How works DMZ with RV110W?

Greetings everyone,
It has been for several days that I tried to configure the DMZ with my new router but without success. I just need to get in my DMZ one machine hosting my shoutcast server. I have already opened the port used in my router:
Firewall > Single port forwarding
Application: Web Radio
External port: 7777
Internal port: 7777
Protocole: TCP
IP address: 10.10.10.101
Enable: OK
And for the DMZ:
Networking > LAN > DMZ Host
DMZ: Enable
VLAN: 1
Host IP Address: 10.10.10.101
Could anyone explain me what's wrong ? I'm starting to regret my purchase

Microsoft made many changes between the original preview and the current preview, so what worked in the earlier version may not work in the current one, and vice versa. Again, Apple's software is not yet supported in Windows 8 and almost certainly will not be until Win 8 is officially released, if then. You may be able to get the standalone installer to work, but if you can't, you'll just have to wait for a supported release, or take the issue up on a forum for the Windows 8 Preview and see if someone there can help you.
Regards.

Similar Messages

  • How works itunes with Win8

    I know, it's bettere OS system but I have to use Windows at work. How can use win8 with Itunes?
    I have to make a back ap for my iphone4 but it's impossibile with my pc win8

    Microsoft made many changes between the original preview and the current preview, so what worked in the earlier version may not work in the current one, and vice versa. Again, Apple's software is not yet supported in Windows 8 and almost certainly will not be until Win 8 is officially released, if then. You may be able to get the standalone installer to work, but if you can't, you'll just have to wait for a supported release, or take the issue up on a forum for the Windows 8 Preview and see if someone there can help you.
    Regards.

  • FCS and image sequences (TGA...) : how works the proxy creation?

    Hello,
    I would like to know how work FCS with image sequences (TGA, TIFF sequences...) for proxy creation.
    For example, the image sequences are created by 3D workstation at the speed of one frame per second.
    Does FCS create a proxy each time the folder is checked? The old proxy is delated?
    Thank you for your answer

    Jim is right. You can't replace a clip with an image sequence.
    If you are rendering your comps from one system, follow Jim's sage advice.
    But, in the cases when I do a multi-system network 3d render, there is
    no way for all systems to write to the same Uncompressed AVI file...
    so rendering to an image sequence is the only option.
    You say:
    ...for speed reasons -  converting them to lower res quicktime files
    and using those to edit in Premiere Pro.
    You might consider converting your sequences to both a low-res proxy for editing,
    and also convert to full-res lossless codec AVI files at the same time for swapping out later.

  • How Can i Use two Different Public IP Addresses no my DMZ with ASA Firewall.

    How To Using Two Different Public IP Address on My DMZ with ASA 5520
    Postado por jorge decimo decimo em 28/Jan/2013 5:51:28
    Hi everyone out there.
    can any one please help me regarding this situation that im looking for a solution
    My old range of public ip address are finished, i mean (the 41.x.x.0 range)
    So now i still need to have in my DMZ another two servers that will bring some new services.
    Remember that those two server, will need to be accessable both from inside and from outside users (Internet users) as well.
    So as i said, my old range of public ip address is finished and we asked the ISP to gives some additional public
    ip address to address the need of the two new servers on DMZ. and the ISP gave us the range of 197.216.1.24/29
    So my quation is, on reall time world (on the equipment) how can i Use two different public ip address on the same DMZ
    on Cisco ASA 5520 v8??
    How my configuration should look like?
    I was told about implementing static nat with Sub Interfaces on both Router and ASA interface
    Can someone please do give me a help with a practical config sample please. i can as well be reached at [email protected]
    attached is my network diagram for a better understanding
    I thank every body in advance
    Jorge

