How to setup netgear N150 wireless Router to apple tv ?

im an infant that has finally given in to technology, that could use a little help
setting up NETGEAR N150 wireless router to my Apple TV ?

See my other reply. Avoid double posts if you can.

Similar Messages

I need to know how to connect to internet using the netgear n150 wireless router

I recently signed up with comcast internet. They supplied a NETGEAR N150 wireless router. After following instructions that came with router, I still cannot use the router to connect to the internet. The computer has to be connected directly to the modem for internet access. HELP!!!!

Here are some of the recommended setting from Apple. Maybe that will help.
http://support.apple.com/kb/HT4199
Regards,
Captfred

HT1731 Help installing Airport Express with Netgear N150 wireless router? I hav

Hi,
I just purchased the newer Airport Express (new) and am having issues using it in client mode with my Netgear N150 wireless router. All I want to use it for is streaming itunes from my aluminum macbook to my home stereo system, wirelessly.
I have followed the instructions that came with the device. No luck. I have followed the instructions that describe plugging it into an ethernet cable here:
http://support.apple.com/kb/HT1731
With the apple instructions linked above it would connect fine to my existing wireless network, using airport utility, with 'excellent' connection, but when I tried to switch in itunes to my device from my computer i get the pinning wheel and an 'unknown error' occurs.
I have setup a new wireless account and password on my router as desribed at this page, but do get confused when it tells me to use the hex key and $. Haven't worked that out yet. Any advice would be appreciated if this would help.
http://hints.macworld.com/article.php?story=20041017233832771
At best, after hard resetting the device several times, and following the instructions above at macworld, it now finds the device but only plays one blip second of a song, flashing amber from solid green, sometimes playing a second blip of a song, then pausing the song and switching to a flashing amber. By restarting my computer or opening AirPort utiliy I am able to find it again, but it either only plays one second of a song and drops again or turns green and is not able to be found at all by itunes (the button doesn't show up in the menu).
This is the second airport I have tried in 2 years. I purchased a used one and had nearly the exact same issues with a linksys router. Then it would play an album but reset if a song was paused.I had to hard reset it nearly every time i wanted to stream from itunes to my stereo. I assumed it was broken and sent it back. Figured I 'd give it a new go around with a new unit since i just moved into a new house and am now shocked at how difficult it is to set up. I have never had this many issues with an apple device.
My questions:
1) How can I set this up with my existing router? What am I doing wrong?! Why is it so difficult?
2) If not possible, what routers are compatible? I would gladly get a new router in order to stream music to my stereo from ITunes.
thank you for any assistance. i am pulling my hair out.

Try temporarily disabling the Windows 7 firewall, and then, try accessing the AirPort with the AirPort Utility again.

How to install netgear wgr614v6 wireless router

im having so much trouble with this. its not doing nething it sud be. absolutely no help off netgear and no instillation cd. can anyone help please!

Try the netgear support forums. This is a Linksys forum. If you have a problem with a Linksys router you are at the right place. If you have a problem with a Netgear router you should go to a Netgear forum.

Slow access in E900 N150 wireless router

Hi,
I bought a Ciso Linksys E900 N150 wireless router yesterday. I configured router succesfully with the help of Setup CD.
On my wired connection I am getting 10 Mbps speed. Things are bad when connected via router. A wired-router connection or wireless connection via router is giving me hardly 100 kbps.
I tried setting my security to WAP2 Personal , WMM is disabled in Q0S. However my guess failed.
I am struggling with router at this moment. I am clue less on what may be wrong.
Please advice me.
Regards,
Sagar

Hi ,
I tried MTU increment by 10 from 1200 to 1492. This didnt help me.
Please help me.
zee29 wrote:
Better check that MTU size. It would be best if you select the correct MTU size. Click the link below on how to determine the correct MTU size. Also, uncheck IPv6 in your computer adapter properties and see if that would help.
Title: Determining and setting up the correct MTU size
Article ID: 386
http://kb.linksys.com/Linksys/ukp.aspx?vw=1&docid=fbf8e8564632422eaa8ea80bf9dcba64_386.xml&pid=80&re...
zee29 wrote:
Better check that MTU size. It would be best if you select the correct MTU size. Click the link below on how to determine the correct MTU size. Also, uncheck IPv6 in your computer adapter properties and see if that would help.
Title: Determining and setting up the correct MTU size
Article ID: 386
http://kb.linksys.com/Linksys/ukp.aspx?vw=1&docid=fbf8e8564632422eaa8ea80bf9dcba64_386.xml&pid=80&re...
Regards,
Sagar

Connecting Westell 6100G to Netgear n300 Wireless Router

I've just purchased a netgear n300 wireless router. My question is would I defintely need to set the Westell 6100G modem to bridge mode? After I do that I simply connect the wireless router to the modem and then the router to the computer via one of the ports? After that is done would I need to do anything else? Would I be asked for my verizon login and password in order to get connected?
Solved!
Go to Solution.

