How to set up my scanner?

I already install the cd in my Mac but still not working. Please help me. Thank you

Hi Jehday14,
Please complete the following steps to enable scanning over a network:
Specifying Your Scanner or Printer
From the Go menu of Finder, select Applications, then double-click the Canon Utilities folder, IJ Network Scanner Selector EX folder, then Canon IJ Network Scanner Selector EX icon. The Canon IJ Network Scanner Selector EX appears in the menu bar, and the Scan-from-PC Settings screen appears.
Select your scanner or printer from Scanners. Select the Bonjour service name set to your scanner or printer. When Bonjour is disabled, the MAC address of your scanner or printer appears.
Click OK.
Setting for Scanning with IJ Scan Utility
Please follow the steps below to set the printer for scanning using the IJ Scan Utility:
Start the IJ Scan Utility.
Select "Canon XXX series Network" (where "XXX" is the model name) for Product Name.
Click Settings... to use another scanner connected to a network.
Click (General Settings), then click Select in Product Name.
The Scan-from-PC Settings screen of IJ Network Scanner Selector EX appears. Select the scanner you want to use and click OK.
In the Settings (General Settings) dialog, click OK. The IJ Scan Utility main screen reappears. You should now be able to scan wirelessly.
Hope this helps!
This didn't answer your question or issue? Please call or email us at one of the methods on the Contact Us page for further assistance.
Did this answer your question? Please click the Accept as Solution button so that others may find the answer as well.

Similar Messages

How to set up a scanner-

hi, i have an epson scanner perfection v500 photo. i've just downloaded its installer (and installed it) but i don't know what to do to run it with photoshop cc…may you help me?
Message was edited by: paolo7862

Hello Shazoreilly,
Thank you for using Apple Support Communities.
I understand that you would like to set up a scanner. The following article on adding or removing a printer should be of assistance. While it refers to printers, it is also applicable to scanners. Specifically see the section on adding a Wi-Fi printer.
OS X Yosemite: Add or remove a printer
Regards,
Jeff D.

Setting up a Scanner

I have two All-In-One Machines on two different wireless networks and had no problem setting up the printers. But, being very new to the Mac (one week), I have no idea how to set up the scanners in them. I used the help function and it said I can either see the scanner (I can't) or set it up like I did the printer. This is not helpful to me as I still can't figure it out.
I have downloaded the printer, scan and the fax software for my Canon 8350 Cdn, but I really don't know what to do to set up the scanner. Any ideas of what I am missing?
I am guessing it is simple, but being so new to the mac I don't know what to do.
I am using the Canon 8350 through the time machine and connected by cat 5 cable, but, no problems with printing at all, just don't know how to set up the scanner.
The other is an HP M2727 through a linksys wireless connected by cat 5 cable.

With regards to the Canon MF8350Cdn, the Canon web site shows that you need to have the application ScanGear v1.20 installed. This will allow you to use Image Capture, which is built in to Mac OS X 10.6, to scan from the document feeder or platen glass. This is not included with 10.6 so you will have to download it if you have not done so already.
With the ScanGear v1.20 installed, the next step would be to add the scanner part of the MF8350. If the device was USB, this is done by opening Print & Fax, clicking + to add a printer and selecting the MF entry that displays as a scanner in the Default view. In the case of a networked MF, I am not sure how you would add this as a scanner. It is possible that it advertises itself on your network as a Bonjour Scanner, in which case it would also appear in the Default browser view. If you don't see it then let me know and I can check with my MF4380dn at work.
Once the scanner has been added to Print & Fax, I would expect that you then have to set the AIO to the scanner mode. With my MF4380dn, which uses the same version of ScanGear as your MF8350, to scan from the copier I have to place the document in the feeder or on the glass and then press the Scan button. This shows Network Scan on the display. If I wanted to scan via USB (which is usually how I have it configured) I have to press the Scan button again so that USB Scan is displayed. I would expect that your MF8350 has a similar function and that you would need to select Network Scan.
With Network Scan set in the MF8350, you can then open Image Capture and you should have the copier showing as one of the devices in the list. You should then be able to select it and then press the Scan button within the application.
I have also noticed that the ScanGear v1.20 adds an application called MF ScanGear. This looks like a similar application to the one the inkjets use and lets you pre-configure actions in response to certain selections, such as scan to file or scan to email. I haven't actually used this application since installing ScanGear (I mainly scan from my MP980 or LiDE 200) so I will have to get back to you about how it all works.
Hope this is enough information for you to get started for now. I will get back to you tomorrow after I get a chance to check the network side of scanning with the MF series.
Pahu
Message was edited by: PAHU

I connected my Canon printer to time capsule, and can print OK. However, I can't get the printer scanner to work. How do you set up the scanner with Time Capsule?

