How to use labview program receive arduino 2560 mega digital sigal

Dear sir,
i use arduino mega 2560 connected to labview.
i don't have idea to sketch the labview program receive arduino digital signal, pl help.

NapDynamite wrote:
Check for following niches:
1. Check whether the COM port you have selected is correct.
2. Check whether your arduino is loaded with LIFA firmware.
The error wouldn't be with not loading the LIFA firmware it is "Insufficient location information or the device or resource is not present in the system." So I'm going to guess that COM5 doesn't exist.
Click the little arrow next to COM5 and it will list the COM ports that LabVIEW (and MAX) see and can use.  If yours isn't listed you'll need to figure out why.  If none are listed then you likely don't have VISA installed.
Unofficial Forum Rules and Guidelines - Hooovahh - LabVIEW Overlord
If 10 out of 10 experts in any field say something is bad, you should probably take their opinion seriously.

Similar Messages

  • I need to program a Hittite Fractional​-N Synthesize​r Evaluation Kit with a HMC702LP6C​E an external YIG oscillator​. Not sure how to use Labview to control the PLL.

    I need to program a Hittite Fractional-N Synthesizer Evaluation Kit with a HMC702LP6CE an external YIG oscillator.  Not sure how to use Labview to control the PLL.

    Here is how to use the PLL. But I don't know of how to interact with that device
    http://zone.ni.com/devzone/cda/tut/p/id/3781
    And for thouse who don't know what a PLL is a free bonus link is here:
    http://digital.ni.com/public.nsf/allkb/07BC8D77D4E​9AE258625708B007CE74F?OpenDocument
    and a second one on what that device is: http://www.hittite.com/products/view.html/view/HMC​702LP6CE
    Now we are all caught up to speed.
    Sam S
    Applications Engineer
    National Instruments

  • How to make labview program to get average value of 200 reading from multimeter (by using loop)

    Hello
    How to make labview program to get average value of 200 reading from multimeter (I using using loop) to read voltage from mulmeter  but I like to get average value of all of 200 reding how can I do that?
    Thanks
    Wee
    Solved!
    Go to Solution.

    Another idea with less programming - take advantage of the "free" array that comes with a Chart - i.e. the  History Data.
    1) Wire your DMM data to a Chart. (You can set the chart to invisible if you don't plan on using it in the GUI).
    2) Set the Chart History Length to 200 (right click on the chart, click on Chart History Length...)
    3) On the block diagram, use the History Data Property Node, wire it to Mean.vi, and you're done.
    Easiest running average ever.
    Message Edited by Broken Arrow on 04-07-2010 11:36 AM
    Richard
    Attachments:
    EasyAvg.jpg ‏8 KB

  • How to open labview program with Quit Labview function inside?

    Hi Any idea how to open labview program with  Quit Labview function inside?
    I forgot to add and set the condition of the type for this program.
    If the program is an application, it would close straight away.
    If it is still labview work, it will go straight to editing program without closing.
    So I need to recover, open it and make some changes.
    Clement
    Solved!
    Go to Solution.

    Put the VI in a project and open it from there, then it shouldn't autorun. You can use App.kind property of application to decide whether to close or not.
    /Y
    LabVIEW 8.2 - 2014
    "Only dead fish swim downstream" - "My life for Kudos!" - "Dumb people repeat old mistakes - smart ones create new ones."
    G# - Free award winning reference based OOP for LV

  • How to use labview with the handyboard

    Hi,
    how to use labview with the handyboard
    Thx...

    I'm assuming you're talking about this, since you didn't provide a link for those of us who don't know what you're talking about.
    As the other poster said, you didn't say how you want to use LabVIEW with it.  If you want to write LabVIEW programs than run on the microprocessor, then you're out of luck.  If you want LabVIEW to interact with it, then you've got a couple of options, SPI probably being the best, but it also has DI and AI that you could use to communicate with it - the DI's could be used as a parallel interface.
    Message Edited by Matthew Kelton on 12-17-2007 02:21 PM

  • How to use LabView to control Primera Bravo II CD burner?

