How to upgrade my firmware

hi i would like some step by step assistance in upgrading the firmware on my cisco 2504 wireless controller and my 
cisco Acap 35021-A-K9 access points.
Any given assistance is greatly appreciated.
BDF TECH

Here are the steps:
http://www.cisco.com/c/en/us/support/docs/wireless-mobility/wireless-lan-wlan/68835-wlc-upgrade.html
FUS upgarde procedure:
http://www.cisco.com/c/en/us/td/docs/wireless/controller/release/notes/fus_rn_OL-31390-01.html
Make sure you take a downtime for atleast 60 minutes for all process.(software + FUS).

Similar Messages

  • How to Upgrade PowerBook Firmware( All Hardwares )

    How to Upgrade PowerBook Firmware( All Hardwares )?
    Thank U in advance

    If there is a firmware upgrade available for your model of PowerBook, it will appear when your run Software Update and also be listed at http://www.apple.com/support/downloads/
    Then you download the installer and run it. Usually you have to do something like hold down the Command key and Power button while you're restarting.
    Firmware updates don't come along very often. The last one I can remember installing was for my B&W G3. The last firmware upgrades I can see listed for a PowerBook were for the 550MHz or 667MHz G4s back in 2002.
    Is there a specific reason why you're asking about firmware upgrades?

  • How to upgrade/downgrade firmware of following switch.

    How to upgrade/downgrade firmware of following switch.
                         Please kindly inform how to do it.
                         - Download site
                         - Process required
                      [Version that  want to use]
     ・Catalyst3750X ： 15.0(2)SE6
      ・ASA5525-X ： 9.1(2)
     ・ASA5525-X  ASDM ： 7.1(6)

    Upgrade to ASA 9.3 and ASDM 7.3

  • How to upgrade e50 firmware via apple mac?

    I own an E50 (RM-170) which is currently running v 06.41.3.0.
    How do I tell what the most up-to-date firmware is?
    And how do I upgrade the firmware into the phone using an Apple Mac? (I saw the updater software for Windows but couldn't see a Mac version).
    Thanks
    Peter Crow, New Zealand 

    Check on the Nokia software update site for your specific model. Be aware that they release firmware for different regions at different times.
    As for upgrading via a Mac, that isn't available as yet.
    Don't bother trying through Parallels. I have and it doesn't work.
    Sanjay Mehta
    Motorola "Brickphone" circa 1996, Alcatel One Touch, Ericsson R380, Sony Ericsson T220, Sony Ericsson T630, Nokia E50, Nokia E61i, Nokia 9300i, Nokia E71,Nokia X6, Google Nexus S, iPhone 4S

  • How to upgrade handheld firmware to the most available recent version

    Hi,
    I have a BB 8800 (T-Mobile) and I tried to update current firmware (4.2.1.101) to the recent OS version. I went to the T-Mobile site and found that there was older version (4.2.1.74) than installed on my handheld.
    So, I did the following. I checked all carries on this page and found that Orange UK offers handheld version 4.5 for BB8800.
    I downloaded handheld 4.5 software from Orange UK site. Installed it on my PC.
    Deleted the VENDOR.XML file located at:
    C:\Program Files\Common Files\Research In Motion\AppLoader\VENDOR.XML
    After that I connected my handheld to the PC and ran Blackberry Desktop Manager.
    And it upgraded my handheld OS to the 4.5.0.52
    if your issue solved set "Solution" mark at the relevant post
    Solved!
    Go to Solution.

    i can suggest this guide:
    http://www.blackberrycool.com/2008/08/how-to-upgrade-your-blackberry-software/
    feel free to press the like button on the right side to thank the user that helped you.
    please mark posts as solved if you found a solution.
    @SimonHain on twitter

  • How to upgrade driver/firmware for 3rd party airport card?

    I have a Motorola WPCI810g wireless card that i have been using for over a year. Previously in Panther i tried to upgrade to Airport 4.2 to take advantage of WPA, but i ended up having to downgrade back to 4.1 because 4.2 left airport nonoperational. I have been on Tiger for quite a while and only recently noticed that i was automatically upgraded to Airport 4.2, however I do not have WPA as an encryption option (neither when joining, or creating a network). I can only assume it has to do with the firmware on the card but I cant figure out how to update it. I have tried to search these threads but the closest i can come is using Airport Admin Utility to upgrade the firmware on a base station.
    About Airport is such:
    Airport
    427.1.1
    Component Versions:
    Airport Menu Extra: 427.1.1
    Airport Framework: 429.6.0
    Airport Extreme Driver: 405.1.0
    Airport Admin Utility: 420.5.0
    Airport Setup Assistant: 420.6.0
    Powermac G3 Rev2 B&W 400mhz, iBook G4 14" 1.33mhz   Mac OS X (10.4.9)   Pioneer DVR-109, Moto WPCI810G, Nano (1G) 4gb Black

    yup, and this is what it says:
    AirPort Card Information:
    Wireless Card Type: AirPort Extreme
    Wireless Card Locale: USA
    Wireless Card Firmware Version: 405.1 (3.90.34.0.p18)
    Current Wireless Network: wireless network not available
    in addition, I found that I can choose WPA as an encryption if i select 'other' as the network. What I would really like to do is create a network with WPA, since i use this desktop to connect my ibook to the internet. so far nothing...

