How to verify ISAKMP Aggressive mode using show command only?

How to verify ISAKMP Aggressive mode using show command only?

Ah OK, my mistake. I was thinking ASA - I believe you are using an IOS-based VPN.
The state after establishment should be "QM Idle" (quick mode) - whether the Phase 1 was MM or AM.
I think you'll only see the AM in the debugs (like you have) or if you watch the output of the "show cry isa sa" command during establishment of the Phase 1 SA. If you're quick, you may see it cycle through as shown in this reference:
http://www.cisco.com/c/en/us/td/docs/ios-xml/ios/security/s1/sec-s1-cr-book/sec-cr-s3.html#wp5743341910

Similar Messages

  • How can I check the virtual-address up using show command in ACE?

    I want to check the virtual-address using show command.
    however, there are not in ACE. So I used the ping to check virtual-address status in ACE
    I want to know the command what is verify virtual-address status , using show command
    Thank :)

    Try -> show arp
    There you have a Type column and a Status column.
    Look for the entry "VSERVER" in the Type column
    Roble

  • At CRS-1,how can i use show command with pipe | ?

    HI,ALL
    when I use show command with pipe on the CRS-1,the command invalid
    RP/0/RP0/CPU0:JA-DL-CR-1.MAN.CRS-1#show interfaces | include line |errors 
                                                                       ^
    % Invalid input detected at '^' marker.
    ========================================================
    But Previously on the cisco 7609,I can use the show command
    GZ-DM-SR-1.MAN.7609#show int | include line |err
    Vlan1 is down, line protocol is down
         0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored
         0 packets output, 0 bytes, 0 underruns
         0 output errors, 0 interface resets
    Vlan11 is administratively down, line protocol is down
         0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored
         0 packets output, 0 bytes, 0 underruns
         0 output errors, 0 interface resets
    Vlan99 is down, line protocol is down
         0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored
         0 packets output, 0 bytes, 0 underruns
         0 output errors, 0 interface resets

    RP/0/RP0/CPU0:JA-DL-CR-1.MAN.CRS-1#show interfaces | include line |errors 
                                                                       ^
    % Invalid input detected at '^' marker.
    RP/0/RP0/CPU0:JA-DL-CR-1.MAN.CRS-1#show interfaces | include line |?    
    | 
    RP/0/RP0/CPU0:JA-DL-CR-1.MAN.CRS-1#show interfaces | include line | |?
                                                                        ^
    % Invalid input detected at '^' marker.
    RP/0/RP0/CPU0:JA-DL-CR-1.MAN.CRS-1#show interfaces | include line | ?
      begin    Begin with the line that matches
      exclude  Exclude lines that match
      file     Save the configuration
      include  Include lines that match
      utility  A set of common unix utilities
      <cr>    
    RP/0/RP0/CPU0:JA-DL-CR-1.MAN.CRS-1#show interfaces | include line |
    % Incomplete command.
    RP/0/RP0/CPU0:JA-DL-CR-1.MAN.CRS-1#show interfaces | include line |errors
                                                                       ^
    % Invalid input detected at '^' marker.
    RP/0/RP0/CPU0:JA-DL-CR-1.MAN.CRS-1#                                     
    RP/0/RP0/CPU0:JA-DL-CR-1.MAN.CRS-1#show interfaces | include line | ?   
      begin    Begin with the line that matches
      exclude  Exclude lines that match
      file     Save the configuration
      include  Include lines that match
      utility  A set of common unix utilities
      <cr>    
    RP/0/RP0/CPU0:JA-DL-CR-1.MAN.CRS-1#show interfaces | include line |?
    | 
    RP/0/RP0/CPU0:JA-DL-CR-1.MAN.CRS-1#show interfaces | include line | include er$
    Thu Jan 15 22:36:24.120 GMT
    RP/0/RP0/CPU0:JA-DL-CR-1.MAN.CRS-1#
    RP/0/RP0/CPU0:JA-DL-CR-1.MAN.CRS-1#show interfaces | include line           
    Thu Jan 15 22:37:05.013 GMT
    Loopback0 is up, line protocol is up
    Loopback1 is up, line protocol is up
    Loopback6 is up, line protocol is up
    Null0 is up, line protocol is up
    POS0/0/0/0 is up, line protocol is up  (APS not Configured )
    POS0/0/1/0 is up, line protocol is up  (APS not Configured )
    TenGigE0/0/4/0 is up, line protocol is up