I connected my Canon printer to time capsule, and can print OK. However, I can't get the printer scanner to work. How do you set up the scanner with Time Capsule?

You cannot use USB. It has to be a network capable printer.. is it?? You did not indicate how it is connected.. but by wireless or ethernet then scanning is possible otherwise not.

How to set-up printers in Snow Leopard???

I installed Snow Leopard (10.6) on one of my full backup external La Cie Hard Drives. It took about an hour to install-- and everything seems fine-- I enjoy the slider in windows to get icons to 512 size.
OK BUT how to set-up my ethernet connected Apple LaserWriter 12/640PS (about 1997 vintage) and my Canon Pixma i4000R printers? They work GREAT in Leopard 10.5.8 - but I can't even find them in the Print/Fax System Preference when I start in Snow Leopard. And I don't know where to go nor what to do to find the drivers etc. etc. etc. I choose to install ALL printer drivers when I did the set-up of SL.
It was kinda automatic with 10.5 - but with 10.6 - just nothing. It finds my Canon SCANNER- but no printers...
Thanks for any comments here -- glad I've kept leopard on my internal MacBook HD!
Steve

Stephen Schulte2 wrote:
I installed Snow Leopard (10.6) on one of my full backup external La Cie Hard Drives. It took about an hour to install-- and everything seems fine-- I enjoy the slider in windows to get icons to 512 size.
OK BUT how to set-up my ethernet connected Apple LaserWriter 12/640PS
That's an AppleTalk device. You would need to set it to use TCP/IP via DHCP. See <http://support.apple.com/kb/TA21790?viewlocale=en_US> and similar. Good luck.
(about 1997 vintage) and my Canon Pixma i4000R printers?
Canon released a driver for that device in June this year. I'd see if that fixes your problem, or if it doesn't, I'd contact Canon tech support.
They work GREAT in Leopard 10.5.8 - but I can't even find them in the Print/Fax System Preference when I start in Snow Leopard. And I don't know where to go nor what to do to find the drivers etc. etc. etc. I choose to install ALL printer drivers when I did the set-up of SL.
It was kinda automatic with 10.5 - but with 10.6 - just nothing. It finds my Canon SCANNER- but no printers...
Thanks for any comments here -- glad I've kept leopard on my internal MacBook HD!
Steve

How to set up Canon printer via Netgear print server ps121 on new macbook

I have bought a new Macbook (OS10.4.8). The Apple store gives a good deal if you buy a Canon ip4300 with it but I am having problems figuring out how to set up the printer to work thru my Netgear print server on my Netgear network. Can anybody advise:
1. I know my print server is on port 192.168.1.5, but what kind of settings do I use, IPP or LPT or something else?
2. Why can I not find the driver for the ip4300, even though I have used the CD that came with the printer and run the install program and the printer DOES work when I plug it directly into the USB port. Why does the Macbook come with drivers already installed for only a few ancient BJ Canons and why won't it show me where the driver for the ip4300 is since it is obviously already on the machine?
I know Netgear treats its customers with contempt (Linksys even worse). But I would expect a little more simplicity from Canon and Apple. I know I am an orangutan but it still seems incredibly difficult, as if they have hidden the printer driver on the computer and as if Apple does not want you to install networked printers. Please don't tell me to RTFM, I have read the Canon manual, it tells you how to network with Windows, does not even mention Mac. Any advice appreciated.
Macbook Mac OS X (10.4.8) Netgear PS121, Netgear WGT624v3 router, Canon ip4300 printer

Hi zoevancouver,
If you are not able to set up your Canon MP460 printer, take a look at the article below. There is a link to the Canon website and compatible printers. Since this particular model is not on the list, you may need to contact Canon for additional support.
OS X: Printer and scanner software available for download - Apple Support
https://support.apple.com/en-us/HT201465
Regards,
- Judy

How to set up an epson xp410 with a mac pro

How do you set up an epson xp410 printer scanner , to use wirelessly or with a usb with a macbook pro

The Espon XP410 is supposedly comaptible with Mavericks - see -> http://support.apple.com/kb/DL1398 - to download the drivers.
Also see -> http://support.apple.com/kb/PH14143 - it will tell you how to set up a printer under OS X Mavericks.
Clinton

