How to use ipod shuffle?

How to use ipod shuffle?

http://manuals.info.apple.com/MANUALS/1000/MA1550/en_US/iPod_shuffle_4thgen_User _Guide.pdf

Similar Messages

  • How to use iPod Shuffle with external Speakers

    I tried using iPod Shuffle but its not working with external speakers.
    Please let me know if there is any way i can use it in External Speakers

    http://manuals.info.apple.com/MANUALS/1000/MA1550/en_US/iPod_shuffle_4thgen_User _Guide.pdf

  • How to use iPod Shuffle Correctly in ur PC's?

    hi!
    Using the latest Versions:
    iPod Updater 2006-03-23
    iTunes 6.0.4.2
    * Be sure to meet the System Requirements b4 installing.
    Install, then reboot.
    Follow these steps correctly to make your iPod shuffle last long.
    To RECHARGE your iPod (not syncing/erasing songs, just recharging) using ur PC's USB correctly:
    1. Run d iPod updater, wait for 5-10 sec before connecting your iPod shuffle, then let it recognize your iPod,
    2. Let the iPod updater running as long as you want to recharge your iPod Shuffle
    3. If ur iPod shuffle is already fully charged or if you want to stop d charging process, then
    4. Use the Safely Remove Hardware, Stop d USB Mass Storage Device,
    5. Then close the iPod updater
    To SYNC/ERASE songs in iPod Shuffle correctly:
    1. Run iPod updater, wait for 5-10 sec then connect your iPod shuffle
    2. After it recognizes the iPod, wait for 5-10 sec then run iTunes
    3. The iTunes will not recognize the iPod shuffle.
    4. Close the iPod updater, iTunes will now recognize the iPod shuffle
    5. You could now sync/erase your songs.
    * This is for Windows users, don't know if it's the same with MAC users.
    ** These steps are only for those iPod shuffles that can still be recognize by ur PC's.
    If ur iPod shuffles can't be recognize by your PC's,
    * "Can't be recognize"
    Not showing Safely Remove Hardware in your toolbar,
    USB Mass Storage Device in your device manager, and
    New Drive in My Computer or Windows Explorer
    Maybe it's Battery empty:
    Use the seperate AC Plug Charger,
    fully charge it, then follow all my steps.
    * I think the latest iPod updater program conflicts with the latest iTunes program:
    Coz, if you just connect your iPod shuffle and let the iTunes run automatically, the iTunes will recognize it while the Windows will recognize it for just a sec then disconnects it, that's why you couldn't sync/erase yor songs.
    You could only Sync/Erase ur songs for the 1st time you connect your iPod Shuffle, the next time you'll Sync/Erase it will show an error message "Disk write error" something like that, coz the windows already disconnected it.
    I hope this would all help you!..
    -jmcobra23-
    Philippines
    AMD Sempron 2200 ECS L7VMM3 3.0a Mobo   Windows XP Pro   Dual OS ME/XP Pro SP2 MCE 2005 R2

    This is what I have figured out.
    I have my (60G video) iPod configured with Windows. I can now still add new MP3 files from both my PC and my Mac. I can also add movies (my own, purchased by me, used ONLY on my own iPod) converted with a special program.
    The only thing I miss is the games that I purchased through apple (solitaire and a few others).

  • How to use iPod shuffle in the car. What cable should I use

    When I connect my shuffle to car.  It says ipod authorization failed. What can I do now?

    If you are talking about a small, 3.5mm round hole, which looks like a headphone jack, it will accept any standard audio input. This is standard on all Seats.
    Many companies label these as "mp3 port" or "aux-in" because it sounds cooler and more "sophisticated".
    Just use a standard 3.5mm to 3.5mm audio cable.
    From http://www.seat.co.uk/
    "The Seat is available with either a connection which allows an iPod to be integrated into the vehicle or a special connection for all USB memory devices and MP3 audio players with a USB port. _There is also an Aux-in audio connection as standard, which allows external audio sources to be plugged into the standard headphone socket and the sound played through the vehicle's speakers_."

  • Hi my name is Vajra from INDIA, i am using ipod shuffle 3rd generation but it is not working properly due to battery problem, i need to change the battery please guide me how to change the battery or any chance to replace the ipod shuffle 3rd generation ?

