How to setup QoS for IP/Mac Address WRVS4400N

I need some help setting up QoS for two Cisco/Linksys devivces on my network.
Network devices are Comcast SB6120 modem into WRVS4400n (v2.0.2.1 firmware) that divides into one 24 port gigabit Netgear unmanaged switch, 1 port into AT&T Cisco Microcell, 1 port to HP Officejet 7700 wired printer. Unmanaged switch has approx 10 devices attached (including another 8 port unmanaged gigabit switch). 3 static leases are defined for the network for three devices (HP OJ 7700 printer, Cisco/Linksys PAP2 VOIP adapter, windows home server v1. DHCP is handled by WRVS4400n. Comcast service provides 12mbps of service upstream, 4mbps downstream.
Need to setup QoS for AT&T Microcell and PAP2 VOIP adapter. The real issue that I can't figure out how to configure is IP based priority access. I can do rate control for an IP address but can't figure out how to specify priority control for an IP.
Here are my the current config questions:
1. Bandwidth management page: For the microcell device plugged into port 1, do i set the default CoS to 4 or 1?
2. Bandwidth management page: Should the bandwidth management type be set to priority? I assume yes since I need to define the UDP/TCP ports for priority. The major issues here are
a) one of the ports the Microcell uses is secure https (TCP 443) which is could also be used by any other internet device.
b) can't specify priority for the PAP2, since it's behind the unmanaged 24 port switch
3. QoS setup page: Do I need just 2 queues (one for the port ID for the Microcell and one for the IP address of the Linksys adapter)?
4. QoS setup page: I assume I need to define DSCP for the unmanaged switch but not sure how to tie a queue to an IP address
4. QoS setup page: Shoud priority 0 be set for the most important queue (microcell) and the priority 1 CoS be for the VOIP adapter? Again, not sure about how to define priority by IP address.
5. DSCP setup page: As far as I can find, there's no documentation on how to setup this page.

That's what I do. I keep it simple, one calendar, one set of contacts.
iCloud is really the simplest way to go, as it will sync your (eventual) single Contacts and Calendar across all your devices.
I would:
Figure out which single calendar (in Calendar.app) and contacts (in Contacts.app) that you want to keep.
I'd make a backup of each one. For example,
in Contacts, File > Export... > Contacts Archive...
in Calendar, File > Export... > Calendar Archive...
Make a backup of the other calendar events and contacts that you want to save.
delete all the contacts and calendars from your phones and your iPad.
add the contacts and events from the backups to the single calendar in Calendar.app and your contacts in Contacts.app on your iMac. There is probably some way to export the contacts and events you are adding, and then combine them, but you could also just add them manually.
Then when you configure all your devices for iCloud, they will be all synced automatically.
Message was edited by: arthur

Similar Messages

WRT54GL V 1.1 : how to reserve IP for specific MAC address using DHCP

My !free! made in China router have this functionality. And yet I have been banging my head with this new reasonably expensive wireless router from Linksys. Anyway I lug my notebook around. I need my home router to be able to automatically configure notebook IP address using DHCP. At the same time I need the ip given by home router through DHCP to be the same IP all the time. So "static" ip is not the solution. Alternative "static" ip is also not a solution. Anything with the word "static" in it is not a solution. I know about third party firmware (wrt or tomato) and I know WRT54GL can be flashed with this third party firware. But I'm not going to void my warranty. This will be my last option but not the solution that I seek. I would like to know how to reserve ip for specific mac address using DHCP for WRT54GL V1.1. If this version have no way to make such configuration, I would like to know if there is official firmware upgrade that address this. Thanks in advance!