How we set up multiple websites on OSX Server

BACKGROUND
After fiddling and futzing around for weeks (actually since last year) I've finally figured out how to set up multiple websites (virtual sites) using one port and one IP address. While there seems to be lots of discussion on this topic, it seems that the basic assumption is that one knows everything about websites, DNS and all that stuff, which I do not.
When our network was originally established the engineer set up a wiki and also configured webmail, so we had two sites, one secured for mail and the other open for Calendar and the wiki. We were not hosting any websites locally because our school website is hosted by a company in New England.
This year I wanted to set up websites for teachers and students. As great as the wiki is, there are some things it just can't do as well as a website. So I figured if I set up the sites teachers could link back and forth from one to the other. In addition kids could now start to use a real website instead of the cobbled together file mess I had when we ran a Windows network. Also iWeb is a much more accessible tool than FrontPage.
SERVER SIDE:
Snow Leopard Server - 10.6.4
There are two - actually three pieces if you want your iWeb clients to connect to the server: Server Side Web Services, DNS and, in my case, FTP.
================================================ SERVER SIDE - WEB SERVICES
If you haven't turned on Web services, you'll need to open Server Admin and do that. If you don't know how to set up web services - just reply and I'll step you through that as well.
Once web services are set up and turned on, you'll see it listed under your server’s name in the Server Admin sidebar. Click on "Web" and then click on the "Sites" tab at the top of page. This is where you list all your sites.
Click the plus button and enter the fully qualified name of your site, for example: "students.myschool.org". Don't use the defaults here (no name) - that's what got me in trouble before. BE SPECIFIC!
You'll be looking at the "General" tab (the other tabs, "Options", "Realms", etc. we'll deal with in a second).
On the "General Tab", the default IP address ("any") and port (80) is just fine. We'll run everything over port 80. (Apache figures all the virtual site stuff out - you don't need your rocket science degree for that.)
"Web Folder:" is important because this is how you'll "segment" your websites. While I would NEVER do this again, we have a solid state hard drive for the OS and a RAID array for our data files. IF you have that, make sure you do NOT use the default "Web Folder" because it will store all your files on your solid state drive. There may not be enough room, over time, on that drive. I've not experienced it yet, but it's my understanding that if the drive fills up, the server shuts down.
I store my web sites on a folder on the RAID array.
Everything else on that tab can be left as the default. (Just make sure that you have an "index.html" or "index.php" file in your web folder root, but iWeb will take care of that for you.)
I would put in your email address in the "Administrator Email:" field.
Under "Options" you really don't have to put anything. I've tested making websites with iWeb and it doesn't appear that anything needs to be checked.
Nothing needs to be entered in "Realms" as well from what I see working w/ iWeb.
The defaults in "Logging" are fine.
You can leave "Security" alone, but we do have a (self-issued) certificate listed for our webmail site.
"Aliases" is important. Under "Web Server Aliases" you enter how you want the site to respond to when users type in a URL in their web browsers.
When our web server was initially set up the engineer set up "wiki.myschool.org" on port 80 and "mail.myschool.org" on port 443. In the aliases section was nothing but a "*" (the wildcard character). That means, from what I can figure out, that the webserver will respond to these sites regardless of what is typed in the URL. (Well, something like that - point is, if you create OTHER websites, you'll NEVER get to them because the wildcard character in the "Aliases" section, in effect, grabs those web requests and redirects them to the sites that are already there.
In my case I deleted both of those wild card characters. For my "wiki.myschool.org" site, I entered "mail.myschool.org". That means if you type EITHER "wiki." or "mail.", go to the site that’s stored in the “Web Folder” we set up when those sites were created.
For "mail.myschool.org" I just DELETED the wildcard character. I wanted that site (since it was secured) only to respond to "mail." - nothing else. (You're not going to that secured site for any other reason than to get your mail.)
"Proxy" can be left blank. Have no idea what that does. As time permits I'll do some research and figure out what it's used for.
"Web Services" is if you want to provide any MORE services to this particular site. Most likely you'll want to uncheck all the boxes. For our "wiki." site, we have checked "Wikis", "Blogs", and "Calendar". For our "mail." site we have those checked PLUS "Mail".
I would create a separate "Web Folder" for each of your sites. I don't know if that's a requirement but for housekeeping purposes, I would keep the sites separated. And I SUSPECT that it's "best practice" to separate your wiki from your other websites.
SERVER SIDE - DNS
OK...now you have to make your site reachable and the only way to do that is to set up DNS so that folks don't need to type in the IP address of your web server. You need to set up DNS inside your network and, if you want folks in the outside world to reach your website, you'll need to set up an external DNS as well. I'm going to cover INTERNAL DNS - if you don't know how to set up EXTERNAL DNS - reply or email me and I'll post those instructions.
Most likely you have already created Zones for you network...all you really need to do is create "Aliases" so that when you type "students.myschool.org" your web browser will know that site resides on IP address XXX.XXX.XXX.XXX.
If you've set up Zones then you already have a "Machine" setting that translates your server’s name to an IP address and vice versa.
All you need to do is create an "Alias" (CNAME) record for, in this case, "students". You’ll see the choices for types of records when you click the "Add Record" button.
There are only two fields to configure for a record: "Alias Name" - in this case "students" and "Destination" - in this case "servername.myschool.org". (You've already entered a machine record that says "servername" = 192.168.1.x.)
That's it for Internal DNS.
SERVER SIDE - FTP
Now you have to get iWeb to communicate with the webserver.
There are only three ways iWeb will communicate with webservers: MobileMe, Local Folder and FTP Server.
Local Folder is really only practical if you want to host a website on a laptop (I was blown away initially when I found out that all Macs had a built-in web server - how neat is that?). I think there are some very cool things teachers could do with configuration, and, of course, you wouldn't need to set up any web services on the web server, but that's for another discussion. You need to set up FTP services on the web server.
Turn on and enable FTP on your webserver.
You can leave the defaults for "General", "Messages" and "Logging". "Advanced" is the only thing you want to set. I set "Authenticated Users See:" to "Home Folder Only". I set the "FTP Root" to the same root folder in which I plan to store my web sites (/VOLUMES/RAID Array/WebServer/Documents). This setting sets that folder only to be accessible via FTP.
I would suggest returning to your DNS settings and adding one more "Alias". Set "ftp." to point to your webserver. Why? So folks can edit their sites from home (see below).
CAVEAT: If you are running FTP on other servers, make sure that the settings here do not conflict with the settings on the other servers. For example, I'm running FTP on my file server so that my scanners can communicate with it. However, I configure my FTP settings by machine name and NOT "ftp.myschool.org".
================================================
CLIENT SIDE - CONFIGURING iWEB
Now you have to configure iWeb so that it will communicate with your server.
Click on the "Site" icon so that "Site Publishing Settings" appears.
Publishing:
"Publish to:" = "FTP Server"
You can set the "Site name:" and "Contact email:" to whatever you want. But see below!
FTP Server Settings:
"Server address"=ftp.myschool.org (you could also enter in servername.myschool.org or the IP address. However, if you want folks to be able to work on the site from home, you will need to configure external DNS for that. If you use the IP address, you're out of luck for remote access to the site. (You can do it but it's beyond the scope of this discussion.)
"Username" & "Password" should be your user's network login credentials.
"Directory/Path" - this is important. Remember, you set your "FTP Root" to be "/VOLUMES/RAID Array/WebServer/Documents". If you leave this field blank then the website will be dumped into this folder. If you are only setting up one site, that may be OK. However I wanted to set up a "students" site folder, a "faculty" site folder and a separate site for our literary magazine.
THEREFORE: I have, in my ..../Documents folder (on the server), a "students" folder, a "faculty" folder, and a "litmag" folder.
SO...in my "Directory/Path:" field, I have "/faculty". That means the full path to this website is "ftp root/faculty" or "/VOLUMES/RAID Array/WebServer/Documents/faculty" (You don't need a trailing "/" character. iWeb will automatically append the folder for you user depending on what you entered in "Site Name:" in the "Publishing" area.
Website URL:
This is the root website depending on whether it is "students" or "faculty". Since iWeb will append the site name to this root website, I accomplished what I hoped to accomplish in this post (http://discussions.apple.com/message.jspa?messageID=12288561#12288561).
Faculty sites will be @ http://faculty.myschool.org/username. Students @ http://students.myschool.org/username. PERFECT!
iWeb is such a GREAT tool - NOW the kids can start using it!
I want to reiterate that this works for our school but it should work for you as well. There may be better ways to do this but it works for us.
Hope this has been helpful and you won't have to spend weeks trying to figure this all out by yourself!