    Hi my name is Vajra from INDIA, i am using ipod shuffle 3rd generation but it is not working properly due to battery problem, i need to change the battery please guide me how to change the battery or any chance to replace the ipod shuffle 3rd generation ?

    Seems no one care about us .no one replied till no@!!!!@ strange

  • How to put IPOD Shuffle I into Disk Mode ?

    How to put Ipod Shuffle I into diskmode ?

    When connected, in iTunes click on shuffle icon in Devices, then click on Settings tab. Scroll down and click the square in front of "Enable disk use", the adjust slider for amount of flash memory to reserve for data. Click Apply, and you're done!
    When you use iPod shuffle as a disk, the status light on the front of iPod shuffle blinks orange continuously, and the iPod shuffle disk icon appears on the desktop on the Mac, or as the next available drive letter in Windows Explorer on a Windows PC. Drag files to and from iPod shuffle to copy them.
    Ejecting iPod shuffle Important: If the iPod shuffle status light is blinking orange, you must eject iPod shuffle before disconnecting it from your computer. If you don’t eject iPod shuffle before disconnecting it, you could damage files on iPod shuffle.
    To eject iPod shuffle:
    Click the Eject (C ) button next to iPod shuffle in the iTunes Source list. If you’re using a Mac, you can also eject iPod shuffle by dragging the iPod shuffle icon on the desktop to the Trash.
    If you’re using a Windows PC, you can eject iPod shuffle by clicking the Safely Remove Hardware icon in the Windows system tray and selecting your iPod shuffle.

  • My computer doesn't recognize my "used" ipod shuffle

    How do I get my computer to recognize my "used" ipod shuffle?

    See how easy it was to state those important facts.  My mind-reading superpower is not working this week... 
    I know how to connect to the UBS port correctly
    I wasn't talking about the USB port end of the cable.  I was talking about the plug that connects to the headphones jack on the shuffle.  That connection can initially be tighter than expected for some people, so make sure it is fully inserted into the headphones jack.  You should feel it click into place.
    I have one short cable and a cable with a port to dock the shuffle. (it lights up)
    If that second one is a third-party cable, make sure it is described as being for the 3rd and 4th gen shuffle.  A cable that is for the older 2nd gen shuffle does not work, because the connector plug is different.  So, it's possible that you have only one cable that is designed to work withe the 4th gen shuffle?
    Both my shuffles are brand new from Amazon. (I returned one as I thought it was bad)
    IF you returned one of the shuffles, you only have one on-hand to trouble-shoot with at the moment?  "3 bad iPods"?  What model is the third iPod?  It doesn't connect to your computer and iTunes either?  Or maybe you are saying you had three shuffles total and returned one, so now you have two?  Confusing...
    It seems unlikely that you'd get three (or even two) shuffles that do not connect consecutively.  So it still seems to me like it's related to software on the computer, IF it's not one of the things mentioned above.  This document has advice on things to try, when both the computer (Windows) and iTunes do not recognize the shuffle as being connected
    http://support.apple.com/kb/TS1369
    Some of the points you have already tried, and some do not apply to the shuffle.

  • Playlist shuffle is working even when the button is off...Im using Ipod shuffle 4th gen*

    Im using Ipod shuffle 4th gen...And I am not able to stop the songs getting shuffled....For example I want my ipod the play the songs one by one...but its not working...Its shuffling songs by default...I mean the button which stops shuffling the songs(the on off button when placed in the iddle stops shuffling songs) is NOT working....What to do?

    If you are trying to play a playlist in the order shown for that playlist (in iTunes), you need to be IN the playlist on the shuffle.  You may be in the main "all songs" list on the shuffle, and not a particular playlist.  Note: You can have multiple playlists on 4th (and 3rd) gen shuffle, which is why there is a separate "all songs" list.
    This article explains how to use VoiceOver, including how to change between playlists.
    http://support.apple.com/kb/HT4322
    (See Changing playlists and To choose an item from the playlist menu.)