    Hi,
    So looking at your picture you have the original public IP address range configured on the OUTSIDE and its used for NAT for different servers behind the ASA firewall.
    Now you have gotten a new public IP address range from the ISP and want to get it into use.
    How do you want to use this IP address range? You want to configure the public IP addresses directly on the servers or NAT them at the ASA and have private IP addresses on the actual servers (like it seems to be for the current server)?
    To get the routing working naturally the only thing needed between your Router and Firewall would be to have a static route for the new public network range pointing towards your ASA OUTSIDE IP address. The routing between your Router and the ISP core could either be handled with Static Routing or Dynamic Routing.
    So you dont really need to change the interface configuration between the Router and ASA at all. You just need a Static route pointing the new public IP address towards the ASA outside IP address.
    Now when the routing is handled between the ISP - ISP/Your Router - Your Firewall, you can then consider how to use those IP addresses.
    Do you want to use the public IP addresses DIRECTLY on the HOSTS behind the firewall?This would require you to either configure a new physical interface with the new public IP address range OR create a new subinterface with the new public IP addresses range AND then configure the LAN devices correspondingly to the chosen method on the firewall
    Do you want to use the public IP addresses DIRECLTY on the ASA OUTSIDE as NAT IP addresses?This would require for you to only start configuring Static NAT for the new servers between the inside/dmz and outside interface of the ASA. The format would be no different from the previous NAT configuration other than for the different IP addresses ofcourse
    Of the above ways
    The first way is good because the actual hosts will have the public IP addresses. Therefore you wont run into problems with DNS when the LAN users are trying to access the server.
    The second way is the one requiring the least amount of configurations/changes on the ASA. In this case though you might run into problem with DNS (to which I refer above) as the server actually has a private IP address but the public DNS might reply to the LAN hosts with a public IP address and therefore connections from LAN could fail. This is because LAN users cant connect to the servers OUTSIDE NAT IP address (unless you NAT the server to public IP address towards LAN also)
    Hopefully the above was helpfull. Naturally ask more specific questions and I'll answer them. Hopefully I didnt miss something. But please ask more
    I'm currently at Cisco Live! 2013 London so in the "worst case" I might be able to answer on the weekend at earliest.
    - Jouni

  • Photoshop CC2014 running under window 8.1.  How do I access mini bridge.  It does not show under FILE or WINDOW-EXTENSIONS.  Works ok with CS6

    Photoshop CC2014 running under window 8.1.  How do I access mini bridge.  It does not show under FILE or WINDOW-EXTENSIONS.  Works ok with CS6

    Photoshop: Spring Cleaning | PHOTOSHOP.COM BLOG

  • I have a mid-2010 iMac and just purchased a 2TB TC, can't join existing wireless network with AC standard so attached to iMac via ethernet with TC wifi turned off.  How do i access TC now? not showing up in disk utility or on desktop. working fine with TM

    I have a mid-2010 iMac and just purchased a 2TB TC, I just found out that it can't join existing wireless network with new AC standard so attached to iMac via ethernet with TC's wifi turned off.  How do i access TC now? not showing up in disk utility or on desktop. It is working fine with TM.  My cheeper seagate drives etc kept crashing, so i didnt trust cheeper back up options anymore.  Connected those drives to TM via firewire and could see the drives and access them.
    Also, I didn't want to bridge TC with my new fios router that I paid 100 dollars for, to get N speed and also paying 10 dollars more a month for fast speed.  I heard that bridging slows down everything and then there can be port issues with mail etc.  I connect to the internet via airport only and it is pretty fast. Getting over 50mbs downloads and over 30mbs uploads.  Plus everything in my home it connected to my fios router, airport express for music streaming, two apple tvs, vuezone camer system.  I really didn't want to monkey around too much with my system.  But are there other options to connect the new TC.  Can't find info anywhere for this and called apple who gave me the info above.  after hanging up, i see that i cant access my TC and I am wondering if i would have to reset it to turn wifi on again to make changes to the drive, turn off blinking light  or repair it in disk utility if it should become corrupted.
    For other with similar issues i did solve some other problems: when i connected it to my ethernet port on my iMac wifi stopped working.  Found that I had to turn off the ethernet in the system>network screen, but then TM didn't see the TC so i restarted after changes and then it saw it.
    Now a rant.  I can't believe in this wireless age that Apple would make a product that cant join a wireless net work.  The apple rep said i could return it and look for the previous TC that would join an existing wireless network.  Are we going backwards?
    Thanks!
    lennydas

