How to turn off red LED when have a new voice mail?
How to turn off red LED when have a new voice mail?
My SPA303 VOIP Phone
Thanks
You must disable message waiting indication (MWI) on your platform.
Regards.
Similar Messages
-
How to turn off service led in a SF 6900
Hello
I have a SF6900 (the big server) and the service yellow light on top of the rack is on.
I can see it on with showplatform on the SC. There are no HW faults in this server. Does anyone know how to turn of this led?
I copied below part of the showplatform in the SC where the frame led is on and prtdiag in the OS 5.9
Frame: 0003ba:694412 (Mon Feb 25 17:25:18 PST 2008)
Fail LED:Off Service LED:Off
Frame Fan Trays
Left Tray Right Tray
State: OK OK
Power LED: On On
Fault LED: Off Off
Service LED: Off Off
Speed: Slow Slow
Temperature: Normal Normal
Power: OK OK
Fan 0: OK OK
Fan 1: OK OK
Fan 2: OK OK
Frame RTS
Rear/Left - OK, Connected to the System
Rear/Right - OK
Front/Left - OK, Connected to the System
Front/Right - OK
root@server> prtdiag
System Configuration: Sun Microsystems sun4u Sun Fire E6900
System clock frequency: 150 MHz
Memory size: 114688 Megabytes
========================= CPUs ===============================================
CPU Run E$ CPU CPU
FRU Name ID MHz MB Impl. Mask
/N0/SB0/P0 0,512 1500 32.0 US-IV+ 2.2
/N0/SB0/P1 1,513 1500 32.0 US-IV+ 2.2
/N0/SB0/P2 2,514 1500 32.0 US-IV+ 2.2
/N0/SB0/P3 3,515 1500 32.0 US-IV+ 2.2
/N0/SB1/P0 4,516 1500 32.0 US-IV+ 2.2
/N0/SB1/P1 5,517 1500 32.0 US-IV+ 2.2
/N0/SB1/P2 6,518 1500 32.0 US-IV+ 2.2
/N0/SB1/P3 7,519 1500 32.0 US-IV+ 2.2
/N0/SB2/P0 8,520 1500 32.0 US-IV+ 2.2
/N0/SB2/P1 9,521 1500 32.0 US-IV+ 2.2
/N0/SB2/P2 10,522 1500 32.0 US-IV+ 2.2
/N0/SB2/P3 11,523 1500 32.0 US-IV+ 2.2
/N0/SB3/P0 12,524 1500 32.0 US-IV+ 2.2
/N0/SB3/P1 13,525 1500 32.0 US-IV+ 2.2
/N0/SB3/P2 14,526 1500 32.0 US-IV+ 2.2
/N0/SB3/P3 15,527 1500 32.0 US-IV+ 2.2
/N0/SB4/P0 16,528 1500 32.0 US-IV+ 2.2
/N0/SB4/P1 17,529 1500 32.0 US-IV+ 2.2
/N0/SB4/P2 18,530 1500 32.0 US-IV+ 2.2
/N0/SB4/P3 19,531 1500 32.0 US-IV+ 2.2
/N0/SB5/P0 20,532 1500 32.0 US-IV+ 2.2
/N0/SB5/P1 21,533 1500 32.0 US-IV+ 2.2
/N0/SB5/P2 22,534 1500 32.0 US-IV+ 2.2
/N0/SB5/P3 23,535 1500 32.0 US-IV+ 2.2
========================= Memory Configuration ===============================
Logical Logical Logical
Port Bank Bank Bank DIMM Interleave Interleave
FRU Name ID Num Size Status Size Factor Segment
/N0/SB0/P0/B0 0 0 2048MB pass 1024MB 16-way 0
/N0/SB0/P0/B1 0 1 2048MB pass 1024MB 16-way 0
/N0/SB0/P0/B0 0 2 2048MB pass 1024MB 16-way 0
/N0/SB0/P0/B1 0 3 2048MB pass 1024MB 16-way 0
/N0/SB0/P1/B0 1 0 2048MB pass 1024MB 16-way 0