LDK-Anc wrote:
Tonik - For the life of me, I cannot find DHCP Reservation on the WRT300N. I'm currently configuring one and it would be really useful if I could fine it. Maybe LinkSys calls it something else, but I don't really see anything resembling it. Help!
Maybe these could help. (Images extracted from the User Guide)
Setup tab: Basic Setup
DHCP Reservation
Message Edited by denman_v2 on 03-25-2008 05:11 PM

How can i use my ipod mac address to find it?

simply put, i left my ipod at work. they missplaced it, now i need to locate it... p.s. its only a 3rd gen 32 gig so its not ios 7 campatible ,icloud only works if you have the device and download cloud on to it(and icloud is turned on).....not looking for opinions just looking for options such as: how can i use my ipod mac address to find it? i do have the mac address

You cannot.
If you did not set up find my pod on the iPod itself, then it cannot be tracked.
Sorry

How to specify in the ISE mac-address with its description?

Hello :-)
I want to implement ISE 1.2.
We have a database of mac-addresses and their description (for example the phone with the Mac address, John).
When connecting the phone John to a wifi network, WLC checks its mac-address in the database and allows access.
How to specify in the ISE Mac address with its description?
In the endpoint settings in ISE 1.2 there is no description field. We have ISE1.2.1.198, vWLC 8.0.100, AIR-LAP1131, MS AD (Win2003).
How can I handle this situation? Any ideas?

This link http://www.cisco.com/c/en/us/td/docs/security/ise/1-2/user_guide/ise_user_guide/ise_man_network_devices.html about managing network devices(router,switch), not endpoints(phone, notebook).

How to set the IP and MAC address in C program?

My working environment is Sun250 Server, Solaris 7 operating system. I encountered a problem ---- How to set the IP and MAC address in C program to make the system change it IP & MAC at runtime?
Any idea is welcome! Thanks!

Hi
As a simplest possible solution, you can use the system command
to run ifconfig that can set both the mac address and the IP address of the system. You will have to use setuid though.
Or you can use the DLPI calls ( do a man DLPI or search for a
Sun documentation on the same at http://soldc.sun.com) to write
a pure C program.
HTH
Shridhar

How to setup "Back to My Mac" on iCloud.

Does anyone know how to setup Back to My Mac on iCloud? I never had MobileMe, and all the instructions I find online are for MobileMe. It seems like a really cool concept, though.
The computers I have are a Mac Pro and a Macbook Pro. Both running the latest update of Lion.

I've done that. It goes through as if there are no problems, but I still can't use it. Also, when I try to login using my apple ID, it doesn't work. I've gone to the Airport Utility and tried setting up my apple ID with the mobile me tab, but it asks for my me.com username and password. I never had a password for it, because I setup using cloud. I put in my apple ID password anyway, but there is still no luck. It tells me my username or password is incorrect.

WLC - How to block a single client MAC address?

Hi Sir,
On a WLC (software version 4.1.185.0), how to block a single client MAC address?
I thought of using the SECURITY -> Disabled Clients. Is it right?
There are currently 250 users connected to the WLC. MAC Filtering is not a scalable solution because as I understand it, we have to specify all the legitimate MAC addresses in the local database.
Thank you.
B.Rgds,
Lim TS

Hi Lim,
As you have discovered, the Mac filtering on the WLC is an Allow (based on Mac address) rather than what you need which is a Deny (based on Mac address). I have not tried this feature but I think you are on the right track in using the Exclusion List (Blacklist) feature. Have a look;
Use SECURITY > AAA > Disabled Client then click New or MONITOR > Clients then click Disable to navigate to this page.
This page allows you to manually Exclusion List (blacklist) a client by MAC address.
Add the MAC Address and an optional Client Description for the client to be disabled.
Note When you enter a client MAC address to be disabled, the Operating System checks that the MAC address is not one of the known Local Net clients ( Local Net Users), Authorized clients ( MAC Filtering), or Local Management users ( Local Management Users) MAC addresses. If the entered MAC address is on one of these three lists, the Operating System does not allow the MAC address to be manually disabled.
Hope this helps! Let us know.
Rob

How to setup variants for webdynpro report in ABAP? Help!

