How to setup a wireless printer
I was wandering if anyone out there knows how to setup a wireless printer without spending a lot of money. I have a dell photo 962 printer and a wrt54g router. I have tried to setup the printer on my laptop but it will not let me do so unless I connect it directly to the printer. My computers are running windows xp. Thanks for your help.
well for that you need to setup a printer as network printer, if your printer have networking capabilities...if not then you need to buy print server...
Similar Messages
-
How To Disable A Wireless Printer Network Setting (SSID) On A HP L7700
How To Disable A Wireless Printer Network Setting (SSID) On A HP L7700 Previousley Set Up
Hello @flamek2,
Welcome to the HP forums.
I understand that you are trying to disable the wireless settings on your Officejet pro L7700 series printer.
I would like to help.
To erase the printers network information, go into the Setup menu.
Then go into the Network menu.
Select restore network defaults.
If you want to disable wireless altogether, then go into setup and choose network.
Select wireless radio, and turn it off.
Hope this helps you.
If you need any additional assistance please let me know.
Aardvark1
I work on behalf of HP
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos Thumbs Up" on the right to say “Thanks” for helping! -
How can I get wireless printing with my ipad?
How can I get wireless printing with my ipad?
Best way is to use an AirPrint compatible printer:
http://support.apple.com/kb/HT4356
If your printer is not AirPrint compatible, you might want to take a look at Printopia.
http://www.ecamm.com/mac/printopia/ -
How to add a wireless printer to airprint?
How to add a wireless printer to airprint?
Only the printer manufacturers can add AirPrint support to their printers via firmware updates. If your printer isn't listed on this page as supporting AirPrint, then does the manufacturer have their own app in the app store that supports it ? If not then there are third-party printer apps such a PrintCentral Pro and Print n Share which might work with it.
-
How does a PC wirelessly print on a printer connected to an airport express
HI
how does a PC wirelessly print on a printer connected to an airport express?
my husband has a PC and I'm fed up with him using my macbook for printing
thanksYou can install [bonjour for Windows|http://support.apple.com/downloads/BonjourforWindows] or use [IP printing|http://www.macosxhints.com/article.php?story=2003072510530643]
-
How do I add wireless printer or Direct tv
How do I add wireless printer or Direct tv
These devices would be added the same way that any other wireless device is added as a client to a network......
1) Scan to select the network
2) Enter the wireless network password
Keep in mind that DirecTV cannot connect to a wireless network if there are special characters.....like an apostrophe, asterisk, dollar sign, etc......in the wireless network name.
So if your wireless network is named something like Ernestomelia's Wireless Network, DirecTV will not be able to to connect. Instead, the network should read something like ernestomelia network. A shorter name with no spaces would be better.
Your printer might have similar requirements, but you did not provide the make or model number of the device....so we don't have much to go on here. In general, you would want to contact support at the printer manufacturer for more specific information. -
how do i setup my hp deskjet 3050 all-in-one printer for wireless printing my operating system is windows7
Unplug the USB cable. Now go to Start > All Programs > Hewlett-Packard > Deskjet 3050 > Add a Device. Run the program and choose Wireless as the installation type.
Follow the directions. It will ask you to connect a USB cable temporarily. Do not connect until it asks and remove it when it tells you.
Finally, when you are done, go to Control Panel > Devices & Printers and delete the USB instance of the printer so you don't get confused when printing.
Say thanks by clicking "Kudos" "thumbs up" in the post that helped you.
I am employed by HP -
How to setup a network printer via http
I have a router with a USB printer attached to it. It looks like this:
Printer status: Ready
Printer location: http://192.168.2.1:1631/printers/My_Printer
In Windows you setup a network printer and the printers address is the http address above. How do you add this type of printer in the printer setup utility on Mac OSX 10.4.11 and 10.5.x?For OS X 10.5, you use the following settings
As mentioned by bdaqua, open Print & Fax and click the IP icon and then select IPP from the top drop menu. Then in the Address field just enter the IP address; don't enter the leading 'http://' and don't enter the :631 (the mere fact that you have selected the IPP protocol means that it will communicate on port 631)
Then in the queue field you can enter printers/My_Printer, although some router perform a translation for the shared printer so you only need to enter the shared printer name in the queue field.
As for the name and location fields, these are just free text for the local user and have no bearing on the queue details.
And as for 10.4 I have no idea or way to test this at home. But if you use a mix of mine and bdaqua's information you should be okay. -
How to install HP wireless printer
Please can you tell me how to install an HP wireless printer to my Ipad2 - I have managed to install the printer to my IMac. Thank you.