/N0/SB0/P1/B1 1 1 2048MB pass 1024MB 16-way 0
/N0/SB0/P1/B0 1 2 2048MB pass 1024MB 16-way 0
/N0/SB0/P1/B1 1 3 2048MB pass 1024MB 16-way 0
/N0/SB0/P2/B0 2 0 2048MB pass 1024MB 16-way 0
/N0/SB0/P2/B1 2 1 2048MB pass 1024MB 16-way 0
/N0/SB0/P2/B0 2 2 2048MB pass 1024MB 16-way 0
/N0/SB0/P2/B1 2 3 2048MB pass 1024MB 16-way 0
/N0/SB0/P3/B0 3 0 2048MB pass 1024MB 16-way 0
/N0/SB0/P3/B1 3 1 2048MB pass 1024MB 16-way 0
/N0/SB0/P3/B0 3 2 2048MB pass 1024MB 16-way 0
/N0/SB0/P3/B1 3 3 2048MB pass 1024MB 16-way 0
/N0/SB1/P0/B0 4 0 1024MB pass 512MB 16-way 1
/N0/SB1/P0/B1 4 1 1024MB pass 512MB 16-way 1
/N0/SB1/P0/B0 4 2 1024MB pass 512MB 16-way 1
/N0/SB1/P0/B1 4 3 1024MB pass 512MB 16-way 1
/N0/SB1/P1/B0 5 0 1024MB pass 512MB 16-way 1
/N0/SB1/P1/B1 5 1 1024MB pass 512MB 16-way 1
/N0/SB1/P1/B0 5 2 1024MB pass 512MB 16-way 1
/N0/SB1/P1/B1 5 3 1024MB pass 512MB 16-way 1
/N0/SB1/P2/B0 6 0 1024MB pass 512MB 16-way 1
/N0/SB1/P2/B1 6 1 1024MB pass 512MB 16-way 1
/N0/SB1/P2/B0 6 2 1024MB pass 512MB 16-way 1
/N0/SB1/P2/B1 6 3 1024MB pass 512MB 16-way 1
/N0/SB1/P3/B0 7 0 1024MB pass 512MB 16-way 1
/N0/SB1/P3/B1 7 1 1024MB pass 512MB 16-way 1
/N0/SB1/P3/B0 7 2 1024MB pass 512MB 16-way 1
/N0/SB1/P3/B1 7 3 1024MB pass 512MB 16-way 1
/N0/SB2/P0/B0 8 0 1024MB pass 512MB 16-way 2
/N0/SB2/P0/B1 8 1 1024MB pass 512MB 16-way 2
/N0/SB2/P0/B0 8 2 1024MB pass 512MB 16-way 2
/N0/SB2/P0/B1 8 3 1024MB pass 512MB 16-way 2
/N0/SB2/P1/B0 9 0 1024MB pass 512MB 16-way 2
/N0/SB2/P1/B1 9 1 1024MB pass 512MB 16-way 2
/N0/SB2/P1/B0 9 2 1024MB pass 512MB 16-way 2
/N0/SB2/P1/B1 9 3 1024MB pass 512MB 16-way 2
/N0/SB2/P2/B0 10 0 1024MB pass 512MB 16-way 2
/N0/SB2/P2/B1 10 1 1024MB pass 512MB 16-way 2
/N0/SB2/P2/B0 10 2 1024MB pass 512MB 16-way 2
/N0/SB2/P2/B1 10 3 1024MB pass 512MB 16-way 2
/N0/SB2/P3/B0 11 0 1024MB pass 512MB 16-way 2
/N0/SB2/P3/B1 11 1 1024MB pass 512MB 16-way 2
/N0/SB2/P3/B0 11 2 1024MB pass 512MB 16-way 2
/N0/SB2/P3/B1 11 3 1024MB pass 512MB 16-way 2
/N0/SB3/P0/B0 12 0 1024MB pass 512MB 16-way 3
/N0/SB3/P0/B1 12 1 1024MB pass 512MB 16-way 3
/N0/SB3/P0/B0 12 2 1024MB pass 512MB 16-way 3
/N0/SB3/P0/B1 12 3 1024MB pass 512MB 16-way 3
/N0/SB3/P1/B0 13 0 1024MB pass 512MB 16-way 3
/N0/SB3/P1/B1 13 1 1024MB pass 512MB 16-way 3
/N0/SB3/P1/B0 13 2 1024MB pass 512MB 16-way 3
/N0/SB3/P1/B1 13 3 1024MB pass 512MB 16-way 3
/N0/SB3/P2/B0 14 0 1024MB pass 512MB 16-way 3
/N0/SB3/P2/B1 14 1 1024MB pass 512MB 16-way 3
/N0/SB3/P2/B0 14 2 1024MB pass 512MB 16-way 3
/N0/SB3/P2/B1 14 3 1024MB pass 512MB 16-way 3
/N0/SB3/P3/B0 15 0 1024MB pass 512MB 16-way 3
/N0/SB3/P3/B1 15 1 1024MB pass 512MB 16-way 3
/N0/SB3/P3/B0 15 2 1024MB pass 512MB 16-way 3