Hi Experts,
I have a webdynpro for ABAP report with selection screen.
How to setup variants for webdynpro report in ABAP?
Thanks
Gopal

Hi Gopal,
There is no concept of Variant in Webdynpro ABAP. But in our project we have some tool to do that. Its not release to the client I think. In my scenarieo, We create the Screen variant and program name will be supplied to the tool that will generate the ouput in PDF and Selection screen in One view. But the same is not avilable .
If you want the same concept in Webdynpro ABAP, you need to go for Dynamic programming only. This is the only option is avilable.
Warm Regards,
Vijay

How do I set timed access for specific mac addresses?

My daughter tends to stay up late on social media long after we've asked her to go to bed, so I'd like to use the AirPort Utility to just shut off her internet access during set hours. It looks fairly straightforward to set up, however, I don't know how to find her MAC address for her iPod. Can anyone enlighten me?

iPods, IPhones, and iPads do not have a MAC Address.
On the iPod home screen, tap Settings
Scroll down and tap General
Tap About
Scroll down to locate the Wi-Fi Address
Use the WiFi Address of an iPod, iPhone, or iPad in place of the MAC Address when you are setting up rules in Timed Access.

How do i see the whole mac address for my iphone 5C?

The Wi-Fi (MAC) address show in Setting>General>About only shows 4 pairs with ... after the 4th pair. How do I see the last two pairs? Touching the ... or anything else on the screen doesn't help.

This is my friends iPhone and though I checked all of his settings I don't see anything turned on or checked that would make the fonts larger than normal.
I checked this because my iPhone 6 doesn't have this problem.
I was able to find a solution on another sight though. It was suggested that if the entire MAC address didn't show to just touch and hold the visible number until 'copy' shows. After copying the number just paste it into a text message field and the entire number then shows up. Viola!
Its a shame that I had to spend so much time researching this to find it on a non-Apple sight to get this simple answer to a very frustrating glitch.

How do i find the internet MAC address for my MBP?

I am trying to get my MBP integrated into my home wireless network. Need to enter MAC address.

System Preferences > Network, select the connection type (probably Wifi). Advanced button > hardware tab.
The MAC address is listed there.
MAC address filtering is not actually adding any security to a wifi network, so you may want to turn that off - it is trivial to spoof a MAC address & they are visible to anyone in range. Use WPA2 with a good password if you can.

I can not for the life of me setup googlesync for my Mac contacts andiPhone

I have tried everything.I already have a google account so I followed the guide and setup exchange on my iPhone and iPad and turned off MobileMe, the iPhone and iPad did successfully sync contacts in the exchange section but then I needed to setup my Mac adress book to also sync with google contacts. I went to adress book preferences and checked sync with google then entered my google account info, I hit the sync button on the menu bar and nothing went to google contacts on the web, I do not have any contacts at all in google contacts but I do have about 50 on my Mac my iPhone and my iPad.
Basically I am desperate to get this to work I've been trying for hours, all I want is if I add a contact either in my iPhone, my iPad or in my Mac address book for it to be added to all other places, is this possible?
As of now I deleted all exchange accounts and turned MobileMe back on so everything would go back to normal..
How do I set all this up? Thank you for any help.

I'm not sure why the Address Book/Google sync isn't working, but I have had issues with the Address Book sync features in the past. If all else fails, you could instead set your iPad to sync with your Mac's Address Book when you hook it up to your computer physically. When connected, select the iPad in the Devices section of iTunes, and go to the Info tab and click Sync Address Book Contacts.

How to setup dreamweaver for synchronizing website?

