HP 12C Calculator
My HP 12C calculator is not calculating correctly. For example, when I type in a simple equasion such as 5*6 I get 36, or 2*9 gives me 81. I am not exactly sure if I hit a button by mistake which is causing the calculator to do this, or if something is not working correctly. Any insights are appreciated it!
Hi,
The 12C uses RPN entry for calculations, so 5*6 is done as:
5 Enter 6 *
and 2*9 is done as:
2 Enter 9 *
This might seem cumbersome at first, but works well for longer expressions.
I suggest you read the following:
http://www.hpmuseum.org/rpn.htm
and especially the section "learning RPN":
http://www.hpmuseum.org/rpn.htm#learn
Hope this helps.
Note: I do not work for HP, I just like playing with calculators :-)
Similar Messages
-
Hi,
How can I fix the 12C to make it work properly?
I've already bought 2 and both of them have the same problem. I get the error message "Prob Error" every time I want to use any of the functions on the left side (financial functions, exp, ln...).
I'm very disappointed, I reset them a few times using the different methods (paperclip, coins, removing the bateries) but nothing works.
May you please help me with this?
Thanks,
SaraHi,
I suspect the message you are getting is "Pr Error".
Put in new batteries of a good brand from a reputable source.
The problem is that the low battery indicator does not work properly. When the batteries are low and a function key is pressed the calculator essentially resets and a "Pr Error" message results. Unfortunately it means that the program memory is deleted too.
By the way, if checking the batteries you should use a battery checker that puts a load on it and not just with a volt meter - otherwise you are just seeing a good no-load voltage (just like the low battery detection circuit of the calculator).
Best regards.
Note: I do not work for HP, I just like playing with calculators :-) -
CALC 12C - Where did it go?!? What now?
I had downloaded a wonderful app "CALC 12C" which was a terrific emulation of the HP 12C calculator, and free. It was from Crimson Research. I still have it on my iPhone, no problem. Yet.
What happened? Anyone know?
Perhaps more to the point, when Apple pulls an application, what happens -- will it disappear on my next sync, or next app store update? Will I be able to go to firmware 2.3 and have it remain? When I got a new phone once, it was suggested I re-downlaod them all from scratch. I did, no problem and no new charges -- obviously couldn't now, so I'd be restoring with iTunes, does it check that it is still an approved app?I will.
I've been doing a lot of reading in the various websites where work on HP calculator simulation is done, and there appear to be licensing or copyright issues with some later microcode, e.g. I see where the nonpareil distribution was being discussed as split between free and not over this. So it may well be that some kind of copyright issue arose. There's a fair amount of history for other efforts, none for this free one, so I did not learn much.
As to comments about others -- there are, some quite expensive. Plus I love to encourage the GNU and similar efforts when they appear, I'd rather donate to a freeware GNU effort than pay the same for a commercial product. -
Calculation Field to be mapped to different data object's column name in Oracle BAM 12c
Hi,
I am having a challenge to enable drill down to 2nd level report by passing calculation field as parameter.
As an alternative, I am thinking to point calculation field to another data object’s column name and generate report so that I would be able to pass that as parameter to drilling report view.
Is there any way to map calculation field to different Data object’s column name? Thanks in advance.
Regards
Amik Basu1. Yes, you can.
SQL> create table ÜÝÞ( ßàá number(10));
Table created.
SQL> insert into ÜÝÞ values (10);
1 row created.1.1 and 1.2 and 2. You can choose UTF as your default character set. It allows the user of non-English characters in VARCHAR columns in your whole database. It is not per tablespace.
SQL> create table ÜÝÞ( ßàá varchar2(100));
Table created.
SQL> insert into ÜÝÞ values ('âãäçìé');
1 row created. -
Silent installation of Cloud agent 12c failed on a windows 2003 host
Hello All,
I've done multiple installations by silently installing the cloud agent 12c using a response file. However, the configuration portion failed on this one windows 2003 host.
Has anyone seen this? I've searched on metalink and see other problems like TZ, service already exists, incorrect PERL settings etc..but found nothing that helps so far.
