How to setup WPA?

I'm connected to DSL through a wireless router. How do I set it up so that it requires a password to connect? The router is NETGEAR.

Nevermind. I figured it out. I had to go back into the Netgear setup gateway site and set it up from there under wireless settings.

Similar Messages

How To Setup WPA on WRT54G?

I have looked everywhere but cannot seem to find a how-to guide on WPA.
Everything I hear says WPA is more secure than WEP, but if it automatically exchanges keys, what prevents someone else from hopping on the wireless? My thought is it has something to do with an initial code to connect it to the network... but won't this just be like WEP?
I just need a how-to guide how to setup WPA.
I have a WRT54G v3.1 with latest firmware, and am using XP SP2 with latest updates. The card is non-linksys (I want to say Broadcom, but I am not sure).
Just need to know what to configure on the router and my PC.
From what I understand Personal vs Enterprise (If I remember, maybe it is called Corporate or something) is that the non-personal version requires a server, which I don't have. So I need personal.
The router does also have WPA2 on there, I do not know the differences but I would assume it to be better than regular WPA.
Thanks!

You may go to the linksys router set up page http://192.168.1.1 leave username blank and admin is the password.
Click on the wireless tab and the sub category tab under wireless the wireless security , you can choose wpa on the security mode, choose TKIP as the algorithms, on the pre-shared key typed in here your password for your wireless, this will server as your network, it should be at least 8 characters long. Leave it on 3600 seconds.

How to setup a password protection in my wireless airPort?

How to setup a password protection to my wireless AirPort?

To configure the AirPort base station for wireless security, you will need to use the AirPort Utility.
AirPort Utility > Select the AirPort > Manual Setup > AirPort > Wireless tab
Wireless Security: <None | WEP (Transitional Security Network) | WPA/WPA2 Personal | WPA2 Personal>
Wireless Password: <enter your desired password>
Verify Password: <reenter your desired password>

How to setup a Seamless Transaction Gateway with PayPal (Australia Only)

I've been working with the team at PayPal to allow BC Partners to set up a cost effective way to setup a Seamless Transaction Shopping Cart Process on their BC eCommerce website without the need for a 3rd Party Merchant Provider like eWay or Secure Pay or their bank. This is designed for entry level businesses who want to control their setup costs and keep all funds in one place (PayPal).
Currently BC doesn't support Paypal's Payments Pro plan in Australia so you are limited with either a non-seamless payment process or using a 3rd Party Merchant provider with can be costly.
Without going into too much detail, the setup on PayPal's side is a mixture of a couple of plans, and is a little complicated however through our discussions we come to an arrangement of any additional fee's associated with the setup being waived since this is more so of a technical workaround than anything else.
Basically PayPal is the merchant provider, and the customer doesn't leave your website when making a purchase through the Shopping Cart. The setup is only $25/month plus transaction fees of between 1.1 to 2.4% + 30 cents depending on the number of payments (this is just an initial guide and confirmed on your discussion with the PayPal).
Because the setup involves quite a few steps and departments I've arranged a contact that will fast track this process and is familiar with this unique setup.
How to setup PayPal for a Seamless Transaction Process
Sign up for PayPal Business account Timeframe: <20 minutes
Email Peter [email protected] or phone (02) 8288 0333. CC me [email protected] or mention my name so he can correctly setup the process and apply the discounted pricing.
Prepare for the Verification process for the PayPal account (Proof of ID, Proof of Address, Business documents etc).
Wait for Account Verification. You will be informed to setup both PayFlow Pro* and Website Payments Pro (*the PayFlow payment will be waived as mentioned previously). Timeframe: up to 5 business days depending on swift supply of required documentation.
Wait for your Billing Agreement for Website Payments Pro once application has been approved. Sometimes they will receive a phone call to verify details of the application. Timeframe: Up to 72 hours
Login into your PayPal account to accept the Billing Agreement.
Notify Peter once the Billing Agreement has been accepted so your PayFlow Pro can be linked to your Website Payments Pro
Login into your Business Catalyst Website and navigate e-Commerce > Payment Gateways
Select PayPal PayFlow Payment Gateway (..,AU, ..)
Enter your Username, PayPal Password, and add VSA as the Partner
Setting up PayPal Payments
If you also want to make payments via PayPal (ie, with the customers Pay Pal account) you can continue with setting up the PayPal Website Standard secure with your PayPal Customer ID and your PDT Token which you'll need to setup in your PayPal Account.
If you have any questions give me or Peter an email. I'll continue to update this document as I go.
Please note this setup is current for Australian Pay Pal Customers only. This process does not support re-occurring billing.

