How to snoop traffic on PGW 2200 with Wireshark

How to snoop traffic between PGW 2200 & MGX 8880 with Wireshark?

I hope to have understood correctly your question.
1) enable the snoop on PGW using ./snoop_scrip in /opt/snoop/ path
2) collect the trace of the call and so stop the snoop usinf CTRL C
3) open wireshark
4) drag and drop the files generated from the snoop in wireshark
5) wireshark will ask to merge the file
P.S. PGW uses RUDP to communicate with the media gateway. Set the wireshark RUDP port (in Edit - Preferences - Protocols menu) according to PGW configuration.
Regards.

Similar Messages

Cisco PGW 2200 is part of Cisco HCS

Hi all,
I was supprized that PGW 2200 is part of HCS suite while there is a EoS/EoS announcement for PGW
http://www.cisco.com/en/US/prod/collateral/voicesw/ps6788/vcallcon/ps8362/product_data_sheet0900aecd80670040_ps556_Products_Data_Sheet.html
http://www.cisco.com/en/US/prod/collateral/voicesw/ps6788/vcallcon/ps2027/end_of_life_notice_c51-676990.html
How does that match?
Kind regards
Peter

Hi,
In HCS, PGW interfaces with CUBE(SP) and central PSTN break-out trunks (SIP and SS7). CUBE(SP) as SIP proxy controls signaling from and to CUCM leaf clusters to PGW, and acts as a media anchoring device to control media flow between enterprises.
PGW is used as an aggregation layer for routing the calls to the PSTN and serves as a central break out (CBO) for HCS 8.6.2. PGW is installed on the Cisco Unified Computing System (UCS) platform and is deployed in active/standby mode.
At the bottom of the bullitin it reads:
"Cisco HUCS/HCS customers are requested to work with the Cisco account team for support and migration options."
Thanks

How to print on HP LaserJet 2200 over Ethernet?

Hi,
I did an upgrade to Snow Leopard and would like to print on a HP LaserJet 2200 over Ethernet. OS X and the HP printer drivers are up to date now.
The printer has been cold reset and on the configuration print out there's the IP address 0.0.0.0
Now my question is how to get this printer to work with Snow Leopard over Ethernet? I did not find a tutorial how to assign an IP address to the printer first so I got stuck.
Could you give me a hint where I should start with the configuration first?

OK, now the printer works
I reset the router and checked if DHPC is running.
I reset the printer (hold down the GO button, turn the printer on and continue to hold the GO button for five to ten seconds).
Checked at router that the printer is visible as network device.
At the router I assigned a fixed IP address to the printer.
At OS X System Preferences > Printer I added a new printer with "HP Jetdirect - Socket", the fixed IP address and the correct printer driver "HP LaserJet 2200".
Now the printer has been recognized well by the system (Tray 3, Duplex and printer RAM) and printing works.
THANKS.

How to route traffic across subnets when one NIC is a hyper-V virtual switch?

Having a bit of a problem with a hyper-V environment which does not seem to route network traffic on two different subnets between each other.
If it were a purely physical server with two NICs and a gateway set traffic would automatically be forwarded between the two different subnets.
However when one of those NICs is a hyper-V virtual switch this simple routing no-longer seems to work and no traffic gets forwarded between subnets?
Situation is:
Hyper-V server with two NICs
NIC 1 = 192.168.0/24 - main Internal company network.
NIC 2 (hyper-V virtual switch.) = 192.168.1/24 - connects to ADSL internet router
Virtualized Domain Controller.
One or two virtualiszed NICs as necessary
How then does traffic get routed between these two subnets? If RRAS has to be configured to do this where is the best place to do it, on the hyper-V host or on the virtualized domain controller?
Thanks,

Hi ,
You can create an internal virtual switch and configure an IP for it (I assume it is 192.168.1.2/24) .
After you enable RRAS in hyper-v host there will be two gateways for different subnets .
" NIC 2 (hyper-V virtual switch.) = 192.168.1/24 - connects to ADSL internet router "
The problem is here ,if these VMs need to access internet .
So , these VMs can not configure their gateway same as the IP of internal virtual switch , you may set VM's gateway as the ADSL internet router's IP meanwhile add a static route entry for every VM .
Please refer to the Syntax :
route add -p 192.168.0.0 mask 255.255.255.0 192.168.1.2
Hope this helps
Best Regards
Elton Ji
We
are trying to better understand customer views on social support experience, so your participation in this
interview project would be greatly appreciated if you have time.
Thanks for helping make community forums a great place.

