How to setup SCXI1127 in scanner mode with NI-DAQmx

Hi,
I have 2 1127 mux cards in my SCXI frame and a digitizer/DVM in my PC. I am planning to perform a scan on selected channels across both cards using synchronous scanning ( I cannot get handshaking to work ). I found some examples but they are all using initialization string that looks like this: "SCXIn::i,j:CANNER", but that only works with NI-DAQ legacy not NI-DAQmx where my instrument is just called SC1. I do not know how to set it up with NI-DAQ legacy, it will not give me that option ( using NI-MAX I can setup SCXI-1000 but not PCI-4070 ). Also I do not know how to initialize the NI-SWITCH driver so I have it as one instrument with one instrument handle. I am using NI-DMM, NI-SWITCH 3.0, NI-DAQmx 8.0 and MS Visual C++ Express.
Thank you,
Jerry.

Jerry,
This is Travis over at NI.
There are example programs for doing synchronous scanning that ship
with the NI-SWITCH driver. You can access them at
Start>>Programs>>National
Instruments>>NI-SWITCH>>Examples>>C. Choose
"niSwitchDMMSwitchSynchronousScanning." Your resource name will
be the same as the your resource name in DAQmx. Please direct any
further questions to Minh.
Thanks, Jerry. Have a great day!
Travis

Similar Messages

How can I get to DFU mode with a broken power button?

How can I get to DFU mode with a broken power button?

aarons84 wrote:
This is bad, but i tried jailbraking my iphone
You may as well stop there. We can't help you.

How to setup Finger print scanner on home button of iPhone 5?

How to setup Finger print scanner on home button of iPhone 5?

Hi,
If you see this video between - 1.15 to 1.32, you will notice this feature.
http://www.youtube.com/watch?v=3WFjWFLoUC0

Trying to setup 1131 in autonomous mode with multiple ssids and vlans

hi there,
I'm trying to setup an aironet 1131 in autonomous mode with a WLAN for each VLAN.
I can connect to the SSID "BLUGstaff" but I don't pick up a DHCP address and when I set a static IP I can't anything on the vlan so I can only assume I have made an error.
I have attached the config for the access point.
The switch port the access point connects to has the following config...
interface FastEthernet1/0/3
description ## Access Point ##
switchport trunk encapsulation dot1q
switchport trunk native vlan 121
switchport trunk allowed vlan 1,121-124
switchport mode trunk
spanning-tree portfast
end
Can anyone explain what I've done wrong? Thanks in advance for any help,
Huw

Hello Huw,
as i see in your confirguartion.
native VLAN is 121. so you have to correct following in your AP configuration
1) interface Dot11Radio0.121
encapsulation dot1Q 121 native
bridge-group 121 ->>>>>>>>>>>>>>>> change this to brige-group 1 , native always tied to bridge group 1
2)
interface FastEthernet0.121
encapsulation dot1Q 121
add also under this sub interface
bridge-group 1
please let me know how it goes.
Kind regards
Talal
==========
please rate answers that you find useful , and mark as answered - when it is :-) - so others can find it easily

How to setup a Class B network with WRT54GX ver. 2

Hi all,
I bought a WRT54GX ver. 2 router. I wanna know how to setup the IP address say 128.1.50.136 with subnet mask 255.255.0.0 (Class B network)? By the way, 128.1.0.0 is my network zone.
If the router can't change, what should I do? Any other router support Class B network?
Thanks!

bcow wrote:
I did but it doesn't work. It seems don't have 255.255.0.0 to select.
would you state more clear of how to do it? Thanks!
It does not have that because it does not support it... the router runs on CLASS C only because it was designed and made for SOHO only... bussiness lines of Linksys or Cisco can do that....but not this router...
"Sometimes your knight in shining armor is just a retard in tin foil.."-ARCHANGEL_06

How to setup the 'Client Licensing Mode' for Windows server?

Hello,
We will install the SBO server:
OS: Windows Server 2003 Standard Edition
SBO Clients: 150
How should we setup the 'Client Licesing Mode' for the windows server?
If we select the mode "Per server,Number of concurrent connections", how to set the connection number?
Thanks in advance.
Don

Hi..
you can set License to Particular user using License under Administration and Client will automatically fetch License using License Manager on License Server
Regards,
Bhavank

How to setup a Seamless Transaction Gateway with PayPal (Australia Only)