  • Using iPod shuffle 4th generation for first time and receiving the error : one of the USB devices attached to this computer has malfunctioned, and windows does not recognize it. For assistance in solving this problem, click this message

    Using iPod shuffle 4th generation for first time and receiving the error : one of the USB devices attached to this computer has malfunctioned, and windows does not recognize it. For assistance in solving this problem, click this message.
    Using win 7 and latest iTunes [10.6.3]. Have already gone through below links and did not find any solution.
    http://support.apple.com/kb/HT2292
    http://support.apple.com/kb/TS1369
    http://support.apple.com/kb/HT1923
    http://en.kioskea.net/forum/affich-17997-ipod-not-detected

    I was hoping it would be something like a USB device conflict, but now the shuffle is the only thing connected...
    This article was one of the ones you linked to above in your initial post
    http://support.apple.com/kb/TS1369
    Under Part 9. Verify that USB drivers are installed, did you try the steps in If only "Unknown Device" appears?  That appears to be your situation.
    Also, you said that the shuffle initially worked well enough to do a sync, then it had the same problem again.  If you can get it to work again initially, before doing anything else, try the following.  Select the shuffle in the iTunes sidebar, under DEVICES.  Over to the right, go to the Summary tab.  By default, the checkbox for Enable disk use should be unchecked.  If so, check it and Apply the change.  See if that makes any difference. 
    (If Enable disk use was already checked, try unchecking it and Apply the change.  Basically, set it the "other way" and see if there is any improvement.)
    NOTE:  When disk use is enabled, you have to eject the iPod in iTunes before disconnecting it physically.
    If the disk use change makes a difference, that may provide a clue about the actual cause.

  • I pay to learn how to use iPod Nano

    hi,
    i am looking for someone to teach me how to use ipod nano urgently. willingly to pay. 1 hour. location - clementi. pls email me at [email protected] with your contact number and leave. thank you.

    Go to http://www.apple.com/retail/
    Find the closest Apple store and click on the link.
    Look under Calendar of Events.
    There is a free iPod and iTunes Workshop 4 times a week
    “Explore iTunes for Mac and Windows and learn why it is the best digital jukebox with the #1 music store inside. You'll learn to import and organize your music, burn CDs, buy music or audiobooks from the iTunes Music Store, create playlists, and share your music. And with iPod, you can take your favorite music and even photos with you wherever you go.“

  • I can't get my new (used) iPod shuffle to appear in My Computer or iTunes Devices

    I can't get my used iPod shuffle to appear in My Computer or iTunes Devices.  Any ideas?

    Which iPod shuffle model is it?  This article about syncing the shuffle shows the four types.
    http://support.apple.com/kb/HT1719
    As a test, you can try shutting down (powering off) and disconnecting all USB devices (including hub).  Start it up with only standard keyboard and mouse connected (if it's not a laptop).  Run iTunes.  Connect shuffle to a direct USB port.

  • Used ipod Shuffle

    I recently got a used ipod shuffle, legally I might add. I was wondering if there was any way to keep some of the songs that are already on there and add some songs of my own? Thanks for any information.

    i seen you are a windows user try this software. iPod2pc download it here http://www.casicakes.com/ it will move all your music on the ipod to your MY MUSIC Folder. I used this program with after my computer needed reinstalled and it worked a treat at getting my music back.

  • HT1447 how to fix ipod shuffle 4th generation when frozen?

    I don't know whats wrong with my ipod shuffle 4th generation. It's not working.

    Instead of "charger," you should call it the "USB cable" to avoid confusion.  When started reading your post, I was thinking, how can your son break a USB power adapter (the "charger" that plugs into a wall socket) by biting it...
    Since you got the product with the two USB cables at the Apple Store, you have the right replacement (some third-party replacements are for the 2nd gen shuffle and do not work with the 4th gen shuffle).  Make sure you are completely inserting the plug into the headphones jack.  The fit may be tighter than expected, since the connectors are new.
    http://support.apple.com/kb/TS3572
    If you tried both of those cables, it would be unlikely that you got two faulty cables in one package.  If a new USB device has been added to the computer between the time it worked with the old cable and now, there could be a problem on the USB bus (such as not enough power or a device conflict). 
    As a test, you should shut down (power off) the computer and disconnect all USB devices (including any hub), except for standard keyboard and mouse (if used).  Do this to reset the shuffle
    http://support.apple.com/kb/ht1655
    Start up computer, run iTunes, and connect the shuffle by itself to a direct USB port on the computer.

