How to set up postscript Printer for printing graphics

We have a requirement to print Structured graphics. I found out that we need to set up a postscript printer for it. After debugging I found out that the Device Type name should be either GRAPHICS or POSTGR or ZGRAP.
How can we set up such a printer?
Thanks in adv.

Hi,
The Device Type names that you have provided are not listed in the SAP Central Note for Printers/device Types
https://service.sap.com/sap/support/notes/8928
However, you can again re-check this note with your printer model and check what suitable device types should be used. As you will find inthis note:
"Device type definitions are stored completely in tables and can be individually adapted, modified or enhanced. If SAP performs such an adjustment for a customer, it constitutes a consulting service, and is generally charged seperately"
SAP has now released the SAP Printer Vendor Program - https://service.sap.com/sap/support/notes/1130927, printer manufacturers can develop and release device types for their printers.
https://service.sap.com/sap/support/notes/1100779 contains a list of all participants
Information about the support for new printer models is contained in the "Printer Vendor Wizard Note" of the relevant manufacturer. A complete list of all "Printer Vendor Wizard Notes" is available in Note 1097990. If your printer model is not listed in one of these "Printer Vendor Wizard Notes", proceed as described in Note 1103826.
- Regards, Dibya

Similar Messages

How to set up Canon printer via Netgear print server ps121 on new macbook

I have bought a new Macbook (OS10.4.8). The Apple store gives a good deal if you buy a Canon ip4300 with it but I am having problems figuring out how to set up the printer to work thru my Netgear print server on my Netgear network. Can anybody advise:
1. I know my print server is on port 192.168.1.5, but what kind of settings do I use, IPP or LPT or something else?
2. Why can I not find the driver for the ip4300, even though I have used the CD that came with the printer and run the install program and the printer DOES work when I plug it directly into the USB port. Why does the Macbook come with drivers already installed for only a few ancient BJ Canons and why won't it show me where the driver for the ip4300 is since it is obviously already on the machine?
I know Netgear treats its customers with contempt (Linksys even worse). But I would expect a little more simplicity from Canon and Apple. I know I am an orangutan but it still seems incredibly difficult, as if they have hidden the printer driver on the computer and as if Apple does not want you to install networked printers. Please don't tell me to RTFM, I have read the Canon manual, it tells you how to network with Windows, does not even mention Mac. Any advice appreciated.
Macbook Mac OS X (10.4.8) Netgear PS121, Netgear WGT624v3 router, Canon ip4300 printer

Hi zoevancouver,
If you are not able to set up your Canon MP460 printer, take a look at the article below. There is a link to the Canon website and compatible printers. Since this particular model is not on the list, you may need to contact Canon for additional support.
OS X: Printer and scanner software available for download - Apple Support
https://support.apple.com/en-us/HT201465
Regards,
- Judy

Adobe Reader XI...How to set it to Print as Image as default

Hello I using Windows 7 64 bits version and using Adobe Reader XI. I need to know how to set reader to Print As Image to default. Is there registry setting in windows or VB script that can do it? I alread found it in version. I need to find it this in Version XI. Any usefull solution or suggestions would be helpful.
Thanks

Are you using the Organizer? If you have imported your photos into the organizer it’s possible to select thumbnails and then on the top menu click Edit à Edit With Photoshop Elements
Click to view

HOW TO SET A DEAFULT VALUE FOR A FIELD?

hi friends
i have doubt..how to set a default value for a field..say like in local printer field i always want lp01 to be displayed defaultly..when i click F1 in that field i get the parameter id ..i know there is something dealt with that parameter id..how can i set that default value ..in the case of the default printer value i made in own data settings as lp01 but how to do it normally for other field which has parameter id ??????
thanks and regards
prince

Hi Prince,
u can set the default value in abap as given below
SELECTION-SCREEN: BEGIN OF BLOCK B1 WITH FRAME TITLE TEXT-001.
SELECTION-SCREEN SKIP 1.
PARAMETERS : S_BUKRS TYPE BSID-BUKRS OBLIGATORY DEFAULT '1000'.
PARAMETERS : S_BELNR TYPE BELNR_D OBLIGATORY DEFAULT '1600000070'.
PARAMETERS : S_GJAHR TYPE GJAHR OBLIGATORY DEFAULT '2008'.
PARAMETERS : ASON TYPE BUDAT OBLIGATORY DEFAULT SY-DATUM.
PARAMETERS : S_KUNNR TYPE KUNNR MODIF ID GP1.
PARAMETERS : S_LIFNR TYPE LIFNR MODIF ID GP2.
SELECTION-SCREEN SKIP 1.
SELECTION-SCREEN : END OF BLOCK B1.
or
u can give the default value in INITIALIZATION also.
vlue = '1000'.