OK...here's how we did it.
To get access to the website you created from outside your network there are a couple of steps.
First, you have to have a STATIC IP address from your ISP. If you have a T1 circuit, no problem...you usually get a couple of static IPs you can use. However, if you have a cable modem circuit, most likely you have a dynamic IP address which changes when you connect to the internet. Usually a static IP will cost a bit more because the ISP has to go through a couple of steps to set it up for you. But once you have the address, you now have a way for folks outside your network to connect with you.
(I’m also assuming that you use a router of some sort through which traffic flows out to the internet and that you aren’t using connection sharing or something like that.)
The next thing you need to do is have your new static IP address associated with the server on which you are hosting your website. You've probably already done that if your website works inside your network. However, you've associated a private ip (192.168.x.x, etc.) to your web server. That doesn't mean anything to folks on the outside because private IP addresses are just that - private - folks can't access them. (I won't get into VPN because that's a whole other topic.)
The way you associate your new static IP address to your web server is through some sort of dns application from your ISP. For example, we use TierraNet to manage our external DNS information. They have a web interface control panel that is very similar to the DNS interface for XServer. You can create CNAME records (aliases - other ways that folks can access your servers).
Basically you create an "A" (CNAME) record with a fully qualified domain name (e.g. webserver.myschool.org) and point it to your public IP address (XXX.XXX.XXX.XXX) which you just got from your ISP. It's going to take a while (24-48 hours) for this change to take effect. BTW, you can create as many “A” records as you want. For example mail.myschool.com and wiki.myschool.com could point to the same place.
You want to make sure that the fully qualified domain name you enter in the external dns utility matches the name you used when you created your internal dns records on your XServer.
OK...so now folks can get to your domain - but, remember, you have a private network IP scheme between them and you. You now have to tell your router that when web traffic arrives, allow it inside the network and direct it to your web server.
Let's say your public IP address is 205.100.112.50 and your web server is 192.168.0.5.
You have to create, in your router’s "Security Zone" (router companies call them different things) a couple of rules. Usually the first rule is: "Let everything inside the network get out to the web." You've probably already done that if folks inside the network can reach the internet.
You then have to tell the router to allow web traffic (port 80) into your network AND redirect that traffic to 192.168.0.5.
We use AdTran routers and they have a web interface which allows you to write "rules" affecting public and private traffic. Public is folks outside the network, private is folks inside.
AdTran calls them "Security Zones" and you modify those zones with policies.
So my "Policy" would say, in the above example, redirect traffic from my public IP (205.100.112.50) -> to my web server -> (192.168.0.5).
THEN you have to modify this policy with what AdTran calls "Traffic Selectors". You've said, OK, you can get in, but WHAT can get in?
The "Traffic Selector" is written to say: "Permit" "TCP" traffic from 205.100.112.50 only through Port 80. (That's the port that web traffic goes over. If you wanted a secure website, you'd add another traffic selector that opens port 443, for example.)
I'll tell you I'm no genius when it comes to this. I called AdTran and had them configure my router for me. I told them what I wanted done, they remoted into the router and configured it. But then I could go to the web interface and see what they did and then added rules later on when I wanted, for example, to get access to the network via Apple Remote Desktop or VPN into the network on my iPad.
I'd bet that your router has a maintenance agreement that includes this service and if it doesn't it should have.
I did find that I still had issues when I tried to set this up originally and it had to do with the ORDER of the policies. I can’t remember exactly what the issue was, but, effectively one of the policies highjacked traffic before the policy that I wanted got triggered. Simply moving them around in the list fixed that issue. So if you have this set up but still can’t access the site, check the order of your rules.
I don’t know if that helps or not, but I try to think about this stuff conceptually and then get someone to help me with the details. I work with this stuff so infrequently that I forgot how I did something 6 months or a year ago. I’m in the process of creating a wiki for the school which documents all this stuff, but that’s a major undertaking.
Cheers,
John