Hi the tone of that answer is a litte strong , but I hate to correct you the app mentioned by Divonex works well enough used it many times iPad to hp printer . Took 3 mins to install works a dream , means I can work all my office docs into google docs and print off, havent tried drop box yet . But I' ll post when I do so . Do try to be nice , we are all learning from each other . Peace.
-
How to configure a wireless printer
Hello guys,
I've just got a new MBP 13' with retina display.
I do have also a CANON PIXMA printer with wireless device (it says enabled for air print and compatible with Mac) thus I would like to configure and add it to my MBP and possibly to my IPAD and IPHONE.
I have a wireless network at home and it works fine with my MBP.
I thank you all in advance for the help provided.
RobertoThere is NO Wireless Printing, that is a Misnomer. You print over your network. It doesn't matter how the printer or the computer connects to your network, it could be by WiFi or over an Ethernet cable, both of them have to be connected to the same LAN (Local Area Network).
So the first step is to connect the Printer to your home LAN. It has to get an IP address from your router or modem/router combo box used to connect to the internet. Once that is done then you can connect To the printer from your computer that is connected to that same LAN. -
How to make a wireless printer?
I have laptop with wifi, and have a wireless router ,a HP color Laserjet 1515n. now I want to put the printer in the other room far from the router and laptop. how can I make a wireless printer(no wire connect to the router)? shall I buy a device? what kind device? thank you!
This question was solved.
View Solution.As far as I can tell your printer only has a USB connection, right?
If so, you may be able to buy a wireless print server, but they are somewhat difficult to set up. If you buy one, get one the same brand as your wireless router (I don't think HP makes one for this printer from my quick search).
Say thanks by clicking "Kudos" "thumbs up" in the post that helped you.
I am employed by HP -
How to fix single wireless printer showing up as several (bonjour) printers?
I have the following problem with a wireless printer/scanner connected using bonjour (Samsung SCX-3205W):
When using the device in wireless mode, after a period, the single printer shows up in the selection list as tens or even hundreds of seperate printers. Applications showing/selecting printers or scanners slow down dramatically and sometimes stop responding (beach ball rotating for long periods)
Below is an example of what is shown in e.g. printer selection lists (see also attachment):
Samsung SCX 3200 Series (SamsungSCX3205)(28060)
Samsung SCX 3200 Series (SamsungSCX3205)(28061)
Samsung SCX 3200 Series (SamsungSCX3205)(28062)
Samsung SCX 3200 Series (SamsungSCX3205)(28063)
Samsung SCX 3200 Series (SamsungSCX3205)(28064)
Samsung SCX 3200 Series (SamsungSCX3205)(28065)
Samsung SCX 3200 Series (SamsungSCX3205)(28066)
Samsung SCX 3200 Series (SamsungSCX3205)(28067)
Samsung SCX 3200 Series (SamsungSCX3205)(28068)
Samsung SCX 3200 Series (SamsungSCX3205)(xxxxx)
The device works fine using USB or ethernet connection but problems arise when using the wireless connection. After adding the printer using System Preferences / Print & Scan it seems to work fine, atleast for a while. After some time the printer seems to multiply itself in the printer lists (e.g. when adding new printer or using Preview or Image Capture to scan and choosing a network device.)
I'm using OS X 10.7.3 and have the latest drivers for the printer (Samsung SCX 3200 series 1.01.01)
Im connected to the printer through a wireless router/adsl-modem
The problem seems to start (i.e. printer starts to "multiply") after the printer goes into power save mode. (The power save function can't be turned off, only set to max 120min)
Anyone have similar problems with other wireless printers or any idea what might be causing this? Or how I could fix it?
Best regards,
JLI haven't received any replies to the question I recently posted, but one work-around that HP suggested is to use different scanning software. Instead of Image Capture, I used the HP Scan.app that came with my all-in-one printer. I haven't seen those rectangles in my PDFs since switching.
-
Help! Confusion over how to setup intel3945 wireless and rc.conf
Hi,
I'm very confused. I've already read through all the wikis and searched many forum posts. I can't get my wireless intel3945 to work on my dell vostro 1400.
Iwconfig says the wireless card is at wlan0 and dmesg | grep iwl says it has detected it. However, when I try a iwlist wlan0 scan it returns :
wlan0 Interface doesn't support scanning : Network is down
I think the problem is that I don't know how to setup rc.conf correctly or use the command line to test the wireless. Forum posts say many different things on how this is done.
