How to use dual monitor display in windows 7 using MSTSC command.......??????

how to use dual monitor display in windows 7 using MSTSC command ....?????

Hi Anurag,
The main issue is how to use the dual monitor in the Remote Desktop Session in Windows 7 ,right ?
please refer to the following links:
Using Multiple Monitors in Remote Desktop Session
http://blogs.msdn.com/b/rds/archive/2009/07/01/using-multiple-monitors-in-remote-desktop-session.aspx
Best regards

Similar Messages

  • I have 12 core with Quatro 4000 and 5770, I want to use dual monitor setup, monitors are NEC with Spectraview-II.  How do I connect?  4000 only has 1 Display Port and 1 DVI.  5770 has 2 of each, if I use both 5770 Display Ports, does the 4000 contribute?

    I just bought a 12 core with Quatro 4000 and 5770, I want to use dual monitor setup, monitors are NEC with Spectraview-II.  How do I connect?  4000 only has 1 Display Port and 1 DVI.  5770 has 2 of each, if I use both 5770 Display Ports, does the 4000 contribute any work at all?  I read where on a PC they would work together, but on a MAC they do not.
    I read that Display Port has higher band width than DVI, NEC monitors for best performance they recommend using DIsplay Port.
    When I was setting this up I looked at a Nvidia Quadro 4000, unfortunately it was for PC, it had 2 Display Ports, in the Mac version they reduce it to one.  I did not think there could be a difference.
    Mainly want to use it for CS6 and LR4.
    How to proceed??? 
    I do not want to use the Quadro 4000 for both, that would not optimize both monitors, one DP and 1 DVI.  Using just the 5770 would work but I do not think the 4000 would be doing anything, and the 5770 has been replaced by the 5870.more bandwidth.
    Any ideas, I am a Mac newbie, have not ever tried a Mac Pro, just bought off ebay and now I have these problems.
    As a last resort I could sell both and get a 5870.  That would work, I'm sure of that, it's just that I wanted the better graphics card.
    Thanks,
    Bill

    The Hatter,
    I am a novice at Mac so I read all I can.  From what I understand the NEC monitors I bought require Display Port for their maximum performance.  The GTX 680 only has DVI outputs.  Difference from what I understand is larger bandwidth with the DP.
    You said I have the 4000 for CUDA.  I am not all that familiar with CUDA and when I do read about it I do not understand it. 
    A concern I have is, that if I connect the 2 high end NEC monitors via the 5770, using it's 2 Display Ports I would have nothing connected to the 4000.  Is the 4000 doing anything with nothing connected?  I read where in a PC system the 2 cards would interact but in a Mac system they do not.
    Bottom line, as I see it, the 4000 will not be useful at all to me, since I want a dual monitor set-up.
    So far the 5870 seems the best choice, higher band width than the 5770, and it has 2 Display Ports to optimize the NEC monitors.
    I'm not sure how fine I am splitting hairs, nor do I know how important those hairs are.  I am just trying to set up a really fast reliable system that will mainly be used for CS6 and LR4.  Those NEC monitors are supposed to be top notch.

  • HT4293 i am trying to use dual monitors when editing with FCPX. I have a macbook pro and an apple cinema display monitor. I have connected them and opened Fcpx but the option to use second monitor is not active! what do i do ? please help going bonkers!

    i am trying to use dual monitors when editing with FCPX. I have a macbook pro and an apple cinema display monitor. I have connected them and opened Fcpx but the option to use second monitor is not active! what do i do ? please help going bonkers!