In log file:
The action configuration is performing
The plug-in Agent Configuration Assistant is running
AgentConfiguration:agent configuration has been started
Validating OMS_HOST and EM_UPLOAD_PORT
Performing free port detection..
AgentConfiguration: Executing emctl deploy agent command...
AgentConfiguration:agent configuration finished with status = false
The plug-in Agent Configuration Assistant has failed its perform method
The action configuration has failed its perform method
In Agent Deploy log file:
value passed to dir splitC:/oracle/em/agent_inst
INFO: length of temp is2
INFO: Return value:C:
\/oracle/em/agent_inst
INFO: ** Agent Port Check completed successfully.**
INFO: ERROR: The
Management Agent configuration failed. The plug-in configuration for the oracle.sysman.oh
monitoring plug-in may have failed, or this plug-in may not be present in the Management Agent
software. Ensure that the Management Agent software has the oracle.sysman.oh monitoring plug-in,
if not then retry the operation. If the agent software has the oracle.sysman.oh monitoring plug-
in, view the plug-in deployment log C:\oracle\em\agent_inst\install\logs to check if the plug-in
configuration for the oracle.sysman.oh monitoring plug-in failed.
INFO:
INFO: perform - mode
finished for action: configure
INFO:
INFO: You can see the log file: C:\oracle\em\core
\12.1.0.3.0\cfgtoollogs\oui\configActions2013-12-23_11-07-08-AM.log
INFO:
INFO: C:\oracle\em>exit
/b 3
INFO: Plugin homes:
INFO: Plugin homes:
INFO: C:\oracle\em\core\12.1.0.3.0\oui\bin
\runConfig.bat ORACLE_HOME=C:\oracle\em\core\12.1.0.3.0 RESPONSE_FILE=C:\oracle\em\core
\12.1.0.3.0\agent.rsp ACTION=configure MODE=perform COMPONENT_XML=
{oracle.sysman.top.agent.11_1_0_1_0.xml} RERUN=true completed with status=3
SEVERE: ERROR: Agent
Configuration Failed
SEVERE: ERROR: Agent Deployment FailedThanks for the reply Rahul.
I've used that same response file for deployments on other servers without any problem.
See response file below: (note i've changed the server name)
## copyright (c) 1999, 2012 Oracle. All rights reserved. ##
## Specify values for the variables listed below to customize ##
## your installation. ##
## Each variable is associated with a comment. The comment ##
## identifies the variable type. ##
## Please specify the values in the following format: ##
## Type Example ##
## String "Sample Value" ##
## Boolean True or False ##
## Number 1000 ##
## StringList {"String value 1","String Value 2"} ##
## The values that are given as <Value Required> need to be ##
## specified for a silent installation to be successful. ##
## This response file is generated by Oracle Software ##
## Packager. ##
RESPONSEFILE_VERSION=2.2.1.0.0
#OMS_HOST:<String> OMS host info required to connect to OMS
#EM_UPLOAD_PORT:<String> OMS port info required to connect to OMS
#AGENT_REGISTRATION_PASSWORD:<String> Agent Registration Password needed to
# establish a secure connection to the OMS.
#AGENT_INSTANCE_HOME:<String> Agent instance home is the location of agent state directory.
#AGENT_PORT:<String> Agent port on which the agent process should be started.
#b_startAgent:<boolean> Agent will not be started after configuration if the value specified is false.
#ORACLE_HOSTNAME:<String> Fully qualified domain name of host where is the agent is deployed.
#s_agentHomeName:<String>Customized Oracle home name for the agent home. Example: s_agentHomeName="agent12gR1"
OMS_HOST="omshost.company.com"
EM_UPLOAD_PORT="1159"
AGENT_REGISTRATION_PASSWORD="complicatedpassword"
AGENT_INSTANCE_HOME="e:/oracle/em/agent_inst"
AGENT_PORT="3872"
b_startAgent=true
ORACLE_HOSTNAME="targetserver.company.com"
#s_agentHomeName=<Value Unspecified>
#s_agentSrvcName:<String> Sets the agent Service Name and this variable can be
# used to overrite the agent service name calculated by the install. This is
# required for only Windows.
# Example:
# s_agentSrvcName = "GridAgent" ; User specified value
#s_agentSrvcName=""
#Please Don't change the values of these variables
#EM_INSTALL_TYPE:<STRING> install type
EM_INSTALL_TYPE="AGENT" -
OMS 12c Upgrade Stuck at this error Error in invoking target 'client_shared
Hi All
We are Upgrading OMS from 11.1 to 12c
stuck at this error after invoking runInstaller
Following 1 system upgrade. (graphical mode).