Update to kichat: FAQ 2 - How to get my router to work with iChat?

kichat: FAQ 2 - How to get my router to work with iChat? December 2008 version 3
(Note to Hosts. to be removed on acceptance. Please use this to replace http://discussions.apple.com/thread.jspa?threadID=121775 )
Getting your router started with iChat.
Appropriate for using iChatAV 2 upwards. Edits have been made for iChat 4
Glossary for this FAQ
Routers: Any configurable device that sits between your computer and the internet link you have. This includes Modems that Route as well as "routers"
Routers seem to fall into two categories
Those that work straight from the box. See Apple Article HT1787
NOTE :This Article has not been updated in content since Jan 04 Only being changed to an Article from the Previous Doc listing
Even then some list that they need tweaks.
and those that do not.
This post will deal with what you may need to look at.
First off make sure your device is acting as a DHCP server. (if you are already on the internet you may not have to bother with this.)
Check in the Tiger System Preferences > Network Preference Pane, in the "Built in Ethernet" option from the "Show" drop down list.
In Leopard the Networks are listed on the left with icons. The Airport Option will need you to access the Advance Button for the Next bit.
Make sure the TCP/IP tab is the 'front' one. You should be able to see Configure IPv4 and it most likely reads Using DCHP. Make a note of your IP address. It will start 10.xxx.xxx.xxx or 192.168.xxx.xxx (the 'x' s will stand for any number between 1 and 255). The range 172.16.xxx.xxx is also a possible value at this point. Rarely used, but it is part of the RFC for Address Allocation for Private Internets.
Your router is most likely to be configurable from your browser. You will need to find the IP address to type into the browser from any Readme or PDF files that came on the install disk or visit the makers website and download a manual.
The Port Forward.com site lists many devices and clicking on one will take you to a list of Applications. This iChat will open an page that will start by telling you the defaults to access the device
Opening or Allowing ports. Several Methods not all devices have all of them.
DMZ (Demilitarised Zone)
This is a less secure setting that basically opens all ports and points the incoming data to your computer. (not helpful if you have more than one computer on your LAN). It can be considered as an extreme form of Port Forwarding
Port Forwarding (also Virtual Server or Pin Holes)
These settings are usually found in an Advanced setting.
You may need to set an incoming IP address (Usually 0.0.0.0 to any outside server), a port that data will arrive on, the Inside computer's IP address (your computer) and the port it will deal with the data on and the protocol it will use.
See this pic for an example of the description above.
In this example shows that on some Port AND Protocols need to be listed.
iChat uses TCP and UDP so some devices will need the ports listed one by one and some settings done twice, once for each protocol. The example above has a "Both" setting
See Apple Article HT1507 Previously Doc 93208 for more information. This is the Tiger iChat 3 list. The same ports are needed for Leopard except for these changes
My Note 2:
On the first link Note 1 under tables in that link would be better if it read:
" 1. All iChat AV traffic is UDP -
