How to setup a PAC proxy on the playbook ?

Anyone know how to setup a PAC proxy on the playbook ? Thx

AGirl71985 wrote:
Hi
I have been trying to setup the mobile hotspot on my phone and haven't been able to find any instructions on how to do this. If anyone can tell me how it would be greatly appreciated. Thanks!
Amanda
Ha Amanda! First, you'll want to make sure your line has been provisioned for Mobile Hotspot service. You can add the feature to allow you to share up to 2 GB of data for 5 other devices for $20.00 per month. Once that is confirmed, please follow these steps to set up your device's mobile hotspot:
Settings> Wireless & Networks> Tethering & Portable hotspot> Portable Wi-Fi hotspot settings> check mark next to Portable Wi-Fi hotspot. This will disable all other data access so that the data usage is allocated correctly. When finished using your Xperia Play as a hotspot, remove the check mark from Portable Wi-Fi hotspot.

Similar Messages

How to setup a guest network when the dialogue boxes do not show up in AirPort Utility 6.1

How do I setup a guest network when the dialogue boxes do not show up in AirPort Utility 6.1?
I see screenshots where there are boxes to 'enable' guest network but these simply do not apear on the Wireless tab in AirPort Utility

I now have a guest account, thanks to you!
I did the factory reset and was able to set up the guest account.
There were 3 problems, all of which I was able to solve.
The first problem was connect to Ethernet, which I selected by WAN port, as shown in the first screen shot. This page used to read just Ethernet and the Bridge Mode.
The second problem was whether to share a range of addresses or share a public IP address. I selected share a public IP address as shown in the first screen shot. I had tried the range of IP addresses in my earlier attempts, the ones that failed. Hopefully this will have no effect.
I have forgotten what the third problem was - only excuse is a few too many flavored drinks. I didn't have any problems solving it though.
What is really weird is I can log on to Guest and use on my iPad (first generation), my wife's iPod Touch (third generation), and my wife's 2011 MacBook Pro. I can't log onto Guest on my 2008 iMac, even after a restart. I get the image below.
Since I don't lug my iMac around a lot and it is connected by Ethernet, while my little make it right brain says figure this out, I am not going to worry about it.
Thank you again for your time and patience in helping me solve this.
Eric Root

How to setup BB10 contact to link to Playbook Video app?

I have a BB Passport device and one of my contacts has a Playbook Video link enabled. I am trying to recreate this for another user but nothing works. How do I create a BB10 contact to enable the Playbook Video link to a user with (only) a BB Playbook. I have the user's PIN and Blackberry ID. Thanks!

If you use buttons instead, it is possible to script adding the actions that you want. It involves creating a properly constructed FDF, saving it, and then importing it into the document. Buttons can be made to appear just like links. For more information, see: http://www.planetpdf.com/developer/article.asp?ContentID=6338

How to setup a Mobile Hotspot on the Xperia Play?

Hi
I have been trying to setup the mobile hotspot on my phone and haven't been able to find any instructions on how to do this. If anyone can tell me how it would be greatly appreciated. Thanks!
Amanda

AGirl71985 wrote:
Hi
I have been trying to setup the mobile hotspot on my phone and haven't been able to find any instructions on how to do this. If anyone can tell me how it would be greatly appreciated. Thanks!
Amanda
Ha Amanda! First, you'll want to make sure your line has been provisioned for Mobile Hotspot service. You can add the feature to allow you to share up to 2 GB of data for 5 other devices for $20.00 per month. Once that is confirmed, please follow these steps to set up your device's mobile hotspot:
Settings> Wireless & Networks> Tethering & Portable hotspot> Portable Wi-Fi hotspot settings> check mark next to Portable Wi-Fi hotspot. This will disable all other data access so that the data usage is allocated correctly. When finished using your Xperia Play as a hotspot, remove the check mark from Portable Wi-Fi hotspot.

How to make an OSB proxy to the server responding with application/json?