INFO: Start output from spawned process:
INFO: ----------------------------------
INFO:
INFO: /opt/app/wls/oms12c/oms/bin/genclntsh
INFO: make: execvp: /opt/app/wls/oms12c/oms/bin/genclntsh: Permission denied
INFO: make: *** [client_sharedlib] Error 127
INFO: End output from spawned process.
INFO: ----------------------------------
INFO: Exception thrown from action: make
Exception Name: MakefileException
Exception String: Error in invoking target 'client_sharedlib' of makefile '/opt/app/wls/oms12c/oms/rdbms/lib/ins_rdbms.mk'. See '/opt/app/oraInventory/logs/installActions2012-08-02_06-38-02-PM.log' for details.
Exception Severity: 1
INFO: POPUP WARNING:Error in invoking target 'client_sharedlib' of makefile '/opt/app/wls/oms12c/oms/rdbms/lib/ins_rdbms.mk'. See '/opt/app/oraInventory/logs/installActions2012-08-02_06-38-02-PM.log' for details.
Click "Retry" to try again.
Click "Ignore" to ignore this error and go on.
Click "Cancel" to stop this installation.
Please Advise
Edited by: TechAdmin on Aug 2, 2012 4:09 PM
Edited by: TechAdmin on Aug 2, 2012 4:11 PMI installed all the packages and it allowed me to proceed furthur
but now it throws another error saying that
The log says "ORA-12003: materialized view "SYSMAN"."MGMT_ECM_MD_ALL_TBL_COLUMNS" does not exist" during the OMS Upgrade using graphical mode.
We are not sure if that Materialized view ever exists on it or not.
Please advise
Below is the detailed log :
INFO: oracle.sysman.top.oms:Failure...
INFO: oracle.sysman.top.oms:exiting the thread...
INFO: oracle.sysman.top.oms:[Initializing the EM RCU Runner, Failed Parameter Validation]
INFO: oracle.sysman.top.oms: action logger path calculated finally: /opt/app/wls/OMS12c/oms/sysman/log/schemamanager/m_073012_1147_AM/m_073012_1147_AM.TRANSX/
INFO: oracle.sysman.top.oms:The transx command execution is completed with the status 255
INFO: oracle.sysman.top.oms:The transx action failed, Run the RepManager with -action transx
INFO: oracle.sysman.top.oms:process_id:dr40kpyuxcpe
INFO: oracle.sysman.top.oms:Failure...
INFO: oracle.sysman.top.oms:1 error(s) happened in performing the action:
INFO: oracle.sysman.top.oms:1):
ORA-12003: materialized view "SYSMAN"."MGMT_ECM_MD_ALL_TBL_COLUMNS" does not exist
File:/opt/app/wls/OMS12c/oms/sysman/admin/emdrep/sql/core/11.2.0.1/ecm/ecm_tables_alter.sql
Statement:DROP MATERIALIZED VIEW MGMT_ECM_MD_ALL_TBL_COLUMNS
INFO: oracle.sysman.top.oms:The plug-in Repository Upgrade has failed its perform method
The other logs at <OMS_HOME>sysman/log/schemamanager/* says that the index is missing we checked our backups and all other possible ways to find if that index ever existed but we dont see anything as such.