except for ports 5190 and 5298, which need to be open for both TCP as well;
and 5220, 5222, which need to be open for TCP only. "
Note 2
GoggleTalk needs port 5223 on TCP. Also note the Server name for iChat 3 set ups
UPnP Universal Plug n Play.
This is a simple Plug and Play type of setting. iChat can find it's own way through a router if the device has this capability.
By Not doing Port Forwarding, Triggering or DMZ and enabling UPnP the application is allowed to control the modem and the ports that are open.
They close after the application has finished with them on a timed basis.
On some devices the number of "hops" (how far away the UPnP can be "seen") can be reduced from a default of 4)
Trigger Ports
Some devices offer a security measure that works by a first or trigger port receiving a data packet and then opening further ports when accepted.
The first port for incoming Video or Audio invites is port 5678.
Pre iChat 4
When you click on the invite window the process moves in to port 5060 (so these will need to be opened by the trigger port) for negotiating the final group of ports from the group of 20 (16384-16403 These will need to open when the trigger says so as well). Therefore port 5678 triggers ports 5678, 5060, 16384-16403. All on UDP. Port 5190 neeeds to trigger port 5190 for both TCP and UDP.
See this variation where only the ports listed above are completed.
The other single ports need to be set one by one in addition. (5220,5222, 5223 5297, 5298, 5353)Replace
iChat 4
The port used in IChat 4 is port 16402 instead of port 5060. The group of 20 ports is reduced to 10 (16393-16402). This is because all the In and Out Audio and Video data is on one port. Other that than the settings are the same.
At this time there is no Info on the ports the Screen Sharing in iChat 4 uses.
Wireless
Here you will have to read around but this Apple Article TA25949 Previously Doc 58514 might be a good starting place.
Essentially whether you are wireless or Ethernet to your routing device makes very little difference to the way you do things.
Your computer will get two IPs from a DHCP server if you are connected by both methods. (iChat does not like this)
Multiple devices
Make sure only one is acting as a DHCP server. Make sure wireless devices are bridged properly.
Further Help
I have found that this site (ADSLGuide) to be helpful.
It is British based but I have linked you to the Apple Related Discussions Forum.
Eliminating Problems on my Personal web pages.
The ports and their function within iChat. (my personal Web pages again)
This is not a step by step approach. You will have to read around the information about your device.
Collected FAQs and Expansions: Index Page Based on FAQs here by EZ Jim and myself
Also http://www.portforward.com/routers.htm for instructions with Pics on Port Forwarding and access info as mentioned earlier.
Click on your device.
Select iChat on the next page.
Follow the info on the next.
This site is godd for finding out the Default IP to use in a web browser and the default User ID and Passwords needed to do so.
Gives you a chance to look at at pics to give clues to where some of these other things are.
With thanks to Macmuse for comment on the Original (Aug 23rd 2004)
and to EZ Jim for his work on iSights on my web pages.
I may receive some form of compensation, financial or otherwise, from my recommendation or link.
9:51 PM Saturday; December 6, 2008