How to set Compatibility Mode for a single site in ie10

This question was originally posted on the Answers forum -
http://answers.microsoft.com/en-us/ie/forum/ie10-windows_7/how-to-set-compatibility-mode-for-a-single-site-in/187152e3-142a-4d96-8d1b-af82ef571eec
I am having problem with getting ie10 to set ie9 compatibility for a single site (sharepoint.contoso.com).
When I add this website in Compatibility View Settings (Alt > Tools > Compatibility View Settings > 'Add this Website') it adds the domain 'contoso.com' and not the individual website (sharepoint.contoso.com).
This cause other sites (www.contoso.com) to be configured to use compatibility mode. Because this is a separate site (different web server) to the site sharepoint.contoso.com (sharepoint 2010 server) we need different compatibility settings.
Using a different example to explain the issue -
Microsoft has three websites that are different websites created by different developers written in different programming languages and they only work with certain browsers.
microsoft.com (Website1 created by Developer1) - compatible with ie8/ie9/ie10
msdn.microsoft.com (Website2 created by Developer2) - compatible with ie8/ie9
technet.microsoft.com (Website3 website created by Developer3) - compatible only with ie10
The only thing the three website share is the URL contains 'microsoft.com'.
Marking 'msdn.microsoft.com' to run in compatibility mode affects the other 2 websites - mainly technet.microsoft.com which will not work now since it only runs in pure ie10 mode.
Should you be able to add an individual site to the compatibility list instead of all sites that have .microsoft.com in the URL? Am I missing a simple setting in the ie10?
As a workaround I am using the F12 Developer Tools to set the Browser Mode which temporary sets the compatibility mode. However this is not a nice solution to the end users at our organisation.

problem is not solved for non corporate environments...
You could start your own thread. Then if you got that answer and it was marked Answered you would have the ability to unmark it. The OP of this one seems satisfied. Also note that this is TechNet. Consumers can get help on Answers
forums.
Robert Aldwinckle
Oh! I wrote it wrong: I should have said: This is not solved for NON-AD environments. No demands what so ever to use Window 7/8 professional in a small corporation or on a big corporation with Island of smaller departments for example offshore.
The problem is that the thread is not "Answered" by the OP, its is marked answered by a moderator (and same moderator that did the answer) so no way of telling if the OP is satisfied.
But you are right in the fact that I am almost kidnapping the thread. But a complete answer would benefit all in this case I would presume.
Regards
/Aldus

