How to setup Private VLAN in Small business switch SF200-24

Dear All,
According release notes 1.4 , private vlan is supported. I've upgraded my SF200-24 with firmware 1.4.0.88 and boot 1.3.5.06. The system information show firmware version 1.4.0.88 and boot version 1.3.5.06 after reboot. I can't find private vlan setup command on GUI. Please help me to setup private vlan. Thanks.

Hi,
Unfortunately PVLAN is not supported on 200 series. However you might be able to overcome this using general port concept.
for example:
isolated port - general 10P (PVID), 30U, drop tagged traffic
community - 20UP, 30U, drop tagged traffic
promiscuous - 30UP, 10U, 20U
Note: primary vlan 30
does it address your requirements?
Aleksandra

Similar Messages

How to setup private network in oracle rac

Hi all,
Iam trying to setup oracle 2-NODE RAC ,
now i stuck in setup private network..
how to setup private network, what i have to do for that.
please help us provide step by step process

The loop is nothing but a network cable connecting two nodes on same port with a private IP address (something like 10.0.01 and 10.0.0.2) which is not accessible by any other machine in the network (except 2 nodes obviously ).
Note that cross over cables are not supported for the Cluster Interconnect. And cross over cables limit the cluster to only 2 nodes, which may not be enough for many RAC deployments.
Cheers,
Brian

SG200 Small business switch - vlan issue

I have the wonderous task of remotely configuring a few SG200 small business switches.
I need to create a vlan and move a few ports into that vlan, doesn't sound too difficult.
I have created the vlans but when I go to add the ports into the vlan the only option I seem to have is General?
If I specify access I can't say what vlan the port should be in?
What am I doing wrong?
All ports are currently in VLAN 1 and are in mode trunk
I have created 2 new vlans and just want to put 4 ports in VLAN 2 and 4 ports in VLAN 4
Can anyone impart any wisdom?
Thanks
Roger

Hi Roger,
Did you try this guide?
http://sbkb.cisco.com/CiscoSB/Loginr.aspx?login=1&pid=2&app=search&vw=1&articleid=80
Are you configuring it from GUI or CLI ?
Regards
Mariusz

Best small business switch for 100-300 user UC deployments

Hello,
The SMART Designs state that both the ESW500 and 300-series switches should not be used for deployments of over 100 IP phones.
But now that both the UC560 can go up to 138 (128 IP phones) and the BE3000 can go up to 300 users is this design restriction still valid or is the Catalyst 2960 and above the only options?
The QPT is still showing both the 300- and ESW500 switches as options for all versions of the UC560, and the 300- and 2960 switches are shown as valid options in the LAN for the BE3000.
Thanks.

Hi All,
I would agree with the folks at smartdesign, but for a very differerent reason as suggested by kmacpherson..
But think about the Business Edition 3000 (BE3000) and how it's supported. BE3000 is supported by the traditional Cisco TAC that also supports the catalyst 2960S etc....
The 300 series switch is supported by the wonder folk at the Small Business Support Center (SBSC) .
300 series of switches are generations ahead of the ESW switch in terms of switch silicon/features/GUI/supported CLI/IPv6 support etc..it is a tremendous switch series..
From my perspective, even though there is now a lot of dialogue between TAC and SBSC these days, it sorta makes a lot of sense in my mind to position Catalyst switches in conjunction with BE3000 for your end users, and 300 series small business switches as a lower cost alternative.
This will mean there will be pretty seamless TAC support for a BE3000, catalyst, ISRG2 solution.
regards Dave

LMS 3.2 and Cisco Small Business Switches

Hi there,
I'm currently using LMS 3.2 to monitor my network. We've recently purchsed a few of the Cisco Small Business Switches, the SF 300-24 model to be exact. They're considered 'managed switches' (tho thier CLI is terrible) and I would like to monitor them in CWLMS. My problem is that once I add it to CS, it doesn't resolve to anything, just sits there as a blue box with a question mark. I'm assuming this means that these devices are not (currently) supported by LMS 3.2 - do you know if that will change, or how I can go about managing this device with LMS 3.2?
Thanks

Unfortunately that series of products is not supported in any version of LMS (or even Cisco Network Assistant - CNA).
Cisco provides the FindIt utility to manage them:
http://www.cisco.com/en/US/products/ps10660/tsd_products_support_series_home.html
Hope this helps.

