How to setup LR 4.2 to use forward/reverse mouse buttons

I recently had to reinstall LR 4.2 due to a hard drive failure. Previously, I could cycle through my photos by using the forward or reverse buttons on the side ofmy Microsoft mouse. Now I cannot. How can I get LR to respond again? I have set the mouse to 'enable program specific settings',  but it did not help and I do not think I had to do this step in the past. Thanks.

After further inspection of the Microsoft mouse settings in the control panel, I found that each button can be programmed to a keystroke. I just made the front side button the right arrow key and the rear button the left arrow key. It works as it should now to cycle through the images in the filmstrip and the Grid view.

Similar Messages

  • How do you use forward and back button on mouse and use "zoom" in web browser.

    Ok so apparently this forum is ruled with an iron fist or something my very honest and truthful problems with these issues seem to have been instantly deleted in my last discussion?
    I'll try this once more.
    1) How do you use the forward and back button on a mouse without having to buy a product like Steer Mouse? There must be a way to do this without having to buy a program given it's such a useful feature that 99% of users need. I don't want to spend hours researching something that should already work. Any advice?
    2) How do you zoom in for web browsers like Chrome without it globally zooming in everything on the monitor (even background applications). I don't want to zoom in background applications. I want to be able to zoom in the web browser and still maintain all the features like the side bar, not just a little magnifying glass type thing.
    I'm currently zooming in with the CTRL-Middle Mouse button, but I can't find a way to use this feature so it's useful to browse the web it seems to not scale the browser correctly but rather is a global zoom. Any solution for this?

    Thanks so much!
    Like I said I am new to Apple products so it's still unclear to me which programs I do or don't need as I'm setting up and configuring all my software and devices.
    The Logitech Control Center appears to work perfectly for what I was trying to do!
    I accidently clicked "This helped me" instead of "This Solved My Question", sorry about that this was a solve!

  • How to change the search provider when using the Firefox Home Button Search feature?

    In Firefox itself I have configured duckduckgo as my default search provider.
    But when I use the Firefox Home Button Search it is always set to google and I do not see any option to change that?
    I like the Firefox Home Button Search (or whatever it's called) otherwise, but it's annoying that it does not use the default from Firefox.
    I use the Google Now Launcher.

    ''philipp [[#answer-704494|said]]''
    <blockquote>
    ...usually it will be enough to switch the default engine in firefox back and forth once to work around the issue...
    </blockquote>
    Thank you, problem resolved

  • Using the right mouse button with JTables

    Hi Folks,
    Can someone describe how to allow the right mouse button to select rows in a JTable? Or can someone tell me how to access the code which is activated when the RMB is clicked on a JTable so I can copy it.
    Thanks.

    Can you attach a screenshot?
    *http://en.wikipedia.org/wiki/Screenshot
    Use a compressed image type like PNG or JPG to save the screenshot and make sure that you do not exceed the maximum file size (1 MB).
    Make sure that you do not run Firefox in full screen mode (press F11 or Fn + F11 to toggle; Mac: command+Shift+F).<br />
    If you are in full screen mode then hover the mouse to the top to make the Navigation Toolbar and Tab bar appear.<br />
    You can click the Maximize button at the top right to leave full screen mode or right click empty space on a toolbar and use "Exit Full Screen Mode" or press F11.<br />

  • Why is it that sometimes when I use my middle mouse button to click on a link to open it in a new tab I will have it open it in an entirely new instance of Firefox instead of a new tab?

    Occasionally when I click on a link with my middle mouse button, instead of opening the page in a new tab, it will open a new instance of Firefox.
    I've looked through some of the settings and I wasn't able to find anything. It really gets to be bothersome at times because I prefer things to be in tabs instead of a new browser.

    It's not specific sites. I can middle-click on the same link 50 times and it will open it in a new tab 45 times and 5 of those times, it will randomly open it in an entirely new window. I don't know what's causing this.
    It happens so randomly that I don't know how to pin-point what it could be.

  • Using the middle mouse button to open a link in a new background tab also reloads the current page.