    Ok... it is getting a bit clearer but there are still some questions.
    I connect to the internet via airport only and it is pretty fast.
    I was assuming airport in this statement in your first post meant the TC or the Express.. but I now realise we are still in the mass confusion stage where apple calls everything wireless an airport. So what you mean is the airport internal card of the computer??
    Also, I didn't want to bridge TC with my new fios router that I paid 100 dollars for, to get N speed and also paying 10 dollars more a month for fast speed.  I heard that bridging slows down everything and then there can be port issues with mail etc.
    I think this is mistaken.
    Putting the TC in bridge mode plugged into your FIOS will not slow the network.. nor will it cause mail or port issues.. in bridge the TC is just a fancy WAP and switch plus the network hard drive.
    If the computer is close it will be faster than the FIOS.
    You can run both wireless networks with different names.. so it is clear which is which. But you can also setup roaming so the computers themselves pick which is the best wireless.
    I tried extending the wireless net work and tried joining wireless network, but the TC kept crashing and I had to keep resetting the TC.  the Apple support person said these, extend wireless network and joint wireless network, are no longer a connection option with the new TC because of the new AC protocol.
    Thanks again!
    You cannot extend to a non-apple wireless router.
    You cannot use join a wireless network because when you do the ethernet ports will be cut off.
    But that has not changed.. I don't think Apple support is correct.. there has been no change with the AC model.. it is simply a fact that apple routers do not work in join wireless mode other than as a dumb client. The same applies to AC as to the earlier version.. but I have asked another person to check this.
    Join in the express is the only apple router that still allows an ethernet connection.
    For now you best use of the TC is bridged to the FIOS. Wireless you can sort out between several options.

  • How do I connect to Net Flix? I put in my user name and password which work fine with my iMac but not on my Apple TV?

    How do I connect to Net Flix? I put in my user name and password which work fine with my iMac but not on my Apple TV?

    Can you give me a screenshot of the User Accounts window in Control Panel?
    Please create a screenshot by following the guide mentioned at [[How do I create a screenshot of my problem?]].
    Once you've done this, attach the saved screenshot file to your forum post by clicking the '''Browse...''' button below the ''Post your reply'' box. You really help us to visualize the problem.

  • With 10.2 I can only use system speaker output for audio, NOT my RME FF400 I used previously. The FF400 works fine with other apps. How can I set this device in FCP 10.2? (it is set in both system preferences and midi)

    With 10.2 I can only use a system (e.g. speaker) output for audio, NOT my RME FF400 I used without any problems previously. The FF400 works fine with other apps (some like TwistedWave) setup in the program, and others (like Spotify) using system preferences & audio midi setup. How can I set the FF400 to be the sound output device in FCP 10.2? N.B. The FF400 is set as sound output device in both system preferences and audio midi setup.

    From the fcp.co forum. See if this does anything for you.
    simon_hutchings
    OFFLINE
    Junior Boarder
    Posts: 24
    Thank you received: 5
    Karma: 1
    I have the solution! Well it at least worked for me. This is the response I got from Apple, Can you please try the following steps towards fixing your audio issue, and report back with your results?
    1. Open the application Audio Midi Setup (located in Applications : Utilities)
    2. Select the Output Tab for the current output device
    3. Select the Configure Speakers option
    4. Select the Multichannel tab
    5. Change the setting to Stereo Now mine was set to stereo but the left channel wasn't showing left. re-clicking on stereo reloaded the settings and after clicking apply it worked. 

  • How do I get a virtual lab to play,quicktime does not work with this CD,I have quicktime on other computers works fine with this CD. Technician said Cd could

    How  do  I  get  a  virtual lab to  work  on  this  computer.  The  technician  said  the  CD  is  not  compatible. Maybe  corrupt. He  seemed  he  did  not  know
    what  he  was  talking  about. I  asked  him  was  it  any  software  I  could  download  he  said  no.  This  CD  works  fine  on  my  other  computer, no  it  is  not  an  apple  computer. And  I  use  quicktime  on  both  computers. But  on  this  apple  computer  quicktime  does  not  play  this  CD, which  this  type
    of  CD  works  better  with  quicktime. Any  suggestions  on  how  to  solve  this  problem.  This  is  a   new  computer,  I  would  hate  to  think  their  is  nothing  that  can  be  done.

    I  need  step  by step  instructions  on  how  to  get  my  virtual  lab  cd  to  work. The  technician  said  cd  not  compatible  or  is  corrupt.  I  do  not  believe  their  is  nothing  that  can  be  done.  When  I  put  the  cd  in  the  side  slot  nothing  comes  up  on  the  screen.  I  have  tried  several   ways, the  technician  did  not  seem  very  knowledgeable  on  what  to  do. Also  this  cd  plays  fine  on  my  other  computer  which  is  not  an  apple  computer. Is  there  anything  I  can  do  to  correct  this?

  • How can I create a client console and work together with the Cache Server?

