How to setup rac

Dear friends
Hello
I m setting up rac on 2 database , i have 2 questions:
1- Can i set up its on 2 different hardware , one : HP8420 / HPUX , tow : HP4440 / HPUX
(one database on first machine and the other database on second machine)
2- Can i set up its on different operation system , i.e one of the on HPUX and
other on WINDOWS NT .
Regard
A.Jafari

Hi Jafari,
On the same cluster, you can't have different Operating Systems. But RAC are available for several Operating Systems like Linux, HP-UX, Solaris, Windows and others.
Rac uses one database managed by more the one instances. You can have more than one database runing on RAC systems and this signify more instances runing at same node, like stand alone environment, if you has more than one database on same machine you must run more than one Oracle instances.
The RAC architecture is different, but not too much.
Regards,
Rodrigo Mufalani

Similar Messages

  • How to setup rac scan on OEL6 on virtualbox

    I am trying to setup RAC on a 2 node cluster. i am trying to setup rac scan.
    i have 2 ip address
    192.168.8.1 - public  node 1
    192.168.8.2 - public  node 2
    192.168.1.1 - private node 1
    192.168.1.2 - private node 2
    VIP Ipaddress
    192.168.8.6
    192.168.8.7
    192.168.8.8
    the scan ip's are
    192.168.8.3
    192.168.8.4
    192.168.8.5
    NOTE: i have an active directory network in house that uses the public ip's subnet above. which also act as my DNS servers. The public ip's are connected to the internet. so all my linux boxes are browsing
    i have added all the ip's to my host file. and installed dnsmasq. and followed the steps on oracle-base. i have two nic on virtualbox. one bridged to the host system and acting as my public ip (192.168.8.0) while the other is an internal network for the private network(192.168.1.0)
    ORACLE-BASE - Dnsmasq : For Simple DNS Configurations

    Your /etc/hosts file should be like:
    # public
    192.168.8.1     node1
    192.168.8.2     node2
    # private
    192.168.1.1     node1-priv
    192.168.1.2     node2-priv
    # VIP Ipaddress
    192.168.8.11     node1-vip
    192.168.8.12     node2-vip
    # scan ip's are
    192.168.8.3     cluster-scan
    It is better to define 2 NICs for each VM: 1 for public networking and 1 for private.

  • How to setup private network in oracle rac

    Hi all,
    Iam trying to setup oracle 2-NODE RAC ,
    now i stuck in setup private network..
    how to setup private network, what i have to do for that.
    please help us provide step by step process

    The loop is nothing but a network cable connecting two nodes on same port with a private IP address (something like 10.0.01 and 10.0.0.2) which is not accessible by any other machine in the network (except 2 nodes obviously ).
    Note that cross over cables are not supported for the Cluster Interconnect. And cross over cables limit the cluster to only 2 nodes, which may not be enough for many RAC deployments.
    Cheers,
    Brian

  • How to install RAC on windows

    Can anyone tell me step by step how to install RAC on windows advanced server. I want to know whether RAC must need Microsoft Clust Service. When I create a cluster with clustersetup.exe, I'm told that it's need oracle partition, but I don't know how to make it.
    thanks advance!