  • HT1414 How to upgrade the firmware on i phone

    Please advise how to upgrade the I Phone 4 ???

    Connect iPhone to syncing computer using USB cable.
    Start iTunes on syncing computer.
    Follow prompts from iTunes to upgrade.

  • How to upgrade SSD firmware without the CD drive?

    Hello
    I have a X300 (6478-1HP) with the optional battery instad of the CD-ROM drive. That drive just stopped working, it just can't read dics anymore. I'm happy with my Samsung USB CD-ROM, runs great.
    But how can I upgrade my SSD drive with the new firmware just released? The readme.txt states that we should not use USB drives to do it. What now? Anyone tried already?
    Thanks,
    Rebêlo.
    www.rebelo.org

    You HAVE to have access to a Computer to upgrade your iPad.  You can NOT do it thru 3G/WiFi.  That is why you are getting that message.
    Hope this helps

  • How to upgrade the firmware of the WRT54G v.5 router

    Please refer to this link:
    http://linksys.custhelp.com/cgi-bin/linksys.cfg/php/enduser/std_adp.php?p_faqid=3410
    Message Edited by Vince_02 on 06-11-2006 05:35 PM

    Thanks Vince

  • MSI DR4-A,How do I upgrade the firmware? (How do I flash?)

    I can't use my MSI DR4-A for anything now since i dont know how to upgrade the firmware (flash) can somebody please explain how to flash it better then the ReadMe file the lates update came with..cause i seriously don't understand the readme neither does any of my friends..so please help me someone...

    I updated the Firmware yesterday, what I did was the following.
    Downloaded the latest (2.50) firmware from the download page, and putted all the files (DVFLASH.EXE and 250D.BIN) on a floppy.
    Went to Bootdisk.com and downloaded the win98SE OEM bootdisk (as suggested by others here) and ran the exe by using a second floppy.
    Rebooted my pc with the newly created bootdisk in the floppy drive.
    After a while you'll see the prompt.
    Replace the bootdisk with the disk where DVFLASH.EXE and 250D.BIN is on and make sure the promt says A:\ (assuming this is your floppy drive).
    Then type DVFLASH 250D.BIN
    (also assuming the version is 250D.bin, which it is now atm).

  • What file do I use to upgrade WRT54GL firmware?

    Just got a new WRT54GL wirless router and am interested in how to upgrade the firmware. Downloaded WRT54GL_v4.30.9_US.tgz from the Linsys support/download website. It's a zip file that contains WRT54GL_v4.30.9_US.tar which is another zip file that contains the source files. But there's no compiled file.  Where can I get an executable that can be downloaded to the router?

    You'd have to ask Linksys that question....but if the firmware for the 1.0 and the 1.1 are the same, they may just have forgotten to update the page...or they may just consider that if there are no firmware updates for the 1.1, why bother posting it...after all, no one should ever need to re-flash their routers, right??  
    Tomato 1.25vpn3.4 (SgtPepperKSU MOD) on a Buffalo WHR-HP-G54
    D-Link DSM-320 (Wired)
    Wii (Wireless) - PS3 (Wired), PSP (Wireless) - XBox360 (Wired)
    SonyBDP-S360 (Wired)
    Linksys NSLU2 Firmware Unslung 6.10 Beta unslung to a 2Gb thumb, w/1 Maxtor OneTouch III 200Gb
    IOmega StorCenter ix2 1TB NAS
    Linksys WVC54G w/FW V2.12EU
    and assorted wired and wireless PCs and laptops

  • How to upgrade IP/KVM Console AF620A via serial interface?

    Hi
    I've got a "HP 1x1Ex8 KVM IP Console Switch G2 with Virtual Media CAC Software - AF620A" which is not booting correctly anymore.
    Symptoms:
    - blank screen
    - status leds constantly blinking
    - serial output hangs after "Booting:1.2.10.15038"
    Hooking up to the serial interface, the terminal gives me, that the current version as well as the alternate version of the used firmware is 1.2.10.15038. As far as I was able to find out, I should upgrade to the latest firmware in order to get rid of the problem and make the device usable again.
    My problem is, that I don't know how to upgrade the firmware via the serial console, knowing that the device is not booting up the firmware.
    Yes, I've done a factory reset as well as a configuration reset. No change ...
    I've opened up the case to see if there is any hardware reset button, but there is none. The only thing I found is a 4pin header labeled "HDR2" but neither the user guide not the technical guide gives any details about the interior of the device (of course not ...).
    Has anyone had the same problem with this or any similar device?
    Or does anyone has a good advice what I could try to revive the KVM?
    greetings

    I finally got through the helpline, but as my device is out of warranty, the official solution for my problem is to buy a new device!
    Ending is better than mending ... welcome our the brave new world ...

