How to use HDMI input on A520

I Have an a520 i have an xbox 360 that i want to display on this PC, not sure how to display, can somebody provide specific steps on how to get the 360 to display using the HDMI input on the pC?
THanks

We purchased the hdmi adapter and were able to get audio but no video...returned it for a replacement and the same thing happened. Any suggestions? I know the hdmi cable is good because I use it with my samsung galaxy and it works fine both audio and video.

Similar Messages

Toshiba 32TL838: video flickering after fw upgrade in menus, using HDMI input

Hi,
yesterday I upgraded my 32TL838's firmware to version 6.4.0Y.1 / 94.6.27.8 using the network upgrade feature.
After the upgrade I reset the TV to start over with factory settings.
During the quick setup after the reset I noticed a very poor video quality. The whole image flickered, had a ghost effect and looked interlaced. The menus were almost unreadable.
After completing the setup the TV switched to normal TV mode (DTV cable) and at least the tv picture looked quite normal. While cable TV input is selected, I can also open menus like before, they're displayed correctly.
But as soon as I switch to HDMI input, the picture is getting nuts again, just as during the initial setup, including the TV's menu overlays. Sometimes it's getting stable for maybe 30 seconds but then it's crippled again.
Some words about my setup: the TV uses only HDMI input 1 and the cable input, nothing else is connected.
The HDMI input links to an Onkyo TX-SR508 AV receiver that is being fed by a Fantec 3DS4600 media player and BDP-S373 BluRay player.
Because I expect the what-about-your-HDMI-cabling question, I exchanged the HDMI cables but as expected that did not help at all.
At least I seem to be successful in working around the problem when using the Fantec player.
Before I upgraded the firmware I was able to use the player with 1080p/60Hz and the player was setup accordingly.
Now I switched to 1080p/50Hz and the video picture looks okay again. (However I did only a short test and as I said, sometimes_
the picture is okay for a short time.)
Unfortunately my BluRay player has no menu to change the frequency, so watching BluRay or the online services the player offers, is impossible.
So what can I do now? A firmware downgrade (if that's possible) would be a quick temporary workaround I could accept. But in the medium term I expect Toshiba to restore the features they promoted and for which I paid.
(Youtube stopped working with the old firmware and it looks as if 1080p/60Hz doesn't work anymore with the latest firmware.)
Does anybody know a way to downgrade the firmware using an USB key? I already downloaded the previuos release tl838_853886.bin but I don't have a clou how (and if) it can be installed.
Thanks for your hints
belektro

> Before I upgraded the firmware I was able to use the player with 1080p/60Hz and the player was setup accordingly.
I think you mixed simply the PAL and NTCS settings.
Usually all external players provide an option where you could choose between PAL and NTSC.
NTSC standard is the common one for countries in South / North America and Japan,
The PAL is used in Europe and some countries in Asia.
Both PAL and NTCS support 24p (24 frames per second) but most output for PAL and NTSC use interlaced frames which means that:
NTSC (60Hz) supports fps 60i or 30p
PAL (50Hz) generally uses 50i or 25p;
Probably the external player supports PAL settings and its set to 50Hz and therefore its play properly using the 1080/50Hz.

How to use Create input request Activity

Hi,
I want to get inputs from the users .
I want to display a form were user can select a input from drop down list.
That selected item i want to store it in a variable and use across the flow.
How to do that using create input request or is there any other way to do that.

You should be using "Input Request" to do what you are trying to do.
Add "Create Input Request" to your workflow
Configure the question you want the user to see in the Web Console. For example, "Select make of your dream car"
Add "questions" to your input request. For the "drop-down" selection, chose to add new question of type "Select". This will bring up the dialog box that will allow you to configure the unique ID for your question, the free form text (label) and the list of selection choices to show in the drop-down.
In the activities that follow "Create Input Request" you can retrieve the actual values that the user chose/typed by looking at the values in the [Workflow.Create Input Request.Task.Questions] table property. It has several columns: Id, Question, Value (that correspond to the fields you've configured)
If you have Input request with several questions, you can use Select from Table activity to choose the specified question (by ID) that you want the value for. If you have only one question in the input request, you can get to the value (entered by the end user) by referencing this property [Workflow.Create Input Request.Task.Questions.First Row.Value]

No sound when using HDMI input to TV

I connect Mac Book to HDMI input on TV with a mini DVI to DVI cable, to DVI to HDMI cable. Good picture through iDVD but no sound.