    <http://support.apple.com/kb/HT5891>
    You can use USB for the Apple trackpad.
    <http://www.mobeetechnology.com/the-power-bar.html>

  • Dual Monitor display/firmware difference

    I purchased a Pavilion 27xi monitor from the HP Shopping site in October 2014 and purchased an additional 27xi to be used in a dual monitor setup. I received the new monitor this week. The newer monitor does not match the color/white of my existing monitor. When I move a white rectangle so it displays on each monitor, on the new monitor it appears as greenish gray instead of the white of the older monitor. I have done the factory resets, switched display adapter outputs (NVIDIA GeForce 9800 GT), tried one monitor at a time on either adapter output. All with no change in the behavior of the new monitor. The internal setup/control menus of the monitors differ in content and style/color.
    Older monitor info:  manuf: April 2014, Rev: RIM111
    New monitor info:   manuf: Dec 2014,  Rev: RIM232
    I have talked with HP "support" and one person thought it was because of the revision level difference.
    I want the display quality of the older monitor, Rev: RIM111.  If the monitor difference is because of the revision level, can the newer monitor be put at the RIM111 level. I tried to purchase a monitor with the RIM111 level and was told by HP Shopping that they do not have any at that level. I this a firm level that can be changed? If so how do I accomplish that?

    Hello @tomas44,
    Welcome to the HP Forums, I hope you enjoy your experience! To help you get the most out of the HP Forums I would like to direct your attention to the HP Forums Guide First Time Here? Learn How to Post and More.
    I understand that the newest monitor you have connected to your desktop computer does not match the color/white of the existing display, and I would be happy to assist you in this matter!
    To ensure that your system is properly configured for dual monitor displays, I recommend following the steps in this document on Using Two or More Monitors with One Computer (Windows 8). If everything is setup accordingly, I recommend following the steps below for the newest monitor:
    Step 1. Unplug the power cord from the back of the monitor and the wall
    Step 2. Hold the power button down for at least one minute
    Step 3. Plug the power cord back into the monitor and then into the wall outlet (not a power bar or surge protector)
    Step 4. Press the Menu button on the monitor
    Step 5. Navigate to the Factory Reset option and select it
    Step 6. Try a different cable connecting your monitor to your computer
    If the above steps did not resolve your issue you can try the monitor on a computer or other device to see if the issue persists. Please call our technical support at 800-474-6836. If you live outside the US/Canada Region, please click the link below to get the support number for your region.
    http://www8.hp.com/us/en/contact-hp/ww-phone-assist.html
    Thank you for posting on the HP Forums. Have a great day!
    MechPilot
    I work on behalf of HP
    Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
    Click the “Kudos, Thumbs Up" on the right to say “Thanks” for helping!

  • Dual Thunderbolt Displays in Windows 7? Retina Macbook?

    I understand you cannot daisy chain thunderbolt displays in Windows 7 to have dual monitors? Is there another way to run Dual monitors? I have a mid 2012 Macbook pro with on Thunderbolt display. I see the Retina Macbook has two thunderbolt ports. If I got one of those, could use dual Thunderbolt displays then in Windows 7, and then just hook each monitor up to it's own Thunderbolt port instead of daisy chaining?

    No, you still cannot drive 2 Thunderbolt Displays in Windows with the MBP Retina.
    However, you can use 1 Thunderbolt display (for USB hub and LAN connection), and then use 1 Cinema display as the 2nd screen. You can chain the USB ports, but not the displays, so you do have 1 extra connection to the MBP, but that's fine.
    Windows 7 will drive this setup without problems.

  • Can I use dual monitors in Premiere Elements 10?

    I've been using Vegas Movie Studio until now. And I wonder if I even in Premiere Elements can use dual monitors. Not just to pull over the viewing part of a screen. But watch the movie in a small window on one screen with the timeline and still have the movie in full screen on the other. As this (in Vegas Movie Studio).

    Yes, you can use dual monitors with but a few little tweaks, perhaps some tweaking of the OS (what OS are you using, BTW?) and then a tiny bit of work in PrE's Workspace.
    In PrE, you will want to Undock Panel Headers, and this will allow you to drag almost all Panels, to suit your needs. Note: the Timeline's position is locked, but I think that is the only Panel, that behaves that way.
    Now, you might need to set up your display in your OS's Control Panel>Display, but that should be easy, and has probably already been done, if you were successfully running Vegas in the dual-monitor environment.
    I think that just Undocking Headers will get you where you want to go.
    Good luck,
    Hunt
    PS - others might have a few more tips for you. While I run PrPro on my dual-monitor system, I only have PrE on my laptop, and PrE has a few differences, and limitation, than does PrPro. Trust what others, like John T, Steve and Neale tell you.