Dennis, sounds like you are having issues connecting to your network. Here is what we are going to do.
On your first question, and second question for that matter, I would suggest using a WPA password. Our printers doe not associate with the other types as well as WPA. You should be able to do that, though I have not personally set up a router that way to have experience in how it will react with the networked devices. As for the issues you are having, once the settings are all in the correct order I am going to suggest we connect the printer to the network through the computer.
What you will do is install the printer using a USB connection, then re-run the setup software. Here there should be an option for USB to Wireless. This will be the easiest way to be sure that all the settings are correctly transferred over.
http://h10025.www1.hp.com/ewfrf/wc/softwareCategory?cc=us&lc=en&dlc=en&product=303770
You can find the software in the link above.
Let me know if this helps!

Help! Confusion over how to setup intel3945 wireless and rc.conf

Hi,
I'm very confused. I've already read through all the wikis and searched many forum posts. I can't get my wireless intel3945 to work on my dell vostro 1400.
Iwconfig says the wireless card is at wlan0 and dmesg | grep iwl says it has detected it. However, when I try a iwlist wlan0 scan it returns :
wlan0 Interface doesn't support scanning : Network is down
I think the problem is that I don't know how to setup rc.conf correctly or use the command line to test the wireless. Forum posts say many different things on how this is done.
These are the steps I have taken:
uninstalled the ipw3945 and ipw3945-ucode and ipw3945d.
installed iwlwifi and iwlwifi-3945-ucode
in my rc.conf modules, added iwl3945.
I'm not sure how to setup the networking section, this what I have now:
lo="lo 127.0.01"
eth0="dhcp"
wlan0="dhcp"
INTERFACES=(lo etho)
gateway="default gw 192.168.1.1"
ROUTES=(!gateway)
And in my dameons I have 'network'.
How can I scan for networks and connect to them on the commandline? I'd prefer not to use a gui tool because they never work and never tell me why they're not working.
Any help is greatly appreciated!
Cheers!
kilolima

