How to set & use digital trigger for AIN on a DAQmx?

1) How I configure a task to allow a digital input line to trigger a AIN reading in VB6.0 with a USB-6210?
2) To help me answer the above I created a task in Measurement & Automation Explorer that used a digital trigger (TRIGGER TYPE= DIGITAL EDGE, TRIGGER SOURCE = PFI0, EDGE=RISING). Then from VB I tried to figure out the parameters that were set. I had no luck. So, once I understand to achieve (1) above I want to be able to verify the resulting settings. What command(s) would I use?

Hi Hjehan,
I recommend checking the following knowledge Base that can point you to the different DAQmx examples.
Regards,
Faris A
Bueller

Similar Messages

Does the SCC-DI01 can be set as a trigger for strain gage measurement?

I used the SCC-SG01 to measure the strain. I need a trigger to activate the gages to get the data when the test happen. Can I use the SCC-DI01 as a trigger for gages for my test? If I can, how I can do it?

Hello hopezx,
The 2345 is a fairly passive device that does not actually have a lot built into it other than the signal conditioning. So the actual thing that we need to look at is the DAQ card that you have attached to the 2345. What you need to check on is the product page on ni.com to see if your device support digital triggering. If it does, then you can use a digital trigger for your task just like any other.
Please post back if you have any other questions or would like some more details. If you do post back, please make sure to let us know what other hardware you are using.
ColeR
Field Engineer

How do I use the VIs for the Fluke Hydra Series 2620a multimeter?

This message refers to the VIs found at this link:
http://sine.ni.com/apps/we/niid_web_display.download_page?p_id_guid=E3B19B3E9468659CE034080020E74861
How do I use the VIs for the Fluke Hydra Series 2620a multimeter? I am conducting a Senior Design Project at Temple University. It is a Control System where I need to read voltages from sensors and output voltages to different system components. I am trying to set up a VI using the VIs found above to make sure that I can successfully read and send voltages. There was no documentation given with the 2620a VIs.

Unfortunately, you've got a very old driver for an old instrument. The only available help is to turn on Context Help and move your mouse over the VI icon. It doesn't appear to have any help for individual controls and indicators. The only good news is that it appears to be a simple instrument with only a few functions. There's some main ones line initialize (to set serial port), configure channel, configure instr, and read values. One main thing is whether you're using gpib or serial, Each front panel has a setting. If it's gpib, set the port to the gpib address. If it's serial, set the port to one number less than the com port you're connected to. For example, if you're using Com1, set the port to 0. For the other controls, I'm afraid that you're going to have to try and compare what's there with the controls and settings of the actual instrument. Having access to the instrument manual will be essential. I would engourage you to experiment a little. There's probably very little chance of damaging the instrument especially if nothing is hooked up to it. Send a command and see what happens or set the instrument up manually and see if you can reproduce that via remote control.

SRM 4.0- How to set the default values for product type (01) only for SC

The radio button Service should not be visible.
Also for search help (e.g. search for internal products) where a search should only be possible for product type 01 (goods). The system should not display the product type and internally always search for goods only.
How to set the default values for product type (01) only for SC
We needs to use Search help BBPH_PRODUCT which having parameter PRODUCT_TYPE
Here we can set defalut value 01 but it is not correct one since same search help is using several places.
We need to limit the search help results only for SC.
Kindly help out me ASAP.

The easiest way to set defautl values is to edit the batch class.
Goto the characteiristic and go to update values.
In here you probably have something like 0 - 100 as a spec range.
On the next line enter the default value within this range. At the end of the line, click in the box in the column labelled "D". This indicates the defautl value for the characteristic.
If you need to you can do this in the material classification view as well.
Just to be clear, these values will only show up in the batch record. You can not have defautl values in resutls recording screens.
FF

How to set up automatic payment for the purchase order

Hi, All,
I have one question how to set up automatically payment for the Rent Office purchase Order?
There is the requirement from the client. They want to create one kind of purchase order for the Office Rent, then pay the fees in the certain time of every month to the vendor for the rent fees without any invoice. Whatu2019s the normal solution for this kind of purchase order? Is it ERS? Or something else?
Please give me the details and business flow. Also please tell me how to setup in the SAP and T-code.
Thanks in advance