2012-08-06 12:07:54,476 [t970bytvwebs] INFO emschema.t970bytvwebs - index on mgmt_messages found: true on try: 196
2012-08-06 12:08:00,479 [t970bytvwebs] INFO emschema.t970bytvwebs - index on mgmt_messages found: true on try: 197
2012-08-06 12:08:06,570 [t970bytvwebs] INFO emschema.t970bytvwebs - repos connection is not null, using old one
2012-08-06 12:08:06,571 [t970bytvwebs] INFO emschema.t970bytvwebs - executing: SELECT count(*) FROM all_objects WHERE object_name='MGMT_MESSAGES_IDX_01' AND owner='SYSMAN'
2012-08-06 12:08:06,572 [t970bytvwebs] INFO emschema.t970bytvwebs - index on mgmt_messages found: true on try: 198
2012-08-06 12:08:12,574 [t970bytvwebs] INFO emschema.t970bytvwebs - index on mgmt_messages found: true on try: 199
2012-08-06 12:08:18,576 [t970bytvwebs] INFO emschema.t970bytvwebs - not found index on mgmt_messages
2012-08-06 12:08:18,576 [t970bytvwebs] INFO emschema.t970bytvwebs - error: not found index on mgmt_messages for transx repos user exists: true mgmt_messages exists: true; index on mgmt_messages exist: false; found connection for repos user: true
2012-08-06 12:08:18,576 [t970bytvwebs] ERROR emschema.t970bytvwebs - Failed Parameter Validation
2012-08-06 12:08:18,576 [t970bytvwebs] ERROR emschema.t970bytvwebs - NULL Exception was thrown!
2012-08-06 12:08:18,576 [t970bytvwebs] ERROR emschema.t970bytvwebs - Failed Parameter Validation
we never had that index in our database.so that we could go back and check if that exits
Please suggest a solution for this.
Thanks
Unfortunately we dont have any other database to compare it to see wether it exits
Edited by: TechAdmin on Aug 6, 2012 11:34 AM -
Hi ,
I'm facing the problem with 'Repository Configuration' when installing EM 12c on WIndows 7.
The installation gets stuck at 47% . My database doesn't have any pluggable database and SYSMAN has never been created before. Can you please help with this problem ?
NFO: oracle.sysman.top.oms:The command run for transx is C:\Middle\oms\sysman\admin\emdrep\bin\RepManager.bat -connect (DESCRIPTION=(ADDRESS_LIST=(ADDRESS=(PROTOCOL=TCP)(HOST=orcs9003.shire.local)(PORT=1521)))(CONNECT_DATA=(SID=TEST))) -action transx -repos_user SYSMAN -dbUser SYS -mwHome C:\Middle -mwOraHome C:\Middle\oms
INFO: oracle.sysman.top.oms:processing arguments
INFO: oracle.sysman.top.oms:compiling arguments for validation
INFO: oracle.sysman.top.oms:'stty' is not recognized as an internal or external command,
INFO: oracle.sysman.top.oms:operable program or batch file.
INFO: oracle.sysman.top.oms:'stty' is not recognized as an internal or external command,
INFO: oracle.sysman.top.oms:operable program or batch file.
INFO: oracle.sysman.top.oms: Enter SYSMAN repository password :
INFO: oracle.sysman.top.oms:'stty' is not recognized as an internal or external command,
INFO: oracle.sysman.top.oms:operable program or batch file.
INFO: oracle.sysman.top.oms:'stty' is not recognized as an internal or external command,
INFO: oracle.sysman.top.oms:operable program or batch file.
INFO: oracle.sysman.top.oms:Verify :
INFO: oracle.sysman.top.oms:Enter password for: SYSMAN
INFO: oracle.sysman.top.oms: done checking required user credentials...
INFO: oracle.sysman.top.oms:done creating arguments...
INFO: oracle.sysman.top.oms:creating logger..
