How to setup a wrt54g router as a wireless access point to extend wifi signal from e3200

how do i setup a wrt54g router as a wireless access point to extend wifi signal from e3200 which is broadcasting the internet?
everyone keeps saying to remove the stock firmware and instal the dd-wrt firmare to do this. can i do this with the stock firmware?
any tips to avoid interfearance once setup?

You have to connect both with a cable.

Similar Messages

Converting a BEFW11S4 V.2 router to a wireless access point. Can it be done?

I recently upgraded my home wireless router to an N device. Now, I'd like to use my old B wireless router as an access point to improve coverage on my property. I'd like to place it in a location in my house too distant from the N router to connect it with a cable. Any way to configure the old B router as a wireless access point?
Thanks for any help you can give me.
Dave

yes..u can certainly configure the router as an AP ... follow the steps below :
1)connect the B-router's port 1 to once of the LAN ports of the N-router
2)access the B-router's web ui , using its ip address
3)configure the wireless settings....in case , you want to make a roaming wireless network , the wireless settings on both the router should be same
4)if the ip add of the N-router is 192.168.1.1 , then change the ip add of the B-router to 192.168.1.2 and disable its DHCP server ..

RV325 Router: Adding a wireless access point for wireless printer

Hi all,
I am trying to add a Linksys ea6350 wireless router to the RV 325 router with the goal of having a wireless printer on the network. I can connect wirelessly to the router and access the internet; PC's that are on the wireless router can find the printer and print. However, PCs that connected to the RV via LAN cannot. I am assuming that this has to do with how the traffic from the wireless router is handled and that basically at the moment both routers are functioning as two separate networks.
Is this something that can be remedied from the Cisco router side? Or the Linksys? Or Both?
Thank you

Hi Jow, it sounds like you have this EA router connecting through the WAN port going in to your RV router, that would make the most sense because it would NAT your connection, allowing you to wirelessly connect but your LAN connection to the RV325 not working.
If you want to fix this, move your connect from the EA router on to a "LAN port", disable the DHCP server then make sure it is on the same IP subnet as the RV325 and just let it broadcast the wireless signal. The EA router LAN ports are normal switch port so it will work ok.

Can I disable my Verizon Fios Router Wireless radio, connect it to a switch and use my airport express as my wireless access point connected to an in wall ethernet port?

Here's the deal. I have a Verizon Fios MI424WR router. My house has CAT5 throughout the house. The media panel is located in the garage. I want to take the Verizon Fios Router and cannot it in the media panel so I can connect a switch to it, that way, all my CAT5 can fire throughout the house. Verizon being Verizon decided to connect the router directly in the office.
Can I go this route (Router in media panel, switch cross connect to it) and use Airport Express, connected to one of the in-wall CAT5 ports in my house and then set it up as my wireless access point to provide wifi to my portable devices (iPad, iPhone, Macbook)? Is this possible? Will Airport Express comminicate with my verizon router via ethernet in-wall? Do I have to turn off the wireless radio in the Verizon router? Any help would be greatly appreciated!

That is right, by hard wired I was just making clear wired vs wireless attachment. AirPort family of devices will only act in a repeater mode with their own family members, not FiOS routers. they have to be wired to work.
There are some useful docs you can download from Apple, Support, Manuals, Peripherals, AirPort (just follow thos links from the Support button on the top bar):
Apple AirPort Networks
Designing AirPort Networks
AirPort Express Setup Guide
The last has a diagram of what you are trying to do, though without the house wiring, etc., but the basic principle.

How to Turn Your Mac into a Wireless Access Point?

How do i Turn my Mac into a Wireless Access Point in my home? even a link to where it tells me step by step would be great thanks!

Click here and follow the instructions.
(44739)

How to setup a second router?

Does anyone know if there are instructtions somewhere that will tell me how to setup a second router in front of my Actiontec MI424?
I am trying to use a Sonos music system through my computer and it has been recommended to me that I try to use a different router in front of the Actiontec.
Any help would be appreciated.
Thanks.

mniven wrote:
Does anyone know if there are instructtions somewhere that will tell me how to setup a second router in front of my Actiontec MI424?
I am trying to use a Sonos music system through my computer and it has been recommended to me that I try to use a different router in front of the Actiontec.
Any help would be appreciated.
Thanks.
Strange thing to recommend, did they say why?
The Sonos system appears to be just an in house music distribution system that besides accessing in house dvices can also access web based music sources. Are you trying to stream audio via RTSP? as I see another post here regarding what looks like packet fragmentation issues when accessing RTSP thru an Actiontec router.