  • USEING DUAL MONITORS ON MSI DKA790 GX PLATINUM WITH INTERGRATED VIDEO

    I know that you can use VGA + dvi-d port or vga + hdmi port together.But manual shows note : dvi-d connector does not support d-sub to dvi-d converter and i haven't seen a hdmi to vga converter that is not 200 Plus Dollars. Is There An easy way to get dual monitor support on the cheap? Or is It Just Easier to add another video card?

    Your going to want to just buy a video card. If you are some one who is a game you will want to go with a higher end card for instance I will use the Nvidia 8000 series. The 8200 and 8400 are lower end processors for that card while the more expenseive 8600 and 8800 are the higher end cards. Make sure they support dual out put. Make sure you have a good power supply for any of the high end cards. Some of there demands can exceed 200 watts. Most dual monitor cards will have the two DVI poets and one S-video. they will also come with adapters for HDMI and component id they support it.  I do a dual monitor display and love it. way better than the splitters. anyways hope this helps.

  • Can you use 2 Thunderbolt Displays with Windows 7/Bootcamp on a Early 2011 Macbook pro?

    Can you use 2 Thunderbolt Displays with Windows 7/Bootcamp on a Early 2011 Macbook pro?
    I have 2 and cannot seem to get them to work?

    Can you use 2 Thunderbolt Displays with Windows 7/Bootcamp on a Early 2011 Macbook pro?
    I have 2 and cannot seem to get them to work?

  • Dell Optiplex 780 standard size tower PC dual monitor display port graphic cards

    Yes, only my boss informed me that they have to be display ports, he didn't tell me why.
    I'm unable to buy from ebay or craiglist either & my local vendor doesn't have any in stock.

    Quite a mouthful I know! but I need these specific graphic cards, ideally with next day delivery:
    Dell Optiplex 780 standard size tower PC (Non SFF) dual monitor display port graphic cards
    Any recommendations? I can find 2 on amazon (UK) I need 3!
    This topic first appeared in the Spiceworks Community

  • How do I have dual monitor for different windows

    I wanted to use two monitors. One to monitor my file while the other as my working window. I am using Imac Intel Duo Core 17" and I heard that I need to buy the adapter. If I buy the adapter, what else need I click so that the FCE can be split into 2 separate monitors. Is there a function? Has anyone done this before?

    You can change this in the System Preferences>Display, but a second monitor should default to a dual monitor arrangement. You just have to drag the windows you want onto the second monitor.

  • Unable to use dual monitors in Windows 7

    I just got a T500 and am unable to use my dual monitors.  We use a docking station to hook up all of the periphals.  The VGA connector works fine.  The monitor on the DVI is not recognized.  Drivers have been updated and the monitor is operational.  I get a Generic Non-Pnp Monitor as the only choice because it is not recognizing the second monitor.  Any suggestions?

    Does the DVI cable work properly?
    I know as a fact that dual displays work on a T500 with Windows 7.
    Do you ahve the regular Advanced Mini-Dock http://www.hoathanhlaptops.com/upload/nhd_Docking%20T4xx.jpg or is it some other type of port replicator?
    Does the Monitor come with any install discs?
    Lastly, does the Monitor support both DVI and VGA?  What happens if you plug that monitor in with a VGA cable?
    T61 15.4" T9300 (2.5GHz 6MB L2) Windows 7 Professional x64 4GB Memory, NVidia Quadro NVS 140M

  • How to use an external display with Windows 7 and a Macbook Pro (Unibody)