Once and for all: How to set up and use SSH

Yes, I know ssh has been discussed on and off, but never in its entirety; and yes, there are step by step instructions on the www, but at one point or another they skip a crucial instruction that would be necessary for unix-dummies (e.g. how to save and close the nano-editor in Terminal). So, please pardon my question:
There are several points I'd like to ask for ssh-connecting two macs on a local network:
1) In terminal-file-"connect to server" you can ask for an ssh connection to be set up. For this to work, do I need to create private and public keys first? If so, how? Please point me to a reliable and step-by-step instruction site.
There are some free ssh-utilities out there, but their documentation is just not helpful enough for a UNIX-dummy.
2) Apparently I managed to connect via ssh once (from the terminal, see point 1) to a local server (allowing remote connection set to ON at the server). But then, when I connected to that server from the client's finder and tried to get into my user account on that server it told me that no secure connection could be established. What's wrong here? Do I have to continue working from within the terminal to use this connection? That would be difficult for an average MacUser.
3) What is the security advantage of an SSH connection on a local wireless network (Airport Base Station) over WPA2, if at all?
4) And how to set up an ssh-connection over the internet cloud to safely build a remote control/desktop sharing connection, e.g., a friend's Mac when she has a problem?
Thanks for your consideration.

First I'm not sure what your goals are.
1) In terminal-file-"connect to server" you can ask for an ssh connection to be set up. For this to work, do I need to create private and public keys first?
If you have ssh keys, you can do this without passwords. If you have not exchanged keys with the remote system, you will be asked for the password of the user you are attempting to login as.
If so, how? Please point me to a reliable and step-by-step instruction site. There are some free ssh-utilities out there, but their documentation is just not helpful enough for a UNIX-dummy.
Log into the remote system. This could be via ssh.
On the remote system, run the following command to generate an ssh key for that remote system:
ssh-keygen -t rsa
Generating public/private rsa key pair.
Enter file in which to save the key (/Users/username/.ssh/id_rsa): <<take default>>
Created directory '/Users/username/.ssh'.
Enter passphrase (empty for no passphrase): <<enter nothing>>
Enter same passphrase again: <<enter nothing again>>
Your identification has been saved in /Users/username/.ssh/id_rsa.
Your public key has been saved in /Users/username/.ssh/id_rsa.pub.
The key fingerprint is:
aa:bb:cc:dd:ee:ff:gg:hh:ii:jj:kk:ll:mm:nn:oo:pp [email protected]
This will generate an ssh key for the remote system. This could be any system that support ssh, such as a Unix system, or another Mac.
Copy the id_rsa.pub file from the remote system to your Mac. When I say "your Mac" I mean the one that you want to make the ssh connection from. The id_rsa.pub is found in the remote system's ~username/.ssh/ directory.
Append the copied id_rsa.pub to your Mac's ~himbear/.ssh/authorized_keys2 file
cat id_rsa.pub >>~himbear/.ssh/authorized_keys2
Now when you ssh to that specific remote system, it will NOT ask for a password. The first time you ssh to any system, ssh will ask if the system is really the system you thing it is. But once you say "yes", it will not ask that question again.
Repeat for every remote system you wish to log into using an ssh key.
2) Apparently I managed to connect via ssh once (from the terminal, see point 1) to a local server (allowing remote connection set to ON at the server). But then, when I connected to that server from the client's finder and tried to get into my user account on that server it told me that no secure connection could be established. What's wrong here? Do I have to continue working from within the terminal to use this connection? That would be difficult for an average MacUser.
MacUser. A flash from the past, as in the MacUser magazine.
ssh is not used by default when you make connections. If you want an ssh connection, you have to establish it intentionally.
ssh can be used to pre-establish a tunnel (or tunnels) that other services can use. Once an ssh tunnel is establish, connections to local host's tunnel port will be connected to the specified remote port. For example:
ssh -L 5901:localhost:5900 [email protected]
will establish a tunnel that VNC can use. The VNC client would connect to localhost display 1 or port 5901.
ssh allows multiple -L tunnels to be specified on the ssh command line.
3) What is the security advantage of an SSH connection on a local wireless network (Airport Base Station) over WPA2, if at all?
Inside you home. Not much. Unless of course you do not trust the other members of your family. That is to say, others having your WPA2 password, and are thus on the inside, and can sniff you packets.
4) And how to set up an ssh-connection over the internet cloud to safely build a remote control/desktop sharing connection, e.g., a friend's Mac when she has a problem?
If you are using the Mac OS X Leopard built-in *Screen Sharing* and you are connecting to another Mac's built-in Leopard System Preferences -> Sharing -> Remote Management (Tiger's Apple Remote Desktop), then in the *Screen Sharing* preferences, is an "Encrypt all network data" option.
If you wish to set this option in advance, you can launch *Screen Sharing* by double clicking on System -> Library -> CoreServices -> Screen Sharing.app
You can *Screen Sharing* connections over the net using iChat. This is one of the easiest ways to take control of their system. Of course they need to cooperate. I use a Free AOL Instant Messager (AIM) account for my iChat connections. And as a side benefit you can text, audio chat and/or video chat with the person at the other end.
If you are NOT using the build-in Mac OS X *Screen Sharing* and/or you are NOT using the build-in remote Mac OS X remote management server, then this is a situation where an ssh tunnel would be a very good idea.
However, setting up an ssh tunnel between 2 systems across the internet gets complex.
In this case you might want to consider using something like LogMeIn.com which will deal with all those nasty home routers without needing to to do nasty router configurations, and it will be a secure connection. LogMeIn.com will not be as fast as a *Screen Sharing* connection or a VNC connection, but it will be secure and easy to establish. Again, this is only if you can not to Mac to Mac *Screen Sharing* using built-in Mac OS X remote desktop.
Now if you want to roll your own ssh tunnels for VNC, then I'm just going to outline the things you need to do.
If the remote system is behind a home router, you need to configure that remote home router to "Port Forward" port 22 on the Internet side to port 22 on the target Mac. Bonus points if the internet side using a high number port to discourge net bots from knocking on your door. Use the ssh -p 12345 option to connect to the high numbered port that is forwarded to port 22 of the destination Mac.
On the remote Mac you need to run a VNC server. If this is a Mac, then Leopard System Preferences -> Sharing -> Remote Management (Tiger's Apple Remote Desktop). If it is not a Mac, then for Windows, TightVNC, UltraVNC, RealVNC are possible options. Linux has a built-in vncserver, or you can install x11vnc which has the advantage of displaying the desktop screen.
Once you can access the remote system, you use an ssh command like the following:
ssh -p 12345 -L 5901:localhost:5900 remote.system.address
You can get the remote system's address by having the remote system surf over to http://whatismyip.com. Then they can tell you the IP address.
If you are going to be doing this a lot, you can get a free no-ip.com or dyndns.org dynamic DNS name for the remote system, and the remote system can run a dynamic DNS client (available from no-ip.com or dyndns.org) which will keep the dynamic DNS name updated as the remote person's ISP change's their IP address.
Finally, now that you have an ssh tunnel for VNC traffic, you have your VNC client connect to
Address: localhost
Port: 5901
Depending on your VNC client you may need to specify Display 1 instead of Port 5901. Or if you do not get a Display or Port option you specify localhost:5901