  • ITunes has stopped Working when using Ipod shuffle 3gen on Windows Vista HB

    Itunes keeps shutting down when I insert my Ipod shuffle into the usb connection of my latop. I am using a Windows Vista Home Basic for an OS.
    Not sure if this is a Vista, Apple issue, or something else...
    I have contacted apple about this and uninstaled/reinstalled Itunes. Yet after all this, I get the same error message. The message reads:
    "iTunes has stopped working. A problem caused the program to stop working correctly. Windows will close the program and notify you if a solution is available."
    As far as I know Vista should be compatible with iTunes and it is until I actually try to use my shuffle (newest model). Its weird because my shuffle works fine on a second computer that has Windows XP for an OS...
    Does anyone have a solution to this??
    Thanks in advance!

    i have the same issue... but i found a workaround.. i tried 3 diff OS's . didnt change the problem. To Add apps or music to ur Ipod... simply DISCONNECT the Ipod from the PC then add files/folders to library. Then connect the ipod back to PC and sync. it has no problem adding the files that way (at least in my case) I hope this helps... Good Luck =)

  • How to use ipod w/ more than one computer

    I am new to ipod. I set it up on my laptop, and have all uploaded my cds to my ipod from there. I do nat have internet at home, so tried using my parents computer. How do you use the ipod with another computer that doesn't have all your songs on it? When I go to sync it, it ask if i want to delete all my ipod songa and replace with the ones on the other computer. I am trying to get album artwork. What am I not doing right?

    If you want to connect and use an iPod on more than one computer or with more than one library you need to change the update preference in the iPod Summary tab to "Manually manage music and videos" and click Apply. The content of iTunes and the iPod are not syncronised in this mode so the two can be different. You can directly access the content of the iPod and play it through iTunes and you can drag and drop whatever you want to the iPod from either library. Even when manually managing an iPhone, you can only add content from one iTunes library.
    Using iPod with Multiple computers
    Managing content manually on iPod and iPhone
    Syncing Music to iPod
    Something else to be aware of when using an iPod in manual mode is that the "Do Not Disconnect" message will remain on the display until you physically eject the device: Safely Disconnect IPod
    You can use a keyboard command to prevent your iPod auto-syncing with iTunes. While connecting the iPod to the computer on Windows hold down the Shift + Ctrl keys together. This will stop the iPod from auto-syncing with iTunes and the iPod will appear in the source list. Wait until you are sure the iPod has mounted, and that it will not auto sync and then you can let the keys go. This may take between 20 to 30 seconds depending on your computer: iTunes - Keyboard Shortcuts for Windows
    When your iPod appears in the iTunes source list change the update setting to manual, that way you can continue to use your iPod without the risk of accidentally erasing it.

Maybe you are looking for

  • Staffing changes and how to handle within the middle of a project

    Hello, Our users have this issue.  They have a project set up that is partially complete.  Let's say the project lasts three years and we have finished half of the project.  We have a resource staffed to a role that has been listed as the responsible

  • External Hard Drive doesn't have the marked space

    I just got a new external hard drive from Western Digital which is supposed to have 250 G of space in it. I've had external drives before and they always had a few mbs missing when I open the file which I always assumed was formatting or some other n

  • JPA Weird Transaction error ... ?

    Hi All, For this code i am getting a weird exception which follows the code block.. i have started a Transaction but still openjpa gives this exception   public static void deletePort(String port){        BcsPort bPort=em.find(BcsPort.class, port);  

  • Time Zone Problem in Crystal Reports

    Hi, I have this question and hope someone can advise. I have designed reports(using crystal reports version 10.5) in India and scheduled it to run in a server in Singapore. In the report, I have a special field Print date at the footer of the report

  • Canon Pixma MP610 fails to print and returns a " Stopped - 'Filter' failed" error message.

    Hi, I have updated to latest OS and now my Canon Pixma MP610 fails to print and returns a " Stopped - 'Filter' failed" error message. I am running OS X 10.9.3 (13D65) on a 3.4 GHz Intel Core i5 iMac with  8 GB 1600 MHz DDR3 I've done a complete syste