It's recommended to bridge your modem as the modem itself does have an integrated router, even though it only has one Network port to connect up with. You have to split it up using a switch if you wish to really use it as a wired router. The reason why you bridge is so that your router holds your Public IP address rather than the modem. This avoids a condition known as "Double NAT" which game consoles dislike, VPNs tend to be iffy with, and Port Forwarding becomes a pain to do as you have to do it twice.
Yes, Bridge the modem. As far as the Netgear is concerned, if your modem reports that it is using PPPoE, the Username and Password you will need to use will be the master login you use for your DSL account. In the Netgear, it will auto detect that you use PPPoE in most circumstances however, it won't automatically pull your username and password. In some cases it may just connect right up if Verizon still does OpenPPPoE. Otherwise, if you're using a Setup program that came with the router it should ask you for your username or password to connect up. If not, Netgear has changed their firmware around in recent years, but in most cases it is under the Basic Setup or "Internet" section of your router for adding in a PPPoE username and password. The best place to look for this would be the user guide for your router. It should detail how to set up your connection based on what you're using.
========
The first to bring me 1Gbps Fiber for $30/m wins!

Can I Show Time Connected When Using Netgear DG834 Wireless Router ?

When I had an old SpeedTouch USB Modem I could see the time I had been connected to the internet from a readout in the menu along the top of the monitor.
Is there a way of displaying or ascertaining this information using the Netgear DG834 wireless router?
I have discovered that by opening the Router Satus and clicking on "Connected Status" I can get a window displaying this info - but is there a quicker "automatic" way of doing it?
Ian.

Hi Ian,
Interesting one…
When you connect via a USB modem the computer is 'doing' the connecting using the modem so the computer has the 'time connected' status available locally. In the case of a router it is connected to the internet irrespective of the computer's status; on, off, sleep, or even, connected to the router. The only way you're going to get the info is from the router itself and, unless it has a setting whereby it will automatically 'inform' the computer of its connected time, I think you're going to have to carry on as you are.
I don't know that particular Netgear but used to have a different one until a thunderstorm fried it. I don't remember it having such a setting. My current Belkin certainly hasn't.
I'm quite interested to know why you want this info. Are you on some kind of PAYG tariff?
Adrian

How do I make my wireless router the "preferred" one?

How do I make my wireless router the "preferred network"? I have to manually re-select it each time I boot up or when it comes out of standby. This has only started to occur now that I have a new wireless router. I want it to automatcially select my router.

Have you restarted your computer? Repaired permissions and restarted your computer?
Which os are you using?

Don't have an aircard- do have netgear n wireless router -unit is an imac g5-power mac 8,1-cpu g5 3.0-proc 1.8-mem 1.5-os 10.4.11 don't have which one should I get for imac g5 -power mac 8,1-cpu g5 3.0- proc 1.8-mem 1.5-os 10.4.11

don't have an airport card- do have netgear n wireless router -unit is an imac g5-power mac 8,1-cpu g5 3.0-proc 1.8-mem 1.5-os 10.4.11 what airport card should I get ?

Look HERE to find the appropriate airport card - you can use an Airport Extreme card.
And here to buy one.

HT4199 I have a Netgear R6300 wireless router and a Yamaha RX-3020 A/V receiver. An app is available to run on an Ipad. I have to reboot every morning to get it all working. Can I just plug cat6 between them, when I do nothing works, please help

Should I use a network switch and plug my Yamaha A/V receiver and Yamaha DVD into it, then into the wireless router? Then the net into the routers net port???

HT4199 I have a Netgear R6300 wireless router and a Yamaha RX-3020 A/V receiver. An app is available to run on an Ipad. I have to reboot every morning to get it all working. Can I just plug cat6 between them, when I do nothing works, please help

Does anyone know how to set up the wireless router when y...

does anyone know how to set up the wireless router when you have a Vonage modem and a cable modem? HELP!

You mean u got 2 modems ?
C | EH
linksyshelp.blogspot.com

Something happened to my Netgear wgu624 wireless router

I have a Netgear WGU624 wireless router that seems to have stopped working today. I had my cable modem connected to it and it was creating a wireless network for my three computers.
I had to switch to plugging the ethernet cable directly from my cable modem into my macpro so I could get online.
I'm not sure what the problem is with the router but I don't seem to remember the a & g lights blinking before like they are now. I tried plugging the an ethernet cable directly from my router into the second ethernet port on my macpro (with the cable modem plugged into port 1) to see if I could access the router by going to 192.168.1.1. No luck, the browser says "failed to open page".
Is there some way to check to see if the router is bad? We did have a storm today. Everything else is fine though...
Any thoughts would be appreciated.