SRM 4.0- How to set the default values for product type (01) only for SC

The radio button Service should not be visible.
Also for search help (e.g. search for internal products) where a search should only be possible for product type 01 (goods). The system should not display the product type and internally always search for goods only.
How to set the default values for product type (01) only for SC
We needs to use Search help BBPH_PRODUCT which having parameter PRODUCT_TYPE
Here we can set defalut value 01 but it is not correct one since same search help is using several places.
We need to limit the search help results only for SC.
Kindly help out me ASAP.

The easiest way to set defautl values is to edit the batch class.
Goto the characteiristic and go to update values.
In here you probably have something like 0 - 100 as a spec range.
On the next line enter the default value within this range. At the end of the line, click in the box in the column labelled "D". This indicates the defautl value for the characteristic.
If you need to you can do this in the material classification view as well.
Just to be clear, these values will only show up in the batch record. You can not have defautl values in resutls recording screens.
FF

How to set up automatic payment for the purchase order

Hi, All,
I have one question how to set up automatically payment for the Rent Office purchase Order?
There is the requirement from the client. They want to create one kind of purchase order for the Office Rent, then pay the fees in the certain time of every month to the vendor for the rent fees without any invoice. Whatu2019s the normal solution for this kind of purchase order? Is it ERS? Or something else?
Please give me the details and business flow. Also please tell me how to setup in the SAP and T-code.
Thanks in advance

Either you can set up ERS or you can pay directly from the FI side.
Prerequisites
Evaluated receipt settlement must be flagged in the purchase order item.
The vendor must be flagged as being subject to ERS in the vendor master record.
The goods receipt must refer to a purchase order.
Goods-receipt-based Invoice Verification must be defined for the purchase order item.
A tax code must have been maintained in the purchase order item.
The order price of the materials may not be an estimated price.
If you flag a vendor as being subject to ERS, the system sets the ERS indicator as a default in each item when you create a purchase order for the vendor. You can prevent this happening for certain vendors by flagging the info record for the material and the vendor as not being subject to ERS.
In Purchasing, you can delete the default ERS indicator in a purchase order item.
Choose Logistics Invoice Verification ® Automatic Settlement ® Evaluated Receipt Settlement (ERS).
The selection screen appears.
You can use the following criteria to narrow down selection of the transactions to be settled:
Company code
Plant
Goods receipt posting date
Goods receipt document
Fiscal year of the goods receipt
Vendor
Purchase order and order item
You can define the selection criteria for the invoice documents by:
Delivery
Purchase order
Purchase order item
Goods receipt document
Credit memo
Invoice
Currency
Choose Execute.
The system issues a log for Evaluated Receipt Settlement, which displays the following:
Settled
In line with your selection criteria, the system displays all the order items that were settled (or if you are working in test mode, which would have been settled).
Could not be settled
In line with your selection criteria, the system displays all order items for which ERS is defined but could not be settled. It also lists the reasons.
If the system reports being unable to invoice a transaction, you should exclude the transaction from ERS to avoid it being included in the log the next time ERS is run.
Select the item and choose Exclude from ERS.
The system also generates and possibly sends a message to inform the vendor(s) about the transaction settled, depending on the settings in Customizing.
You can display the following environment information for the order items selected. To do this, choose Goto ®:
Display purchase order
Display invoice
Display material document
Display long text

How to set up Airport Extreme for 11ac and 11n?

I have just purchased the new Airport Extreme (August 2014) because Apple's website states
Simultaneous dual-band support.
AirPort Extreme features simultaneous dual-band 802.11ac Wi‑Fi. That means it transmits at both the 2.4GHz and 5GHz frequencies at the same time. So no matter which band your wireless devices use, they’ll automatically connect to the best available band for the fastest possible performance.
I have number of Macs in my home from a new MacBook Pro with Mavericks to a Macbook Air with Snow Leopard (due to required software) and iPads.
So after setting up the new Extreme my new MacBook only accesses 11n as does my older Macs. I checked by holding down the option key while clicking the WiFi icon at the top of my Mac. Well, not so automatic then as I was expecting 11ac and 3 times faster access (as stated by Apple).
I then looked for some documentation for setting up but cannot find anything.
Hence my question here.
How to set up Airport Extreme for 11ac and 11n simultaneously?
At present the new Extreme is no better than my previous 2 year old one.
Thank you.
Michael