    I am trying to use LabView to control the Primera Bravo II CD burner and label printer. The software that controls the Bravo II is PTPublisher. How to use LabView to communicate/control the PTPublisher? Please help, Thanks

    Hi Qian,
    I installed PTPublisher on a virtual machine, and I was wondering what kind of tasks you wanted to control within LabVIEW.  From the program GUI, it appears like the only way to access functions is via mouse clicks.  Do you know of any other way to control the Bravo II CD burner besides the PTPublisher software?  If not, does the PTPublisher allow you to control it in some way other than clicking?
    Peter K.
    National Instruments

  • How to use LABVIEW to collect wireless network camera (with video server) video.

    How to use LABVIEW to collect wireless network camera (with video server) video.I would like to use LABVIEW for a wireless network camera (IP Camera comes with the video server module)the client program.Will the ability to achieve?If feasible, how to do, there are examples, thank you.

    I believe NI Vision is what you are looking for. 

  • Can any one please tell me how to write labview program for data logging in electric motor bike.

    Can any one please tell me how to write labview program for data logging in electric motor bike. I am going to use CompactRIO for getting wide range of data from various sensors in bike. I need to write labview program for data logging of temperature, voltage and speed of the bike. Can any one help me?

    Yes, we can.   
    I think the best place for you to start for this is the NI Developer Zone.  I recommend beginning with these tutorials I found by searching on "data log rio".  There were more than just these few that might be relevant to your project but I'll leave that for you to decide.
    NI Compact RIO Setup and Services ->  http://zone.ni.com/devzone/cda/tut/p/id/11394
    Getting Started with CompactRIO - Logging Data to Disk  ->  http://zone.ni.com/devzone/cda/tut/p/id/11198
    Getting Started with CompactRIO - Performing Basic Control ->  http://zone.ni.com/devzone/cda/tut/p/id/11197
    These will probably give you links to more topics/tutorials/examples that can help you design and implement your target system.
    Jason
    Wire Warrior
    Behold the power of LabVIEW as my army of Roomba minions streaks across the floor!

  • How to use (to program) a Scheme in Xcode? (novice programer needs help!)

    How to use (to program) a Scheme in Xcode?
    i have been using Aquaemacs (GNU emacs) with Guile extensions. but i really would like to do all that in Xcode. is it possible? thanks.

    I believe that Scheme is not a language natively supported by Xcode. Maybe there is a way to write a plugin for it, but I don't really think so and in particular I haven't seen one for LISP or Scheme.

  • How to use labview with gpib to connect with Agilent PNA E8362B ?i am newbie ..just started to work on labview about a fortnite bck and a novice in interfacing skill ..so plzzzzz explain me in a litle detail

    how to use labview with gpib to connect with Agilent PNA E8362B ?i am newbie ..just started to work on labview about a fortnite bck and +i am a novice in interfacing(networking... jst know tidbits) skill ..so plzzzzz explain me in a litle detail

    Sir
    We were able to solve that problem...but now could you advice as to which DC power supply we should use (preferably avalable in India) so that it can be controlled by Labview (through a gpib/rs232/any other port) to give a square wave of desired frequency/other parameters.
    Regards
    Shivam

  • How to use labview with gpib to connect with Agilent PNA E8362B ?

    how to use labview with gpib to connect with Agilent PNA E8362B ?i am newbie ..just started to work on labview about a fortnite bck and +i am a novice in interfacing(networking... jst know tidbits) skill ..so plzzzzz explain me in a litle detail

    Duplicate Post.

  • How to use the program RHMOVE30

    Dear Gurus,
    One of our consultant has created organisation structure in one client of development system and wants to transport the same to another client in the same system and also to another system Quality.
    Came to know that by using program RHMOVE30 it can be done, but can anyone tell me how to use this program, I mean what are the inputs to be given and how to get the transport request.
    Regards,
    Sharath

    Hi Ali,
    Yes, normally transports will be moved from DEV to PRD and hope the same configuration is there in u r setup. But if you want to move the transport from PRD to DEV there is a way, but for this you may need to open the client restriction in u r production system (which is not recommended or u have to do this when no user is logged on to the production system).
    First make changes in the client settings for enabling transport request generation and execute the program RHMOVE30 and give u r inputs and generate a transport request. Once the request is generated it wil create two files(cofile and datafile folders) in trans folder (/usr/sap/<SID>/trans or <drive>:\usr\sap\<SID>\trans)
    Based on the request number copy the cofile and data file from production system and paste it in the same path in development system. Then login to development system from SAP and go to the import queue of development server and then choose EXTRAS->OTHER REQUEST->ADD and this will add that request to development queue and u can transport it normally.
    Hope this clarifies. Award points if helpful
    Regards,
    Sharath