  • How to get Systemstate Backup size using PowerShell command in Windows 2008 R2

    Hi,
    We using WBSummary command to get completed backup status.
    I need to find how much data is backed up  using powerShell command .
    Is there any way to get the details , i can see the GUI but no in command.
    Please advise
    Regards Gopi K

    Hi,
    You mentioned that you can see the system state backup size in the GUI. Does the backup size mean the amount of date transferred?
    It seems that there is no such a PowerShell to get Systemstate Backup size. You may need to you need a PowerShell scripts to do this work.
    http://social.technet.microsoft.com/Forums/windowsserver/en-US/home?forum=ITCG
    Regards,
    Mandy
    We
    are trying to better understand customer views on social support experience, so your participation in this
    interview project would be greatly appreciated if you have time.
    Thanks for helping make community forums a great place.

  • How to load the boot menu using the command line , after the configuration change ?

    how to load the boot menu using the command line , after the configuration change ?

    Hi @Bask-48 
    Welcome to the HP Forums!
    It is a terrific place to find answers.
    For you to have the best experience in the HP forum I would like to direct your attention to the HP Forums Guide Learn How to Post and More
    I grasp you are trying to change the boot order.  Here is a link to Configuring the Boot Order in the System BIOS
    that will assist you.
    Good Luck and Happy Holidays!
    Sparkles1
    I work on behalf of HP
    Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
    Click the “Kudos, Thumbs Up" on the bottom right to say “Thanks” for helping!

  • How much power is Sleep Mode using?

    I use my PBG4 as a desktop, with the power plugged in. I love using sleep mode so it'll come back on almost instantly, but I'm wondering how much power I'm actually using (read: "wasting").
    Is it so miniscule that my environmentalist conscience can justify leaving it in sleep mode overnight? Inquiring minds want to know.
    /tw

    According to this Apple PDF: Apple Product Environmental Specification - Powerbook G4 12", the PB draws about 3W while asleep and plugged in, about 20W when awake and idle and about 2W when turned off and plugged in (battery charging).

  • How do I create a partition using diskutil command

    I've shrunk my original partition and now filevault2 has converted it to corestorage, as follows:
    $ diskutil list
    /dev/disk0
       #:                       TYPE NAME                    SIZE       IDENTIFIER
       0:      GUID_partition_scheme                        *500.1 GB   disk0
       1:                        EFI                         209.7 MB   disk0s1
       2:          Apple_CoreStorage                         315.3 GB   disk0s2
       3:                 Apple_Boot Recovery HD             650.0 MB   disk0s3
    Now Disk Utility tells me it won't create any new partitions, and to use the command line "diskutil". I guess it doesn't work with anything other than HSF or FAT.
    But, reading "man diskutil" reveals no command option to add an individual partition. Can someone help .. what is the option to add an additional partition without disturbing the others? As I read it, partitionDisk and splitPartition are both destructive. I see that resizeVolume is non-destruction, but I'm fearful of making any changes to the 4 existing partions, since they're all System partitions.
    And, while I'm asking, I also don't see any remove option listed .. maybe mergePartitions, but again, I'd be reluctant to merge something into one of these system partitions for fear of killing it?
    regards,
    Paul

    AFAIK, you have to turn off FV2, restart, and then repartition. But, that's just a WAG.

  • How do we refer Sub directories using UTL_FILE command

    Hi Gurus,
    I have created a DIRECTORY My_project using CREATE DIRECTORY COMMAND. This directory is linked to my OS D:\My_project folder.
    There are several sub directories under My_project folder such as D:\My_project\Outfile folder which I would like to refer while using UTL_FILE command to process files.
    When I try to run the following PLSQL
    DECLARE
    out_file utl_file.file_type;
    l_line VARCHAR2(100);
    BEGIN
    out_file :=UTL_FILE.FOPEN('My_project\Outfile','abc.txt','w');
    l_line := 'HELLO TESTING';
    utl_file.put_line(out_file,l_line);
    UTL_FILE.FCLOSE(out_file);
    EXCEPTION
    WHEN no_data_found then
    UTL_FILE.FCLOSE(out_file);
    when others then
    raise_application_error(-20912, 'Others ' ||sqlerrm);
    END;
    I get
    ORA-29280: invalid directory path
    error.
    As there are many directories involved under My_project folder and there will be new directories created in the future as well, so I was wondering if there is a way to read files from any sub directory of My_project directory
    Please advise. Thanks for all your help.