INFO: oracle.sysman.top.oms: Connection exception in action logger path calculated: C:\Middle\oms\sysman\log\schemamanager\
INFO: oracle.sysman.top.oms: action logger path calculated: C:\Middle\oms\sysman\log\schemamanager\
INFO: oracle.sysman.top.oms: action logger path calculated finally: C:\Middle\oms\sysman\log\schemamanager\
INFO: oracle.sysman.top.oms: no action logger file name from previous session
INFO: oracle.sysman.top.oms: action logger filename after search: emschema.log
INFO: oracle.sysman.top.oms: action logger filename finally: emschema.log
INFO: oracle.sysman.top.oms:Logger FileName:C:\Middle\oms\sysman\log\schemamanager\emschema.log
INFO: oracle.sysman.top.oms:already exists: C:\Middle\oms\sysman\log\schemamanager\emschema.log
INFO: oracle.sysman.top.oms:oracleHome: C:\Middle\oms
INFO: oracle.sysman.top.oms:connect_string: (DESCRIPTION=(ADDRESS_LIST=(ADDRESS=(PROTOCOL=TCP)(HOST=orcs9003.shire.local)(PORT=1521)))(CONNECT_DATA=(SID=TEST)))
INFO: oracle.sysman.top.oms:done connection validation without error
INFO: oracle.sysman.top.oms:action to perform is: transx
INFO: oracle.sysman.top.oms:action to be performed:TRANSX
INFO: oracle.sysman.top.oms:action is transx - non RCU based action
INFO: oracle.sysman.top.oms: action logger path calculated finally: C:\Middle\oms\sysman\log\schemamanager\m_2013-07-23_1613\m_2013-07-23_1613.TRANSX\
INFO: oracle.sysman.top.oms: action logger path calculated finally: C:\Middle\oms\sysman\log\schemamanager\m_2013-07-23_1613\m_2013-07-23_1613.TRANSX\
INFO: oracle.sysman.top.oms: action logger filename finally: emschema.log.TRANSX
INFO: oracle.sysman.top.oms:Failure...
INFO: oracle.sysman.top.oms:exiting the thread...
INFO: oracle.sysman.top.oms:[Initializing the EM RCU Runner, Failed Parameter Validation]
INFO: oracle.sysman.top.oms: action logger path calculated finally: C:\Middle\oms\sysman\log\schemamanager\m_2013-07-23_1613\m_2013-07-23_1613.TRANSX\
INFO: oracle.sysman.top.oms:The transx command execution is completed with the status 0
INFO: oracle.sysman.top.oms:process_id:1hqlayg7hyxmo
INFO: oracle.sysman.top.oms:Failure...
INFO: oracle.sysman.top.oms:1 error(s) happened in performing the action:
INFO: oracle.sysman.top.oms:1):
ORA-65096: ogiltigt namn för gemensam användare eller roll
File:C:\Middle\oms\sysman\admin\emdrep\sql\core\latest\admin\admin_create_repos_user.sql
Statement:CREATE USER SYSMAN IDENTIFIED BY ****** DEFAULT TABLESPACE MGMT_TABLESPACE QUOTA UNLIMITED ON MGMT_TABLESPACE TEMPORARY TABLESPACE TEMP
INFO: oracle.sysman.top.oms:The plug-in Repository Configuration has failed its perform method
Best Regards
TienHi,
Because you mentioned that you do not have any pluggable database, and because pluggable databases are new in Oracle Database 12c, I have to ask: Are you trying to install EM12c using Oracle Database 12c as the repository database? If so, this is not a supported configuration and I would strongly suggest that you select one of the certified versions of the database (like 11.2.0.3) to use for your repository database.
-Brian -
Hi All,
We are trying to install EM 12c on Linux 4 [32 bit] with 11.1.0.7 database, but we are facing problem while the installation configures the repository.[Repository configuration].
We found the fallowing error message from the log file:
INFO: oracle.sysman.top.oms:Failure...
INFO: oracle.sysman.top.oms:exiting the thread...
INFO: oracle.sysman.top.oms:[Initializing the EM RCU Runner, Failed Parameter Validation]
INFO: oracle.sysman.top.oms: action logger path calculated finally: /data1/OEM12/MiddleWare/oms/sysman/log/schemamanager/m_031413_0816_PM/m_031413_0816_PM.TRANSX/
INFO: oracle.sysman.top.oms:The transx command execution is completed with the status 255
INFO: oracle.sysman.top.oms:transx_retCode:255
INFO: oracle.sysman.top.oms:*The transx action failed, Run the RepManager with -action transx*
INFO: oracle.sysman.top.oms:process_id:qzy3sxnutyom
INFO: oracle.sysman.top.oms:Failure...