/N0/SB3/P3/B1 15 3 1024MB pass 512MB 16-way 3
/N0/SB4/P0/B0 16 0 1024MB pass 512MB 16-way 4
/N0/SB4/P0/B1 16 1 1024MB pass 512MB 16-way 4
/N0/SB4/P0/B0 16 2 1024MB pass 512MB 16-way 4
/N0/SB4/P0/B1 16 3 1024MB pass 512MB 16-way 4
/N0/SB4/P1/B0 17 0 1024MB pass 512MB 16-way 4
/N0/SB4/P1/B1 17 1 1024MB pass 512MB 16-way 4
/N0/SB4/P1/B0 17 2 1024MB pass 512MB 16-way 4
/N0/SB4/P1/B1 17 3 1024MB pass 512MB 16-way 4
/N0/SB4/P2/B0 18 0 1024MB pass 512MB 16-way 4
/N0/SB4/P2/B1 18 1 1024MB pass 512MB 16-way 4
/N0/SB4/P2/B0 18 2 1024MB pass 512MB 16-way 4
/N0/SB4/P2/B1 18 3 1024MB pass 512MB 16-way 4
/N0/SB4/P3/B0 19 0 1024MB pass 512MB 16-way 4
/N0/SB4/P3/B1 19 1 1024MB pass 512MB 16-way 4
/N0/SB4/P3/B0 19 2 1024MB pass 512MB 16-way 4
/N0/SB4/P3/B1 19 3 1024MB pass 512MB 16-way 4
/N0/SB5/P0/B0 20 0 1024MB pass 512MB 16-way 5
/N0/SB5/P0/B1 20 1 1024MB pass 512MB 16-way 5
/N0/SB5/P0/B0 20 2 1024MB pass 512MB 16-way 5
/N0/SB5/P0/B1 20 3 1024MB pass 512MB 16-way 5
/N0/SB5/P1/B0 21 0 1024MB pass 512MB 16-way 5
/N0/SB5/P1/B1 21 1 1024MB pass 512MB 16-way 5
/N0/SB5/P1/B0 21 2 1024MB pass 512MB 16-way 5
/N0/SB5/P1/B1 21 3 1024MB pass 512MB 16-way 5
/N0/SB5/P2/B0 22 0 1024MB pass 512MB 16-way 5
/N0/SB5/P2/B1 22 1 1024MB pass 512MB 16-way 5
/N0/SB5/P2/B0 22 2 1024MB pass 512MB 16-way 5
/N0/SB5/P2/B1 22 3 1024MB pass 512MB 16-way 5
/N0/SB5/P3/B0 23 0 1024MB pass 512MB 16-way 5
/N0/SB5/P3/B1 23 1 1024MB pass 512MB 16-way 5
/N0/SB5/P3/B0 23 2 1024MB pass 512MB 16-way 5
/N0/SB5/P3/B1 23 3 1024MB pass 512MB 16-way 5
========================= IO Cards =========================
Bus Max
IO Port Bus Freq Bus Dev,
FRU Name Type ID Side Slot MHz Freq Func State Name Model
/N0/IB6/P0 PCI 24 B 0 33 33 1,0 ok pci-pci8086,b154.0/network (netw+ pci-bridge
/N0/IB6/P0 PCI 24 B 0 33 33 0,0 ok network-pci100b,35.30 SUNW,pci-ce
/N0/IB6/P0 PCI 24 B 0 33 33 1,0 ok network-pci100b,35.30 SUNW,pci-ce
/N0/IB6/P0 PCI 24 B 0 33 33 2,0 ok scsi-pci1000,b.7/disk (block)
/N0/IB6/P0 PCI 24 B 0 33 33 2,1 ok scsi-pci1000,b.7/disk (block)
/N0/IB6/P0 PCI 24 A 3 66 66 1,0 ok network-pci100b,35.30 SUNW,pci-ce
/N0/IB6/P1 PCI 25 B 4 66 66 1,0 ok pci-pci8086,537c.7/network (netw+ pci-bridge
/N0/IB6/P1 PCI 25 B 4 66 66 0,0 ok network-pci100b,35.30 SUNW,pci-x-qge
/N0/IB6/P1 PCI 25 B 4 66 66 1,0 ok network-pci100b,35.30 SUNW,pci-x-qge
/N0/IB6/P1 PCI 25 B 4 66 66 2,0 ok network-pci100b,35.30 SUNW,pci-x-qge
/N0/IB6/P1 PCI 25 B 4 66 66 3,0 ok network-pci100b,35.30 SUNW,pci-x-qge
/N0/IB6/P1 PCI 25 A 7 66 66 1,0 ok SUNW,qlc-pci1077,2312.1077.10a.2+ 0x10a
/N0/IB6/P1 PCI 25 A 7 66 66 1,1 ok SUNW,qlc-pci1077,2312.1077.10a.2+ 0x10a
/N0/IB7/P0 PCI 26 B 0 33 33 1,0 ok pci12d4,301-pci12d4,301.12d4.301+