These are the steps I have taken:
uninstalled the ipw3945 and ipw3945-ucode and ipw3945d.
installed iwlwifi and iwlwifi-3945-ucode
in my rc.conf modules, added iwl3945.
I'm not sure how to setup the networking section, this what I have now:
lo="lo 127.0.01"
eth0="dhcp"
wlan0="dhcp"
INTERFACES=(lo etho)
gateway="default gw 192.168.1.1"
ROUTES=(!gateway)
And in my dameons I have 'network'.
How can I scan for networks and connect to them on the commandline? I'd prefer not to use a gui tool because they never work and never tell me why they're not working.
Any help is greatly appreciated!
Cheers!
kilolimaiphitus wrote:
broch wrote:I have ipw3945 and iwl3945 working with wpa2 (or vpn)
(less complicatd than the above)
don't use netcfg2
Why?
no particular reason.
Simply when I configured wireless, netcfg2 wasn't available. Since then it (wireless) works, so not having any problems, I did not modify network setup. Next week or so I am going to install Arch on my daughter's laptop (per her request ) so I will try netcfg2.
So this is what I have for ipw3945 wpa2 or iwl3945 with wpa2
Below you will find a lot of words so read slowly but there is not much actual work
ipw3945 setup
kernel 2.6.23.x (Arch or vanilla)
or
kernel 2.6.24/2.6.24-gitX (patched with ipw3945 patch from gentoo -> compiling separate module for 2.6.24 may fail. if you want kernel patch I can post a link)
for default kernel install Arch packages for ipw3945, ipw3945d, ipw3945-ucode
or
if you want to compile modules, you will also need ieee80211 (first uninstall kernel's default, then install from sources otherwise ieee80211 from sources may refuse to install)
modify /etc/rc.conf
DAEMONS=(.... @ipw3945d @network ....)
that is all you don't need to add ipw3945 to MODULES=(.....)
because ipw3945d will automatically start ipw3945 module
do not list eth1 in network config section:
lo="lo 127.0.0.1"
eth0="dhcp"
INTERFACES=(eth0)
as you see, in my case only eth0 (wired) is listed and eth1 (wireless) is not listed
now you are done with basic network configuration for ipw3945, restart network/computer to bring up ipw3945d/ipw3945
check if modules are up and basic network is set:
#lsmod | grep ipw
#ifconfig -a
or
#iwconfig
if all is o.k. configure
WPA2:
configure router for wpa2
client: basically follow Arch wiki:
configure wpa_supplicant (installed already of course)
#wpa_passphrase your_ssid your_psk
keep terminal window open with created encrypted wpa passphrase and in the second terminal window edit /etc/wpa_supplicant.conf
ctrl_interface=/var/run/wpa_supplicant
network={
ssid="your_ssid"
scan_ssid=1
proto=WPA RSN
key_mgmt=WPA-PSK
pairwise=CCMP TKIP
group=CCMP TKIP
psk=whatever_output_from_wpa_passphrase
Above pairwise and group setup will depend on your router (network capabilities)
almost done:
run
#wpa_supplicant -Bw -Dwext -i eth1 -c/etc/wpa_supplicant.conf
the above assumes that your ipw3945 is set as eth1 (from iwconfig output)
to connect to the network I am using "wireless assistant" http://www.kde-apps.org/content/show.ph … tent=21832
that is all for ipw3945. You may automate network starting/connecting to wpa2 by writing simple script.
iwl3945
--kernel 2.6.23.x
install iwlwifi and iwlwifi-3945-ucode
--kernel 2.6.24.x
install only iwlwifi-3945-ucode as kernel has iwlwifi module incorporated
default iwlwifi does not support LED so I suggest to install something like knemo for kde to show active network icon. The latest iwlwifi does support LED but it is not yet incorporated into 2.6.24 vanilla kernel.
if you have kernel 2.6.23.x with external iwlwifi module
modify /etc/rc.conf
and add iwlwifi to
MODULES=(.....)
nothing else is required.
if you have kernel 2.6.24 with integrated iwlwifi module you don't have to edit /etc/rc.conf
As in the case of ipw3945, I do not list wireless interface (wlan0) in /etc/rc.conf
for kernel 2.6.23.x
load module/restart network or simply restart computer
check if module is up
#lsmod | grep iwl
#iwconfig
or
#ifconfig -a
WPA2
same wpa_supplicant.conf as above, so if you already have it no need for modifications.