Issues with Small Business Switch config

Hi, I know that if I read the documentation I will come to the answers but I would really like some input from someone with more knowledge than me. I have an issue with Cisco SF300 , one of the Small Business Switches. I have a single interface on my router and I need to separate my internal networks , I thought that one way would be to use VLANs. On my two internal networks one network only has unmanaged D-Link switches, the other has the Cisco SF300 so I did as follows.
On the Cisco Switch, all ports default to Trunk ports. I have changed FE1-FE24 and GE1-2 to access ports.
Created two VLANS and placed FE1-FE24 in VLAN10 (also my management VLAN) , GE3 is a trunk Port for VLAN20 untagged, VLAN 20 uplinks to my DiLink Switches. This way traffic from my unmanaged switches comes in on a trunk port untagged on VLAN20.
GE4 is a trunk port and I have assigned VLAN1 untagged, VLAN10 tagged and VLAN20 tagged. VLAN 10 and VLAN 20 then forward to my Router.
The plan was to connect GE4 to my router however I had two things happen I can not explain.
Firstly as soon as I connected my D-Link to GE3 the LAN on VLAN20 went down, I could not ping Servers from PCs etc, all devices are connected to the unmanaged D-Links. Secondly the VLAN Assigment changed on GE3 and GE4 , VLANs 10 and 20 disappeared and only the default VLAN was assigned, also under VLAN Settings my VLAN interface state for VLAN20 shows Disabled. Also one of my access ports FE12 keeps changing VLAN.
Can anyone offer any suggestions as to what might have crashed the LAN and why my VLANs change. I did write my running config to the start up config by the way.
I added two screen shots.
I would seriously appreciate some help.
Thanks
Bob

Hi Garrett, thanks for your reply to my post, I hope you are well. I called Cisco support, they told me that they could not understand why this was happening and suggested a firmware upgrade, usually something I should have considered right from the beginning. This solved the issue for me.
Thanks
Bob

Help blocking certain website and IP on a SG 300-20 Small Business Switch

Hi,
I like to block certain IP and website on the SG 300-20.
Being new to Cisco Small Business switch I she tried with no positive result. Could someone give me some steps or maybe direct me where I can find a step by step resource.
Thank you

Hello,
Thank you for contacting us for support with your device.
Unfortunately what you are trying to do is not possible with any Small Business switch.
It is true that this switch can be used in layer 3 and it will be able to route your traffic on the inside of the network, but it will not be able to route your traffic to the Internet as it doesn't do any NATting.
If you need to block any websites you will need to configure it on your router or firewall.
Just to be completely clear, this switch won't be able to block any websites.
I hope this was helpful

Small Business switches and POODLE

Has Cisco done any research into small business switches being vulnerable to POODLE? I know they're working hard on the enterprise side, but I'm not finding any information on the small business side.

Hi,
All Cisco product will be checked and results are posted on the same page as for enterprise:
http://tools.cisco.com/security/center/content/CiscoSecurityAdvisory/cisco-sa-20141015-poodle
Regards,
Aleksandra

How many licenses come with the small business creative cloud package?

Right now, we are using both licenses for our current CC subscription. I need just one more, but Adobe would require me to get a whole separate subscription for a total of 4 licenses and double the price. I noticed that the small business plan is $70 per month and I'm just wondering how many licenses it is equipped with. Thanks

Hi,
The plan that you are referring to at $70 per month is for 1 license within the Creative Cloud for teams.
Creative Cloud pricing and membership plans | Adobe Creative Cloud
Regards,
Sheena

WRV210 How to setup 5 VLAN?