  • FAQ Broken: How do I upgrade the firmware on a WRT54G Wireless-G Broadband Router?

    I tried to view the above question in the FAQ, but it goes to the answer for a different question.
    I then tried "How do I upgrade the firmware on my router?" a little further down,
    but it acts like I'm not authenticated, and won't accept my Linksys Forums e-mail address
    and password. When I try the password recovery, it says my e-mail address is invalid.
    Can someone please point me to instructions for upgrading the firmware on my WRT54G?
    Specifically, someone told me that the router needs to be listening on the default 192.168.1.1
    IP address, but mine is listening on 10.1.1.2. Do I need to change this just to flash new
    firmware, because that will be a little painful.
    Thanks,

    Go to website linksysbycisco.com/downloads.........insert model no of your router in serach tab......select proper version of your router........download the firmware file......save that file on desktop
    Follow these steps to upgrade the firmware on the device : -
    Open an Internet Explorer browser page on a computer hard wired to the router...
    In the address bar type - "Default Gateway of Your Router"...Leave the Username blank & in Password use admin in lower case...
    Click on the 'Administration' tab- Then click on the 'Firmware Upgrade' sub tab- Here click on 'Browse' and browse the .bin firmware file and click on "Upgrade"...
    Wait for few seconds until it shows that "Upgrade is successful"  After the firmware upgrade, click on "Reboot" and you will be returned back to the same page OR it will say "Page cannot be displayed".
    Now reset your router :
    Press and hold the reset button for 30 seconds...Release the reset button...Unplug the power cable from your router, wait for 30 seconds and re-connect the power cable...Now re-configure your router...
    **To Check the Default Gateway of the router...Click Start >> All Programs >> Accessories >> Command Prompt...A black box will appear(Command Prompt)...In the Command Prompt window type ipconfig and press 'Enter'...Look for Ethernet Adapter Local Area Connection IP Address , Subnet Mask and Default Gateway...
    **To all the above setting using the wired computer.

  • How to upgrade firmware on 7921g wireless phone from 1.0.2 to 1.0.4 via USB

    how to upgrade firmware on 7921g wireless phone from 1.0.2 to 1.0.4 via USB?
    The 7921g is connected via USB to a PC. I am using a browser to access the phone. Documentation says "Click the Phone Upgrade hyperlink under SYSTEM options. " but that option is not present or not visible.

    You can use the Phone Upgrade area on the web page to upgrade firmware files on the phones by using the USB connection or by using the WLAN. To upgrade the phone software, enter the phone software TAR (firmware file name) or use the Browse button to locate the firmware file on the network.
    To display the Phone Upgrade area, access the web page for the phone as described in the Accessing the Configuration Web Page for a Phone section available at http://www.cisco.com/en/US/docs/voice_ip_comm/cuipph/7921g/5_0_1/english/administration/guide/21adm50.pdf

  • How to upgrade retina samsung oem ssd firmware

    Hi Guys
    A friend of mine has given me their ssd drive from their 2012 retina,as they are upgrading.
    I will be putting it in a windows laptop via a normal sata adaptor.
    How can I update the firmware for it, also where can I get it from?
    Will the magician softwae work?
    I know normally an update would be done from the mac app store but I do not have acess to an apple.
    any help appreciated.

    Hi-
    It isn't necessary to upgrade the firmware for an ATI card. Most available upgrade options will work fine in Leopard.
    The ATI 9800 Pro Mac works very well with Leopard, and supports Core Image, which Leopard uses more so than Tiger.
    Personally, with two different versions of the 9800 (one 256mb, and one 128mb) there have been no issues with firmware.
    With a flashed (converted PC) graphics card, most all people are using the latest ROM version. Beyond this, nothing else is necessary.

Maybe you are looking for

  • Facebook like widget not showing up in safari

    Works fine in chrome, firefox and IE. Tried resetting safari, no luck.

  • ALV Grid Layout problem

    I have define a form layout on the first screen (ALV) of my program then the program call another screen,  the same layout is applied to the new screen 0200 (ALV). I don't want the same layout been applied to the new screen. What is my problem? Regar

  • Table columns

    hi I want show my information in table like this how to do this table Format in webdynpro        cost     budget     persontage     toatl baseline                     randamise and in one column i want to show links      regards Narain

  • How  can i run this code correctly?

    hello, everybody:     when  i run the code, i found that it dons't work,so ,i  hope somebody can help me!     the Ball class is this :     package {     import flash.display.Sprite;     [SWF(width = "550", height = "400")]     public class Ball exten

  • How do you add more Artboards numerically?

    Ok, I know how to go into edit artboards and option drag the artboard to add artboards. But how can I numerically specify that I want, say, 12 artboards instead of 2. (Like adding pages in InDesign)