I've been working with the team at PayPal to allow BC Partners to set up a cost effective way to setup a Seamless Transaction Shopping Cart Process on their BC eCommerce website without the need for a 3rd Party Merchant Provider like eWay or Secure Pay or their bank. This is designed for entry level businesses who want to control their setup costs and keep all funds in one place (PayPal).
Currently BC doesn't support Paypal's Payments Pro plan in Australia so you are limited with either a non-seamless payment process or using a 3rd Party Merchant provider with can be costly.
Without going into too much detail, the setup on PayPal's side is a mixture of a couple of plans, and is a little complicated however through our discussions we come to an arrangement of any additional fee's associated with the setup being waived since this is more so of a technical workaround than anything else.
Basically PayPal is the merchant provider, and the customer doesn't leave your website when making a purchase through the Shopping Cart. The setup is only $25/month plus transaction fees of between 1.1 to 2.4% + 30 cents depending on the number of payments (this is just an initial guide and confirmed on your discussion with the PayPal).
Because the setup involves quite a few steps and departments I've arranged a contact that will fast track this process and is familiar with this unique setup.
How to setup PayPal for a Seamless Transaction Process
Sign up for PayPal Business account Timeframe: <20 minutes
Email Peter [email protected] or phone (02) 8288 0333. CC me [email protected] or mention my name so he can correctly setup the process and apply the discounted pricing.
Prepare for the Verification process for the PayPal account (Proof of ID, Proof of Address, Business documents etc).
Wait for Account Verification. You will be informed to setup both PayFlow Pro* and Website Payments Pro (*the PayFlow payment will be waived as mentioned previously). Timeframe: up to 5 business days depending on swift supply of required documentation.
Wait for your Billing Agreement for Website Payments Pro once application has been approved. Sometimes they will receive a phone call to verify details of the application. Timeframe: Up to 72 hours
Login into your PayPal account to accept the Billing Agreement.
Notify Peter once the Billing Agreement has been accepted so your PayFlow Pro can be linked to your Website Payments Pro
Login into your Business Catalyst Website and navigate e-Commerce > Payment Gateways
Select PayPal PayFlow Payment Gateway (..,AU, ..)
Enter your Username, PayPal Password, and add VSA as the Partner
Setting up PayPal Payments
If you also want to make payments via PayPal (ie, with the customers Pay Pal account) you can continue with setting up the PayPal Website Standard secure with your PayPal Customer ID and your PDT Token which you'll need to setup in your PayPal Account.
If you have any questions give me or Peter an email. I'll continue to update this document as I go.
Please note this setup is current for Australian Pay Pal Customers only. This process does not support re-occurring billing.

Dennis, sounds like you are having issues connecting to your network. Here is what we are going to do.
On your first question, and second question for that matter, I would suggest using a WPA password. Our printers doe not associate with the other types as well as WPA. You should be able to do that, though I have not personally set up a router that way to have experience in how it will react with the networked devices. As for the issues you are having, once the settings are all in the correct order I am going to suggest we connect the printer to the network through the computer.
What you will do is install the printer using a USB connection, then re-run the setup software. Here there should be an option for USB to Wireless. This will be the easiest way to be sure that all the settings are correctly transferred over.
http://h10025.www1.hp.com/ewfrf/wc/softwareCategory?cc=us&lc=en&dlc=en&product=303770
You can find the software in the link above.
Let me know if this helps!

Can't find how to shut off File Transfer Mode with...

I've spent the better part of two hours searching the Internet for information on how to turn off File Transfer Mode since my phone started refusing to connect to my home computer, today.
The pdf user's guide doesn't say how to find it. I've been digging through the menu on the phone trying to find anything that resembles File Transfer Mode so I can click it off.
The other FAQ and discussion groups I've located are irrelavent as the information they contain doesn't transfer to my Nokia 820 (they suggest options which don't exist on my phone).
Please, where does one start looking for File Transfer Mode on this phone so they can shut it off, and why isn't that information printed in the troubleshooting documents and self help files for these phones?
I connect through the USB cable to my PC. I have downloaded and installed Nokia PC Suite v.7.1.180.94 this morning in hopes that it would fix the connectivity problem, but unless I can get File Transfer Mode shut off somehow, my new phone's going to wind up being useless.
Nokia Lumia 820, Windows 8 phone
HP Pavilion Slimline s52021, Windows 7 Home

have you searched these forums and tried a soft reset (pressing the volume down and power buttons together until the phone vibrates)? Bear in mind that no, Nokia Suite, or Nokia PC Suite do not work with Windows Phone 8 devices at all, only the Windows Phone app does.
See if other devices connect to your PC, and try other USB ports.

HT1338 How to setup an external HDMI screen with a Mac Book Air

How do I setup an external HDMI screen with a Mac Book Air? I am using an Apple accessory Moshi cable interface with a Samsung Syncmaster screen SB24B300 and I am unable to get any response. Thank you.