Either you can set up ERS or you can pay directly from the FI side.
Prerequisites
Evaluated receipt settlement must be flagged in the purchase order item.
The vendor must be flagged as being subject to ERS in the vendor master record.
The goods receipt must refer to a purchase order.
Goods-receipt-based Invoice Verification must be defined for the purchase order item.
A tax code must have been maintained in the purchase order item.
The order price of the materials may not be an estimated price.
If you flag a vendor as being subject to ERS, the system sets the ERS indicator as a default in each item when you create a purchase order for the vendor. You can prevent this happening for certain vendors by flagging the info record for the material and the vendor as not being subject to ERS.
In Purchasing, you can delete the default ERS indicator in a purchase order item.
Choose Logistics Invoice Verification ® Automatic Settlement ® Evaluated Receipt Settlement (ERS).
The selection screen appears.
You can use the following criteria to narrow down selection of the transactions to be settled:
Company code
Plant
Goods receipt posting date
Goods receipt document
Fiscal year of the goods receipt
Vendor
Purchase order and order item
You can define the selection criteria for the invoice documents by:
Delivery
Purchase order
Purchase order item
Goods receipt document
Credit memo
Invoice
Currency
Choose Execute.
The system issues a log for Evaluated Receipt Settlement, which displays the following:
Settled
In line with your selection criteria, the system displays all the order items that were settled (or if you are working in test mode, which would have been settled).
Could not be settled
In line with your selection criteria, the system displays all order items for which ERS is defined but could not be settled. It also lists the reasons.
If the system reports being unable to invoice a transaction, you should exclude the transaction from ERS to avoid it being included in the log the next time ERS is run.
Select the item and choose Exclude from ERS.
The system also generates and possibly sends a message to inform the vendor(s) about the transaction settled, depending on the settings in Customizing.
You can display the following environment information for the order items selected. To do this, choose Goto ®:
Display purchase order
Display invoice
Display material document
Display long text

How do i use parallel compression for 4 drum tracks in Logic pro 7.2.3 Please

how do i use parallel compression for 4 drum tracks in Logic pro 7.2.3 Please. my version is 7.2.3 and my son did his drums on 4 tracks. 2 OH's 1 Kick and 1 Snare. Were confused because we cant figure out how to do parallel compression on the older logic version 7.2.3?

I can't remember when the Aux tracks became the new buss tracks, so I'll spell this out using busses.
The way I do it, is I assign all my drum tracks to a buss, say buss 1.
Then, on buss 2, I assign it's INPUT to buss 1.
So buss 1 (all the drums) are feeding into buss 2 simultaneously.
Put a compressor on buss 2, turn the fader down all the way, then as the track is playing, bring buss 2's fader up slowly, until you hear the effect you're after.
You could also do this using sends on the 4 drum tracks, set to feed the buss with the compressor on it.
I hope I haven't forgotten anything particular to that version of Logic. See if this helps...

HT3354 how can i use one table for reference to another

how can i use a table for a referance to another eg when i type a word in a cell, i will like it to match the word with another table then return the information in the cell i am using

you can use vlookup() (or any of the lookup family of functions) to locate an item based on a key value:
Here is an example of something you can do with two tables:
The table on the right is title "Data" and stores a list of names with age and favorite color.
The table on the left uses the value in the first column to lookup up information in the table Data
in the table on the left:
B2=IFERROR(A2&" is " & VLOOKUP(A2, Data :: A:D, 2, 0)&" years old and likes the color "& VLOOKUP(A2, Data :: A:D, 3, 0), "NOT FOUND")
I know this look complicated. so I'll break it up into smalled pieces:
first the "&" is called the concatenate operator and joins two strings. like this:
a string is a set of characters between double quotes.
so "string 1" & "string 2" becomes "string 1string2" or "Sam " & "Jones" becomes "Sam Jones"
you can use cell references instead of strings directly in which case the concatenation is performed on the contents of the cells.
so if cell A1 contains "Hi " and the cell A2 contains "There" then A1 & A2 will result in "Hi There"
so you could add the formula
A3=A1 & A2
this is short hand for select cell A3 then type everything including the A3 so that A3 contains "=A1 & A2" (omit the double quote)
OK. So the formula I provided concatenates several items together:
it concatenates A2, then the string " is " then a formula, then the string " years old and likes the color " then a formula
the two formulas (highlighted in blue) perform a lookup of the value in cell A2 in columns A thru D of the table named "Data". If if finds the value in cell A2 in the first column of the lookup range in the table Data (column A) then it returns the value from the same row but in the second or third column.
all that is in a function calld iserror() to trap the condition where the calue you enter in A2 does not exist in the table Data:
You will find the Numbers users guide and function reference helpful. You can download then from Apple here:
http://support.apple.com/manuals/#productivitysoftware

How can I use jbo:InputSelect for a char type filed?