    When I click on a link with the middle button to open the link in a new background tab, the original page reloads and my view jumps to the top each time.
    The new tab loads fine but in order to continue reading the original page I have to scroll down to where the link I clicked on is.
    If I right-click on the link and select "Open Link in New Tab" from the context menu then the behaviour is as expected -- does not reload the original page. The flaw only happens when using the convenient mouse shortcut.
    This is annoying, for example, on long Wikipedia articles where I want to open some of the cited pages in other tabs for reading later whilst I continue to read original article. I'm constantly having to find where I was in order to continue reading.
    I've observed this behaviour on both Windows XP and Ubuntu on various computers.
    [EDIT]: Better description of problem in title.

    I've never had that happen with Firefox 4 on WinXP. I haven't updated my Netbook that runs Ubuntu to Firefox 4 yet.
    1. Try disabling the Java Console 6.0.24 and the Java Quick Starter 1.0 extensions and see if that solves your middle-click problem.
    2. Try the Firefox SafeMode. <br />
    ''A troubleshooting mode, which disables most Add-ons.''
    ''(If you're not using it, switch to the Default Theme.)''
    # You can open the Firefox 4.0 SafeMode by holding the '''Shft''' key when you use the Firefox desktop or Start menu shortcut.
    # Or use the Help menu item, click on '''Restart with Add-ons Disabled...''' while Firefox is running. <br />
    ''To exit the Firefox Safe Mode, just close Firefox and wait a few seconds before using the Firefox shortcut (without the Shft key) to open it again.''
    If it is good in the Firefox SafeMode, your problem is probably caused by an extension, and you need to figure out which one. <br />
    http://support.mozilla.com/en-US/kb/troubleshooting+extensions+and+themes

  • When using the right mouse button in Yahoo mail inbox (Firefox 8.0.1, Win 7, Yahoo Mail Plus) the Firefox navigation window (Back, Forward etc...) is on top of the Yahoo email menu (Open, Print, Reply etc...). This happens in Firefox safe mode as well.

    This also happened in Windows XP which I was using until recently.
    The Yahoo mail menu is there but the Firefox menu is on top of it. I tried Firefox safe mode with everything disabled and the problem still happened. I tried Yahoo mail in IE 9 and the right mouse button works correctly.

    Can you attach a screenshot?
    *http://en.wikipedia.org/wiki/Screenshot
    Use a compressed image type like PNG or JPG to save the screenshot and make sure that you do not exceed the maximum file size (1 MB).
    Make sure that you do not run Firefox in full screen mode (press F11 or Fn + F11 to toggle; Mac: command+Shift+F).<br />
    If you are in full screen mode then hover the mouse to the top to make the Navigation Toolbar and Tab bar appear.<br />
    You can click the Maximize button at the top right to leave full screen mode or right click empty space on a toolbar and use "Exit Full Screen Mode" or press F11.<br />

  • I can not open the bookmarks tab or use the right mouse button in firefox

    ''locking this thread as duplicate, please continue at [https://support.mozilla.org/en-US/questions/1053467 /questions/1053467]''
    I recently downloaded firefox to my new laptop. I can not open the bookmarks tab or use any of the right mouse button options.

    Do a clean reinstall and delete the Firefox program folder before (re)installing a fresh copy of the current Firefox release.
    *Download the full Firefox installer and save the file to the desktop<br>https://www.mozilla.org/en-US/firefox/all/
    If possible uninstall your current Firefox version to cleanup the Windows registry and settings in security software.
    *Do NOT remove "personal data" when you uninstall your current Firefox version, because this will remove all profile folders and you lose personal data like bookmarks and passwords including data in profiles created by other Firefox versions.
    Remove the Firefox program folder before installing that newly downloaded copy of the Firefox installer.
    *(32 bit Windows) "C:\Program Files\Mozilla Firefox\"
    *(64 bit Windows) "C:\Program Files (x86)\Mozilla Firefox\"
    *It is important to delete the Firefox program folder to remove all the files and make sure that there are no problems with files that were leftover after uninstalling.
    *http://kb.mozillazine.org/Uninstalling_Firefox
    Your bookmarks and other personal data are stored in the Firefox profile folder and won't be affected by an uninstall and (re)install, but make sure NOT to remove personal data when you uninstall Firefox as that will remove all Firefox profile folders and you lose your personal data.
    If you keep having problems then also create a new profile.
    *http://kb.mozillazine.org/Profile_folder_-_Firefox
    *http://kb.mozillazine.org/Profile_backup
    *http://kb.mozillazine.org/Standard_diagnostic_-_Firefox#Clean_reinstall