You need to connect it to the computer using either USB or Thunderbolt. Setup is simply prepping the SSD:
Drive Partition and Format
1. Open Disk Utility in your Utilities folder.
2. After DU loads select your hard drive (this is the entry with the mfgr.'s ID and size) from the left side list. Click on the Partition tab in the DU main window.
3. Under the Volume Scheme heading set the number of partitions from the drop down menu to one. Click on the Options button, set the partition scheme to GUID then click on the OK button. Set the format type to Mac OS Extended (Journaled.) Click on the Apply button and wait until the process has completed.

How do I boot into recovery mode with wireless keyboard

I am unable to boot into recovery mode using either cmd-R or holding down the alt key. How is it supposed to work?
Message was edited by: Niklas Brunberg (better title)

I understand your concerns - I'm glad both of my machines are dual bootable (just in case) and I have my Snow Leopard install disks..... However, this is what Apple has decided, so we need to find the best way to deal with it. Personally, I've tested the recovery mode several times and, at least on my machine, it was not reliable (i.e. it wouldn't work - I tried it again and it did, but it spent more than an hour downloading the entire 4 GB installer again and then another 30 minutes installing it), and on a third try, I found that it had vanished because I had cloned by drive. When you clone, only your system is cloned, not the extra partition.
So, I've decided to rely on a) my bootable clones and b) a copy of the installer (.dmg) in case my clones fail. I don't feel comfortable relying on something that requires an internet connection and a full download to work. But, that works for me; you may want to take a different approach.

How to setup peer to peer network with Vista machine.

Hello,
I just got my very first Apple computer last week and I'd like to copy some files from my Dell PC with Vista Premium installed. I don't have a wireless network setup yet (hopefully soon), but I'd like to copy some files from my PC to my Mini. I was wondering if it were possible to network the two systems using just an ethernet cable between the two.
Might someone know how to set this up or refer me to a document that explains all the steps needed to accomplish this?
Thanks in advance,
Jeff

Apple have a page that talks you through doing this:
http://docs.info.apple.com/article.html?artnum=304721
Probably a good place to start.

How to setup Supp Life Coverage reduction with age

Hi All,
Ravi,
We have a problem with Supplement life coverage dropping on non flex program window when there is a reduction in age. When somebody moves from 64 to 65, the benefit won’t show up on non flex window after starting a LE (open enrollment) and that causes the self service enrollment page not show up the Supp Life the EE is currently enrolled.
It stays fine for people moving from 65 to 66 (within the range), but someone moving from 64 to 65, 69 to 70, 74 to 75 and 79 to 80, the coverage drops on non flex window. The enrollment results window shows their age 64 coverage amount which is fine.
When we try to enroll the EE already enrolled in Supp Life moving to 65, the list of values on NON Flex window shows that the EE is already enrolled with reduced amount and all we do is save.
We have setup supp life to reduce
•     35% when employee turns 65
•     25% when employee turns 70
•     10% when EE turns 75
•     10% when EE turns 80.
We had setup our variable rate profile Age 65 to 69 Reduction, Age 70 to 74 Reduction, Age 75 to 79 Reduction and Age 80 and Over Reduction with usage type of Coverages
Under Coverage Calculations, we had setup Variable Coverages with the above variable rate profiles. We used rules for calculating the upper limits..
We opened SR and support says that the variable coverages with flat range never worked. They logged a bug, but I am sure there could be many clients who use this functionality and was wondering what would be the best method to solve this problem.
Thanks
Veena

We are using variable rate coverages and the coverage amount is calculated right.
But when LE is started and navigate to Non Flex window to change his enrollments, we donot see the Supp Life benfit for this Employee.
When EE loginto self service to change his/her enrollments, SS doesnot show the EE as being enrolled in Supp Life.

How to setup a 'duplicate/mirror view' with a different zoom level?

Hi Photoshop Gurus,
I constantly keep zooming in and out of the same images. It drives me crazy to view it at normal zoom level and zoom back into deep pixels.
Is there a way so that I have a duplicate floating window/view that shows realtime editing of an image at a different zoom level? (Think of it like a display mirroring, but, I am trying to mirror the same document at a normal zoom level).
This is my scenario:
- I usually work with small images/icons.
- I zoom deeply into an image at pixel level ~3000%.
- Change some pixels and do editing
- Zoom back out to 100% to view how it looks normally.
- Repeat and repeat.
Can I always have a 100% zoomed view along side the same document?
Thanks for your help.
PHOTOSHOP CS5 Mac Snow Leopard

The navigator palette is just another document view. Open it, put it where you want, resize it, and you can use it to control (and see) what part of the docuemnt your zoomed in view is showing.

How to setup Analyzer 7.0.1 with Java plugin 1.4.2_03?