    Hi, I am Nirmal ([email protected]) Please try this out
    Requirements:
    H/W: External shared hdd
    RAM: 256 MB
    OS:win Advance server ,win 2000
    PATCH:
    The Windows CFS and Clusterware Patch for 9.2.0.6 -- available in Metalink under Patch number 3973928
    The 2.2.0.18.0 Oracle Universal Installer -- available in Metalink under Patch number 2878462
    The 9.2.0.6 RDBMS patchset -- available in Metalink under Patch number 3948480
    1.Install shared disk array.
    2.Install cluster interconnect and public Network hardware
    a)Create two entries of NIC-Ensure Public IP listed at the top and private IP should be listed below the public IP.
    b)Inter connection between two nodes are connected by switch.
    3.Ensure the IP/Hostname of all node is entered in hosts file.
    4.Ensure the temp /tmp directories are same accross all node.
    5.Ensure that all nodes have same local admin name which has full access on the oracle home drive and win home drive.
    6.Run the final clustercheck which is available in patch 3973928 which will check the above process if any incorrect it will indicate.(Location is 3973928\Disk1\preinstall_rac\clustercheck subdirectory).
    7.Prepare the Logical Drives in Windows dont format or give any drive letter.
    8.Install and Configure Cluster software with RAW Datafile.
    a)Install oracle home on NTFS partitions and Datafile on Shared Logical Partition.
    9.Run Oracle cluster setup wizard.
    a)Click clustersetup command line.
    b)A welcome page launches click next.
    c)Create a cluster. click next.
    d)Choose "user private network for interconnect" and click Next.
    e)Network config page appears, enter the cluster name. then enter the public hostname for all nodes. Accept the default or change as appropriate for your cluster configuration. click next.
    f)Cluster file system option page appears. Choose No Cfs. click next.
    g)Disk config page appears. Click "Create Oracle Symbolic links button" label as srvcfg to the partition we have created.
    h)Oracle Object link Manage window appears:
         1)From symbolic Link column, select an empty row.
         2)Type in the desired datafile link name and hit enter to save
         3)click apply button to commit.
         4)When the progress bar at the bottom of the screen stops      moving choose close.
    i)VIA Detection screen appears. Choose yes or no depending on your config.(VIA-Virtual Interface Architecture).
    j)Install location screen appears. its default win_home\system32\osd9i accept .click finish.
    k)Cluster setup window appears if no error it will complete and close automatically.
    l)Check the serices,
         1.oracleobjectservice
         2.oracleCMService9i
    (if any error check the error log)
    10.Install the 22018 OUI
    a)home oracle_home.
    b)Click all nodes and install.
    11.If necessary install RDBMS Software into oracle home.
    RAC Database using DBCA::
    a)Create listeners using Net configuration assistant on each node
    b)Run DBCA from command prompt.
    c)Welcome page displays with the selection to create a cluster or
    single instance database. choose oracle cluster database. next
    d)Operation page is displayed. choose create database. Next.
    e)Node selection page. Select all nodes. Next.check OracleGSDService
    is running on all nodes.
    f)Database Templates page is displayed. Choose new database. next.
    g)Database Identification page. Enter the Global Database name and
    SID (oracle will register SID prefix with a number, this will
    become the SID of each node.)
    h)Option page for java and inter media database. Choose according to
    your need.
    i)Connection option select dedicated or shared server .
    j)Initialization parameter page. Add required values.
    k)Database storage window.(ensure the storage information points to
    the symbolic links specified in cluster.)
    l)Creation page displayed, click finish.
    m)DBCA summary page click create database and ok.
    Note:
    1)During Java creation it may slow down or hang. Check the CPU
    usage and at 95-99% it will slow down please wait check the log.
    2)ORA-29807 error may come. Ignore it its a (bug 2925665).
    3)alter installation run the script prvtxml.plb, utlrp.sql
    4)Any other error please check the alert log.
    Message was edited by:
    user474717

  • How to setup the raw devices  permissions permanantly in 11gr2  on RHEL 5.

    Hi All,
    Succesfully installed 11gr2 RAC and working fine , but in next boot raw devices permissions revert back to root .
    Please advice me to how to setup permissions permanantly as the oracle user.
    Regards
    San
    .

    you find the lib on this page:
    http://www.oracle.com/technetwork/topics/linux/downloads/rhel5-084877.html
    in the AMD64 / Intel em64t Architecture table
    this is the direct link
    http://oss.oracle.com/projects/oracleasm/dist/files/RPMS/rhel5/amd64/2.0.5/2.6.18-194.el5/oracleasm-2.6.18-194.el5xen-2.0.5-1.el5.x86_64.rpm
    hth
    p.s. don't forget to mark question as helpful/correct and close the question.

  • How to install rac on the vm ?

    how to install rac on the vm ?
    Hi everybody,
    i want to install to Oracle RAC on the 2 nodes.
    i installed oracle enterprise server on the servers.
    And i have' t got a another storage, so i shared the disks of the node1 and i mounted the disk on the node2. when i share disk, i used the nfs file system.
    This method is a problem for the setup, will you?
    DO you explain step by step how to install oracle 11g rac on the vm ?
    thanks.