/N0/IB7/P0 PCI 26 B 1 33 33 2,0 ok pci12d4,301-pci12d4,301.12d4.301+
/N0/IB7/P0 PCI 26 A 2 66 66 2,0 ok pci12d4,301-pci12d4,301.12d4.301+
/N0/IB7/P0 PCI 26 A 3 66 66 1,0 ok pci12d4,301-pci12d4,301.12d4.301+
/N0/IB8/P0 PCI 28 B 0 33 33 1,0 ok pci-pci8086,b154.0/network (netw+ pci-bridge
/N0/IB8/P0 PCI 28 B 0 33 33 0,0 ok network-pci100b,35.30 SUNW,pci-ce
/N0/IB8/P0 PCI 28 B 0 33 33 1,0 ok network-pci100b,35.30 SUNW,pci-ce
/N0/IB8/P0 PCI 28 B 0 33 33 2,0 ok scsi-pci1000,b.7/disk (block)
/N0/IB8/P0 PCI 28 B 0 33 33 2,1 ok scsi-pci1000,b.7/disk (block)
/N0/IB8/P0 PCI 28 A 3 66 66 1,0 ok network-pci100b,35.30 SUNW,pci-ce
/N0/IB8/P1 PCI 29 B 4 66 66 1,0 ok pci-pci8086,537c.7/network (netw+ pci-bridge
/N0/IB8/P1 PCI 29 B 4 66 66 0,0 ok network-pci100b,35.30 SUNW,pci-x-qge
/N0/IB8/P1 PCI 29 B 4 66 66 1,0 ok network-pci100b,35.30 SUNW,pci-x-qge
/N0/IB8/P1 PCI 29 B 4 66 66 2,0 ok network-pci100b,35.30 SUNW,pci-x-qge
/N0/IB8/P1 PCI 29 B 4 66 66 3,0 ok network-pci100b,35.30 SUNW,pci-x-qge
/N0/IB8/P1 PCI 29 A 7 66 66 1,0 ok SUNW,qlc-pci1077,2312.1077.10a.2+ 0x10a
/N0/IB8/P1 PCI 29 A 7 66 66 1,1 ok SUNW,qlc-pci1077,2312.1077.10a.2+ 0x10a
/N0/IB9/P0 PCI 30 B 0 33 33 1,0 ok pci12d4,301-pci12d4,301.12d4.301+
/N0/IB9/P0 PCI 30 B 1 33 33 2,0 ok pci12d4,301-pci12d4,301.12d4.301+
/N0/IB9/P0 PCI 30 A 2 66 66 2,0 ok pci12d4,301-pci12d4,301.12d4.301+
/N0/IB9/P0 PCI 30 A 3 66 66 1,0 ok pci12d4,301-pci12d4,301.12d4.301+
========================= Active Boards for Domain ===========================
Board Receptacle Occupant
FRU Name Type Status Status Condition Info
/N0/SB0 CPU_V3 connected configured ok powered-on, assigned
/N0/SB1 CPU_V3 connected configured ok powered-on, assigned
/N0/SB2 CPU_V3 connected configured ok powered-on, assigned
/N0/SB3 CPU_V3 connected configured ok powered-on, assigned
/N0/SB4 CPU_V3 connected configured ok powered-on, assigned
/N0/SB5 CPU_V3 connected configured ok powered-on, assigned
/N0/IB6 PCI+I/OBo connected configured ok powered-on, assigned
/N0/IB7 PCI+I/OBo connected configured ok powered-on, assigned
/N0/IB8 PCI+I/OBo connected configured ok powered-on, assigned
/N0/IB9 PCI+I/OBo connected configured ok powered-on, assigned
========================= Available Boards/Slots for Domain ===========================
Board Receptacle Occupant
FRU Name Type Status Status Condition Info
There are currently no Boards/Slots available to this Domain
========================= Hardware Failures ==================================
No Hardware failures found in SystemIf I understand your description correctly,
it's the frame manager that has the fault light.
