How to share devices on an airport?

I have a wired network setup like here:
internet
router (192.168.1.1)
192.168.1.2 computer
192.168.1.3 computer
192.168.1.4 mac pro 10.0.1.2 --- wireless --- 10.0.1.1 airport --- speaker
The airport is configured for a stand-alone network - no internet sharing, guest wlan etc.
Now I would like to send audio from one of the other computers to the speaker.
When I set up a route to the 10.0.1 network via 192.168.1.4 AND enable forwarding on the mac, I can ping its 10.0.1.2 address. However, I can only ping the airport right from the mac, but not from the other computers. Which settings would I need to change to make this work?

The following are the basics for setting up the 802.11n AirPorts for port mapping/forwarding:
AEBSn - Port Mapping Setup
To setup port mapping on an 802.11n AirPort Extreme Base Station (AEBSn), either connect to the AEBSn's wireless network or temporarily connect directly, using an Ethernet cable, to one of the LAN port of the AEBSn, and then use the AirPort Utility, in Manual Setup, to make these settings:
1. Reserve a DHCP-provided IP address for the host device.
AirPort Utility > Select the AEBSn > Manual Setup > Internet > DHCP tab
On the DHCP tab, click the "+" (Add) button to enter DHCP Reservations.
Description: <enter the desired description of the host device>
Reserve address by: MAC Address
Click Continue.
MAC Address: <enter the MAC (what Apple calls Ethernet ID if you are using wired or AirPort ID if wireless) hardware address of the host computer>
IPv4 Address: <enter the desired IP address>
Click Done.
2. Setup Port Mapping on the AEBSn.
AirPort Utility > Select the AEBSn > Manual Setup >Advanced > Port Mapping tab
Click the "+" (Add) button
Service: <choose the appropriate service from the Service pop-up menu>
Public UDP Port(s): <enter the appropriate UDP port values>
Public TCP Port(s): <enter the appropriate TCP port values>
Private IP Address: <enter the IP address of the host server>
Private UDP Port(s): <enter the same as Public UDP Ports or your choice>
Private TCP Port(s): <enter the same as Public TCP Ports or your choice>
Click "Continue"

Similar Messages

How to share information from the airport to different users on macbook air

How do I access the information stored on our airport? It is connected to one user, and other users need the information that is on it. I've tried to access it and it says I need a password. How is that setup?

The AirPort is a wireless Internet router. I am assuming that the information you are referring to is data stored on a hard drive attached to either an AirPort Extreme or the internal hard drive of a Time Capsule. Is either of these correct?
If so, please check out the following Apple Support article on how to access these drives from either a Mac or PC.

How to share external USB drive connected to airport time capsule

I have a 4TB Seagate USB Hard Drive connected to my Airport Time Capsule. The Time Capsule connected to a newer iMac running Maverick.
I use the Time Capsule for Time Machines Backups and as a Router, as it was designed for.
I want to use the external Seagate drive to share content with other devices (Mac, IOS, Windows) on my home network
Problem: I cannot figure out how to SHARE the external Seagate drive so that any other devices can see it.
Steps tried: Go to System Preferences, Sharing, and I am unable to add this Seagate drive to list of sharable objects. It is grayed out.

the drive is formatted as AppleShare. Is that a potential problem?
No, that is the correct setting if you want to share out the drive.
Finally, when I run Disk Utility I don't see the Seagate drive (nor the Time Capsule) at all.
Remember that the Time Capsule is a network drive. Any other drive connected to the USB port on the Time Capsule is also a network drive.
Disk Utility cannot be used on a network drive. It only works on a drive that is directly attached to a Mac. If you need to partition the USB drive or something similar, you will need to connect it directly to your Mac for the operation.
Otherwise, everything looks correct in AirPort Utility.

How to share account with multiple devices?

3 kids with 3 devices - an iPod Touch and two iPads Mini - family shares one account with Apple/iTunes and one library on our family PC. They use FACETIME and MESSAGES with their friends, and they all see each others messages and conversations. How do I fix this? Is there a setting or a way to create sub-accounts off the family account so they can still share the main library for music and video OR do I have to create separate Apple/iTunes accounts for each kid? Is there a setting on their devices that can help? Any help is greatly appreciated. I'm not even sure the right question to ask...