How can I use <jbo:InputSelect for a char type filed?
I have two tables. One is room (primary key is room(type is char)), another table is responsibility (foreign ker is room(type is char)). Both tables have same length for room column.
There is a problem:
If I use (in the "DataEditComponent.jsp" file)
<jbo:InputSelect multiple="false" datasource="dsEdit" displaydatasource="roomData" displaydataitem="ROOM" displayvaluedataitem="ROOM" ></jbo:InputSelect>
to get the room input for responsibility from combobox(Datasource roomData is from room table). In the form the room field cannot bind the data in combobox, alway select the first item. And if I select one item and click the update button.There is an error message:
Error Message: JBO-27010: Attribute set with value H409 for Room in Responsibility has invalid precision/scale
I found If I changed the field type from char to varchar2 in database also change the entity objects, it works well. I wonder if there are any diffrence using <jbo:InputSelect tag in char and varchar2 type. How can I use <jbo:InputSelect for a char type filed as i don't want to change my datatype in database at this stage.
I try this in JDeveloper 9.03, 9.034, 9.04. The result is the same.

If I were in your shoes, here's how I would do it:
<%-- Assuming you have dsRoom and dsResponsibility --%>
<%-- Select is an HTML tag --%>
<select name="ROOM" size="1">
<% char roomID =""; // Init your character var
// Open a rowsetIterator to get the records and add them to the LOV
<jbo:RowsetIterate datasource="dsResponsibility" changecurrentrow="true" >
<% roomID = (char)dsResponsibility.getRowSet().getCurrentRow().getAttribute("ROOM"); // Grab the char value
// add the value to the LOV
%>
<option value="<%=roomID%>"><%=roomID%></option>
</jbo:RowsetIterate>
</select>
If you are using this as part of an edit page you may want to utilize the "selected" option of the <option> tag. In one instance I am doing this on an edit page because the use may open an existing record. If I don't account for it, then it will change the DB to contain the first value from the list! You can do a simple check like:
//Set the current record's char
char curRecord = (char)rowEdit.getAttribute("ROOM");
// inside the iterate:
if (curRecord == roomID) {
<option value="<%=roomID%>" selected><%=roomID%></option>
} else {
<option value="<%=roomID%>" ><%=roomID%></option>
Hope that helps!

How to set up Airport Extreme for 11ac and 11n?

I have just purchased the new Airport Extreme (August 2014) because Apple's website states
Simultaneous dual-band support.
AirPort Extreme features simultaneous dual-band 802.11ac Wi‑Fi. That means it transmits at both the 2.4GHz and 5GHz frequencies at the same time. So no matter which band your wireless devices use, they’ll automatically connect to the best available band for the fastest possible performance.
I have number of Macs in my home from a new MacBook Pro with Mavericks to a Macbook Air with Snow Leopard (due to required software) and iPads.
So after setting up the new Extreme my new MacBook only accesses 11n as does my older Macs. I checked by holding down the option key while clicking the WiFi icon at the top of my Mac. Well, not so automatic then as I was expecting 11ac and 3 times faster access (as stated by Apple).
I then looked for some documentation for setting up but cannot find anything.
Hence my question here.
How to set up Airport Extreme for 11ac and 11n simultaneously?
At present the new Extreme is no better than my previous 2 year old one.
Thank you.
Michael

How to set up Airport Extreme for 11ac and 11n simultaneously?
Assuming that it is operating correctly, 802.11ac and 802.11b/g/n are broadcast simultaneously by default.
Simultaneous dual-band support.
AirPort Extreme features simultaneous dual-band 802.11ac Wi‑Fi. That means it transmits at both the 2.4GHz and 5GHz frequencies at the same time. So no matter which band your wireless devices use, they’ll automatically connect to the best available band for the fastest possible performance.
That is advertising. The real information is usually found in the small and hard to read footnotes:
Based on theoretical peak speeds. Actual speeds will be lower.
AirPort Extreme is based on an IEEE 802.11ac draft specification. Performance based on comparison with Apple’s 802.11n products. Comparison assumes AirPort Extreme network with 802.11ac-enabled computer. Speed and range will be less if an 802.11a/b/g product joins the network. Accessing the wireless network requires a Wi‑Fi-enabled device. Actual speed will vary based on range, connection rate, site conditions, size of network, and other factors. Range will vary with site conditions.
Since the 802.11ac signal is being broadcast only using the 5 GHz band, some users report that they have had better results by using the option to assign a different name to the 5 GHz band, and then pointing their Mac to that specific signal or network. You may want to try that option.
But first as a test, please locate the MacBook Pro about 10-15 feet or 3-4 meters from the AirPort Extreme with clear line-of-sight between the two devices. Restart both the AirPort Extreme and the Macbook Pro and then check to see if the Mac is connected to an 802.11ac signal.
If not, please power off your other wireless devices...computers, mobile devices, etc. temporarily, and try the same test again.
Please report on your results.