How to setup the Linksys router E4200 DD-WRT for WVC54GCA

I don't know how to setup the Linksys router E4200 DD-WRT for WVC54GCA. The DD-WRT is very complcated. Please help!!!!! Also, I have used the TZO.com for the DDNS. Should I setup the DDNS for DD-WRT router??? I used the DDNS for my old model router before. Thanks.
Solved!
Go to Solution.

Hi majekho, that is best be answered by support from the developers at the DD-WRT forums.
The Search Function is your friend.... and Google too.
How to Secure your Network
How to Upgrade Routers Firmware
Setting-Up a Router with DSL Internet Service
Setting-Up a Router with Cable Internet Service
How to Hard Reset or 30/30/30 your Router

Can WRT54G be setup as a Wireless Access Point?

Does anyone know how to setup a router (WRT54G) to connect to other routers using a wireless connection and function as either a wireless access point or another router using the main router for it's internet and network connection?

you cannot get the WRT to connect wireless to any device as it is an access point.
However this same thing will work wired. All you need to do is change the LAN ip of the WRT to 192.168.1.50 from 192.168.1.1 and disable the DHCP on the WRT.
Connect both devices LAN to LAN , do not use the internet port of the WRT.

How can I set up a guest access point with a Time Capsule and an Airport Extreme? I am using a Telus router with the Time Capsule used as a wireless access point (bridge mode). I don't want the guest access point to have access to my network.

How can I set up a guest access point with a Time Capsule and an Airport Extreme? I am using a Telus router with the Time Capsule used as a wireless access point (bridge mode). I don't want the guest access point to have access to my network.

The Guest Network function of the Time Capsule and AirPort Extreme cannot be enabled when the device is in Bridge Mode. Unfortunately, with another router...the Telus...upstream on your network, Bridge Mode is indicated as the correct setting for all other routers on the network.
If you can replace the Telus gateway with a simple modem (that performs no routing functions), you should be able to configure either the Time Capsule or the AirPort Extreme....whichever is connected to the modem....to provide a Guest Network.

How to setup a password protection in my wireless airPort?

How to setup a password protection to my wireless AirPort?

To configure the AirPort base station for wireless security, you will need to use the AirPort Utility.
AirPort Utility > Select the AirPort > Manual Setup > AirPort > Wireless tab
Wireless Security: <None | WEP (Transitional Security Network) | WPA/WPA2 Personal | WPA2 Personal>
Wireless Password: <enter your desired password>
Verify Password: <reenter your desired password>

How to Setup WRITTEN as a wireless access point to work with WRITTEN

Hi,
I had a router WRITTEN which was not covering the whole space in my house. I was looking for a N wireless access point or a range extender.
The shop seller convinced me to buy WRITTEN saying that the Dual N will fix my problem.
well it did not. The reception in some locations is still poor.
the same reseller advised me to use the 350N as a wireless access point instead of buying one. The question is how to do it.
I am thinking about the following:
1- Have the WRITTEN installed next to the internet modem connect to the modem by cable
2- in another room have the WRITTEN (approx 20 meters away) not connected by a cable to the WRITTEN
3- When using the laptop in the weak reception area, I try to connect wirelessly to WRITTEN which should be also connected wirelessly to the WRITTEN
Would that be possible. I hope so since there is no way to have a cable connecting the 350N and 610N due to many reasons
appreciate your help in adance

I am sorry but the spelling checker repalced my router names to another word
the correct text is:
I had a router WRT350N which was not covering the whole space in my house. I was looking for a N wireless access point or a range extender.
The shop seller convinced me to buy WRT610N saying that the Dual N will fix my problem.
well it did not. The reception in some locations is still poor.
the same reseller advised me to use the 350N as a wireless access point instead of buying one. The question is how to do it.
I am thinking about the following:
1- Have the WRT610N installed next to the internet modem connect to the modem by cable
2- in another room have the WRIT350N (approx 20 meters away) not connected by a cable to the WRT610N
3- When using the laptop in the weak reception area, I try to connect wirelessly to WRT350N which should be also connected wirelessly to the WRT610N
Would that be possible. I hope so since there is no way to have a cable connecting the 350N and 610N due to many reasons
appreciate your help in adance

How to enable wireless access point for WRT300N

From product data, "First, there’s the Wireless Access Point, which lets you connect to the network without wires."
I already have a WRT54GX-V2 setup to modem.
My intention for this WRT300N is to extend the network connectivity without any lan cable running along my house for those devices which only support LAN wire.
Try to search/google around, there is no hint/help to configure AP in WRT300N.
May I know how should I configure WRT300N so that i will be as an access point to WRT45GX-V2 without any wired connection between these 2 router.
Thanks.