How to use multiple iPods, iPads, or iPhones with one computer
http://support.apple.com/kb/HT1495
How to Share a Family iPad
http://www.macworld.com/article/1163347/how_to_share_a_family_ipad.html
Using iPhone, iPad, or iPod with multiple computers
http://support.apple.com/kb/ht1202
iOS & iCloud Tips: Sharing an Apple ID With Your Family
http://www.macstories.net/stories/ios-5-icloud-tips-sharing-an-apple-id-with-you r-family/
How To Best Use and Share Apple IDs across iPhones, iPads and iPods
http://www.nerdsonsite.com/blog/2012/06/07/help-im-appleid-confused/
 Cheers, Tom

How to share 3G with other Apple devices

Hi, I just updated my iPad to iOS 4.3 and I can't find how to share my Internet connection with other devices.
Could you help me?
Thanks,

You can't with the iPad, you need an iPhone 4 to use the HotSpot feature.

How to share an airport internet connection with XP thru a crossover cable

Any help appreciated - My iMac is connected to the internet and home network through airport. I would like to connect an XP machine to the iMac through ethernet with a crossover cable. I'd then like to be able to share the iMac's internet and network connection with the XP and file share between computers.
How should I configure the machines? I can get them to share files (with a manual IP address) but even though "Internet Sharing" is clicked on the iMac the XP does not connect to the internet.
iMac is running 10.5.6
thanks for any help!

Yes, I do have "internet sharing" turned on. It is set to share the connection from Airport to computers using Ethernet. But there is no internet on the PC. Should they both be set for DHCP? (they are)

How do I re-install an airport device on a mac pro

How do I re-install an airport device on a imac. The machine says no hardware - it lies:-)
Whats happened to theis how do I fix it

First thing to try would be to reset the parameter RAM. Second, reset the System Management Controller.
Best of luck.

How to share event in calendar to other device

Hello everybody. I am having problem with my calendar sharing. Can everybody show me how to share my event in calendar in my iphone to my girlfriend iphone. I want she can see my event in her iphone. My device's ios version in 5.1.1 and my girlfriend device is ios 8. Thank you very much.

gooddog wrote:
I want the calendar app to mark days with appointments so that I can see them in the Month view.
Days with appointments will be marked with a dot in month view. Tapping the icon that looks like a box with three lines underit will show you events for the selected day in month view.
Also, I don't want to have to select mail messages individually for deletion. How can I do this more quickly (besides tapping faster)?
You can't.

How many wireless devices can be connected at once to an airport extreme?

How many wireless devices can be connected to an airport extreem at one time? I have 4 iphones and 2 ipads, a goolge chrome and 4 wired devices.

Any AirPort Extreme produced since 2008 will support up to 50 wireless devices and 150+ wired devices simultaneously, so this should accommodate most users in most homes.

How can I see all devices using my airport express?

Is there any way to see all devices using my airport express for wifi connection?

Open Macinotsh HD > Applications > Utilities > AriPort Utility
Select the AirPort Express and click on Manual Setup
Click directly on the word Wireless Clients about 2/3 of the way down the page to see the MAC Address of each connected device along with the IP address that has been assigned.
You will need to do a bit of experimenation to be able to identify which device is which based on the MAC address.
Disconnect all but one device and note the MAC address. You now know that product that is.
Turn that one off and connect another. You now know what that device is, etc.
If you have 4 wireless devices...and you see 5 connected devices.....you may have an unwanted guest.

How to share your itunes library with another person

how can two people have all the same stuff on their ipods/iphones? we have both bought different things but dont know how to share them

Hey jimyam,
Thanks for the question. If you wish to access your music library from multiple devices, anywhere, It sounds like iTunes Match may be the right service for you:
Apple - iTunes - Match
http://www.apple.com/itunes/itunes-match/
With iTunes Match, all your music can be stored in iCloud — even songs you’ve imported from CDs. You can access your music from all your devices and listen to your entire library wherever you are. And you'll also be able to listen to iTunes Radio without ads.
iTunes Store: Subscribing to iTunes Match
http://support.apple.com/kb/HT4914
Thanks,
Matt M.