That's an old quirk that is specific to that rack component.
It has (essentially) no impact on whatever systems are installed to the rack.
It is usually just a visual annoyance.
Use your service contract and open a support case with Sun.
That will give them a chance to help you check on everything.
They'll walk you through the correct steps of power-cycling the frame manager.
That can be done while the servers are happily serving. -
How to turn off i-pad when circle coniues inmiddle/
How do I turn off my i-pad 2 when the circle coninues in the middle of the screen?
Have you tried a reset and then tried shutting down after the iPad has restarted ? Press and hold both the sleep and home buttons for about 10 to 15 seconds, after which the Apple logo should appear - you won't lose any content, it's the iPad equivalent of a reboot.
-
Don't know how to turn off T420 LED light
I upgraded my thinkpad T420 to Windows 8. Everything is good, but the Bluetooth LED light is always turned on. I don't know how to turn it off. Does anyone have same situation?
Yes, unfortunately. You can turn off the bluetooth led by disabling bluetooth in the bios. Not very convenient if u use Bluetooth regularly.
-
MSI Z87 GD65 "Dragon" Motherboard - How to turn OFF blue LED?
Hi guys, recently purchased this motherboard for my i7 4770k and I LOVE IT. BIOS works great and the computer boots up flawless with no errors.
My question is, the motherboard has a red theme to it, and my case is red/black as-well.
However, the mobo has a BLUE LED on it, when it is powered on. I Looked in BIOS but could not find a way to turn it off.
Is there any way to turn this blue LED off? It kind of ruins the red/black theme! :(
Please let me know,
Thank you!Nope , the option is NOT under hardware monitor
There is a "Power LED" option under the "advanced" setting, but it doesn't affect the "blue LED" for the BIOS , only the purple-redish LED for "audio" on the motherboard..... -
How to turn off red highlight warning
how do i turn off the red highlight warning in lightroom that is all of a sudden appearing?
The [ J ] Key
or
Click on the Triangle in the upper right corner of the Histogram panel -
How to turn off number sounds when dialing out?
? I have the keyboard sound off already, but, when I dial out the numbers are not silent.
The keyboard is just that, ...the keyboard, ....used only for text, email and web. The phone dialing screen is totally different and is uneffected by any changes you make to the keyboard settings. The only way to silence the phone when dialing out is to either turn the volume all the way down (not logical) or to engage the mute slide on the side of the phone. **Warning, ...both options also turn the ringer off or down. I would like to see apple address this in the next update. Users don't need to hear these loud numbers.
-
How to turn OFF status LED on VC220?
I'm looking for a way to turn off the status LED on a VC220. This is not the IR LED, but instead the large blinking LED on the front.
The documentation mentions that it can be turned off, but I can't find a menu option for this.
Thanks for your help!
--Joe
Status LED
Indicates the following status:
LED Off—The power is off or the LED status is turned off.
Flashing green in one second intervals—The camera and network is functioning.
Steady orange—The camera can’t detect a networking signal; thus the camera is not functioning. For example, the Ethernet cable is not attached.
Flashing orange—The PIR sensor noted movement. Flashing green rapidly—The firmware is being
upgraded.
Flashing orange rapidly—The camera’s default settings are being restored.
Alternating flashing green and orange—Video has been lost.Joe,
Use the Network Setting > IP Setting page to set the IP address and other related
settings. When you complete the configuration, click Save to save the settings;
otherwise click Cancel to discard the changes.