INFO: oracle.sysman.top.oms:*The plug-in Repository Configuration has failed its perform method*
INFO: Cfm.save() was called
INFO: Cfm.save(): 6 aggregate instances saved
INFO: done waiting for Action from 20:15:26.190
Please help me to resolve the issue. Note: All the instllation prerequisites were success except swap.
Thanks
skjb@skjb, we need to look into more schemamanager logs and cfgtools logs. Can you open an SR and share the number:
After looking at the logs i will tell you how to procedd and what caused the issue
Logs to upload :
- $ORACLE_HOME/sysman/log/schemamanager zipped (/data1/OEM12/MiddleWare/oms/sysman/log/schemamanager/*.*)
- $ORACLE_HOME/cfgtoollogs/ zipped
- central inventory logs oraInventory/logs/*.* -
Is there a way to find stated interest rate on HP 12C?
Help, I am trying to get compute the "stated interest rate" on the HP 12c given the PV is 1000 and FV is 1061.68 and n is 12 ( 1year compounded monthly). I keep getting Error 5 when I enter these inputs and then press i. I even played around with the sign conventions. Nothing works. The answer is 6, but I am trying to obtain the result on the calculator.
Hi,
It is about the direction of movement of the money:
$1000 is paid into the account (+ve)
$1061.68 is what you can take out of the account at the end of the specified period, thus -ve (even if you don't actually want to withdraw it at that stage).
Note that the opposite convetion is also used (e.g. in the 12C manual "The Cash Flow Sign Convention" p36):
$1000 is paid into the account, i.e. money you pay out (-ve)
$1061.68 is what you can take out of the account at the end of the specified period, i.e. money you receive (+ve).
Best regards.
Note: I do not work for HP, I just like playing with calculators :-) -
12c: Signature digest verification failure with SAML msg protection policy
Hi,
I am using the policy wss10_saml_token_with_message_protection_service_policy for Service Bus 12c proxy service and getting the error while verifying the signature digest. I am doing the testing using SOAP Ui.
I am able to understand it's an issue in verifying the signature digest but unable to debug and conclude the cause of this issue as i did the necessary setup. And using the appropriate keys for encryption and signing. Also tried overriding the policy configuration at policy level and Service bus end point level too.
Policy Settings are:
- Time Stamp included, Signing entire request body, no signing for SAML token and X 509 token.
- No signature encryption checked and kept default values for all other attributes.
Configured only Message Security section in WSM Domain Configuration and used JKS as the key store. Used the trusted certificate entry of client as signing alias and own public key as enc alias.
Following is the error stack trace i am seeing. Please let me know if there is any thing missing or any other insights into this issue. The logs generated by setting xml.debug.verify also did not help much. I am thinking the issue may be something to do with Canonicalization of XML.
Caused by: com.bea.wli.sb.security.wss.WssHandlerException: General web service security error
at com.bea.wli.sb.security.wss.WssHandlerImpl.generateInboundRequestBLE(WssHandlerImpl.java:1499)
at com.bea.wli.sb.security.wss.WssHandlerImpl.handleInboundRequestException(WssHandlerImpl.java:1457)
at com.bea.wli.sb.security.wss.WssHandlerImpl.handleInboundRequestException(WssHandlerImpl.java:1444)
at com.bea.wli.sb.service.disi.handlerchain.handlers.InboundWssPhase1DISIHandler.dispatch(InboundWssPhase1DISIHandler.java:107)
... 43 more
Caused by: com.bea.wli.sb.security.wss.WssException: oracle.wsm.security.SecurityException: WSM-00061 : Signature digest verification failure. The system property xml.debug.verify should be enabled for the details about the digest calculations during verification phase (note xml.debug.verify slows down the signature verification for very large messages).