Hi, I'm trying to setup dreamweaver 8 in a way that mimics my
online website. The problem I am having is that on my real sites'
server I have placed most of the files outsite the public root
(security reasons), and I'm not sure how to setup dreamweaver so I
can synchronize with this. I am running a WAMP configuration for my
test / development machine.
Online website structure:
some_folder
-source code
- includes files etc..
public_html (document root)
- html files
-images
-css
An example of how my apache virtual host is setup
Document Root: C:\mysite\public_html //This works fine...
If I setup a site in dreamweaver that uses C:\mysite as the
root, the setup resembles the online one. But there is a problem
with this because it uses C:\mysite as the "document root" whereas
the folder C:\mysite\public_html should be the document root. Now
if I change my document root to C:\mysite\public_html then I don't
have access to any of the files above this directory... I'm kind of
screwed with each option I take...

Here are the email server settings that work for me on iMac or iPad using Mac Mail program.
Verizon changed to different email server.
Make sure password for account is correct by resetting password:
Reset password by clicking "I cannot access my account link" on page or login below
https://login.yahoo.com/config/login?.intl=us&.partner=vz-acs&&.lang=en-US&.intl =US&.done=http://hom...
Enter username here to reset password :https://signin.verizon.com/sso/forgotflows
Passwords must match for verizon yahoo & verizon account.
email server settings:
Example
Name: john smith
email address:[email protected]
user name: john smith (Do not use full email address here)
Incoming Mail Server: incoming.yahoo.verizon.net
SSL: on (Port 995)
Authentication: Password
Outgoing Mail Server: outgoing.yahoo.verizon.net
SSL: on (Port 465)
Authentication: Password
user name:johnsmith
Password: current password for account
Save all settings and check for new email. Good luck.

How to assign static ip via mac address on LINKSYS WRT54G2

? how do i assign an ip per mac address with this router? i can't seem to find the option and its becoming a real pain
on my buffalo router i can paste a mac address and assign and ip for each mac on my network

The feature that you are looking for is called "DHCP reservation". This feature is not available on the WRT54G2. Several of the newer Linksys wireless n routers support this feature.
You can assign your computer a fixed (static) LAN IP address, however, you will need to do it manually. Linksys has some very specific rules about assigning fixed LAN IP addresses. Be sure to follow them carefully.
Rules for using fixed LAN IP addresses on Linksys routers:
With Linksys routers, a fixed (static) LAN IP addresses must be assigned in the device that is using the address. So you need to enter the fixed address in the computer or printer, not in the router.
When using a Linksys router, any fixed LAN IP address must be outside the DHCP server range (typically 192.168.1.100 thru 192.168.1.149), and it cannot end in 0, 1, or 255.
Therefore any fixed LAN IP address would normally need to be in the range of
192.168.1.2 thru 192.168.1.99 or
192.168.1.150 thru 192.168.1.254
assuming you are still using the default DHCP server range.
Also, in the computer, when you set up a static LAN IP address, you would need to set the "Subnet mask" to 255.255.255.0 and the "Default Gateway" to 192.168.1.1 and "DNS server" to 192.168.1.1
It is also important that no two devices on your network be set to the same static LAN IP address.

How to collect intranet user's MAC address from web part on document library

I need the best solution for the following problem:
Let's say for an intranet application just to do customization through a web part on a document library we need to collect MAC address of all user's machine who tries to access the particular document library.
main point to achieve is we want to give access only to few users to a particular document library. I think if we get unique mac address then also purpose can be solved. Is there any other way apart from mac?
In SharePoint 2013 on premise application what is the best way to do this customization? early reply is highly appreciated.
Thanks,

Hi,
Why do you need this? SharePoint runs on top of ASP.NET so its limited to what ASP.NET can do. A quick google returns results like:
http://www.codeproject.com/Questions/303612/How-to-get-Mac-Address-of-Client-Machine-in-asp-ne
It's highly unlikely you can achieve this, back to my first question - why? Maybe you can achieve the requirement in a more supportable manner. I'm assuming you want to track the user.
Thanks
Dave
My SharePoint Blog - http://www.davehunter.co.uk Twitter -
@davehunter

How to setup QoS for IP/Mac Address WRVS4400N

Similar Messages

Maybe you are looking for