    Hi,
    DO you explain step by step how to install oracle 11g rac on the vm ?Refer link:
    http://www.oracle-base.com/articles/11g/OracleDB11gR1RACInstallationOnOEL5UsingVMwareServer2.php
    Regards,
    X A H E E R

  • How to setup three SharePoint sites on one server?

    Hello,
    How to setup three SharePoint sites on one server?  I have three sites like:
    http://site1
    http://site2
    http://site3
    And need to have them running up on one server. I recall some changes need to be done to the host file, but not sure.  Can you advise on what to change?
    Thanks,
    Paul
    Paul

    you need to make entries in DNS to get this done.
    check here:http://spshare.blogspot.com/2012/05/how-to-create-host-header-web.html
    nice blog with step by step explanation:
    http://thuansoldier.net/?p=1323
    Please remember to mark your question as answered &Vote helpful,if this solves/helps your problem. ****************************************************************************************** Thanks -WS MCITP(SharePoint 2010, 2013) Blog: http://wscheema.com/blog

  • How to setup multiple base station under one network?

    How to setup multiple base station under one network? I have 6 rooms but one airport base station makes really difficult to get good signal from every rooms. I wonder if I can setup multiple airport base stations talking to each other under the same network to build up the signal strength will help solve this problem. But, is it possible? How?

    One route would be to utilize a "roaming" network. In a roaming network, you would connect multiple AirPort Extreme Base Stations (AEBS) to the same Ethernet. Of course, this would require that your home is already wired for Ethernet.

  • How to Setup SSL on Oracle Application Server 10g Release 2 (10.1..2)

    Hi All,
    Can anybody tell me How to setup the SSL on Oracle Application Server 10g Release 2 (10.1.2).
    I have all the required documents like
    1. Oracle Application Server Portal Server Configuration Guide.
    2. Oracle Application Server Web Cache Configuration Guide.
    3. Oracle Application Server SSO Administration Guide.
    I tried to follow all this documents but still i am not able to set SSL for Oracle Portal Server.

    The Portal Configuration Guide, available on OTN at http://www.oracle.com/technology/documentation/appserver1012.html does provide some very specific information on how to set up OracleAS Portal.
    Section 6.3.2.1 Configuring SSL for OracleAS Portal describes various configurations, such as:
    SSL to OracleAS Single Sign-On
    SSL to OracleAS Web Cache
    SSL Throughout OracleAS Portal
    External SSL with Non-SSL Within Oracle Application Server
    For larger enterprise configurations, you can refer to the Enterprise Deployment Guide.
    Can you give a bit more background on what you are trying to set up? Which scenario, what sort of hardware, software versions, and so on.
    Regards,
    Pete

  • How to setup a static IP for a wireless printer

    This problem has been ongoing for several versions of OS X and the last five printers I've had and I'm finally over messing with it.  For some reson, when using a wireless printer with OS X this is a repetetive problem, and I think if I configured the printer to a static IP address instead of using DHCP, it might work better.  At least once a week, if not more often, I'll print something and get the ubiquitous Dock error of "Printer is not connected".  The printer is still in Preferences, but if I delete it, then it doesn't show up as it should for selection.
    The only way to fix this is reboot, and then the printer shows up again in Preferences.  I select it and all is well again...until a few days pass and the same thing happens again.  Using an HP LaserJet P1102w, still a current model, but it doesn't matter which printer I use.  I also have an Epson Artisan 725 and the same thing happens with it about once a week.  Also, this happens from both my Mac and my wife's Mac, so it's not an issue with just my machine.
    I've searched for documentation on how to setup a static IP address for a wireless printer with the Airport Extreme, but all I find are tutorials on how to do it with an ethernet hard-wired printer.  Any help would be greatly appreciated.

    You could set up your router to do manual assignment of IP address instead of using DHCP, but that is a PITA, because then you'd have to manually set up IP for all your devices.
    If you have AirPOrt Extreme, you could do this:
    In your Apple TV, go to the Settings >> About and write down the MAC address of your ATV
    Start up the AiPort Admin Utility
    Go to Network tab
    click + in the DHCP reservations
    Choose an IP you want for your ATV & Enter the MAC address
    From now on, this IP address will be reserved to the MAC address and only your ATV will be able to get it, no other device will.
    It is not a static IP in a true sense, but behaves just like one.
    Works great for me...
    If you don't have a AP Extreme, I'm sure other routers will allow you do reservations too.