Caused by:-
at com.bea.wli.sb.security.wss.wsm.WsmInboundHandler.handleRequestException(WsmInboundHandler.java:350)
at com.bea.wli.sb.security.wss.WssHandlerImpl.handleInboundRequestException(WssHandlerImpl.java:1442)
... 44 more
Caused by: oracle.wsm.security.SecurityException: WSM-00061 : Signature digest verification failure. The system property xml.debug.verify should be enabled for the details about the digest calculations during verification phase (note xml.debug.verify slows down the signature verification for very large messages).
Caused by:-
at oracle.wsm.security.policy.scenario.processor.Wss10MessageSecurityProcessor.verify(Wss10MessageSecurityProcessor.java:482)
at oracle.wsm.security.policy.scenario.processor.Wss10X509TokenProcessor.verify(Wss10X509TokenProcessor.java:301)
at oracle.wsm.security.policy.scenario.executor.Wss10SamlWithCertsScenarioExecutor.receiveRequest(Wss10SamlWithCertsScenarioExecutor.java:184)
at oracle.wsm.security.policy.scenario.executor.SecurityScenarioExecutor.execute(SecurityScenarioExecutor.java:642)
at oracle.wsm.policyengine.impl.runtime.AssertionExecutor.execute(AssertionExecutor.java:44)
at oracle.wsm.policyengine.impl.runtime.WSPolicyRuntimeExecutor.executeSimpleAssertion(WSPolicyRuntimeExecutor.java:515)
at oracle.wsm.policyengine.impl.runtime.WSPolicyRuntimeExecutor.executeAndAssertion(WSPolicyRuntimeExecutor.java:427)
at oracle.wsm.policyengine.impl.runtime.WSPolicyRuntimeExecutor.execute(WSPolicyRuntimeExecutor.java:374)
at oracle.wsm.policyengine.impl.PolicyExecutionEngine.execute(PolicyExecutionEngine.java:103)
at oracle.wsm.agent.WSMAgent.processCommon(WSMAgent.java:1270)
at oracle.wsm.agent.WSMAgent.processRequest(WSMAgent.java:563)
at oracle.j2ee.ws.common.wsm.SecurityAgentTube.processRequest(SecurityAgentTube.java:201)
at com.sun.xml.ws.api.pipe.Fiber.__doRun(Fiber.java:1136)
at com.sun.xml.ws.api.pipe.Fiber.access$100(Fiber.java:127)Please do let me know if anybody has insights into this issue. I am testing it from SOAP UI and i am completely stuck and can't proceed further.. We did face similar issue in 11g which was gone after upgrading to later OSB releases.
-
Hi
We have a requirement where the client wants only VAT to be posted in GL accounts and not the price.For this I tried free goods condition type R100 with AltCBV 28.But the VAT value is also coming zero. I want the VAT to be calculated on Pricing condition and then give 100% discount.
Apart from this I also tried to make pricing condition statistical and calculate VAT on it but then also system gives zero value for VAT.
Also wondering if the scenario can be addressed with Free of Change Dellivery.Hi
Normally in scenario where you are dealing with samples , there are cases you have to charge only TAXES / EXCISE part.
Here my SUGGESTION is you can handle this through a simple sales order process, where you have to configure a new pricing procedure.
1. Create a new document type to handle samples.
2. Create a New pricing procedure where you can keep the basic price condtion as Statistical and rest all same as wht is is there your main pricing procedure. Just juggle with the TO-FROM to capture the TAX part in the total.
3. Doc pricing procedure will help you to pick the new Pricing procedure
4. Now Process this as a normal sales order
5. This new document type will help you to have a proper reporting.
The only constraint here is USER has to punch a fresh order seperately for such scenario. He cannot give a free good in the same sales order which is used as standard.
The other way is you can configure a FREE GOOD Determination procedure as suggested where you need to then have your Single pricing procedure accomodating the same scenario.
Thanks
RB -
Hi Everyone
I used this in SP calculated column field.