    Hi Anto!
    Try it like this:
    out_file :=UTL_FILE.FOPEN('My_project','Outfile\abc.txt','w');I hope this helps!
    your sincerely
    Florian W.

  • HT1918 how to verify payment information if using paypal to purchase from itunes

    I recently changed the payment method for my itunes account from a credit card to paypal.  It states that I have to verify payment method before making purchases.  How do I do this

    Accepted forms of payment  >  http://support.apple.com/kb/HT5552
    Changing Payment Information  >  http://support.apple.com/kb/HT1918
    If necessary... Contact iTunes Customer Service and request assistance
    Use this Link  >  Apple  Support  iTunes Store  Contact

  • How to run powershell in adminsitrator mode using invoke-command

    Hi,
    I'm trying to run the below script from the remote machine I'm getting the output as below and the msnpatch.exe is not getting executed on the remote machine(testserver).
    When I run the same command on the testserver, a new powershell session is getting opened and able to run msnpatch.exe.
    So, how to invoke powershell in runas administrator mode and run msnpatch.exe on that administrator window is my question.
    Thanks for your time. Your reply is highly appreciated.
    Script:
    Invoke-Command -ComputerName testserver -ScriptBlock {
    $myWindowsID=[System.Security.Principal.WindowsIdentity]::GetCurrent()
    $myWindowsPrincipal=new-object System.Security.Principal.WindowsPrincipal($myWindowsID)
    $newProcess = new-object System.Diagnostics.ProcessStartInfo "PowerShell";
    $newProcess.Verb = "runas"
    $newProcess.Arguments="-noprofile -command msnpatch.exe"
    [System.Diagnostics.Process]::Start($newProcess)
    Output:
    PS C:\Users\v-sridal> Invoke-Command -ComputerName 1f4-00073 -ScriptBlock{
    >> $myWindowsID=[System.Security.Principal.WindowsIdentity]::GetCurrent()
    >> $myWindowsPrincipal=new-object System.Security.Principal.WindowsPrincipal($myWindowsID)
    >> $newProcess = new-object System.Diagnostics.ProcessStartInfo "PowerShell";
    >> $newProcess.Verb = "runas"
    >> $newProcess.CreateNoWindow = "true"
    >> $newProcess.Arguments="-noprofile -command msnpatch.exe"
    >> [System.Diagnostics.Process]::Start($newProcess)
    >> }
    >>
    Handles  NPM(K)    PM(K)      WS(K) VM(M)   CPU(s)     Id ProcessName                   
    PSComputerName
          4       4      244       1156     8     0.06   4968 powershell                    
    testserver

    There is no elevation when running remotely. UAC only affects local sessions. You cannot elevate a remote session.
    ¯\_(ツ)_/¯

  • Anybody knows how to verify USB link operation using Labview

    I am trying to verify the operation of a USB link on a system I am testing. Does Labview have USB drivers that provide data communication.

    hamid00 wrote:
    >
    > I am trying to verify the operation of a USB link on a system I am
    > testing. Does Labview have USB drivers that provide data
    > communication.
    No.
    Using LabVIEW, the best way might be to verify the operation of a device
    on the other end of the link ...
    Best, Mark

  • How to enable chunked streaming mode using OSB config file

    Hi All,
    Is there way through which we can enable and disable the chunked streaming mode option in Business service (of OSB) through OSB configuration file?? If yes, please let me know.
    Thanks,
    Aditya

    Hi Aditya,
    I don't think it can be done dynamically the way you described... But I believe you can create two business services, one with chunked=on and the other with chunked=off and route to one of them dynamically according to your configuration...
    Cheers,
    Vlad

  • How to verify, JavaFX 2.0 uses directx 9 on a XP box?