Good choice on the Airport base Station.
Especially, since that netgear was so hard to manage.
You may have gotten a spike during your storm, but you still didn't give us enough information to be useful
You should have seen a router address in network prefs, yes.
Aaah, naples. My grandparents bought a little condo on Gulf Shore Blvd, across from Edgewater Hotel...in 1968. (2br, 2ba, facing hurricane harbor, $23K) You don't want to know what some of these condos are selling for now.
We've been regulars on the beach for the past 40 yrs. Hard to watch some of the older places scraped, and those $8mm McMansions popping up, but what's more phenomenal are the changes up and down the trail. I mean between naples and Bonita, whoa! And the growth out towards Marco and out ON marco.
Nice

How setup a WRT54G2 Wireless Router to connect to a SmartPhone to Retrieve E-Mail

I have a new WRT54G2 Wireless Router and I can Surf the Web on my Smartphone via the Router but I am unable to retieve my E-Mail like I used to do with my old Wireless Router.
Anyone know what setting I need to change on the WRT54G2 Wireless Router?

Hi Richard,
Welcome to the community forum!
Did you check the mail setup in your smartphone to see if anything changed? Check if the incoming and outgoing mail servers are correct.
A software update might have reset the settings.
If all looks good in the smartphone mail setup, do you recall if you had to open ports in the old router to make email work?

Need help setting up Airport Express A1084 in Windows 7 via Netgear WNDR4500 wireless router

Hello All. I bought a used Airport Express A1084 off the net. Never had one before. My intention is to remotely control (via my iPhone using Apples Remote app or possibly XBMC) a "pc with music" and stream thru the AE connected to a boombox. I want to be able to take AE and boombox to the front yard, back yard, garage, or wherever my Netgear WNDR4500 will reach.
So far I have hit the reset on the AE and while holding, plugged it in to power (still holding) until the green light blinked. I let it go. Waited for it to complete booting (slow blinking yellow/amber light). The AE did not show up in Airport Utility ver 5.6.1. I uninstalled that version and installed older Airport Utility ver 5.4.2. Same results. I power cycled the router, turned off the Norton 365 firewall, and still get nothing. At one point though, I walked away for a while (an hour or so), came back and saw the AE listed in the left window pane of Airport Utility. I thought maybe I just didn't wait long enough so I clicked Manual Setup and it started to read the AE but Errored 10057. I tried again and got same error. I refreshed and the AE was gone.
Can someone tell me how to correct this so I can confirm I didn't buy a "brick"?
Thanks in advance,
Tom

Just so you are aware, the A1084 AirPort Express is a 802.11b/g wireless router that can only operate on the 2.4 GHz band. Regardless, it can be configured to join the wireless network provided by the Netgear as long as that network is configured to be backwards compatible with 802.11g clients. However, in the long run for performance, you do NOT want any non-"n" wireless clients connecting to your Netgear's network.
The 5.6.1 version of the AirPort Utility for Windows does not support the non-"n" version of the AirPort base stations. You would need to use an earlier version that will still run on Windows 7.
One thing to try would be to temporarily connect the Express directly to your PC using an Ethernet cable, and then, try accessing it with the AirPort Utility. If you are still unable to do so, you may have gotten yourself a defective unit.

How can I mange a wireless router behind a wired router?

I've got cascading routers configured as recommended in Linksys Answer ID #3733. Wired router BEFSR41 is closest to Internet and wireless WRT54G is behind it. I want to mange the wireless router remotely. Should routers be on the SAME IP segment or different IP segments to accomplish this? What special settings are needed?  What is structure of browser address to access administrator logon of second router?

It sounds like you want to be able to remotely admininister the entire network, via the Internet --- sorry, I don't know how to do that part of your problem.
However, the network setup itself sounds fairly simple:
It sounds like you want a network like this:
Modem ---- BEFSR41 ----- WRT54G   ))))) wireless computers
                          |                            |
             wired computers        optionally more wired computers
The best way to set this up is to leave all your devices on a single subnet (for example, 192.168.1.x ) and convert the WRT54G to a WAP (wireless access point).
BEFORE connecting the two routers, set the WRT54G to the following:
Local IP address:   192.168.1.2   (this assumes BEFSR41 is still set to 192.168.1.1, with default DHCP server range, and that you are not using 192.168.1.2 elsewhere in your network)
SSID: use a unique name (Note: do not use "linksys" )
SSID broadcast: enabled
encryption method: optional
encryption key: optional
If you want your wireless computers to only be able to access the Internet, and not each other, and not any printers or other network devices, then set "AP isolation" to "enabled" for this increased security.
DHCP server: disabled
Next, power down entire system.   Then wire any LAN port from BEFSR41 to any LAN port on WRT54G. Do not connect anything to Internet port on WRT54G. Note that all remaining wired LAN ports on both routers will be functionally identical, so you can plug your wired devices into any of them. If you need more wired ports, add an SD208 or SD216 switch to either, or both, routers.
BEFSR41 will control all the usual router settings:  DHCP server, port forwarding, remote access, etc.   WRT54G will only control its own wireless settings.
I'm sure someone else will be able to help you with remote management of the network.

How to setup netgear N150 wireless Router to apple tv ?

Similar Messages

Maybe you are looking for