How do I remove an unwanted Airport Express from my network?

I have been using a Time Capsule for several years. I am having trouble backing up to my Time Capsule. I have discovered an unknown Airport Express in my network. I've changed networks, added passwords to the network, etc. How do I remove this unwanted Airport Express from my network? I think he is wreaking havoc with my system!! Help...

Maybe this is an issue I should consult my ISP about??
No question about that. If you can "see" Travis's device, then he can likely "see" your Time Capsule.
I'm just concerned that whomever the APExpress belongs to could be changing settings on my computer or Time Capsule that would cause the issues with me not being able to backup.
Make sure that you have a Time Capsule base station password. Unless a user has that password, they might be able to "see" your Time Capsule, but they cannot access any of the data on the Time Capsule or change the settings.
Open AirPort Utility, click on the Time Capsule and click Manual Setup
Then, click the Time Capsule tab below the icons to see the device name and password for your device. Make sure that you have entered the password and confirmed. Click Update if you have made any changes.
The message I get is "The backup was not performed because an error occurred while copying files to the backup disk. The problem may be temporary. Try again later to back up. If the problem persists, use Disk Utility to repair your backup disk."
I am not sure what this error means, because I cannot duplicate it here to test.
If it were me, I would try this "fix".
http://pondini.org/TM/A5b.html

How to set up 6th Generation AirPort Extreme to cable modem as a wireless router and then connect my 3rd Generation Time Capsule to AirPort Extreme as a wireless extender?

What is the best way to set up my 6th Generation AirPort Extreme (A1521) to my cable modem as a wireless router and then connect my 3rd Generation Time Capsule (A1355) to my AirPort Extreme as a wireless extender? I live in a small 1 story house and I currently have the Airport Extreme connected to my cable modem in the living room and the Time Capsule plugged into the wall in my bedroom. I am able to wirelessly connect to the internet using the AirPort Extreme as my router and I can also do wireless back ups to my Time Capsule. My problem is that my connection seems to be really slow! My 1TB Time Capsule back up is only half way complete and it has been 3 days! My computer has been backing up all day and night for almost 72 hours and its still not even 75% complete. I have backed up to this Time Capsule in the past and it never took this long. I am thinking that when I set up my AirPort Extreme and Time Capsule using AirPort Utility I must have set it up incorrectly or something.
How do I set up my Airport Extreme and Time Capsule for the fastest possible internet speed and back up speed?
Thank you,

AirPort Utility 5.6 works with AirPort Extreme 802.11g base stations.
It works with N version airports.
It will also show details of the AC model but cannot be used for the setup.. mostly.
I purposely got the new 6th Gen Airport Extreme so my internet connection would be a lot faster!
Your network will be much faster when you have AC client directly connected to the AE. Older client will go no faster.. but what is worse.. extend wireless is mixing new and old wireless standards.. guess what one wins.. OLD.. So when you extend wireless.. you have no improvement whatsoever. This whole post is about extending wireless.. so you cannot extend to older equipment and do any better.. maybe slightly better signal although from your comments that isn't happening either.
I would rather not have to use an ethernet at all with the TC and I don't know EOP adapters are!
If you do not use ethernet then you are going to be forced to accept slow speed.
EOP (ethernet over power). Also called homeplug in the US.
http://en.wikipedia.org/wiki/HomePlug
Provides a method of networking over power cabling that already exists in your house.
So what your saying is for the fastest internet speed and back up speed possible I should keep my Airport Extreme plugged into my Modem and keep my TC set up as a wireless extender? Then when I want to do back ups I should plug an ethernet cable from my TC to my MacBook Pro?
To spell this out.
A wireless link to an extended device will go very slowly.. if it is not direct.
So lets say you have a laptop sitting in the lounge.. Your connection goes.. Laptop- - - - - AE- - - - -TC.
That means two wireless links.. wireless has this nasty half duplex and single channel nature.. it can send or receive (Tx or Rx) but not at the same time.
Ethernet by contrast does both at once. It is full duplex.
Wireless can talk to one client at a time.. so if there are multiple items using wireless lets say 4 devices.. then your computer gets a 25% time slice. Since wireless cannot handle multiple simultaneous connections.
Ethernet by contrast can connect multiple computers to multiple destinations at the same time.. all transmitting and receiving at full speed.
When you put all this together.. there are a couple of rules for fast connection.
1. Use ethernet at all times. Where you cannot use ethernet use anything but wireless.. eg EOP (homeplug) at least to try and get rid of wireless.
2. Where you must use wireless use it sparingly and make sure it is never more than one hop.. ie never have an extend wireless (repeater is more usual term). Repeater will cause instant slowdown of 50% and maybe up to 75% just because it is so inefficient.
3. Fastest wireless is 5ghz but it has very short range.. you need to be up close and personal to get it working.
Apple routers however unless you do manual setup I suggest are set to connect to best signal strength not best speed. It will therefore use 2.4ghz at 25% less speed than 5ghz because it is 1db better signal.. this madness means you need to setup manually for the best setup.