start wpa2
#wpa_supplicant -Bw -Dwext -i wlan0 -c/etc/wpa_supplicant.conf
the only difference in the command is wireless interface: wlan0
connect to the network, again I am using "wireless assistant"
vpn
I am using cisco vpn. Client is provided by vpn host, cisco does not provide vpn client for individual download, but you can find it on line.
vpn host will provide pcf file for you
- install vpnclient
- copy your VPN profile (vpn.pcf) to the
/etc/CiscoSystemsVPNClient/Profiles
directory
-- start vpn client
/opt/cisco-vpnclient/bin/vpnclient connect vpn pcf_file_name
provide username and password and off you go
From my experience none of linux gui for vpn works reliably so you will have to resort to the command line.
That is all, a lot of writing, but actual ipw3945 and iwl3945 configuration is straightforward and very short.
Hopefully this will work for you.
forgot to add regarding vpnclient (cisco)
you will have to modify
/etc/init.d/vpnclient_init
line 38 and line 101
replace
/sbin/lsmod
with
/bin/lsmod
Last edited by broch (2008-02-07 15:55:45) -
IBook, Gateway Laptop and 2 printers, how to set up wireless printing?
I have an iBook G4 with an Airport Card, my wife has a Gateway Solo with a wireless card. We have an existing wireless internet connection. We have two Epson printers that we would like to be able to print to wirelessly.
I'm assuming that I need to connect both printers to a wireless router, and I assume it may be another router and not the one we're using for internet. What do I need to do to get both of us to be able to print wirelessly to either printer from our laptops?
Would appreciate some help. Thanks!Well I spent a lot of trial and error getting this to work, however I use the Airport Extreme (white UFO thing) router from apple. From the router that is transmitting your wireless connection, there should be some way to hook up your printer(s) via ethernet cables. If your printers are too far away from the router, you may have to purchase an additional router. My Airport extreme can only utilize one printer at once (yours may be able to have multiple peripherals connected to it). In order to use two, I would have to pruchase an additional airport transmitter (like an Airport Express) and have the 2nd printer wired to that.
The only hangup I had was figuring out why my windows computers didn't see the wireless printer. I needed to have installed Bonjour (Apple's peripheral communication software) on all the computers on the network and it can be downloaded on Apple's support web page. Depending on your router, you may not need to.
Your router, whatever it may be, should work in a similar fashion. Consult your router's manual for the proper connection methods/possibilities. Hope this info helps you some. -
one more day trying to setup the printer 5520 before returning it to the store
Welcome to the forums @kamadevan ,
What exactly are the issues that you are running into when you attempt to setup and install your Photosmart 5520? Please let me know some more information so I can better try to help out.
How is the printer connected (USB/ wireless/ wired/ Bluetooth)?
What is the Operating System of the computer?
Have you tested hardware functionality (made copies)?
Have you tried printing from different programs?
Have you tried uninstalling and reinstalling the software?
What Firewalls and Anti-virus software are installed?
Have you tried disabling or uninstalling them?
Do you see any error codes or numbers, if so, what are they?
Hope you have a great day
R a i n b o w 7000I work on behalf of HP
Click the “Kudos Thumbs Up" at the bottom of this post to say
“Thanks” for helping!
Click “Accept as Solution” if you feel my post solved your issue, it will help others find the solution!
Maybe you are looking for
-
A G4 running/booting off a lacie with TIGER 10.4.7
i have amongst many G5's , a G3 pismo and a G4 400MHZ desktop that i wish to have boot off of and run as if Tiger was their OS. The pismo cant run tiger itself i think but could it boot off of TIGER if that was on an external 7200 firewire HD? could
-
Light leakage question: any replacement iPad 2s ok?
Seems to me that everybody writing about getting replacements is saying the replacements they received are as bad or worse. Just wondering if anybody at all has received a replacement that has been okay.
-
I need a phone # to talk to a real live person about my new photoshop elements 13 PLease??????
-
Exchange Adapter Create Mailbox polling interval?
As part of the Exchange Adapter functionality it checks AD to see if the Exchange attributes are set on the AD user. Depending on your AD configuration it can take some time for those attributes to get populated on all DCs. The behavior of the adapte
-
I am having an alignment issue with a website that I recently built using dreamweaver. http://bacs.myweb.uga.edu There is not an alignment problem on the front page (index.html), but subsequent pages (http://bacs.myweb.uga.edu/currentstudents.html) c