TS3899 I can't SEND email from Telus account in Alberta, Canada? Does anyone know how to set up the Outgoing server? Help! And thanks!

Can't SEND email from Telus account in Alberta, Canada, unless I go to web mail. Does anyone know how to set up the Outgoing server? Incoming is fine. Outgoing used to work. We changed it when we went to another location, and can't get it back. Telus support can't fix it. Neither smtp.telus.net NOR mail.telus.net works for Outgoing server to send mail. Please help! Thanks.

iOS: Unable to send or receive email
http://support.apple.com/kb/TS3899
Can’t Send Emails on iPad – Troubleshooting Steps
http://ipadhelp.com/ipad-help/ipad-cant-send-emails-troubleshooting-steps/
Setting up and troubleshooting Mail
http://www.apple.com/support/ipad/assistant/mail/
Server does not allow relaying email error, fix
http://appletoolbox.com/2012/01/server-does-not-allow-relaying-email-error-fix/
Why Does My iPad Say "Cannot Connect to Server"?
http://www.ehow.co.uk/info_8693415_ipad-say-cannot-connect-server.html
iOS: 'Mailbox Locked', account is in use on another device, or prompt to re-enter POP3 password
http://support.apple.com/kb/ts2621
iPad Mail
http://www.apple.com/support/ipad/mail/
Try this first - Reset the iPad by holding down on the Sleep and Home buttons at the same time for about 10-15 seconds until the Apple Logo appears - ignore the red slider - let go of the buttons. (This is equivalent to rebooting your computer.)
Or this - Delete the account in Mail and then set it up again. Settings->Mail, Contacts, Calendars -> Accounts Tap on the Account, then on the red button that says Remove Account.
 Cheers, Tom