Yeah. It kind of *****! But it is true, HDMI does not transmit sound, just video. Which it does well I must say.
What I did is I have surround sound and I plugged a cord that has male connectors on both sides and I plugged it into my amp on one side and my mcbook on the other, so now I can get sound onto my surround sound and also get the video images on my HDTV. =) If you have a surround sound system with an amp, I would recomend doing this. Its easiest.

How to use hdmi converter make notebook video become high-definition

Yesterday, i bought a notebook. When i connect with my TV and watch video. it is not definition. I ask for my friend. he told me that get a hdmi converter from hdgenius.com and use hdmi converter make signal become hdmi,Then it will become high-definition and watch perfect video. It is OK ?

Hey there SSaccio,
I'm having a little trouble determining exactly which system is yours. The site everymac.com has a list of all standard mac products and I don't see a 2.4 G5. So the info I'm going to give you is based on the 2.3 G5 duo.
This model ( http://www.everymac.com/systems/apple/powermacg5/stats/powermac_g5_2.3dp.html )
Has the ATI Radeon 9600 with 128 MB of DDR SDRAM occupies an 8X AGP Pro slot. Dual monitoring is supported with this card up to 1920x1200. So you might be good to go with what you have already. If you know that you don't have this card, then let me know what you have and I might be able to suggest something else.
BTW
Graphics cards for Mac have a different card BIOS (or firmware, whatever it's called) than the PC versions. Therefore, you can't use a PC card in a Mac and viceversa, without reflashing it.
Nvidia, unlike ATI, does not sell their Mac cards as retail cards.
So if you don't have the ATI Radeon 9600 card then that's what you wanna get. It runs about $150-200
Cheers
-B

Having trouble figuring out how to use trigger inputs as a general purpose input.

I'm trying to use "Trigger 1" as a general purpose input to indicate the status of external circuitry. I can't seem to get the "Read High-Speed Capture Status" to indicate anything. I'm using the "Configure High-Speed Capture" VI with the capture mode set to Inverting Digital Input, and that VI feeds into a Do-While loop which contains the "Read High-Speed Capture Status" VI, which has the Ret Vect set to 0. I see from the online help that the High-Speed Capture function is available on Servo and Closed-Loop stepper systems, which I suppose is to enable the ability to read the position of the encoders. I'm using an open loop stepper system, so are these High-Speed Capture fun
ctions unavailable even though I'm looking only for status (Trigger 1), and not concerned with reading position? Thanks in advance, Rob.

Thanks for the answer Ken. I'm going to try a different workaround. The global was too slow, and I think I'll break my subVI into two parts. I'll create a sub that has all the setup stuff in it, then embed the actual "check trigger status" loop in the main VI. The loop contains only 2 or 3 nodes. Too bad LabView works this way. I can see one reason it should, but another larger reason it shouldn't. Wishlist.... Oh, speaking of wishlist, I like the improvements that 6.0 has brought, but one thing still bugs me. There's no way to have LabView remember the place to look for files when it's first started. It defaults to "My Documents", which should be, as all LabView programers know "LabVIEW6\user.lib" (or whatever). Of course, once th
ere, LabView remembers for that session. Next time it's started, back to "My Documents" again. How 'bout fixing the "Options", "Path" settings so that it will actually remember the path set? Am I missing something here, or does it have anything to do with the fact that we're using Windows 98? My buddy's using NT, and his works the same. Is there a way around this? TIA, Rob.