Hi,
My question is related to unfortunately unanswered question: Re: OSB and Oracle Maps
Big picture: There is a Jetty server on local network with SpringMVC controllers which respond with JSON. The only way to communicate from frontend application to that server is through the OSB. So OSB should work as transparent proxy, passing headers and respond with original JSON message.
I tried to build such proxy, following some blogs entries. Proxy worked for the REST services based on XML, but when I go to the JSON business service I get stuck.
I think that business service to communicate with JSON server should be a Messaging Service, with Response Type: Text and Request Type: None.
All headers should be passed (Outbound request) so the JSON server receives them in same state as frontend send.
Business service should be invoked from 'Service Callout' because I don't need any asynchronous calls, or routing - just call the business service endpoint, which will call JSON server and pass the response.
There are some problems in which I stepped into when tried this approach:
1. When using Request Type: None the Service Callout give me an error of type:
A callout cannot invoke a one-way operation
When switching Request Type to Text I get it working, but some services on JSON server which operates only on GET method stop work (because switching to Text automatically require to use POST method, which is obvious but not necessary in my case).
2. Even with above modification I cannot get the response from business service - I guess it's because the JSON response isn't wrapped into any XML elements. So in Service Callout any logger prints the message on Request side, but anything is written by Response logger inside the Service Callout. The browser which launch the Proxy Service also answers with:
HTTP 500 (Internal Server Error)
and I don't see any errors in logs, last message is from Request logger inside Service Callout.
3. Business Service itself seems to work - here is an output from 'Run on Server':
Business Service Testing - SampleJSON
Request Document
Response Document
{"models":[],"success":1}
Response Metadata
<con:metadata xmlns:con="http://www.bea.com/wli/sb/test/config">
<tran:headers xsi:type="http:HttpResponseHeaders" xmlns:http="http://www.bea.com/wli/sb/transports/http" xmlns:tran="http://www.bea.com/wli/sb/transports" xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance">
<http:Content-Length>696</http:Content-Length>
<http:Content-Type>application/json;charset=ISO-8859-1</http:Content-Type>
<http:Server>Jetty(7.4.2.v20110526)</http:Server>
</tran:headers>
<tran:response-code xmlns:tran="http://www.bea.com/wli/sb/transports">0</tran:response-code>
<tran:response-message xmlns:tran="http://www.bea.com/wli/sb/transports">OK</tran:response-message>
<tran:encoding xmlns:tran="http://www.bea.com/wli/sb/transports">ISO-8859-1</tran:encoding>
<http:http-response-code xmlns:http="http://www.bea.com/wli/sb/transports/http">200</http:http-response-code>
</con:metadata>
But when calling it from a service proxy I don't get any logger message on the JSON server, which appears normally when I runs business service tests. So it seems that the request doesn't even reach it.
If anyone has a time to look at this problem I can share the configuration jar ready to import: http://dl.dropbox.com/u/21341604/sample-osb-json/sample-json.jar, to make it working you need change Endpoint URI in SampleJSON.biz.
Thanks in advance for any kind of help or tips,
Adrian

If you are the admin, then use the following command in Terminal:
sudo mkdir /.nameOfFolder
Replace nameOfFolder with the name you want. The sudo will prompt you for your admin password.

How to setup BPEL JNDI connection on the application server

Hi
Can anyone tell me how to write a JNDI connection for my BPEL process? Currently we are invoking all my BPEL processes from a property file, but i need to call my BPEL process thru JNDI connection. Is it possible? If yes then How?
Has anyone got any idea? Please let me know
BTW, you need more clarification on the question, let me know please.
Thanks.
Deepak

Hi Grafl,
Chk this link
Folder creation in AL11 using ABAP program
try this code.This works on UNIX servers
data: unixcom like   rlgrap-filename.
data: begin of tabl occurs 500,
        line(400),
      end of tabl.
dir = unixcom = 'mkdir mydir'. "command to create dir
"to execute the unix command
call 'SYSTEM' id 'COMMAND' field unixcom
                  id 'TAB' field tabl[].
<b>Reward Points if Useful</b>
Regards
Gokul

How to setup a usb printer on the usb port of a network storage drive

I have searched the forums and dont see any real info on this..
I have a usb based officejet 7590 , winxp, and a iomega home media network storage drive
the printer works fine when I install it on the local usb port of the laptop
BUT
its not clear how to connect it ot the usb port of the network drive.
DO I have to resinstall it as a network printer?
DO I have to resinstall device drivers if I already installed it as a usb printer for the local port?
Can I use the scan/fax functions if I do it right?
thx!