How to set up roaming profile on Macs using AD like in windows

I can bind the workstations to the domain fine.. But can someone direct me to instructions of how to set up the roaming profiles ?
What steps do I need on the server ? This is what I've done so far.
I already have OU's for the departments and the users have a shared folder inside their department folder.... \\server\shared_folder\user
I have done the usual things with AD as far as the profile settings on the windows server.
Am currently running Mac OS 10.5 and above
My windows AD runs on windows server 2008
All my windows workstation are able to use roaming profile without a problem.
So far i have tried the so many avenues including..
Make sure the Mac systems are joined to the domain controller and an ADS user can log on successfully. Use "Directory Utility" under "Utilities" menu to join the system to the domain.
Backup all the contents from /Users to the storage or somewhere locally.
Configure automount - Go to "Utilities" -> "Directory Utility" - Select the domain and click "Show advanced options" - Click "Mounts" tab and add automount as mentioned below. Remote NFS URL: nfs://server_name/share_name/path/to/profile/directory Mount location: /Users Additional mount parameters: -P,-T Apply the settings and this will mount the remote shared folder or we can name it as Roaming Profile Space - under /Users directory
Enable roaming profile - Go to "Utilities" -> "Directory Utility" - Select the domain and click "Show advanced options" - Click "Services" -> Select "Active Directory" and click "Show advanced option" - Click "User experience" tab and select the option "Create mobile account at login".
Reboot the system and log in as any ADS user. The Roaming shared folder will be mounted and the user profile will be created on the shared folder
Can anyone kindly assist me

Hi Guys, anyone with the Soln...or Tips..Am waiting

How to set up user account and share folders

We are a family of four sharing our first iMac. I would like to set up one account for my wife and I and one account for my kids on which I plan to enable Parental Controls.
I have struggled with setting up my kids user account. After setting up a Standard account for the kids - I noticed none of our music or files were visible in the kids accounts. I spent 20 min on the phone with Apple and the tech was clueless. He had me copying my music folder all over the computer until I had about 6 copies of the same folder. I did figure out how to move the music library to SHARED folder and redirect iTunes source folder to the same shared folder.
My problem now - when I copy my documents to the SHARED folder my kids can see the files and open them, but they can not save them. How do I give the kids account read write privileges?
Should I set up a GROUP account instead?
I need the best way to have two or three users who can access all data on the same iMac, while giving me the ability to enable Parental Controls on the accounts.

Do this:
Here's how to set it up by using ACLs:
1. Create a new folder in /Users/Shared. Call it "Sharefolder".
2. Log in to an Admin account, open Terminal and paste in all of this at the same time:
chmod -R +a "everyone allow delete,chown,list,search,add_file,\
addsubdirectory,delete_child,file_inherit,directoryinherit" \
/Users/Shared/Sharefolder
That will automatically make everything copied or created to the sharefolder writable by all users. Note: After setting this up, if you have existing files that you want to move to the sharefolder, hold down the option key when dragging them in. That will make new copies of them in the sharefolder. Dragging existing files in (i.e. simply moving them there) won't cause the ACL to inherit properly and they won't be writable by all users. Files that are copied or +newly created+ in the sharefolder shouldn't have this problem.
Make sure you keep good backups. One user accidentally deleting a shared file will affect everybody else who uses it.

How to set up for user's request to go through a specific module that i selected

I am testing if it is possible all requests from users should go through a module
that i made or not.
For example, all most web server is setted all requests should go through the
log module for writing log when users request a certain page.
Like this, how to set up the configuration all request should go through a certain
module.
Would you tell me the answer please.

Power on the Time Capsule for a few minutes, then hold in the reset button firmly with a ball point pen or something similar for 10 seconds and release. Allow a full minute for the Time Capsule to restart to a slow, blinking amber light.
Connect an Ethernet cable from one of the LAN <--> Ethernet ports on the back of the Uverse router to the WAN "O" port on the Time Capsule
On your Mac, open up Macintosh HD > Applications > Utilities > AirPort Utility
Click on the Other WiFi Devices tab
Click on the Time Capsule
The setup utility will open up automatically and take a minute to analyze the connections then suggest a setup on a screen that looks like this:
Type in a simple name that you want to use for the Wireless Network Name
Type in a name that you want to use for the Time Capsule device
Type in a password
Verify the password
Click Next
The utility will set everything up for you in a minute or two. When you see the message of Setup Complete on the screen, click Done
You can now log onto the wireless network that you created by selecting the name and entering the password
Post back on your progress and we will next get backups going again

How to set the table input in Query template?

Hi all.
I need to call a Bapi_objcl_change, with import parameter and a table as an input. I have done this, in BLS. I have set the table input in the
form of xml. In BLS, I get the output(the value gets change in SAP R3, what i have given in BLS). But if i set the same xml structure in
query template, I didn't get the output. Table input parameter does not take that xml source. How to set the table input in Query template?
can anyone help me?
Regards,
Hemalatha

Hema,
You probably need to XML encode the data so that it will pass properly and then xmldecode() it to set the BAPI input value.
Sam

How to set up my scanner?

Similar Messages

Maybe you are looking for