  • How to setup VoIP/Ipsec on SRP527W using web gateway

    I'm trying to setup a IPSec tunnel and VoIP for the Cisco SRP527W-K9-G5 but all I find are examples using the cisco ios which this model doesn't support. I'm using the web interface to the router and there is no examples to follow.
    There is no manual, the online help is not very helpful either.
    I've tried going to the "Voice" tab but could not figure out where to put the SIP or the phone number.
    And is there any examples, manual or anything that shows how to create a ipsec tunnel using the srp527w's web interface?

    Hey,
    Thanks a ton for posting this out here. I am sure it will be helpful for people trying this out.
    Regards,
    Prapanch

  • How to setup a T3 connection for use in weblogic

    When I try to make a t3 connection using the existing http port that I have, I get the following exception
    Error message :javax.naming.CommunicationException [Root exception is java.net.ConnectException: t3://srvr:7092: Bootstrap unable to get a t3 connection to srvr/11.16.8.10]
    How do I setup a T3 connection
    Thanks

    Hi,
    Is the above phenomenon right? How can I know the tip connection
    is established? Shouldn't it display 'Login' after it display 'connected'?
    To display login at the tip connection you can do one of the following.
    1. remove the keyboard and reboot with a tip connection.
    2. at ok> set the output-device input-device as ttya
    setenv output-device ttya
    setenv input-device ttya
    reset.
    Note: the same can be done from a teminal/console using eeprom command.(man eeprom)
    To get back the display and keyboard access during bootup
    you will have to reset input/output device values back to the default values
    setenv output-device display
    setenv input-device keyboard
    3. Add the following to the /etc/inittab file
    +++++++++++++++++++++++++++++++++++++++++
    c5:234:respawn:/usr/lib/saf/ttymon -g -h -p "`uname -n` ttya login: " -T sun -d /dev/ttya -l console -m ldterm,ttcompat
    +++++++++++++++++++++++++++++++++++++++++
    Please save the original copy ..
    "init q " (to make the inittab file to be read again)
    4. using admintool -->Browse->Serial ports->Select ttya->Service Enable->Ok->Exit.
    For KSLD setting the output-device and input-device is the best option.
    KSLD is EOL (End of Life) so product support will not be available.
    HTH
    -Dhruva

  • How to setup a live USB stick using the latest archlinux 201405

    Hello, long time reader, first time poster.  I recently purchased a new computer, and I would like to setup arch linux as host OS, so I can see if I could build a LFS system from the Arch Linux live USB drive.  When I run the following command "dd if=/arch.iso of=/dev/myDisk" it successfully creates a USB drive that is bootable on the new computer (it's using EFI) and the system boots into a shell prompt.  However, when running the above command, my host OS (OS X) on my other computer doesn't recognize the drive, so I can add files or do anything with the remaining 15.5GB of storage on the drive.
    I came across this document, => https://wiki.archlinux.org/index.php/US … tion_Media which I must say is very well documented (kudos).  So I mounted the Arch_Linux_2014.05 ISO and copied the files to freshly formatted (FAT 32) USB drive, and inserted into the new computer, and it see's the EFI boot option, when I hold down the "option" key when the computer boots up (that's good).  However, it doesn't bootstrap the Linux kernel or the Arch Linux base system for that matter.
    I came across this forum post, => https://bbs.archlinux.org/viewtopic.php?id=135046 where a member was discussing editing some files to get his USB drive to boot.  I wasn't sure if this forum thread was still relative as it a couple years old.
    Finally, the reason I prefer the mounting of the ISO, and copying the files is so that 1) my host OS on my old computer (OS X) can read the USB drive. 2) I can add files to the USB drive without having it locked down.
    Thanks for reading, and any help would be greatly appreciated.