How to set up Airport Extreme for 11ac and 11n simultaneously?
Assuming that it is operating correctly, 802.11ac and 802.11b/g/n are broadcast simultaneously by default.
Simultaneous dual-band support.
AirPort Extreme features simultaneous dual-band 802.11ac Wi‑Fi. That means it transmits at both the 2.4GHz and 5GHz frequencies at the same time. So no matter which band your wireless devices use, they’ll automatically connect to the best available band for the fastest possible performance.
That is advertising. The real information is usually found in the small and hard to read footnotes:
Based on theoretical peak speeds. Actual speeds will be lower.
AirPort Extreme is based on an IEEE 802.11ac draft specification. Performance based on comparison with Apple’s 802.11n products. Comparison assumes AirPort Extreme network with 802.11ac-enabled computer. Speed and range will be less if an 802.11a/b/g product joins the network. Accessing the wireless network requires a Wi‑Fi-enabled device. Actual speed will vary based on range, connection rate, site conditions, size of network, and other factors. Range will vary with site conditions.
Since the 802.11ac signal is being broadcast only using the 5 GHz band, some users report that they have had better results by using the option to assign a different name to the 5 GHz band, and then pointing their Mac to that specific signal or network. You may want to try that option.
But first as a test, please locate the MacBook Pro about 10-15 feet or 3-4 meters from the AirPort Extreme with clear line-of-sight between the two devices. Restart both the AirPort Extreme and the Macbook Pro and then check to see if the Mac is connected to an 802.11ac signal.
If not, please power off your other wireless devices...computers, mobile devices, etc. temporarily, and try the same test again.
Please report on your results.

How to set-up a Timestamp for BI Delta Load in 0CLM_INVOICE datasrc at R/3?

Hi Experts,
Kindly let me know How to set-up a Timestamp for BI delta load at R/3 for the Data source 0CLM_INVOICE ?
Since the Timestamp for Upload of BI Delta is " . . : : ", we are not getting any delta value to BW.
I would like to know in where we need to maintain the DATE & TIME to fix the above problem.
Thanks.
Regards,
Jayaprakash J

Dear Jayprakash,
Chech the below links, it may help you in your case :
Re: 0FI_AA_11 Delta load failure
http://wiki.sdn.sap.com/wiki/display/BI/GeneralErrorIn+BI
Actaully you need not have to maintain the timestamp. Just try to replicate your datasource and the try to load the delta again.
Hopefully it will work.
Regards,
Rahul
Edited by: Rahul on Dec 10, 2010 10:23 AM

How to set a default value for particular field in SRM PO Portal

Dear Gurus,
Im desparetly need a help in web dynpro on how to set a default value for a field(flag) in PO header tab in portal.
My requirement is whenever the user press the edit button in PO screen,automatically a flag field should be set as abap_false.
I dont think this will handle in check badi or change badi. i tried this part in onbuttonpressed overwriteexit in CNR_VIEW views,i can get the function EDIT in debugging mode,but dont know how to proceed further.....
Many of them suggested to go with get attribute and set attribute for changing any particular field in web dynpro,but im not very familiar in using those get and set attributes.I request you people can give me sample code on how to identify my target field in the node and set the values while pressing EDIT Button.
Thanks in advance...
Regards,
Sathish

Dear Laurent,
Thanks for your response,
But i searched in enhancement spot of WD_BADI, but couldnt get the exact way to change the coding,
My real requirement is, that particular flag should be enable and disable dynamically by checking a condition in my header values.So in that case i dont know how to proceed further to handle in the PO screen.
Kinly guide me how to get the particular node of field in the Purchase order screen.
Thanks you in advance,
Sorry for the inconvenience if any
Regards,
sathish

How to set a new value for formula field in crystal reports xi?

How to set a new value for formula field in crystal reports xi?//formula{@description} exemplo in VB6crxSubreport.FormulaFields.Item(1).Text = "'Subreport Formula'" orcrxSubreport.FormulaFields.Item("description").Text = "'Subreport Formula'"How to in JRC? 

Hi,
This functionality is known to be very important and is a key part of the next major release of the JRC planned for the first half of 2008.
Regards,
Blair Wheadon
Product Manager, Crystal Reports

"I would like to know how to set the default view for the columns. Somewhere I read it could be done in by music icon under Library. Can't find it. Thanks

"I would like to know how to set the default view for the columns that are shown in iTunes. Every time I open it, I have to either go to the options, or right-click to get the pop-up options, and delete "rating" and add "composer." I'd really like to just do it once and be done with it." Somewhere I read you could do this by clicking on the Music icon under LIBRARY then arramge the columns. Trouble is, I can't find a Musi Folder or icon in my user library.
Any help would be appreiated. OSX 10.9.2 iTunes version 11.1.5 Thanks!!! CW!