kichat: FAQ 2 - How to get my router to work with iChat? December 2008 version 3
(Note to Hosts. to be removed on acceptance. Please use this to replace http://discussions.apple.com/thread.jspa?threadID=121775 )
Getting your router started with iChat.
Appropriate for using iChatAV 2 upwards. Edits have been made for iChat 4
Glossary for this FAQ
Routers: Any configurable device that sits between your computer and the internet link you have. This includes Modems that Route as well as "routers"
Routers seem to fall into two categories
Those that work straight from the box. See Apple Article HT1787
NOTE :This Article has not been updated in content since Jan 04 Only being changed to an Article from the Previous Doc listing
Even then some list that they need tweaks.
and those that do not.
This post will deal with what you may need to look at.
First off make sure your device is acting as a DHCP server. (if you are already on the internet you may not have to bother with this.)
Check in the Tiger System Preferences > Network Preference Pane, in the "Built in Ethernet" option from the "Show" drop down list.
In Leopard the Networks are listed on the left with icons. The Airport Option will need you to access the Advance Button for the Next bit.
Make sure the TCP/IP tab is the 'front' one. You should be able to see Configure IPv4 and it most likely reads Using DCHP. Make a note of your IP address. It will start 10.xxx.xxx.xxx or 192.168.xxx.xxx (the 'x' s will stand for any number between 1 and 255). The range 172.16.xxx.xxx is also a possible value at this point. Rarely used, but it is part of the RFC for Address Allocation for Private Internets.
Your router is most likely to be configurable from your browser. You will need to find the IP address to type into the browser from any Readme or PDF files that came on the install disk or visit the makers website and download a manual.
The Port Forward.com site lists many devices and clicking on one will take you to a list of Applications. This iChat will open an page that will start by telling you the defaults to access the device
Opening or Allowing ports. Several Methods not all devices have all of them.
DMZ (Demilitarised Zone)
This is a less secure setting that basically opens all ports and points the incoming data to your computer. (not helpful if you have more than one computer on your LAN). It can be considered as an extreme form of Port Forwarding
Port Forwarding (also Virtual Server or Pin Holes)
These settings are usually found in an Advanced setting.
You may need to set an incoming IP address (Usually 0.0.0.0 to any outside server), a port that data will arrive on, the Inside computer's IP address (your computer) and the port it will deal with the data on and the protocol it will use.
See this pic for an example of the description above.
In this example shows that on some Port AND Protocols need to be listed.
iChat uses TCP and UDP so some devices will need the ports listed one by one and some settings done twice, once for each protocol. The example above has a "Both" setting
See Apple Article HT1507 Previously Doc 93208 for more information. This is the Tiger iChat 3 list. The same ports are needed for Leopard except for these changes
My Note 2:
On the first link Note 1 under tables in that link would be better if it read:
" 1. All iChat AV traffic is UDP -
except for ports 5190 and 5298, which need to be open for both TCP as well;
and 5220, 5222, which need to be open for TCP only. "
Note 2
GoggleTalk needs port 5223 on TCP. Also note the Server name for iChat 3 set ups
UPnP Universal Plug n Play.
This is a simple Plug and Play type of setting. iChat can find it's own way through a router if the device has this capability.
By Not doing Port Forwarding, Triggering or DMZ and enabling UPnP the application is allowed to control the modem and the ports that are open.
They close after the application has finished with them on a timed basis.
On some devices the number of "hops" (how far away the UPnP can be "seen") can be reduced from a default of 4)
Trigger Ports
Some devices offer a security measure that works by a first or trigger port receiving a data packet and then opening further ports when accepted.
The first port for incoming Video or Audio invites is port 5678.
Pre iChat 4
When you click on the invite window the process moves in to port 5060 (so these will need to be opened by the trigger port) for negotiating the final group of ports from the group of 20 (16384-16403 These will need to open when the trigger says so as well). Therefore port 5678 triggers ports 5678, 5060, 16384-16403. All on UDP. Port 5190 neeeds to trigger port 5190 for both TCP and UDP.
See this variation where only the ports listed above are completed.
The other single ports need to be set one by one in addition. (5220,5222, 5223 5297, 5298, 5353)Replace
iChat 4
The port used in IChat 4 is port 16402 instead of port 5060. The group of 20 ports is reduced to 10 (16393-16402). This is because all the In and Out Audio and Video data is on one port. Other that than the settings are the same.
At this time there is no Info on the ports the Screen Sharing in iChat 4 uses.
Wireless
Here you will have to read around but this Apple Article TA25949 Previously Doc 58514 might be a good starting place.
Essentially whether you are wireless or Ethernet to your routing device makes very little difference to the way you do things.
Your computer will get two IPs from a DHCP server if you are connected by both methods. (iChat does not like this)
Multiple devices
Make sure only one is acting as a DHCP server. Make sure wireless devices are bridged properly.
Further Help
I have found that this site (ADSLGuide) to be helpful.
It is British based but I have linked you to the Apple Related Discussions Forum.
Eliminating Problems on my Personal web pages.
The ports and their function within iChat. (my personal Web pages again)
This is not a step by step approach. You will have to read around the information about your device.
Collected FAQs and Expansions: Index Page Based on FAQs here by EZ Jim and myself
Also http://www.portforward.com/routers.htm for instructions with Pics on Port Forwarding and access info as mentioned earlier.
Click on your device.
Select iChat on the next page.
Follow the info on the next.
This site is godd for finding out the Default IP to use in a web browser and the default User ID and Passwords needed to do so.
Gives you a chance to look at at pics to give clues to where some of these other things are.
With thanks to Macmuse for comment on the Original (Aug 23rd 2004)
and to EZ Jim for his work on iSights on my web pages.
I may receive some form of compensation, financial or otherwise, from my recommendation or link.
9:51 PM Saturday; December 6, 2008