iphitus wrote:
broch wrote:I have ipw3945 and iwl3945 working with wpa2 (or vpn)
(less complicatd than the above)
don't use netcfg2
Why?
no particular reason.
Simply when I configured wireless, netcfg2 wasn't available. Since then it (wireless) works, so not having any problems, I did not modify network setup. Next week or so I am going to install Arch on my daughter's laptop (per her request ) so I will try netcfg2.
So this is what I have for ipw3945 wpa2 or iwl3945 with wpa2
Below you will find a lot of words so read slowly but there is not much actual work
ipw3945 setup
kernel 2.6.23.x (Arch or vanilla)
or
kernel 2.6.24/2.6.24-gitX (patched with ipw3945 patch from gentoo -> compiling separate module for 2.6.24 may fail. if you want kernel patch I can post a link)
for default kernel install Arch packages for ipw3945, ipw3945d, ipw3945-ucode
or
if you want to compile modules, you will also need ieee80211 (first uninstall kernel's default, then install from sources otherwise ieee80211 from sources may refuse to install)
modify /etc/rc.conf
DAEMONS=(.... @ipw3945d @network ....)
that is all you don't need to add ipw3945 to MODULES=(.....)
because ipw3945d will automatically start ipw3945 module
do not list eth1 in network config section:
lo="lo 127.0.0.1"
eth0="dhcp"
INTERFACES=(eth0)
as you see, in my case only eth0 (wired) is listed and eth1 (wireless) is not listed
now you are done with basic network configuration for ipw3945, restart network/computer to bring up ipw3945d/ipw3945
check if modules are up and basic network is set:
#lsmod | grep ipw
#ifconfig -a
or
#iwconfig
if all is o.k. configure
WPA2:
configure router for wpa2
client: basically follow Arch wiki:
configure wpa_supplicant (installed already of course)
#wpa_passphrase your_ssid your_psk
keep terminal window open with created encrypted wpa passphrase and in the second terminal window edit /etc/wpa_supplicant.conf
ctrl_interface=/var/run/wpa_supplicant
network={
ssid="your_ssid"
scan_ssid=1
proto=WPA RSN
key_mgmt=WPA-PSK
pairwise=CCMP TKIP
group=CCMP TKIP
psk=whatever_output_from_wpa_passphrase
Above pairwise and group setup will depend on your router (network capabilities)
almost done:
run
#wpa_supplicant -Bw -Dwext -i eth1 -c/etc/wpa_supplicant.conf
the above assumes that your ipw3945 is set as eth1 (from iwconfig output)
to connect to the network I am using "wireless assistant" http://www.kde-apps.org/content/show.ph … tent=21832
that is all for ipw3945. You may automate network starting/connecting to wpa2 by writing simple script.
iwl3945
--kernel 2.6.23.x
install iwlwifi and iwlwifi-3945-ucode
--kernel 2.6.24.x
install only iwlwifi-3945-ucode as kernel has iwlwifi module incorporated
default iwlwifi does not support LED so I suggest to install something like knemo for kde to show active network icon. The latest iwlwifi does support LED but it is not yet incorporated into 2.6.24 vanilla kernel.
if you have kernel 2.6.23.x with external iwlwifi module
modify /etc/rc.conf
and add iwlwifi to
MODULES=(.....)
nothing else is required.
if you have kernel 2.6.24 with integrated iwlwifi module you don't have to edit /etc/rc.conf
As in the case of ipw3945, I do not list wireless interface (wlan0) in /etc/rc.conf
for kernel 2.6.23.x
load module/restart network or simply restart computer
check if module is up
#lsmod | grep iwl
#iwconfig
or
#ifconfig -a
WPA2
same wpa_supplicant.conf as above, so if you already have it no need for modifications.
start wpa2
#wpa_supplicant -Bw -Dwext -i wlan0 -c/etc/wpa_supplicant.conf
the only difference in the command is wireless interface: wlan0
connect to the network, again I am using "wireless assistant"
vpn
I am using cisco vpn. Client is provided by vpn host, cisco does not provide vpn client for individual download, but you can find it on line.
vpn host will provide pcf file for you
- install vpnclient
- copy your VPN profile (vpn.pcf) to the
/etc/CiscoSystemsVPNClient/Profiles
directory
-- start vpn client
/opt/cisco-vpnclient/bin/vpnclient connect vpn pcf_file_name
provide username and password and off you go
From my experience none of linux gui for vpn works reliably so you will have to resort to the command line.
That is all, a lot of writing, but actual ipw3945 and iwl3945 configuration is straightforward and very short.
Hopefully this will work for you.
forgot to add regarding vpnclient (cisco)
you will have to modify
/etc/init.d/vpnclient_init
line 38 and line 101
replace
/sbin/lsmod
with
/bin/lsmod
Last edited by broch (2008-02-07 15:55:45)

How to setup three SharePoint sites on one server?

Hello,
How to setup three SharePoint sites on one server? I have three sites like:
http://site1
http://site2
http://site3
And need to have them running up on one server. I recall some changes need to be done to the host file, but not sure. Can you advise on what to change?
Thanks,
Paul
Paul

you need to make entries in DNS to get this done.
check here:http://spshare.blogspot.com/2012/05/how-to-create-host-header-web.html
nice blog with step by step explanation:
http://thuansoldier.net/?p=1323
Please remember to mark your question as answered &Vote helpful,if this solves/helps your problem. ****************************************************************************************** Thanks -WS MCITP(SharePoint 2010, 2013) Blog: http://wscheema.com/blog

How to setup multiple base station under one network?

How to setup multiple base station under one network? I have 6 rooms but one airport base station makes really difficult to get good signal from every rooms. I wonder if I can setup multiple airport base stations talking to each other under the same network to build up the signal strength will help solve this problem. But, is it possible? How?