    How can I edit the following Cache-Server.cmd file to create a client console and work together with the Cache Server?
    The following is the cache server file: contacts-cache-server.cmd
    @echo off
    setlocal
    if (%COHERENCE_HOME%)==() (
    set COHERENCE_HOME=c:\coherence
    set CONFIG=C:\home\oracle\coherence\Contacts
    set COH_OPTS=%COH_OPTS% -server -cp %COHERENCE_HOME%\lib\coherence.jar;C:\home\oracle\
    coherence\Contacts;C:\home\oracle\coherence\Contacts\classes;
    set COH_OPTS=%COH_OPTS% -Dtangosol.coherence.cacheconfig=%CONFIG%\contacts-cache-config.xml
    java %COH_OPTS% -Xms1g -Xmx1g -Xloggc: com.tangosol.net.DefaultCacheServer %2 %3 %4 %5 %6 %7
    :exitEdited by: junez on 23-Oct-2009 09:20

    Hi
    To run the console, change DefaultCacheServer to CacheFactory
    Paul

  • How to deactivate *Schedule Background Job for Work Items with Errors* SWU3

    Hello Guys,
    Can any one tell me how do I DEACTIVATE Schedule Background Job for Work Items with Errors in sap workflow SWU3.
    Currently it is green which I don't want. I want to stop this service.
    Regards
    NK

    Hello,
    You could also just stop the job in tx SM37.
    But why would you want to do this? As a test?
    regards
    Rick Bakker
    hanabi technology

  • When I navigate web with Firefox my Thinkpad trackpoint center button is not working. With other web browsers it works well. Where is the problem in firefox, how to enable TrackPoint center button?

    When I navigate web with Firefox my Thinkpad trackpoint center button is not working. With other web browsers it works well. Where is the problem in firefox, how to enable TrackPoint center button?

    I have exactly the same settings in Options (in both computers)
    for history, these 2 add-ons and all other stuff in Options. The only difference is that on 1 pc sessions can be saved and closed tabs can be reopened, on other main pc they stopped to work. + no any other add-on that does similar things works on this pc.
    It is also interesting that I can reopen closed visited sites from History Panel, but not by pressing the Button. For now I only manually bookmark links to a temporary folder.
    Recently (some 2 month ago) I pressed x and Firefox closed all tabs without saving them without displaying save & quit pop up.
    so I changed 4 settings in about.config
    browser.tabs.warn on close true
    browser.warn on quit true
    browser.warn on restart true
    browser.show.quit warning true
    but the problem with sessions appeared only 1 week ago.
    So I guess the problem is not with the History settings or other settings. Seems that something responsible for button or for storing info about tabs/sessions got corrupted. :(

  • Working alternating with iPhoto and FCE tgrying to import pictures from iPhoto into FCE suddenly all my 22300 pictures disappeared leaving empty frames. Does somebody know where the pictures could have gone and how can I get them back into iPhoto? Lothar

    Working alternating with iPhoto and FCE tgrying to import pictures from iPhoto into FCE suddenly all my 22300 pictures disappeared leaving empty frames. Does somebody know where the pictures could have gone and how can I get them back into iPhoto? Lothar

    The ! turns up when iPhoto loses the connection between the thumbnail in the iPhoto Window and the file it represents.
    Option 1
    Back Up and try rebuild the library: hold down the command and option (or alt) keys while launching iPhoto. Use the resulting dialogue to rebuild. Choose to Rebuild iPhoto Library Database from automatic backup.
    If that fails:
    Option 2
    Download iPhoto Library Manager and use its rebuild function. This will create a new library based on data in the albumdata.xml file. Not everything will be brought over - no slideshows, books or calendars, for instance - but it should get all your albums and keywords back.
    Because this process creates an entirely new library and leaves your old one untouched, it is non-destructive, and if you're not happy with the results you can simply return to your old one. .
    Regards
    TD

  • How can I work lsmw with table control using mm01 appl?

    Hi
    How can I work lsmw with table control using mm01 appl?
    Is it difefrent the way we handle table control in BDC?
    Thank You

    Hi
    How can I work lsmw with table control using mm01 appl?
    Is it difefrent the way we handle table control in BDC?
    Thank You

  • Someone who can say how to get Adpbe flash player version 11.2.202.197 to work together with Lion on mac mini. Support from Apple can obviously not help the problem and do not care if it works

    Someone who can say how to get Adpbe flash player version 11.2.202.197 to work together with Lion on mac mini. Support from Apple can obviously not help the problem and do not care if it works

    Adobe flash player version 11.2.202.197 is for Windows Vista / Windows 7 / Vista 64 / Windows 7 64
    Adobe Flash Player version 11.1.102.55 is the current version for Snow Leopard and Lion.
    Adobe - Install Adobe Flash Player

Maybe you are looking for