How to manage traffic of livestreams or youtube

Hi all,
at the moment we are discussing about how to control or limit traffic used by livestreams. At the moment there are many web pages with livestreams of the olympic winter games and customers facing very high traffic by hd videostreams.
So we are now thinking about managing this videostreams by implementing some policies on the proxies.
And we alternatively think about how to restrict traffic of videostreams or youtube video using asa.
Did not find anything in the knowledgebase. Do you have any hints how to manage this?
thank you in advance and best regards
Vincent

Just go trough Manage application and Modify application and use reindex and full process.
This normally should fix your issue.
Regards
Sorin Radulescu

GSM codec in MGCP controlled Gateway from PGW 2200

Hi everybody.
Currently we are performing a test using PGW 2200 to integrate a SIP server with PSTN. We control an AS5300 mediagateway through MGCP version 1.0.
I would like to know if it is possible that the SIP User Agents use GSM to encode the voice calls, which are established against the MGCP controlled MediaGateway. I have tried the whole steps mentioned to setup the codec selection within PGW with no success. (I followed the steps from Media Gateway Controller Dial Plan Guide).
Thanks in advance for all your help and attention.

GSM is not supported on Cisco ip phones

I lost my macbook pro and i just got a new one. how can i retrieve the pictures taken with photo booth(old laptop) to my new laptop?

i lost my macbook pro and i just got a new one. how can i retrieve the pictures taken with photo booth(old laptop) to my new laptop?

Well if you don't have the laptop to get the storage drive out of it, and you don't have any previous backups how do you expect to get the photo's?
PhotoBooth is just a program, it stores the files on the computers storage drive, if the computer is lost so are your photo's.
There is nothing you can do to delete or retrieve them using your new computer unless you stored them online someplace.
DId you save them online? iDisk or something else?
I don't use such services because my data is mine and not theirs to snoop through, so if your looking for that sort of help I can't assist you any.

How do I use Edge Web Fonts with Muse?

How do I use Edge Web Fonts with Muse - is it an update to load, a stand alone, how does it interface with Muse? I've updated to CC but have no info on this.

Hello,
Is there a reason why you want to use Edge Web Fonts with Adobe Muse?
Assuming you wish to improve typography of your web pages, you should know that Muse is fully integrated with Typekit. This allows you to access and apply over 500 web fonts from within Muse. Here's how you do it:
Select a text component within Muse, and click the Text drop-down.
Select Add Web Fonts option, to pop-open the Add Web Fonts dialog.
Browse and apply fonts per your design needs.
Muse also allows you to create paragraph styles that you can save and apply to chunks of text, a la InDesign. Watch this video for more information: http://tv.adobe.com/watch/muse-feature-tour/using-typekit-with-adobe-muse/
Also take a look at these help files to see if they help you:
http://helpx.adobe.com/muse/tutorials/typography-muse-part-1.html
http://helpx.adobe.com/muse/tutorials/typography-muse-part-2.html
http://helpx.adobe.com/muse/tutorials/typography-muse-part-3.html
Hope this helps!
Regards,
Suhas Yogin

How do I use Qt and OpenGL with Visual Studio

Hi! I mainly want to program in C++ and I want to use Qt and OpenGL with Visual Studio.
I am currently revising C++ and later on i am going to start reading Qt and OpenGL. I have a background of
Embedded firmware design(C and Assembly).
The Visual Studio Version I have is 2013 ultimate. How do I use Qt and OpenGL with Visual Studio?
Thanks
Alexandros

Hi ClassicalGuitar,
The forum supports VS setup and installation. And your issue is not about the forum. I will move the thread to off-topic forum. Thanks for your understanding.
Regards,
We are trying to better understand customer views on social support experience, so your participation in this interview project would be greatly appreciated if you have time. Thanks for helping make community forums a great place.
Click HERE to participate the survey.

How do i use my mac book with my HP 6510 e all in one series printer

how do i use my mac book with HP photosmart 6510 e all in one series

Hello Marilynatsea,
Thanks for using Apple Support Communities.
To learn more about printing in OS X on your Mac, and how to add a printer, take a look at the article linked to below.
Mac Basics: Printing in OS X - Apple Support
Cheers,
Alex H.

How do I use my gigaware webcam with my mac?

How do I use my gigaware webcam with my mac? I just bought this webcam on amazon http://www.amazon.com/gp/product/B00IJE0ISS/ref=oh_aui_detailpage_o07_s00?ie=UTF 8&psc=1 and I want to use it with my mac. Is there an adapter or any software to make it compatible? Thanks.

Your amazon link states, in part, that this webcam is:
Compatible with Microsoft Windows 7,Vista, XP, 2000
Use a Mac OS X Compatible Webcam like one of those shown in the linked article instead.
For best compatibility and security, also update your OS X Mavericks (10.9.2) to the current OS X version by restarting Mac and then downloading and installing OS X Mavericks 10.9.4 Update (Combo).

How do I use a foot pedal with my mac?

how do I use a foot pedal with my mac to use on YouTube?

Can you be more specific? What kind of foot pedal? What is the foot pedal used for?

How do i use a new computer with my ipod?

how do i use a new computer with my ipod?

See this apple support communities user tip…
Syncing to a "New" Computer or replacing a "crashed" Hard Drive

How do I use cell number associated with iPad 2 3G

How do I use cell number associated with iPad 2 3G

For Messages you can can use your email address, the iPad doesn't have a phone number that you can use.

How to snoop traffic on PGW 2200 with Wireshark

Similar Messages

Maybe you are looking for