One route would be to utilize a "roaming" network. In a roaming network, you would connect multiple AirPort Extreme Base Stations (AEBS) to the same Ethernet. Of course, this would require that your home is already wired for Ethernet.

How to Setup SSL on Oracle Application Server 10g Release 2 (10.1..2)

Hi All,
Can anybody tell me How to setup the SSL on Oracle Application Server 10g Release 2 (10.1.2).
I have all the required documents like
1. Oracle Application Server Portal Server Configuration Guide.
2. Oracle Application Server Web Cache Configuration Guide.
3. Oracle Application Server SSO Administration Guide.
I tried to follow all this documents but still i am not able to set SSL for Oracle Portal Server.

The Portal Configuration Guide, available on OTN at http://www.oracle.com/technology/documentation/appserver1012.html does provide some very specific information on how to set up OracleAS Portal.
Section 6.3.2.1 Configuring SSL for OracleAS Portal describes various configurations, such as:
SSL to OracleAS Single Sign-On
SSL to OracleAS Web Cache
SSL Throughout OracleAS Portal
External SSL with Non-SSL Within Oracle Application Server
For larger enterprise configurations, you can refer to the Enterprise Deployment Guide.
Can you give a bit more background on what you are trying to set up? Which scenario, what sort of hardware, software versions, and so on.
Regards,
Pete

How to setup a static IP for a wireless printer

This problem has been ongoing for several versions of OS X and the last five printers I've had and I'm finally over messing with it. For some reson, when using a wireless printer with OS X this is a repetetive problem, and I think if I configured the printer to a static IP address instead of using DHCP, it might work better. At least once a week, if not more often, I'll print something and get the ubiquitous Dock error of "Printer is not connected". The printer is still in Preferences, but if I delete it, then it doesn't show up as it should for selection.
The only way to fix this is reboot, and then the printer shows up again in Preferences. I select it and all is well again...until a few days pass and the same thing happens again. Using an HP LaserJet P1102w, still a current model, but it doesn't matter which printer I use. I also have an Epson Artisan 725 and the same thing happens with it about once a week. Also, this happens from both my Mac and my wife's Mac, so it's not an issue with just my machine.
I've searched for documentation on how to setup a static IP address for a wireless printer with the Airport Extreme, but all I find are tutorials on how to do it with an ethernet hard-wired printer. Any help would be greatly appreciated.

You could set up your router to do manual assignment of IP address instead of using DHCP, but that is a PITA, because then you'd have to manually set up IP for all your devices.
If you have AirPOrt Extreme, you could do this:
In your Apple TV, go to the Settings >> About and write down the MAC address of your ATV
Start up the AiPort Admin Utility
Go to Network tab
click + in the DHCP reservations
Choose an IP you want for your ATV & Enter the MAC address
From now on, this IP address will be reserved to the MAC address and only your ATV will be able to get it, no other device will.
It is not a static IP in a true sense, but behaves just like one.
Works great for me...
If you don't have a AP Extreme, I'm sure other routers will allow you do reservations too.

How to setup Charms in a 2 tier landscape ?

Hi All,
We have a two tier landscape i.e only having development and production system so how to setup STMS and all other settings in this type of scenario.
Can we use Virtual system in STMS as a Quality system ? If yes then please guide us and tell me how to proceed as if we dont know how to add virtual system in SMSY in solman. Please provide us with a clear picture and give us detail documentation if possible.

Hi All,
Please tell me as per the SAP standard recommendation is it necessary to have a cycle like DEV->QUAL-PROD for Charms as we are not having any Quality system or Client here in our landscape.
Please suggest a way how to proceed in this case. Please help me out.

How to setup breakpoints in a vector space?

Hi,
How to setup breakpoints in a 2D vector space in NI 7344 and check for them using flex_read_breakpoint_status_rtn?
Thanks.