    I just set up my new Macbook Pro 15 inch with the Windows 7 beta, and noticed that I couldn't get the external monitor to be seen using Windows 7 only. I am using my Dell 30 inch monitor and it was only seeing the laptop's main display. The fix was to download the Nvidia video drivers for the 9 series (e.g. the GeForce 9600/9400), after which it was maically able to see the display.
    The driver can be found here. Enjoy.
    http://www.nvidia.com/object/windows7overview.html

    Does Aero work?
    Maybe it will fix some of my problems:
    http://discussions.apple.com/thread.jspa?threadID=2088220&tstart=0

  • How to use Dual monitors with G5 Mac;  AND    How can the image in "Develop" be made to look like wh

    Two questions: How can I use my dual monitors on my G5 Mac?
    How can the image in "Develop" be made to look like what it will print, just as it is
    done in Photoshop with view>proof setup.

    Still wondering what tool is available in LR 1.1 to "view proof"
    As in Photoshop CS 3, and previous versions of PS, in view I can
    choose the custom .icc profile of the printer, to view what the final
    print will nearly perfectly appear like.
    What tool is available in LR 1.1 to do the same?
    Equipment: Mac OS 10.4.10; dual monitors; Epson Pro 9600 and SPR
    2400, both dedicated to matte black ink. Color working space is
    ProPhoto RGB. I stay in 16 bit.

  • How to use Dual monitors with G5 Mac;  And...    How can the image in "Develop" be made to look like

    Two questions: How can I use my dual monitors on my G5 Mac?
    How can the image in "Develop" be made to look like what it will print, just as it is
    done in Photoshop with view>proof setup.

    Patience! :)
    (This was asked and answered in previous thread.)

  • Can't use dual monitors

    I have an  HP ENVY Desktop - 700-515xt CTO.    It has 1 DVI input, no VGA input.   It has the Intel Integrated Graphic.   I want to use 2 monitors  (am using Windows 7).    I tried using a DVI to VGA dual cable, but it says the 2nd monitor is not connected to the computer.
    How can I use a 2nd monitor?
    Thanks -
    Greg
    This question was solved.
    View Solution.

    Hello @gregw54,
    I understand that you are looking to use two monitors on your desktop computer, and I would be happy to assist you in this matter!
    To ensure that your display environment is configured correctly, I recommend following the steps in this document on Using Two or More Monitors with One Computer in Windows 7.
    Please re-post with the results of your troubleshooting, and I look forward to your reply!
    Regards  
    MechPilot
    I work on behalf of HP
    Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
    Click the “Kudos, Thumbs Up" on the right to say “Thanks” for helping!

Maybe you are looking for

  • Data model: single quote in default parameter value

    Hello, when I assign a default value to a parameter in my Data model, which includes a single quote (i.e. "It's a default value"), then the single quote is escaped with a backslash (i.e. "It\'s a default value") when I open the report associated with

  • ITunes opens slow, won't sync iPad; Windows 7 64-bit

    Hello all, The issue is as follows: I try to run iTunes and it is extremely slow to open. My task manager shows an iTunes.exe process but nothing happens for about an hour.  Eventually it will open and as a music player, operates just fine.  However,

  • CURSOR IN IF Statement

    HI , I want to write a cursor in IF stmt IF NOT (( emp_rec.empno IN (9981, 9980, 9975, 9968) AND emp_rec.sal< 51)) instead of freezing the values (9981, 9980, 9975, 9968) i have taken them in a table now i want to write a cursor on the table fetching

  • Faxing from pc

    I have a brand new 8610 recently setup on the network. Ive installed the drivers/software on 5 pc's all brand new Dell 9020's running Win764. None of the pc's have the fax printer setup? As i understand it there should be 2 printers listed in control

  • Can't Install Digital Camera Raw 3.6

    I am having problems installing Digital Camera Raw 3.6. During the install, I get the message "Digital Camera Raw Compatibility Update can't be installed on this disk. This update provides support for Aperture 3 and iPhoto 9 only". I purchased Apertu