Hi,
I have a WRV210 router and the manual says it can have 5 VLAN. I can also see the SSID or Ethernet Port can be assigned to a particular VLAN via the Web Admin page.
However, I don't know how to setup the extra 4 VLAN from the Web Admin page.
Currently, only one LAN I can setup is the default LAN (192.168.1.1) by default.
Thanks for anyone who can show me how to add more VLAN to this router.
Best regards,
Marcos

davcbr wrote:
Oh yeh; then throw out the other four routers.
Actually he can use the routers as AP's...you just need to assign them a specific IP then cascade them so they would act like switches...
Router A connects to the Internet and is set to DHCP ON (LAN IP 192.168.1.1)
Router B DHCP OFF (LAN IP 192.168.1.2)
Router C DHCP OFF (LAN IP 192.168.1.3)
Router D DHCP OFF (LAN IP 192.168.1.4)
Router E DHCP OFF (LAN IP 192.168.1.5)
You must connect from router A's regular port to a regular port also on the other routers....you can also connect the other routers (345) on the regular ports of the
first routers...just as long as you have them connected on port 1 2 3 or 4 it will act like a switch...
"The war between heaven and hell depends on the choices we make, and those choices require sacrifice. That's the test"

How to use MfE with Yahoo Small Business e-mail ac...

Hi,
I am using N97, and trying to access MfE with my company's e-mail id. We have taken e-mail id from Yahoo Small Business.
My question is
1. Is it possible to access Yahoo Small Business's e-mail on my N97 using MfE (I am using it with normal Mailbox option in phone).
2. If we can use what is the server name which I need to use for this application (It is not accepting pop.bizmail.yahoo.com).
Please help me out.
Regards
Akshara
N97 Black India
Attending Nokia Discussion has become new hobby, Thanks to Nokia... for having so many bugs

Maybe this can help you out.
http://help.yahoo.com/l/us/yahoo/smallbusiness/bizmail/pop/pop-33.html
‡Thank you for hitting the Blue/Green Star button‡
N8-00 RM 596 V:111.030.0609; E71-1(05) RM 346 V: 500.21.009

Problems setting up public/private vlans on sg300-52 switches

A real beginner here with a problem on how to setup 3 SG300-52 (in L2 mode) as per this diagram:
Port 1 on all switches should be able to talk to each other and access the blob at the right.
The ports 25 on the other hand should only be able to talk among themselves in their own
private vlan. They are to carry sensitive traffic.
So I created 3 vlans, vlan 78 for ports gi1, gi51 and vlan 10 for port25,49,50 and a dummy vlan: 666
with the intent of segratating vlan 10 from vlan 78.
My attempts so far have failed.
ports gi49-50 are configured as trunk ports and gi1,gi51 as access ports as the following
cli output (excerpts of the startup config):
vlan database
vlan 10,78,666
exit
interface vlan 1
ip address 172.16.10.11 255.255.255.0
no ip address dhcp
interface gigabitethernet1
switchport mode access
switchport access vlan 78
interface gigabitethernet25
switchport mode access
switchport access vlan 10
interface gigabitethernet49
switchport trunk allowed vlan add 10,78
switchport trunk native vlan 666
switchport default-vlan tagged
interface gigabitethernet50
switchport trunk allowed vlan add 10,78
switchport trunk native vlan 666
switchport default-vlan tagged
interface gigabitethernet51
switchport mode access
switchport access vlan 78
Ports gi1 can talk to each other and access the blob but ports 25 refuse to talk to each other. But as soon as I remove
the access links to the blob they can! Obviously, at that point port gi1 lose access.
Is such a topology feasable or even advisable?
Thanks,
jf

Hi Jean,
Here's a pretty picture
Now I will explain.
The layer 3 switch is going to service as your core switch.
Vlan 78 looks like your BLOB connection.
Vlan 10 and 666 look like they don't belong on the BLOB.
So how to configure this-
You will want to configure the switch that connects directly to the BLOB as the layer 3 switch depicted in my diagram.
Layer 3 switch, follow this document
https://supportforums.cisco.com/docs/DOC-27038
Bear with me, I am making up random numbers since I don't know what you want or will use.
So VLAN 78 looks like the BLOB and 10 and 666 are staying out of the BLOB.
config t
vlan database
vlan 10, 78, 666
int vlan 1
ip address 192.168.1.254 /24
int vlan 10
ip address 192.168.2.254 /24
int vlan 78
ip address 192.168.3.254 /24
int vlan 666
ip address 192.168.4.254 /24
Configure the port you want to go to the BLOB, I am assuming vlan 78.
config t
int gi01
switchport mode access
switchport access vlan 78 (that 3750, what is the native vlan of the port it is connecting to??)
Next, configure the downlink port to connect the layer 2 switch
config t
int gi0/2
switchport mode trunk
switchport trunk allowed vlan add 10, 78, 666 (this will make the port native vlan 1 untagged, rest ports tagged)
On the downstream switch you need to configure an uplink and downlink with the respective vlans. It will remain layer 2 mode.
config t
vlan database
vlan 10, 78, 666
int gi0/1
switchport mode trunk
switchport trunk allowed vlan add 10, 78, 666
int gi0/2
switchport mode trunk
switchport trunk allowed vlan add 10, 78, 666
Same thing for the last switch, it will remain layer 2 mode
config t
vlan database
vlan 10, 78, 666
int gi0/1
switchport mode trunk
switchport trunk allowed vlan add 10, 78, 666
int gi0/2
switchport mode trunk
switchport trunk allowed vlan add 10, 78, 666
Let me know if this works out or if it is not logical for you.
-Tom
Please mark answered for helpful posts