Hi, I use Hyperion Analyzer 7.0.1. The default Java Plugin is 1.3.1_09 and in my environment it is working without any problems. In my company there are other non-Hyperion applications that requires java 1.4 or higher. I noticed that Java Plugin 1.4.2_03 is also available on Analyzer installation CD. So I installed this java version on client computer, but when the applet is started it opens the java 1.3 installation window. I probably need to configure some settings on Analyzer server computer. What should I change on server site of computer to have java 1.4.2_03 (or higher if posible) accepted on client computer? Thanks, Grofaty

In pdf book "Hyperion Analyzer Release 7.0 Administration Guide - P/N: D750770000) on page 129 there is instruction (please see bellow). But in my Analyzer.jsp file are "<hya:" template tags. When I try to replace the template tags with the ordinary text described in bellow instructions I got error from Tomcat app. server - unable to compile jsp file. How to replace clsid number of java JRE to get working a java 1.4 version? Is there any file where <hya: are specified and I could change the "<hya:" variables with constants? Thanks, Grofaty =========================================== Configuring Different Java Plug-in Versions =========================================== The Hyperion Analyzer Java Web Client and Administration Tools Client are configured to use the Sun Java Plug-in 1.3.1_09. Administrators can update the Sun Java Plug-in versions by editing the Analyzer.jsp and Administrator.jsp files static versioning statement. This mandates the loading of the specified version of the Sun Java plug-in. To edit the Analyzer.jsp and Administrator.jsp static versioning statement, perform the following tasks: 1. Open the Analyzer.jsp file using a text editor. 2. Search for the static versioning statement class ID, clsid:. The current class ID value is as follows: clsid:CAFEEFAC-0013-0001-0004-ABCDEFFEDCBA 3. Edit the clsid value, to the desired Sun Java Plug-in version. Alphabetic characters at the beginning and end of the string are set by Sun. Do not change these characters. The first two sets of numeric digits indicate the Sun Java Plug-in version. The third set of numeric digits indicates the patch number. For example, the clsid value for the 1.3.1_10 Sun Java Plug-in is as follows: clsid:CAFEEFAC-0013-0001-0010-ABCDEFFEDCBA 4. Save your changes to the jsp file. 5. Repeat all of these steps for the Administrator.jsp file.

How to setup SMBX client for work with Windows 2003 server's shared folders?

Dear community,
Some folders within shared folder on Windows 2003 Server is not visible for MacOS 10.8 client.
How should I set up SMBX? Is there manual?
I know, there is simple solution to type exact pathname (with those invisible folders) in connection dialog, but it is not usefull for me.
Thank you in advance

Hi,
Please remove the 3 non-exists DC from environment using the metadata clean-up process using script from below article. then manually delete the records from DNS management console as given below.
https://gallery.technet.microsoft.com/scriptcenter/d31f091f-2642-4ede-9f97-0e1cc4d577f3
Manual steps to clear the records.
Dnsmgmt.msc [Dns Management]
A.Expand the forward lookup zones\_msdcs folder
i. Make sure only the actual domain controllers are listed, delete wrong Alias recordsremove wrong name server records
ii. Select the container [forward lookup zones\_msdcs.domain.com\dc\_sites_\sitename\_tcp] > delete incorrect _ldap and _kerberos records are listed.
iii. Select the container [forward lookup zones\_msdcs.domain.com\dc\_tcp] and delete incorrect _ldap and _kerberos records
iv. Expand the [forward lookup zones\_msdcs.domain.com\domains\guid\_tcp] and delete incorrect _ldap entries
v. Select [forward lookup zones\_msdcs.domain.com\gc] – delete incorrect HostA records
vi. Expand the [forward lookup zones\_msdcs.domain.com\gc\_sites\sitename\_tcp] – delete incorrect _ldap entries
vii.Select the [forward lookup zones\_msdcs.domain.com\gc\_tcp] – delete incorrect _ldap entries
viii. Select the [forward lookup zones\_msdcs.domain.com\pdc\_tcp] – delete incorrect _ldap entries
B.Expand the forward lookup zones\domain.com folder
i.Delete Host(A) records of dc’s which are non-existant.
ii.Correct the NameServer (NS) records
iii. Follow steps similar to ’ A ii ‘ >> ‘ A viii’
· Dssite.msc [Sites and Services]
A.Expand the [Sites\Sitename\Servers] – delete incorrect server’s
B.Delete incorrect subnet configurations [Sites\Subnets]
C.Delete incorrect site links [Sites\IP]
· Make sure the domain controllers are pointing to the correct dns servers in tcp\ip settings.
· Force replication – ‘repadmin /syncall’

How to setup SCXI1127 in scanner mode with NI-DAQmx

Similar Messages

Maybe you are looking for