  • How to Use LABVIEW charts with Mathscript

    Hi,
       I recently tried to work on Mathscript and it is really amazing. what I tried to figure out is:
        Instead of plotting using traditional "plot" statement, how to use LabVIEW chart ( I know how to Add output but the graph were not as expected
    Is there any mean to get rid of this "Lengthy" delay that "ALL MATLAB User know" for first time compilation?
    Thanks in advance
    Waleed El-Badry MSc.,MCPD, ISTQB Certified Tester
    Assistant Lecturer
    Mechatronics Department
    Faculty of Engineering
    Misr University for Science & Technology

    Well Chris,
             I was about to post the solution, but as I said, I'm in a middle of experts
    It took me 3 hours to figure it out. I should've checked your answer . I resolved to the same suggesstion of yours. I only added some functionality to get the newbies like me being acquainting with how easy to work with LABVIEW mathscript based on MATLAB knowledge.
    Waleed El-Badry MSc.,MCPD, ISTQB Certified Tester
    Assistant Lecturer
    Mechatronics Department
    Faculty of Engineering
    Misr University for Science & Technology
    Attachments:
    Play with Mathscript.vi ‏35 KB

  • How to use the program called ZSAPLINK to import Function Name

    How to use the program called ZSAPLINK to import Function Name

    Not sure why you posted into this forum?
    Note the header for this forum:
    This forum is dedicated to all other development-related questions which are not directly addressed by other forums. This includes Business Objects SDKs, products, or technologies which do not fall under BusinessObjects Enterprise, BusinessObjects Edge, Crystal Reports Server, or Crystal Reports (for example Desktop Intelligence SDK, Universe Designer SDK, Portal Integration Kits, Java User Function Libraries, and other third party technologies or development languages).
    Ludek

  • How to use JavaMail to receive incomming email?

    Hello,
    I am a year 3 student and doing a final year project about web hosting.
    I want to know how to use JavaMail to receive and treat the incomming email. It means that the incoming email how to process and store the "message" in the recipient "folder" in the "store" class.
    If you have any optinions or examples or suggestion, please contact me.
    Thank you for your attention....

    First, it would be better to post questions about JavaMail in the JavaMail forum and not in the JSP forum.
    Second, the JavaMail download comes with a set of examples, including some that cover exactly what you ask.

Maybe you are looking for

  • Macbook Air mid-2013 suddenly not booting - showed battery icon then died

    Hi all, This morning, I used my Macbook Air (mid-2013) to send an email and check up on my usual stuff, nothing I've not done hundreds of times. I then closed the lid and went to work. Again, nothing I've never done before. When I got home though, I

  • "Bad parameter" when starting Acrobat XI Pro (Windows 7 Pro 64-bit)

    The first time I start Acrobat XI Pro each day (whether directly by clicking on the Acrobat icon or indirectly by clicking on a PDF file), I receive a "bad parameter" screen and I can't go any farther with the program. At that point, I close Acrobat.

  • Satellite A130 -ST1311 PSRD6U - How to delete BIOS password

    Toshiba Satellite A130 -ST1311 PSRD6U-01500JB English with translator: When enabling: Enter Password [ ] I did not put password on bios. My computer has a proprietary information. Now I must send my laptop in service centre? If problem with Flash BIO

  • Portal language

    Hi, We're using the CE Portal as a demo system here. It's linked to R3 for the users, etc. The language both normal and in default settings in SU01 on R3 is English. On the portal, most of the pages display in English, however the header and the menu

  • 'Call Transation  ___  Using bdcdata_tab' regarding

    Dear Experts, I am working on the subject code. The selection/parameter values are successfully passing to the screen (IW28), but the program takes to the first screen instead of executing directly. Please guide. kind regards Jogeswara Rao