    I have a Windows XP installation on a Computer with a Intel 945 Chipset, which I want to run a JavaFX 2.0 App on. It has DirectX 9.29 installed, but it does not seem to utilize it, as the processor load is very high (70-100% for some hundret points refreshed 2-4 times a second. ok it's a weak device, but that's to high...)
    Is there a way to verify Prism utilizes the directx rendering?
    Thanks in advance...

    user4440549 wrote:
    I have a Windows XP installation on a Computer with a Intel 945 Chipset, which I want to run a JavaFX 2.0 App on. It has DirectX 9.29 installed, but it does not seem to utilize it, as the processor load is very high (70-100% for some hundret points refreshed 2-4 times a second. ok it's a weak device, but that's to high...)
    Is there a way to verify Prism utilizes the directx rendering?
    Thanks in advance...Hmm, what I know is that in Java2D the hardware pipeline is disabled by default for specific chipsets, notably Intel ones, because of unreliable drivers. That was quite a while ago, but it will probably still hold true for older chipsets. Perhaps JavaFX does something similar...

  • Understanding 7-Mode 'license show' command output

    What does the "-"/hyphen/dash mean in the Expiration field? How does one determine the current expiration of installed licenses based on this output? Package           Type    Description           Expiration
    NFS               license NFS License           -
    CIFS              license CIFS License          -
    FCP               license FCP License           -
    SnapRestore       license SnapRestore License   -
    SnapMirror        license SnapMirror License    -
    FlexClone         license FlexClone License     -
    SnapVault         license SnapVault License     - These services are currently active and in use yet, the Expiration field doesn't appear to reflect that we are licensed for them. I would expect it to at least say something other than the current output. This is confusing when trying to troubleshoot a potential licensing issue. Thank you in advance. I greatly appreciate it!

     Flippin Mango - Those are licenses with no expiration date, hence the blank field.See also the license command man page https://library.netapp.com/ecmdocs/ECMP1511537/html/man1/na_license.1.htmlThe only time I've seen expiration dates listed is when I've given a customer a temporary demo license for a feature.We also use temp license keys for lab excercises in the NetApp classes we teach. Noticed your login name.Had to share that my home in the US is in Flippin, Arkansas. : )
    I hope this response has been helpful to you.
    At your service,
    Eugene E. Kashpureff, Sr.
    Independent NetApp Consultant http://www.linkedin.com/in/eugenekashpureff
    Senior NetApp Instructor, IT Learning Solutions http://sg.itls.asia/netapp
    (P.S. I appreciate 'kudos' on any helpful posts.) 

  • How to encrypt file on linux using Gnupg command in Java Embedding in BPEL.

    Hi All,
    I am trying to invoke a command script using the java embedding in BPEL Process.I am using the below code to execute the particular command to encrypt the file :-
    try {    
            Runtime rt = Runtime.getRuntime();    
    Process pr = rt.exec(new String[] {"/bin/bash", "-c", "/u01/GnuPG/bin/gpg", "-e", "-r", "Developer","/u01/oracle/ConfigFiles/Adapter_controlDir/abc.csv"});    
             int exitVal = pr.waitFor();            
            String result = "SUCCESS: Process exit with " + exitVal;         
            addAuditTrailEntry("result = "+result);      
            setVariableData("outputVariable","payload","/client:processResponse/client:result",result);    
    } catch(Exception e) {    
            e.printStackTrace();      
      String result = "FAILURE: Exception with " + e.toString();    
            addAuditTrailEntry("result = "+result);      
            setVariableData("outputVariable","payload","/client:processResponse/client:result",result);    
    The above statement does nothing. I am not sure what command i need to use to access to the command line.
    When i try this particular statement from linux machine command prompt :- /u01/GnuPG/bin/gpg -e  -r  Developer /u01/oracle/ConfigFiles/Adapter_controlDir/abc.csv
    It works absolutely fine and it creates the encrypted files also.
    Please suggest , which command i need to use from the java embedding.
    Please suggest!!
    Regards,
    Shah

    I think, you can try, writing these commands into a separate shell script and call that shell script from bpel via Java embedding. However, you might not get a return response.. but you can still give a shot.
    Hope it helps.

Maybe you are looking for