How do I set up my Airport Extreme to best use multiplayer games locally

How do I set up my Airport Extreme to best use multiplayer games with my family. Everyone is located in the same house and uses the same router.
I have tried a few games but have not successfully connected 2 players

That is a weird question, as your GAMES could be interpreted a hundred different ways. Are we talking about third party devices here or what?

I'd like to alter my Airport Extreme/Airport Express wireless network so that the 3 Expresses connect to the Extreme via Ethernet. I've been told this will create a more stable wifi signal. How do I configure this using Airport Utility? Thanks.

I currently have an Airport Extreme Base Station connected to my DSL router by Ethernet. Because I have a long, sprawling home, I have 3 Airport Expresses configured to "Extend the Wireless Network" I've established. Because of my home environment--thick walls encompassaing wire mesh, sprawling rooms, etc., it is hard to maintain a continuously-strong, stable WiFi signal. I've been told that I can create a much more stable network by connecting the Express units to the AEBS via Ethernet cable. Since my home is already wired for Ethernet, I'm considering making this change. If I proceed to establish the Ethernet connections, how do I then set up Airport Utility to accomodate this switch from a Wireless-based WiFi network to an Ethernet-based WiFi network?
Thanks in advance for any help.
Phyllis

I don't see anyplace in the Utility to designate HOW the Express units are connected, only how they relate on the network to the Extreme,
As I mentioned in the previous post, when you click the Internet icon in AirPort Utility:
Connect Using = Ethernet (This tells each Express to connect to the Extreme using the ethernet connection)
Connection Sharing = Off (Bridge Mode) (This setting allows your AirPort Extreme to function as the "main" router on the network, as it must for the setup to work correctly.
You do not need to configure anything differently on the AirPort Extreme (as long as it is working correctly now) to connect the AirPort Express devices.
The only other question I have is the following: I'm currently already using one of the Ethernet ports on the back of the Extreme-- for my husband's iMac. I really don't think he gains much in performance over how the iMac would run through wifi, so I could disconnect the iMac. If you think the iMac would do better to stay on the Ethernet connection, should I use a switch/splitter to add an extra connection?
Since each AirPort Express must connect using ethernet, you will need to use the 3 LAN <-> ports on the AirPort Extreme for the AirPort Express devices.
I would suggest that you try connecting the iMac using wireless to see if that will work. If the wireless connection is not satisfactory, then you can add a 5 port ethernet switch to one of the LAN ports on the Extreme and then plug all the devices connecting using ethernet....the iMac and the 3 AirPort Express devices...into the remaining 4 ports on the switch. That will leave you with 2 open ports on the AirPort Extreme for any future devices that may need to connect.
When you test out the system, here is a trick to find out which device your computer is actually connecting to at any given time as it "roams" around the house.
When you have AirPort Utility open to configure each AirPort Express, jot down the AirPort ID for each Express. You can do the same for the AirPort Extreme.
As you move around with your laptop, hold down the option key on your Mac keyboard while you click on the fan shaped AirPort icon at the top of the screen. Look for the BSSID. That is the AirPort ID of the device that the laptop is connected to at that time. it should also be the ID of the closest AirPort Express (or AirPort Extreme if the laptop is close to the Extreme at the time).
Let us know how things are working when everything is up and running.

How to share devices on an airport?

Similar Messages

Maybe you are looking for