• Disable LED Operators—Select to disable the LED illuminators. You may
choose to do this if you don't want to alert others that the network camera is
on. Use the Network Setting > IP Setting page to set the IP address and other related
settings. When you complete the configuration, click Save to save the settings;
otherwise click Cancel to discard the changes.
http://www.cisco.com/en/US/docs/security/csbvsc/vc220/administration/guide/VC220AdministrationGuide.pdf
page; 41
Hope this is what you're looking for,
Jasbryan -
How to turn off Wi-Fi when I leave home?
I like to have Wi-Fi on when I'm home.
However, when I'm not at home, I'd like to have it off, to save battery - and back on when I return.
Is there a way to do this using Siri (disappointingly - I'm pretty sure not) or to do it using location-based services - similar to location-based reminders ("Remind me to feed the cat when I get home")?
I'd rather not have to manually edit Settings->Wi-Fi all the time.
Thanks.as far as i know there isnt way to turn off the wifi..however u can go to tools-settings-connection-wireless LAN -show availability -never
this way it saves the battery of your phone and keeps u away from unwanted connection
try out!!! -
How to turn off suggested sites when using - Inbox
I don't want the suggested sites. Displaying them causes problems when rand children use computer.
You can turn off search suggestions & auto complete through Firefox & the search engine settings etc. depending specifically on what you are wanting to achieve.
See:
[[Search suggestions]] -
Satellite A660-11M how to turn off the screen when I'm downloading?
i just want to know how to trurn off the screen for save energy and protect the screen,someone tell me please! thanks a lot !
If you are ready to switch off, put to standby/sleep mode you laptop by pressing alt-F3-F4 or through menu, then I recommend you set in power options "when I close the lid-do nothing". In that case closing the lid will switch off the screen for downloading time.
-
How to turn off "save as" when opening a project template?
Every time i open my template and want to start working, there's logic's menu appears which offer "save current project as", how can i turn it off? if i want to save i will do it manually when create something cool.
didn't find it in preferences/general/startup action.
any thoughts will be appreciated.my sine is fine wrote:
well, every time when i switch record button it always asks me where to save recorded data.
My point exactly. By not permitting Logic to establish a functional folder sturucture, you ask for a lot more mouseclicks and distractions than necessary.
so thanks but i still don't know how to avoid that "save as"
Do as I said, save it once and live happily ever after.
Christian -
How to turn off XML tag when outputting xml nodes?
I'm outputting some xml data and each time ColdFusion adds the <?xml version="1.0" encoding="UTF-8"?> tag. Is there any way to turn this off?
It's difficult to tell what are are doing and how best to remedy it without you giving us at least some idea what your code looks like.
Adam -
How to turn off image info when hovering mouse over image?
I think I must have selected something by accident because now everytime I hover my mouse over an image, I get all this info about that image. I know it can be info will be good to know but I don't want to see it all the time. I can't find anything in the settings that seems like it would be able turn it off.
suggestions?ress the T key on your keyboard
-
How do I turn off SMS preview, I have the new update but it doesn't show up in Passcode lock settings. I have an iPhone4
Go to Settings > Notifications > Messages > Show Preview ON/OFF
Maybe you are looking for
-
When doing a "Network Connectivity Test" on my PC, while in iTunes, it tells me that "Secure Link to iTunes Store Failed", yet I'm connected to the internet. I was unable to "authorize" my PC with an error message, as well, giving me the code (-3212
-
Creating an Hyperion Planning connection in Financial Reporting
We've got a lot of FM and Essbase reports, but now I'd like to connect to Planning so that I can display cell text in a report but I just can't get the connection setup from Workspace. Two things: 1. There's no button to pick my Application as with o
-
hi dear, i have one log in page.when i logged in i got a form and in that form belodata is there like formid formname ovf_o1 entry form for student ovf_o2 entry form for teacher my question is if i click on entry form for student .then that particula
-
I just got a new air running SL, seems like when I use Safari browser it is really really slow even though I have full connectivity to wireless router. When I use Firefox it is way faster. Any tips for getting Safari to speed up? Thanks
-
Reports layout - how flexible?
As far as I can see when I'm creating reports there are two basic type of layouts - one is a table where the columns are one next to the other, and the other is a "form" where the fields are one is under the other. Can I somehow get more flexible lay