  • How to setup Charms in a 2 tier landscape ?

    Hi All,
    We have a two tier landscape i.e only having development and production system so how to setup STMS and all other settings in this type of scenario.
    Can we use Virtual system in STMS as a Quality system ? If yes then please guide us and tell me how to proceed as if we dont know how to add virtual system in SMSY in solman. Please provide us with a clear picture and give us detail documentation if possible.

    Hi All,
    Please tell me as per the SAP standard recommendation is it necessary to have a cycle like DEV->QUAL-PROD for Charms as we are not having any Quality system or Client here in our landscape.
    Please suggest a way how to proceed in this case. Please help me out.

  • How to setup breakpoints in a vector space?

    Hi,
    How to setup breakpoints in a 2D vector space in NI 7344 and check for them using flex_read_breakpoint_status_rtn?
    Thanks.

    Hi,
    Is Office Communicator something to do with the Word, Exel and Powerpoint Office Package ?
    What sort of Screen Names or IDs do you use with that ?
    If these are MSN/Live accounts names then it can be made to work for Text Chats but not Video or Audio Only chats
    10:38 PM      Friday; April 20, 2012
    Please, if posting Logs, do not post any Log info after the line "Binary Images for iChat"
      iMac 2.5Ghz 5i 2011 (Lion 10.7.2)
     G4/1GhzDual MDD (Leopard 10.5.8)
     MacBookPro 2Gb (Snow Leopard 10.6.8)
     Mac OS X (10.6.8),
    "Limit the Logs to the Bits above Binary Images."  No, Seriously

  • How to setup iChat in a office

    How to setup iChat in a office that using Office Communicator as a IM ?

    Hi,
    Is Office Communicator something to do with the Word, Exel and Powerpoint Office Package ?
    What sort of Screen Names or IDs do you use with that ?
    If these are MSN/Live accounts names then it can be made to work for Text Chats but not Video or Audio Only chats
    10:38 PM      Friday; April 20, 2012
    Please, if posting Logs, do not post any Log info after the line "Binary Images for iChat"
      iMac 2.5Ghz 5i 2011 (Lion 10.7.2)
     G4/1GhzDual MDD (Leopard 10.5.8)
     MacBookPro 2Gb (Snow Leopard 10.6.8)
     Mac OS X (10.6.8),
    "Limit the Logs to the Bits above Binary Images."  No, Seriously

  • How to Setup Historical DSC Database on a standalone Server

    Hey @all,
    I am looking for documentation how to setup a standalone server for the DSC Module(Ver. 8) Historical Database.
    My aim is to log all data to this server. The Server will be running Win2K.
    Do I have to install the complete Labview 8 software and the DSC Module?
    Does a walkthrough exist how to setup a DSC server?
    Thx!
    Carsten  

    After installing the runtime you should only have to reboot the computer in order to get the citadel service running.  At the point, for citadel purposes, this machine will behave as though you had the DSC development system installed.  The 8.0 runtime has no setup requirements...it should only need to be installed.  Unlike previous versions, 8.0 requires you to build your application into an executable and the runtime should be invisible to you once you install it.  If this is not the case, please post about it so it can be looked at.
    If you have specific questions, please post them and I will either try and help you find the answers, get them posted, or answer them myself.
    Regards,
    Robert

  • How to setup the security based on roles in Organization.

    Hi,
    How to setup the security based on roles in Organization.
    For example:Few users are Manager and a few user are Non Manager .Manager should have access to all work data including Non Manager and Non Manager should access based role.How to setup this? How OBI server identify the user role?
    kindly let me know.
    Regards.,
    CHR

    Hi,
    You need to have Back End support to achieve this. In Back End you need to create two groups . You need to know what joins has to be made for which group (which is more important) and also make session variable for the userrole (with SQL supporting it). In the BMM layer, we need to put the security join conditions in the 'where clause'.
    And make a common report. User loggin in with the respective userid will have userrole and joins assigned in the Back end. And they will be viewing the report according to their access.
    Hope this will solve your problem.
    Regards
    MuRam

Maybe you are looking for