OK, I will use it as a bookstand...
Since I obviously don't know enough about networks I will stay away from 'professional' products like the Cisco products.
The user interface and the documentation of these products are clearly made by nerds for nerds...
Thanks for your help.
Paul

Don't know how to setup a simple VLAN on the RVS4000

I'm sure it is my lack of knowledge of networks, but even after reading the manual (!) I don't understand how I can set-up a simple VLAN on my new RVS4000.
On my good old DrayTek it's very easy: it shows me a matrix of check boxes and all I have to do is click the ones that correspond to ports that can 'see' eachother. Something like this:
               Port 1   Port 2   Port 3   Port 4
VLAN 1    x                          x
VLAN 2                      x        x
VLAN 3             x                 x
VLAN 4
So port 1-3 can all 'see' port 4 (the Internet router) but they can't 'see' eachother.
Can anyone please show me the steps to take to accomplish this? Thanks a lot in advance!
Paul

OK, I will use it as a bookstand...
Since I obviously don't know enough about networks I will stay away from 'professional' products like the Cisco products.
The user interface and the documentation of these products are clearly made by nerds for nerds...
Thanks for your help.
Paul

How to setup a validation table in the IBM AS400 ?????

I am trying to use the Java studio creator with the IBM AS400
and I am having difficulty setting up a validation table.
I created a totally new DB2 SQL table, with just a couple of columns.
However, when I use it as the validation table to setup the Datasource, I get the following message:
[SQL5016] Qualified object name PMABR not valid.
The ideal validation table exists only for connection validation purposes. Do not use an existing table that has a large number of rows or a table that will be frequently accessed.
any ideas?
thanks a lot

Thanks for rectifying me Howard.
I just read your full article on this too and its very well explained here:
http://www.dizwell.com/prod/node/357
Few lines from your article
It is true, of course, that since Version 8.0 Oracle has provided the ability to create a Keep Pool in the Buffer Cache, which certainly sounds like it can do the job... especially since that word 'keep' is used again. But a keep pool is merely a segregated part of the buffer cache, into which you direct blocks from particular tables (by creating them, or altering them, with the BUFFER POOL KEEP clause). So you can tuck the blocks from such tables out of the way, into their own part of the buffer cache... but that is not the same thing as guaranteeing they'll stay there. If you over-populate the Keep Pool, then its LRU mechanism will kick in and age its contents out just as efficiently as an unsegregated buffer cache would.
Functionally, therefore, there can be no guarantees. The best you can do is create a sufficiently large Keep Pool, and then choose the tables that will use it with care such that they donâ€™t swamp themselves, and start causing each other to age out back to disk.
Thanks and Regards

How to setup a job to change the backup ID

Hi,
We know that SAP hana's backup will use the same backup file names once the configuration is done for backup.
To avoid overwritting the previous backup files, we have following options (note that we are using "file" not "backint")
1) rename the generated backup files after the backup is done;
or
2) move the generated backup files to another location.
We want to achieve above goals by
1) OS level cron jobs
or
2) an xsjob in xsengine.
The challenge is that cron can only be started at predefined time while the the backup job can take various time to finish.
Therefore we wonder if xsenigin can provide any event-dependent job scheduling to help with this?
Questions:
1) is there any way to detect backup status automatically at OS level?
2) is there any 3rd party scheduler for Hana?
Thanks!