How to set a default value for particular field in SRM PO Portal

Dear Gurus,
Im desparetly need a help in web dynpro on how to set a default value for a field(flag) in PO header tab in portal.
My requirement is whenever the user press the edit button in PO screen,automatically a flag field should be set as abap_false.
I dont think this will handle in check badi or change badi. i tried this part in onbuttonpressed overwriteexit in CNR_VIEW views,i can get the function EDIT in debugging mode,but dont know how to proceed further.....
Many of them suggested to go with get attribute and set attribute for changing any particular field in web dynpro,but im not very familiar in using those get and set attributes.I request you people can give me sample code on how to identify my target field in the node and set the values while pressing EDIT Button.
Thanks in advance...
Regards,
Sathish

Dear Laurent,
Thanks for your response,
But i searched in enhancement spot of WD_BADI, but couldnt get the exact way to change the coding,
My real requirement is, that particular flag should be enable and disable dynamically by checking a condition in my header values.So in that case i dont know how to proceed further to handle in the PO screen.
Kinly guide me how to get the particular node of field in the Purchase order screen.
Thanks you in advance,
Sorry for the inconvenience if any
Regards,
sathish

How to set the AS2 fileName for outbound Functional Ack 997 auto generated by Oracle B2B

Hi Friends,
How to set the AS2 fileName for outbound Functional Ack 997 auto generated by Oracle B2B.
External Trading Partner is sending the EDI 856 via AS2 URL to our Oracle B2B Server.
In the inbound 856 agreement, we have checked the option of Funtional Ack and also Functiona Ack handled by B2B is yes.
We have the outbound agreement which is sending that Functional ack 997 (auto generated by oracle b2b) and we have specified the Outbound AS2 channel of the Partner.
997 doc is being sent to external partner using AS2 channel, but the filename is generating as '40101'.
Please can you let me know how to set the AS2 fileName for outbound Functional Ack 997 auto generated by Oracle B2B.
Appreciate your valuable answers!!
Thanks,
Amirineni

Amirineni,
AFAIK, there is no option to set the file name when the 997 is generated automatically by B2B.
Alternatively, if this is a must requirement, you can generate the FA from backend and send to B2B with MSG_TYPE =9. In this case, you can set the header with filename (How to set the actionname property in B2B 11g)

Sun ONE Studio 4 aka Forte: How to set the output path for classes ?

Help !
Beginner's question:
Sun ONE Studio 4 aka Forte:
How to set the output path for classes ?
As default, the class files are created in the same directory as the
sources.
In opposite, both JBuilder and Together support that there is a tree
with the sources and another tree with the classes.
The first answer I got was "not possible with Forte, but just if you write your own "ANT Build script" !
a) Please point me to a ready-to-use ANT script for this purpose, if such is available
b) Is using ANT instead of the MAKE as comfortable ? Besides the separation of sourcecode and classes, I would like to keep everything else to be the same, i.e. I don�t want to edit the ANT file if I enlarge the project by directories or files.
Tia
Sincerely
Rolf

You can set S1S's options to place newly created .class files in a specific location.
Identify the compiler that is being used - Open the S1S's Tools/Options window, expand Editing and select Java Sources. Note the Default Compiler value. (If it's one if the Ant options, you use Ant to specify this option, not S1S.)
Open the S1S's Tools/Options window, expand Building/Compiler Types and select the appropriate compiler.
The Properties tab of the compiler has the property Target, which sets the filesystem where the compiler output is directed. If you choose <not set>, the .class files are written to their source directory.
When you set the Target, your change affects all classes that use this compiler.
Very few options can't be set in S1S; the challenge is finding out where they're set!

