out.log on the remote instances. Am I not setting this up correctly or not enabling the Cluster Manager to take over and pass along the requests to those in the cluster?

Unfortunatley I don't have a lot of experience with CF10 on Windows, but if you are running CF behind IIS I think you will need to update the Tomcat connector configuraiton to do load balancing. I'm not sure if re-running the wsconfig tool on all of the servers will do this or not, but that is what I would suggest trying first. If that doesn't work you will need to update the Tomcat connector configuraiton manually. You can find more information on load balancing with the Tomcat connector here: http://tomcat.apache.org/connectors-doc/generic_howto/loadbalancers.html.

CSS Load Balancing with Cookies

We are trying to load balance 2 backend servers hosted on Websphere with advance balance cookies method.
Restrictions
ServerA is unable to accept cookies generated from ServerB.
ServerA and ServerB are generating random cookies
Unable to modify cookie string with a constant.
How can we load balance based on cookies considering the above restrictions?
We have attempted to do hash based load balancing with cookies but the problem we run into is the servers do not accept cookies generated from another server.
The configuration we tried is written below:
service ServerA
ip address 192.168.10.2
keepalive type tcp
keepalive port 80
active
service ServerB
ip address 192.168.20.2
keepalive type tcp
keepalive port 80
active
content ABC
url "/*"
add service ServerA
string prefix "JSESSIONID="
advanced-balance cookies
port 80
add service ServerB
string skip-length 5
string process-length 16
string operation hash-xor
protocol tcp
vip address 172.16.32.1
active
Can we change the string prefix to JSESSION instead of JSESSIONID= ?
The only place the app guys can add a constant string to match on is before the = sign.
Is it possible for CSS to match on a constant string before = sign e.g below:
service ServerA
ip address 192.168.10.2
keepalive type tcp
keepalive port 80
string id567=
active
service ServerB
ip address 192.168.20.2
keepalive type tcp
keepalive port 80
string id123=
active
content ABC
url "/*"
add service ServerA
string prefix "JSESSION"
advanced-balance cookies
port 80
add service ServerB
string skip-length 0
string process-length 6
protocol tcp
vip address 172.16.32.1
active

It should work.
There is no reason for it not to work...
This is the best method you can have on the CSS for stickyness.
Get a sniffer trace on the client and server with arrowpoint cookie configured on the CSS and capture a failure so we can see what is going on.
also send me the config so I can verify everything is ok.
If you have a service request open with the TAC, you can also give the SR # so I can review what has been done.
Gilles.

Cache and Load Balancing with Oracle APEX Listener

Hi,
I intend to use only HTTP access.
How to implement a Cache and Load Balancing with the Oracle APEX Listener?
Is it possible to do with the the standalone running APEX Listener?
Thanks by advance for any tips/documentation/references.
Kind Regards.

Hi,
I think this question is best asked in the APEX Listener forum:
ORDS, SODA & JSON in the Database
Kind regards
Sandro

Load Balancing with ASR9000 vN and multiple ISPs

Hi,
we will deploy a new DC as Active/Active.
We will have ISPA and ISP B in each DC. Internet users are anybody in the internet coming to our e-commerce DC application.
How could we do load balancing between ISPs using the ASR9001 and nV feature ?
There is any IOS-XR feature that could help us about to do load balancing between ISPs?
Thanks a lot.
Regards,
J

You have 2 options here Jordi, either you can use BGP loadbalancing, this requires multipath as BGP by default would only install one route from the BGP table to the RIB hence FIB.
But this may result in excessive IRL (inter rack link) usage in the cluster when traffic coming in on rack0 wants to take the bGP path out on rack1
You could also use ABF (access-list based forwarding) to forcelly push traffic received on rack0 out on the link on rack0 and use an ipsla tracker to fallback to rack1 in case the uplink is gone.
Alternatively to extend this by IGP signaling to redirect traffic preferably to rack1 to start with to minimize the IRL usage.
And then you also have the ability to use RPL in the uplink path to make one link more preferred on teh internet then the other in case you want to control a bit which link is preferably used on rack0 or rack1
regards
xander

Load balancing with an ASA5510

We have an ASA5510 with two ADSL lines connected and the auto fail-over set up - this is all tested and if the main line fails, the backup line is used in it's place - no problem there.
However, I'd like to increase our connection speed, and one way I've done this in the past is to add a couple of extra ADSL lines to a router that is capable of load balancing.
I'm aware that the ASA5510 does not load balance (seems a waste as we've got the backup line just sitting there doing nothing!), but would it be feasible to add another router in front of the ASA device to perform this load balancing function?
If Yes - any suggestions as to what device I might use?
If No - what would be the issues that would prevent me from doing this?

Thanks for the prompt response Simon
Had a look at the RV016 which seems like it would fit the bill and give us plenty of scope for expansion. I've not set up load balancing on a Cisco before - does it just work (ie auto-detect the connections), or do I need to be aware of licencing etc (as seems to be the case with a lot of cisco features)
With regard to port forwarding, the ASA is already configured and working OK, so I was intending to just push all traffic through to it - my thinkimg being that it's easier to have the config in one place. Is this likely to cause any issues?

IPlanet Load Balancing with BEA Plugin

I'M using a IPlanet Enterprise V.4.1SP9 and use the weblogic load balancing plugin. Furthermore I use 3 weblogic express 6.1 sp2 which receive the requests of the iplanet webserver. my question is how to configure the load balancer plugin (round robin etc.) and if it is possible to get some (debug) output.
I need it because the load balancing doesn't work properly with netscape (althoug it suprisingsly does with the Internet explorer).
Greetings,
Boris

I'M using a IPlanet Enterprise V.4.1SP9 and use the weblogic load balancing plugin. Furthermore I use 3 weblogic express 6.1 sp2 which receive the requests of the iplanet webserver. my question is how to configure the load balancer plugin (round robin etc.) and if it is possible to get some (debug) output.
I need it because the load balancing doesn't work properly with netscape (althoug it suprisingsly does with the Internet explorer).
Greetings,
Boris

Load Balancing with ALBPM 6.0

Hi -
We have had some challenges with load balancing in WebLogic Server 9.2.2 with ALBPM 6.0. We have tried to set the Front End HTTP host and ports on the cluster and individual hosts with no luck. Anyone else have a similar problem?

Hi PR,
Please take a look at the following link:-
http://help.sap.com/SAPHELP_NWPI71/helpdata/EN/28/75153a1a5b4c2de10000000a114084/frameset.htm
"You can only use the SAP message server for HTTP load distribution if
the browser is the direct client of the message server. If another
component lies between the client (browser) and the message server, (for
example, the portal), you cannot use the message server to distribute
the load."
When using the External ITS you could balance the load using the message server and logon groups. In 700 this functionality is not present if there is not a direct connection to the client (Firefox or IE). So you will have to install the webdispatcher to balance the load.
Hope this helps
Michael

How to set up load balancing with overload server on css

Similar Messages

Maybe you are looking for