Hi,
Is Office Communicator something to do with the Word, Exel and Powerpoint Office Package ?
What sort of Screen Names or IDs do you use with that ?
If these are MSN/Live accounts names then it can be made to work for Text Chats but not Video or Audio Only chats
10:38 PM Friday; April 20, 2012
Please, if posting Logs, do not post any Log info after the line "Binary Images for iChat"
 iMac 2.5Ghz 5i 2011 (Lion 10.7.2)
 G4/1GhzDual MDD (Leopard 10.5.8)
 MacBookPro 2Gb (Snow Leopard 10.6.8)
 Mac OS X (10.6.8),
"Limit the Logs to the Bits above Binary Images."  No, Seriously

How to setup iChat in a office

How to setup iChat in a office that using Office Communicator as a IM ?

Hi,
Is Office Communicator something to do with the Word, Exel and Powerpoint Office Package ?
What sort of Screen Names or IDs do you use with that ?
If these are MSN/Live accounts names then it can be made to work for Text Chats but not Video or Audio Only chats
10:38 PM Friday; April 20, 2012
Please, if posting Logs, do not post any Log info after the line "Binary Images for iChat"
 iMac 2.5Ghz 5i 2011 (Lion 10.7.2)
 G4/1GhzDual MDD (Leopard 10.5.8)
 MacBookPro 2Gb (Snow Leopard 10.6.8)
 Mac OS X (10.6.8),
"Limit the Logs to the Bits above Binary Images."  No, Seriously

How to Setup Historical DSC Database on a standalone Server

Hey @all,
I am looking for documentation how to setup a standalone server for the DSC Module(Ver. 8) Historical Database.
My aim is to log all data to this server. The Server will be running Win2K.
Do I have to install the complete Labview 8 software and the DSC Module?
Does a walkthrough exist how to setup a DSC server?
Thx!
Carsten

After installing the runtime you should only have to reboot the computer in order to get the citadel service running. At the point, for citadel purposes, this machine will behave as though you had the DSC development system installed. The 8.0 runtime has no setup requirements...it should only need to be installed. Unlike previous versions, 8.0 requires you to build your application into an executable and the runtime should be invisible to you once you install it. If this is not the case, please post about it so it can be looked at.
If you have specific questions, please post them and I will either try and help you find the answers, get them posted, or answer them myself.
Regards,
Robert

How to setup the security based on roles in Organization.

Hi,
How to setup the security based on roles in Organization.
For example:Few users are Manager and a few user are Non Manager .Manager should have access to all work data including Non Manager and Non Manager should access based role.How to setup this? How OBI server identify the user role?
kindly let me know.
Regards.,
CHR

Hi,
You need to have Back End support to achieve this. In Back End you need to create two groups . You need to know what joins has to be made for which group (which is more important) and also make session variable for the userrole (with SQL supporting it). In the BMM layer, we need to put the security join conditions in the 'where clause'.
And make a common report. User loggin in with the respective userid will have userrole and joins assigned in the Back end. And they will be viewing the report according to their access.
Hope this will solve your problem.
Regards
MuRam

How to Setup JMS in Siebel Server

Hi
Currently we have a Requirement to work with queuing System from JMS Queuing
How to Setup the JMS Queuing from Siebel Point of view?
Does JMS Should be Installed in Siebel Server?
Plz Provide Inputs for How to Set up the JMS Queuing Mechanism and Setting up the Queues for Posting and Receiving the Messages from JMS Queues
Thanks & Regards
Rajendra Prasad

Update - it works ! At least I can connect to Mountain Lion (not server) from my iPhone using the VPN Server Configurator app.
Here's what I did :
1) download the app and install
2) setup using the help files on the web page : http://www.greenworldsoft.com/product-vpn-server-help.html
3) at the last stage you need to setup port forwardin on your router
4) under Airport Utility 6.0 you cannot setup ports 500 or 4500 due to BTTM conflicts but setup the other 2 ports (1723 TCP and 1701 UDP), update airport extreme
5) download Airport Utility 5.6 from here : download already extracted utility it is in it's extracted form as is necessary under Mtn Lion (thanks to NetUse Monitor for the download - great app by the way)
6) run 5.6 and setup port forwarding (Advanced-Port Mapping) for the other 2 ports (500 and 4500 UDP), update airport extreme
7) that's it, I was able to connect to the VPN from my iPhone !

How to setup WPA?

Similar Messages

Maybe you are looking for