From the iTunes menu bar try View>Show View Options. Make sure what you want to see is checked and what you don't is unchecked. You can do this (may need to do this) for any playlists, your main Library, etc.
Good luck
srb

How to set the AS2 fileName for outbound Functional Ack 997 auto generated by Oracle B2B

Hi Friends,
How to set the AS2 fileName for outbound Functional Ack 997 auto generated by Oracle B2B.
External Trading Partner is sending the EDI 856 via AS2 URL to our Oracle B2B Server.
In the inbound 856 agreement, we have checked the option of Funtional Ack and also Functiona Ack handled by B2B is yes.
We have the outbound agreement which is sending that Functional ack 997 (auto generated by oracle b2b) and we have specified the Outbound AS2 channel of the Partner.
997 doc is being sent to external partner using AS2 channel, but the filename is generating as '40101'.
Please can you let me know how to set the AS2 fileName for outbound Functional Ack 997 auto generated by Oracle B2B.
Appreciate your valuable answers!!
Thanks,
Amirineni

Amirineni,
AFAIK, there is no option to set the file name when the 997 is generated automatically by B2B.
Alternatively, if this is a must requirement, you can generate the FA from backend and send to B2B with MSG_TYPE =9. In this case, you can set the header with filename (How to set the actionname property in B2B 11g)

How to set a date range for date field ?

Dear Experts,
Scenario:
I have a query in validating the date field in my BSP application. My application is for maintain infotype 0023 Other/Previous Employers online by employees in the company.
As per our design we are maintaining the all employment details of the employee both ( with in the current company / previous employment outside the company) in the same infotype.
Every employee will have a hiring date within the SAP HR system. We consider this date as the cutoff date between current and previous employment in our application. When the employee updating the details wia BSP page I need to check the following.
Record inside current company: Validation that, the user should only able to enter BEGIN DATE (BEGDA) greater than or equal HIRING DATE and END DATE(ENDDA) should be greater than FROM DATE (BEGDA).
Record outside current Company: Validation that, the user should only able to enter BEGIN DATE (BEGDA) less than or equal HIRING DATE and END DATE (ENDDA) should be greater than FROM DATE (BEGDA) and less than HIRING DATE.
Technical Requirement:
How to set a date range for date field, i.e. how we can limit the date range in a HTMLB date field? Can this it be achieved via standard functionality of HTMLB?
Following is the code to describe date field in my application.
 <htmlb:inputField id= "ENDDA_NEW_IN"
 type= "date"
 doValidate= "TRUE"
 showHelp= "TRUE"
 disabled= "FALSE"
 width= "183"
 style= "cssTextAreadate"
 value= "<%='99991231'%>"/>
Thanks a lot in advance for your assistance and help.
Cibinu2026
Edited by: cibin kuruvilla on Nov 12, 2008 11:13 AM

Hi,
This functionality is known to be very important and is a key part of the next major release of the JRC planned for the first half of 2008.
Regards,
Blair Wheadon
Product Manager, Crystal Reports

How to set the Default values for Info Objects in Data Selection of InfoPac

Hi All,
Flat file Extracion:
How to set the Default values for Info Objects in Data Selection Tab for Info Package
ex: Fiscal Year Variant Info Object having values 'K4' 'Y2' etc in Flat file
Initially default value(not constant) for this info Object value should be 'K4' in Info Package
If I set data selection value for this info object K4 it will retreive records with this selection only? how to handle
Rgds,
CV

Hi,
suppose as your ex. if you are having fiscalyear variant in the dataselection tab then specify K4 in the from column, again the ficalyearvariant row and click on insert duplicate row at the bottom . you will get another row . In that enter Y2 in the from column. now you can extract K4, y2 values .
haritha

How to set custom master page for social/sites.aspx in sharepoint 2013

How to set custom master page for social/sites.aspx in sharepoint 2013.?
File path is
C:\Program Files\Common Files\microsoft shared\Web Server Extensions\15\TEMPLATE\FEATURES\SocialDataStore\SocialDataStoreList\sites.aspx
Thanks in advance

Hi,
You could open the sites.aspx in Notepad or SharePoint designer, and set the master page to your own master page directly via editing:
<%@ Page language="C#" MasterPageFile="~masterurl/custom.master" Inherits="Microsoft.SharePoint.Portal.WebControls.FollowedContentWebPartPage,Microsoft.SharePoint.Portal,Version=15.0.0.0,Culture=neutral,PublicKeyToken=71e9bce111e9429c"
%>
Regards,
Rebecca Tu
TechNet Community Support

How to set up postscript Printer for printing graphics

Similar Messages

Maybe you are looking for