How to use Action/Input maps

It seems to me that the move to sharing actions menus, buttons, and other components is a logical one, given that it is desirable to have all references to the action reflect its enabled state.
The question that arises is: which ActionMap object to use as the central store? Do you create your own and pass it on somewhere?
And, if you try to do anything with homegrown InputMaps then the components stop seeing the events. I wish there was a definitive YOU MUST DO IT THIS WAY tutorial.
Why is there no factory API that can create UI components pre-attached to actions and with accelerators or mnemonics already set? Then we would not need to write half the code we do now. My solution:
public class ComponentFactory {
   ActionMap myMap;
   public ComponentFactory(ActionMap map) {
      myMap = map;
   public JButton createButton(String actioncommand) {
       Action a = myMap.get(actioncommand)
       if(a==null)
          return null;
       return new JButton(a);
   public JMenuItem createMenuItem(String actioncommand) {
    // etc...
   public void setAction(Action a) {
       myMap.put(a.getValue(ACTION_COMMAND_KEY),a);
   public void setEnabled(String actioncommand, boolean state) {
       Action a = myMap.get(actioncommand);
       if(a!=null)
           a.setEnabled(state);
}Is there any concensus as to the best way to handle ActionMaps/InputMaps?

Hugh,
>
The tutorial is a touch short on this subject, whilst
it is good on how to create and use actions with
toolbars and the like, the section on InputMaps and
ActionMaps is far too brief to get the wider picture.
The API docs on the same is about one paragraph's
worth.okay, I just checked the tutorial - it's a bit short on the inputMap/actionMap indeed.
>
You are mixing up two different issues:
a) customize a button with an action
b) bind a keyStroke to an action for an arbitrary
jComponent
a) has nothing to do with b)If b) has nothing to do with a) why have MNEMONIC_KEY
and ACCELERATOR_KEY on the action?Hmm... where do you see a contradiction to my statement? Those keys are part of a) as they are used for customization of the AbstractButtons: the button's mnenmonic/accelerator properties are set to the corresponding values of the action. This propertyChange triggers an update of the keyBinding to the button's "pressed"/"doClick" actions as registered in the actionMap. They are never used (at least not internally by Swing) for b)
Historically the action is older than the inputMap/actionMap: basically it's an ActionListener (which is more or less a command pattern) plus some (view) state. This "plus" was designed right in the beginning of Swing for a) to enable state sharing between different "buttons" but not really integrated until version 1.4. parallel to that the need for a general mechanism of binding between keyStrokes and "commands" became obvious and inputMap/actionMap were introduced in 1.3. The only action state that's needed for this mechanism to work is the enabled property. All values are ignored - so currently they somehow appear to be overloaded in the context of the inputMap/actionMap. Personally I think they are very powerful because of this extra flexibility.
>
There is still not a single diagram; and I maintain
that it is less than useful to beginners who are not
familiar with the terminology used. Well, IMO diagrams are not everything - I still think it much easier to understand than the dnd spec or the focus spec f.i.
>
you are free to use whatever object you want as akey
- write a utility method to use the name, if feellike
doeing so. There is nothing in the framework that
would single out the name as "the" key to use, The keybindings document specifically states:
"New actions can be added to a component equally
easily."
"The conventional key for an action is it's
name." If there is a conventional way then it
should be encouraged with an appropriate API. I get your point. And I definitely agree on following a convention if there is one. Except when the convention is quite immature (to formulate mildly) - and not even followed by Swing internally: most of the default actions registered in the actionMap don't even have a name, the binding is done by string literals ... duplicated in at least two places: the XXLookAndFeel and the ui-delegates.
Greetings
Jeanette

How to use the input entered in report parameters form & use it in a field in a report parameter.

Hi, I'am creating a new report, which is a combination of 'form_letter & tabular' style.
I have also created a Report Parameter with 2 inputs, that is 'to_date' & 'from_date'.
The value that will be entered in 'to_date' & 'from_date' in the parameter_form, must get displayed in the report.
So for this, I created a field for 'to_date' & added code for it in pl/sql editor.
code is as below:
function F_TO_DATEFormatTrigger return boolean is
f_to_date date;
begin
f_to_date := :PF_P_TO_DATE; // ASSIGNING VALUE TO FIELD ( f_to_date) FROM INPUT OF REPORT PARAMETER (PF_P_TO_DATE) .
return (f_to_date);
end;
BUT I'M GETTING ERROR " REP-0730 THE FOLLOWING BIND VARIABLE IS NOT DEFINED: PF_P_TO_DATE.
I tried to decode the error, but I think the problem is different. (The above code works only if "PF_P_TO_DATE" was a part of query statement, that is one of the columns in database, but PF_P_TO_DATE is a parameter). So can anybody please help me with how can I take the value from parameter input & display it on the field of the report?
Thank You.