How can i write the trigger for Global Temporary Table

Hi Grus,
How can i write the trigger for Global Temporary Table.
I was created the GTT with trigger using the below script .
CREATE GLOBAL TEMPORARY TABLE GLOBAL_TEMP
EMP_C_NAME VARCHAR2(20 BYTE)
ON COMMIT PRESERVE ROWS;
CREATE OR REPLACE TRIGGER TRI_GLOBAL_TEMP
BEFORE DELETE OR UPDATE OR INSERT
ON GLOBAL_TEMP
REFERENCING NEW AS NEW OLD AS OLD
FOR EACH ROW
BEGIN
INSERT INTO EMPNAME VALUES (:OLD.EMP_C_NAME);
END;
trigger was create successfully, but the wouldn't insert into to EMPNAME Table..
Please guide whether am correct or not? if not kindly give a correct syntax with example
Thanks in Advance,
Arun M M

BEGIN
INSERT INTO EMPNAME VALUES (:OLD.EMP_C_NAME);
END;
you are referencing old value in insert stmt.
BEGIN
INSERT INTO EMPNAME VALUES (:new.EMP_C_NAME);
END;then run ur application it works fine...
CREATE GLOBAL TEMPORARY TABLE GLOBAL_TEMP
EMP_C_NAME VARCHAR2(20 BYTE)
ON COMMIT PRESERVE ROWS;
CREATE OR REPLACE TRIGGER TRI_GLOBAL_TEMP
BEFORE DELETE OR UPDATE OR INSERT
ON GLOBAL_TEMP
REFERENCING NEW AS NEW OLD AS OLD
FOR EACH ROW
BEGIN
dbms_output.put_line(:OLD.EMP_C_NAME||'yahoo');
INSERT INTO EMPNAME VALUES (:new.EMP_C_NAME);
dbms_output.put_line(:OLD.EMP_C_NAME);
END;
create table EMPNAME as select * from GLOBAL_TEMP where 1=2
insert into GLOBAL_TEMP values('fgfdgd');
commit;
select * from GLOBAL_TEMP;
select * from EMPNAME;
output:
1 rows inserted
commit succeeded.
EMP_C_NAME
fgfdgd
1 rows selected
EMP_C_NAME
fgfdgd
1 rows selectedgot it Arun
Edited by: OraclePLSQL on Dec 28, 2010 6:07 PM

I want to know that i have recently create an apple id, i want to know that how i can use this id for gsx(without paid) or how to use this id for knowlaged

i want to know that i have recently create an apple id, i want to know that how i can use this id for gsx(without paid) or how to use this id for knowlaged
pls give braef intro about all this things, i have searched on sites but i am not getting exact thing and meaning pls help
and i wnat to complete hardware exam of mac what should i do
thanks
vicckey

GSX, if you're referring to Apple's service by that name, is available only to employees of Apple-authorized service providers or self-servicing accounts. Unless you are employed by such an organization, you cannot access GSX. If you are employed by such an organization, they should set you up and give you the appropriate login information.
If you are interested in becoming a certified Apple hardware technician, you can find information here:
http://training.apple.com/certification/acmt
Please note, though, that certification does not in and of itself give you access to any of the Apple resouces for support organizations; diagnostic tools, parts ordering, etc. You again must be employed by an authorized Apple support provider before you can gain such access.
I have no idea what "knowlaged" might be.
Regards.

How to set a fixed width for a box

Hi there,
Struggling here.... must admit.
I need a solution whereby I can set a fixed width for a box that is grouping two buttons. I suppose generally, I want to know how to set a fixed width for anything element.
See the picture below. I want the two buttons to stay the same distance apart, and I want the grouped buttons to stay the same distance from the right edge of the window, even as a user resizes the window.
This is what happens when you reduce the size of the window .....
I would like to stop this from happening.
I can't figure out how accomplish keeping the parent div a fixed width, and a fixed position from the right side of the window, so the buttons won't overlap.
Perhaps I'm doing the whole thing wrong.
I mean, is there a way to accomplish this without grouping the buttons? That is, make the buttons fixed width, fixed distance apart from each other, and fixed distance from the right side of the window, even as the user resizes the page?
I am trying to accomplish this using the Min/Max width settings, but given that there are so many different units to choose from, and the fact that when I place a button or box on the screen, it seems to be creating that button or box with a percentage-based width, I don't know how many pixels to set it to.... sigh....
Many thanks in advance for your help.
Sam

Okay after much futzing I figured out at least part of the solution I need, but if someone knows of a more efficent way to do this please let me know.
I set a fixed minimum width in pixels for both of the buttons at 156px.
I then made the left button float left and the right button float right.
I then made the parent div for the buttons float right.
That made the buttons stay the same size.
The only thing I need to figure out how to do now is make the parent div stay a consistent distance in pixels from the right. I tried setting a right margin but that didn't work. As you size the window down, the div gets closer to the edge, until it passes it.

How to set & use digital trigger for AIN on a DAQmx?

Similar Messages

Maybe you are looking for