    After fooling around with the grub.cfg I finally got it to boot.
    The menu entries I added to the grub.cfg look like the following,
    menuentry "[loopback]arch_201405.iso" {
    set isofile="arch.iso"
    loopback loop (hd0,1)/$isofile
    linux (loop)/arch/boot/x86_64/vmlinuz archisolabel=ARCH_201405 img_dev=/dev/sda1 img_loop=$isofile earlymodules=loop
    initrd (loop)/arch/boot/x86_64/archiso.img
    menuentry "[loopback]arch_2014.04.01-dual.iso" {
    set isofile="archlinux-2014.04.01-dual.iso"
    loopback loop (hd0,1)/$isofile
    linux (loop)/arch/boot/x86_64/vmlinuz archisolabel=ARCH_201404 img_dev=/dev/sdc1 img_loop=$isofile earlymodules=loop
    initrd (loop)/arch/boot/x86_64/archiso.img
    I added the archlinux-2014.04.01-dual.iso file to the USB flash drive because apparently there is a bug with the 201405 version of archlinux using fat32 and booting into a live environment, https://bugs.archlinux.org/task/40217

  • HT4112 how does one navigate with out the use of a mouse? do we still need to use finger to move to different things?

    how does one navigate the keyboard without a mouse. Do we still use finger to move from place to place?

    Yes you still need to use your finger to do all of the things that you need to use it for even if you use a wireless keyboard. You are merely adding a larger more robust keyboard to the device. You are not replacing the touch gestures features with the use of an external keyboard.

  • How can I change the active Midlet using the '*' cell phone button

    Hello
    I've got a problem trying to do that in J2ME MIDP:
    'I have different class extending Midlet that I want to display one after the other. The change may be done when I click the '*' button of my cell phone'
    For the moment I've created a main class that extend Canvas and which contain a vector of objects extending Midlet.
    I'm able to change the objet which I want to display, but not to display it....
    Is it possible to do that?
    Do you have any idea of how to deal with that?
    Thanks a lot...

    Hello
    Thx for your answer .. but I shouldn't have explain correctly my problem because I don't think this answer it .. sorry
    I need an interaction between a Midlet class and a Canvas class.
    In fact I have several forms, and I need to allow my Canvas class to change the form displayed when a button is pressed.
    But If I have a form in a Midlet , I can display it but can't catch the click on a button.
    And if my Canvas is displayed I don't know how to display the form I want to.
    So is it possible to do that... and if so, how?
    Thank you very much...
    Al161084
    Message was edited by:
    al161084.1

  • How to setup a sound bar on LED TV 42SL417U

    So I've been trying to figure out how to setup a sound bar that uses AUX Left and Right cables onto my LED TV 42SL417U. I've been trying to connect the cables into every possible port on the TV and nothing works. What do I do???

    Hi -
    What make/model of sound bar are you trying to connect?
    The only "outputs" for sound to an external device from this TV are the Optical and HDMI connections. Page 18 and 19 of the Owners Manual talk about connecting to an external audio source.
    Hope this helps.

  • How to setup Tibco EMS as the JMS Provider

    Hi,
    Are there anyone know how to setup the app. server to use Tibco EMS (installed in a remote machine) as the JMS service? May I have the setup example?
    I put the host name and port of the EMS server on the Configuration JMS page. I ping the setting but I got the following:
    An error has occurred.
    Operation 'JMSPing' failed in 'resources' Config Mbean. Target exception message: [C4003]: Error occurred on connection creation [10.0.0.104:7222]. - cause: java.lang.NumberFormatException: For input string: "&#65533;"Any idea?
    Thanks a lot for your help in advance.
    Simon

    Hi,
    Are there anyone know how to setup the app. server to
    use Tibco EMS (installed in a remote machine) as the
    JMS service? May I have the setup example?The default jms commands [like jms-ping] are designed to be used against Sun Java System Message Queue that is bundled with the appserver. For integrating third party JMS providers like Tibco EMS, could you try out Generic RA for JMS [http://genericjmsra.dev.java.net]
    Detailed instructions on getting Sun Java System Application Server to work with Tibco EMS using Generic RA for JMS is available off
    https://genericjmsra.dev.java.net/docs/tibco-genericjmsra-integration-sample-doc/Integrating_Sun_Java_System_Application_Server_with_Tibco_JMS_using_the_Generic_Resource_Adapter_for_JMS.html
    Thanks
    --Siva.                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                               

Maybe you are looking for