Is that mean I can do that with WAP4400N only if we want to sustain wireless-N mode?
Yes. With standard firmware, yes. (If there is a N WET wireless bridge, that would do it, too, of course)
Is there any way to configure WRT300N to connect to WRT54GX by wireless?
It may be possible if you can flash third party firmware like dd-wrt on the router (either one). I would suggest to check the dd-wrt wiki for notes on which routers are supported and which not. However, a bad flash may brick your router and it is probably not covered by warranty then...
If use wired connection, do I need to change any configuration vs. default factory setup?
If you can run a wire I would suggest this setup.
EDIT: as Ricewind correctly noted, the Linksys WETs are the wireless bridges. The WRE is a repeater.
Message Edited by gv on 04-13-2008 02:25 PM

I have an airport extreme and express, if I use the extreme as a base station connected to my old router can I use the express to extend the signal while also creating a new network that only I can use?

I have an airport extreme and express, if I use the extreme as a base station connected to my old router can I use the express to extend the signal while also creating a new network that only I can use? Essentially having two wifi connection off the same network? If so how do I set this up?

Extending using a wireless connection always results in a performance compromise.
If the Express is going to extend using a wireless connection, then the Express will need to be located about half way between the AirPort Extreme and the general area where you need more wireless coverage. The more that you have line-of-sight between the Extreme and Express, the better the network will operate.
Remember......the Express can only "extend" the quality and signal speed that it receives, so it needs to be located where it can get a very good signal from the Extreme. Although Apple cleverly uses the term "extend", a more accurate term for the Express would be "repeater".
If the Express will extend by connecting to the Extreme using a permanent, wired Ethernet cable connection......highly recommended for best performance.....then the Express can be located exactly where you need more wireless coverage. There is no signal loss at all through the Ethernet cable, so the Express gets a full speed signal no matter where it might be located.
Post back to let us know which way to you want to go.

How do i set up a wireless access point with ny time capsule

I am using a new Airport Extreme and want to utilize my older TC to create a wireless access point or maybe an aditional router using the same newtwork. What are the steps to set this up?
Thanks
Alamo

You will first need to perform a Factory Default Reset on the Time Capsule.
Resetting an AirPort Base Station or Time Capsule FAQ
Then, temporarily locate it in close proximity (same room or nearby) to the AirPort Extreme.
Open Macintosh HD > Applications > Utilities > AirPort Utility
Click the tab in the upper left hand corner of the AirPort Utility window that reads Other AirPort Base Stations (1), then click the Time Capsule
AirPort Utility will take a moment or two to analyze your network, then announce that the TC will be configured to extend your wireless network.
Enter a name for the TC (you can use the same device name that you used before if you wish) and click Next.
AirPort Utility will take a another minute or two to configure the TC and then tell you that the setup is complete. Click Done
At this point, power down the TC and move it to a location that is approximately half the distance from the AirPort Extreme and the area that needs more wireless coverage.....to give the TC a good strong signal to "extend"
Power up the TC and wait for the green light and then you are all set.

How to find out wireless access point?

Hi all!
I want to write one simple program which could detect all wireless access point're running around me. So pls somebody could tell me what I have to do now?
Thank you so much!

Dear prometheuzz !
I knew it but :) OS default can't detect AP which not
broadcast SSID. By the way why U said that Java is
not suitable for this task???Dear viethanguyen ,
Java doesnt have this functionality, cause Java is a High Level language, and what you are asking for is low level programming that is related to the underlying OS system calls and modules. So if your OS doesnt have/support this functionality, then how you expect Java to have it!. And if you are using GNU/Linux search for tools like kismet, air-snort ...etc.
Amr M. Kamel

How to setup a wrt54g router as a wireless access point to extend wifi signal from e3200

Similar Messages

Maybe you are looking for