Hi Vijetha,
Create a formula column and return the date you need and asign the formula column to a field in paper layout.
here is the example query
function CF_to_dateFormula return Date is
begin
return (:to_date); -------:to_date is that you get as a parameter
end;
Hope this will help
Regards
su.gi

Is there a way to watch VerizonFIOS cable TV on iMAC using HDMI Input?

I have a 2014 iMac. I recently moved and now have VerizonFIOS cable. The output for the cable box is HDMI. From what I can see on the back of my iMac, I have two Thunderbolt ports, and multiple USB 3 ports. Is there a way to use the HDMI cable from the cable box so I can watch TV on my iMac?

Not directly, I recommend contacting Elgato.com and see which of their products suits your needs. Apple doesn't put TV tuners in their computers, that is why you need an Elgato device.

How to use HDMI ??

Hello all,
A friend just gave me an MSI R6570 graphic card and I would like to use my LCD TV with it.
I bought an HDMI cable but nothing appends...
My TV seems to not detect the signal
Is there something to do with Catalyst Control Center for instance ??

Yes, you will need to go into CCC and set the TV as a display to be used. If memory serves me right, you right-click on the icon for the TV and can then select enable, clone, or replace. enable will use both monitors, clone will output the same exact signal (including resolution) to both, and replace will turn off your monitor and turn on the TV. If you're just wanting to watch videos or something on your TV and not using it as a dual-display setup, I would recommend replace, especially if your monitor isn't 1920x1080. Even if it is, 1080p HDTVs often aren't truely that resolution, due to overscan. You can try clone, but if it looks bad, just set the TV up as a single display and set its resolution to 1080p in the HDTV list on the resolution page of CCC.
Also, if you want the sound to be sent to your tv through the HDMI instead of coming out your computer speakers, you'll need to go to the sound options in control panel and set the default playback device to "HDMI audio out" (may be worded slightly different).

How to use simple input command ??

I am tired of trying to find an easy to understand source to implement simple INPUT command ( equivalent to cin>> and scanf() , in c++ and c as i m good in those two)
when print can be System.out.println(--) , then y does read have to be so complicated ?
Help me out guys !!!

package palindrome;
import java.io.DataInputStream;
* @author Pulkit
class Main {
public static void main(String[] args) {
int num;
System.out.println("Enter a number to check if it is palindrome");
// System.in.readline(num);
DataInputStream ob = new DataInputStream(System.in);
Now the remark line is wat i tried to do, as i thought it should follow the print method ( System.out.print ) that one.
But in a book , i see its done just the other way, just below the rem line.
I just need ur help to explain me as to how that line has been put, i.e. the syntax of that line.

How to use standard Search Input Help (return 2 data code and desc) ?

Hi,
Please advise how to use standard Input Help provided by SAP and return 2 data (code and description) ? because the standard Input Help only return the code only ?
Thank You and Best Regards
Fernand

>
Saket Abhyankar wrote:
> Hi,
>
> I think you need to go for 'Search Help Exit' or OVS.
>
> Regards,
>
> Saket.
That is not true that this is the only way. The standard Data Dictory based search help can return more than one value as long as there are multiple exporting values defined in the search help, the search help is attached to a Data Dictionary Structure, and this same data dictionary structure is used as the source of the context node. You can read more about this in the online help:
http://help.sap.com/saphelp_nw70ehp1/helpdata/en/47/9f724642314aabe10000000a42189b/frameset.htm
The Note section under Integration:
If an input help structure is stored in a field in the ABAP Dictionary, and if you want to use the field mapping of search help parameters stored in the ABAP Dictionary as the field name for the structure for your Web Dynpro input help, then map your context nodes to this structure. This ensures that all components of the structure are available dynamically at runtime as attributes of the node.
If the context node is not mapped to the structure, the data element's input help can be used if there is one.

Startrfc - how to call with "input table"?