Actually you can assign unique names for backups.
Suppose we have $DAY = 'Friday'
hdbsql -n localhost -i [instance] -u [db user] -p [passwd] "BACKUP DATA USING FILE ('$DAY')"
will generate files like Friday_databackup_0_1, Friday_databackup_1_1 etc

How to Setup User Folders Automatically when the user is being created

Hi All
I am setting up a new Windows Server 2012 R2 Standard Edition with Full/GUI install.
Q.1. Is there a way to create User Folders on Data Drive (D: Drive - OS is installed on C) automatically as I create Users?
Q.2. Additionally can these folders be assigned appropriate permissions automatically?
Q.3.What is the best approach If appropirate permissions are not assigned automatically. I have drive D: as a share with Full permissions to all. Is there a better way.
Thanks
Respectfully
Jamal

Hi,
Not sure you mean local computers or domain environment. In domain, we can create folder redirection GPO.
With this policy we can redirect folder to a shared folder or another local drive.
For your information:
Configuring Folder Redirection
http://technet.microsoft.com/library/cc786749.aspx
Security Recommendations for Folder Redirection
http://msdn.microsoft.com/en-us/library/cc736916(v=ws.10).aspx
Hope this helps.

How to setup the From header in fullname and email address format

when I sent mail from the messaging express , the mail that I sent cannot show the sender in the fullname and email address format. I use webmail and other mail client . It show only email address. I don't know how to setup this . I use the SUN JES messaging server 6.0 SP1 .

exactly so.
in general, for any configutil setting:
0=off=no
1=yes=on

How to setup to trigger an event when choose the value from cookie

Hi,
I define an firepartialaction event for the messageTextinput, this event can be triggered when the user key in the via keyboard. but failed to be triggered when the user choose the value from the cookie. How to setup or program to trigger the event even the user choose the value from the cookie?
Best Regards,
Jiang

Hi,
so the next missing information is what the event is that you expect to fire. If the cookie value is displayed in a list then John is correct and you populate the input field behind the scenes in which case e.g. no ValueChange listener fires or autoSubmit action is issued as you don't update the data through the UI component
Frank

How to Setup Historical DSC Database on a standalone Server

Hey @all,
I am looking for documentation how to setup a standalone server for the DSC Module(Ver. 8) Historical Database.
My aim is to log all data to this server. The Server will be running Win2K.
Do I have to install the complete Labview 8 software and the DSC Module?
Does a walkthrough exist how to setup a DSC server?
Thx!
Carsten

After installing the runtime you should only have to reboot the computer in order to get the citadel service running. At the point, for citadel purposes, this machine will behave as though you had the DSC development system installed. The 8.0 runtime has no setup requirements...it should only need to be installed. Unlike previous versions, 8.0 requires you to build your application into an executable and the runtime should be invisible to you once you install it. If this is not the case, please post about it so it can be looked at.
If you have specific questions, please post them and I will either try and help you find the answers, get them posted, or answer them myself.
Regards,
Robert

How to setup a global artwork for a TV Show

Hi, I've a TV Show composed by 45 episodes where each one have his artwork but I don't know how to setup a global artwork for the TITLE of the TV Show while retaining the 45s artworks.
ie. when watching the Tv Shows (library on iTunes) I would like to see the global artwork of the Tv Show that is different of the other 45s episodes contained.
Bye, Roberto.

Sorry, I don't believe that you have had a good look at the Foundation framework. I'll now hold your hand while we go through the basics.
Here is the specific page http://foundation.zurb.com/docs/components/grid.html
The default values are
Em-base : 16px
Row width: 62.5em (62.5em x 16px = 1000px)
Columns per row: 12
These and other default values can be changed. The fact of the matter is that if you stipulate a section width of 2 or 3 or 12 columns, the widths will automatically be calculated for you.
In your case, if you want 7 columns, all you need to do is change the number of columns per row and the rest is done for you.

How to setup a PAC proxy on the playbook ?

Similar Messages

Maybe you are looking for