Private VLAN Promiscuous Trunk Port - Switches which support this function

Can anyone confirm if the "Private VLAN Promiscuous Trunk Port" feature is supported in any lower end switches such as Nexus 5548/5672 or 4500X? According to the feature navigator support seems to be restricted to the Catalyst 4500 range (excluding the 4500X) as shown below. If the feature is going to be supported in the Cat 3850 this would be good to know, thanks

4500x Yes
http://www.cisco.com/c/en/us/td/docs/switches/lan/catalyst4500/release/note/OL_26674-01.html
Nexus 5k Yes
http://www.cisco.com/c/en/us/td/docs/switches/datacenter/nexus5000/sw/layer2/521_n1_3/b_5k_Layer2_Config_521N13/b_5k_Layer2_Config_521N13_chapter_0100.html
3850s
They dont support pvs at all yet
http://www.cisco.com/c/en/us/td/docs/switches/lan/catalyst3850/software/release/3se/vlan/configuration_guide/b_vlan_3se_3850_cg/b_vlan_3se_3850_cg_chapter_0100.html
Restrictions for VLANs
The following are restrictions for VLANs:
The switch supports per-VLAN spanning-tree plus (PVST+) or rapid PVST+ with a maximum of 128 spanning-tree instances. One spanning-tree instance is allowed per VLAN.
The switch supports IEEE 802.1Q trunking methods for sending VLAN traffic over Ethernet ports.
Configuring an interface VLAN router's MAC address is not supported. The interface VLAN already has an MAC address assigned by default.
Private VLANs are not supported on the switch.
You cannot have a switch stack containing a mix of Catalyst 3850 and Catalyst 3650 switches.

Small business switches and CDP

what switches in the small business category support CDP?
I took a look at the SGE and SFE series but nothing was mentioned about CDP support. I would like something lower grade than the ESW series if possible.

You may want to take a look at the Cisco Small Business 200 and the 300 Series switches, both switch lines now support CDP.

How to setup a VLAN on a Cisco Stack

I have 3 3750's in a stack config. I can see Gi1/0/1 - Gi3/0/48 in the console and through the web interface. If I do show vlan it shows VLAN1 and shows included ports on all three switches 1/0/1 - 3/0/48. I try to setup a vlan331 on Switch 1 port 17 - Switch 3 port 48
config t
int vlan331
interface range Gi1/0/17-3/0/48 OR interface range Gi1/0/17-Gi3/0/48 --barks at the 3/0/48. It does let me do a test like interface range Gi1/0/17-18. That works..
How can I include the other ports on the other two switches which are stacked into this one VLAN331?

Disclaimer
The Author of this posting offers the information contained within this posting without consideration and with the reader's understanding that there's no implied or expressed suitability or fitness for any purpose. Information provided is for informational purposes only and should not be construed as rendering professional advice of any kind. Usage of this posting's information is solely at reader's own risk.
Liability Disclaimer
In no event shall Author be liable for any damages whatsoever (including, without limitation, damages for loss of use, data or profit) arising out of the use or inability to use the posting's information even if Author has been advised of the possibility of such damage.
Posting
int range g1/0/17 - 48 , g2/0/1 - 48 , g3/0/1 - 48

How to setup Private VLAN in Small business switch SF200-24

Similar Messages

Maybe you are looking for