I have not been able to get sapnwrfc for Perl to compile correctly on my AIX systems so i want to try something different.
I started to investigate using startrfc to get my data but am running in to a problem.
Problem Summary: I want to get information via RFC_READ_TABLE using startrfc. I can successfully call function modules but cannot figure out how to send in a "WHERE" clause using startrfc. Does anyone know how to send "input tables" to startrfc so that I can limit my results?
Background: I want to dump a list of the dialog UIDs in a SID/client. When I do RFC_READ_TABLE via SE37, it asks for an "OPTIONS" input table that you use to put the "WHERE" clause. I fill in the information in the "TEXT" field and all is well.
I can call startrfc with the -T option and capture the output to a file, but I cannot figure out how to use an input file to provide the OPTIONS table. -E doesn't work.
Here is what I call:
/usr/sap/<SID>/DVEBMGS60/exe/startrfc -t -3 -h <hostname> -s 60 -c 000 -l E -u <my id> -p <my password> -F RFC_READ_TABLE -E QUERY_TABLE=USR02 -E "DELIMITER=|" -T DATA,1000,w=output.txt -T OPTIONS,100,r=input.txt
My input file (input.txt) looks like:
TEXT="BNAME = 'someuid'"
Here is the error message I get when I run this.
RFC Call/Exception: SYSTEM_FAILURE
Group       Error group 104
Key         RFC_ERROR_SYSTEM_FAILURE
Message     A dynamically specified column name is unknown.
Note that I know that there are other functions to check for existence. I am attempting to get a dump of all dialog users with some information from USR02 not normally provided by the builtin function modules (ERDAT). This is just the first step to getting there. Once I have this figured out, I'll send in a "*" to match all. Also, I am able to do this sort of successfully via Perl's sapnwrfc but am unable to get it compile on AIX and that is where I need to run this.
Can anyone help?
Edited by: Eric Young on Apr 7, 2011 5:59 PM
Edited by: Eric Young on Apr 7, 2011 6:00 PM

It's fairly obtuse as well, but I can see that I'm sending something. I just don't know what it should look like so that SAP likes it. Here's the relevant send section:
000240 | 04000000 01033003 02000800 0001F400 |......0.......Ã´.|
000250 | 00000003 02030100 074F5054 494F4E53 |.........OPTIONS|
000260 | 03010330 00040000 00020330 03020008 |...0.......0....|
000270 | 00000032 00000001 03020303 00325445 |...2.........2TE|
000280 | 5854203D 2022424E 414D4520 20202020 |XT = "BNAME = 'S|
000290 | 20202020 20202020 20202020 20202020 |SOMEUID'"        |
0002a0 | 20202020 20202020 20202020 20202020 |                |
Please note that I've obfuscated "SOMEUID" and the corresponding HEX dump.
Edited by: Eric Young on Apr 7, 2011 6:26 PM

I have a late 2011 model MacBook Pro running Mountain Lion. I love the AirPlay mirroring feature with Apple TV...BUT, how do I mirror with TVs that don't have Apple TV? I used to run a cable from my mini display port to the HDMI input of a TV.

I have a late 2011 model MacBook Pro running Mountain Lion. I love the AirPlay mirroring feature with Apple TV...BUT, how do I mirror with TVs that don't have Apple TV? I used to run a cable from my mini display port to the HDMI input of a TV. This feature seems to be lost in the Mountain Lion upgrade. Did Apple feel that once Mountain Lion came out that EVERYONE would have Apple TV? There are no settings in System Preferences/Display like there used to be...only for AirPlay Mirroring.

Running a cable to the HDMI port is still supported. (and still works on mine).
If the Arrangement tab in System Preferences > Displays isn't present then it doesn't recognize the physical connection. Double check all cables. If that doesn't work try a PRAM reset:
http://support.apple.com/kb/ht1379

My HD TV has two HDMI inputs which are being used by a home theater system and my RCN cable box. i want to be able to use my appleTV as well as those but do not have another HDMI input. How can i connect it so that i can use any 1 of the 3 at any time?

My HD TV has two HDMI inputs which are being used by a home theater system and my RCN cable box. i want to be able to use my appleTV as well as those but do not have another HDMI input. How can i connect it so that i can use any 1 of the 3 at any time?

Get an HDMI switcher. Plug in the ATV directly to the TV and then use the switcher on the other input.
Example
http://www.amazon.com/Ultra-High-Performance-Switcher-Switch/dp/B0015YWKYY/ref=s r_1_1?ie=UTF8&qid=1316918064&sr=8-1

How to use HDMI input on A520

Similar Messages

Maybe you are looking for