=IF([Shift Sched]="1pm to 10pm","0",IF([Shift Sched]="2pm to 11pm","1",IF([Shift Sched]="3pm to 12am","2",IF([Shift Sched]="4pm to 1am","3",IF([Shift Sched]="5pm to 2am","4",IF([Shift
Sched]="6pm to 3am","5",IF([Shift Sched]="7pm to 4am","6",IF([Shift Sched]="8pm to 5am","7",IF([Shift Sched]="9pm to 6am","8",IF([Shift Sched]="10pm to 7am","8",IF([Shift
Sched]="11pm to 8am","7",IF([Shift Sched]="12pm to 9am","6",IF([Shift Sched]="1am to 10am","5",IF([Shift Sched]="2am to 11am","4",IF([Shift Sched]="3am to 12pm","3",IF([Shift
Sched]="4am to 1pm","2",IF([Shift Sched]="5am to 2pm","1",IF([Shift Sched]="6am to 3pm","0",IF([Shift Sched]="7am to 4pm","0",IF([Shift Sched]="8am to 5pm","0",IF([Shift
Sched]="9am to 6pm","0",IF([Shift Sched]="10am to 7pm","0",IF([Shift Sched]="11am to 8pm","0",IF([Shift Sched]="12pm to 9pm","0"))))))))))))))))))))))))
it was able to work fine however my issue is when i extract the information to excel and use a pivot table the table is not able to calulate the sum of the value for this field. Can you please help me with this. this is for an Attendance traker for Night
Differential pay for employees. they create a daily log of their shift schedule and if i summarize this in pivot the value in the calculated field for this is not getting the sum.
Thanks,
NormanHi Everyone
I used this in SP calculated column field.
=IF([Shift Sched]="1pm to 10pm","0",IF([Shift Sched]="2pm to 11pm","1",IF([Shift Sched]="3pm to 12am","2",IF([Shift Sched]="4pm to 1am","3",IF([Shift Sched]="5pm to 2am","4",IF([Shift
Sched]="6pm to 3am","5",IF([Shift Sched]="7pm to 4am","6",IF([Shift Sched]="8pm to 5am","7",IF([Shift Sched]="9pm to 6am","8",IF([Shift Sched]="10pm to 7am","8",IF([Shift
Sched]="11pm to 8am","7",IF([Shift Sched]="12pm to 9am","6",IF([Shift Sched]="1am to 10am","5",IF([Shift Sched]="2am to 11am","4",IF([Shift Sched]="3am to 12pm","3",IF([Shift
Sched]="4am to 1pm","2",IF([Shift Sched]="5am to 2pm","1",IF([Shift Sched]="6am to 3pm","0",IF([Shift Sched]="7am to 4pm","0",IF([Shift Sched]="8am to 5pm","0",IF([Shift
Sched]="9am to 6pm","0",IF([Shift Sched]="10am to 7pm","0",IF([Shift Sched]="11am to 8pm","0",IF([Shift Sched]="12pm to 9pm","0"))))))))))))))))))))))))
it was able to work fine however my issue is when i extract the information to excel and use a pivot table the table is not able to calulate the sum of the value for this field. Can you please help me with this. this is for an Attendance traker for Night
Differential pay for employees. they create a daily log of their shift schedule and if i summarize this in pivot the value in the calculated field for this is not getting the sum.
Thanks,
Norman -
If statement in Custom Calculation Script
I have 16 fields and if even one of them ="1" I have to list it in another field. I do not want to count or sum. If one of those fields has a 1 in it I just want the other field to display Y and if none have a 1 I want that field to display N.
Please help.
Thank you in advance~mjcYou need to write a compound logical statement to evaluate all of the values and that statement needs to evaluate to true or false.
Do you know how to write JavaScript?
Do you know how to enter JavaScript calculations into a form field?
For custom calculation of the text field I could write something like:
// define an array of the field names to check
var aNames = new Array("Text1", "Text2", "Text3", "Text4",
"Text5", "Text6", "Text7", "Text8",
"Text9", "Text10", "Text11", "Text12",
"Text13", "Text14", "Text15", "Text16");
// define a logical variable that is true if any field has a value of 1 - default is false or no field has a value of 1
var bMatch = false;
// value for text field
var TextValue = 0;
// logical value of field being equal to 1 test
var FieldIs1 = false;
// loop through all the fields and test the fields value
for(i = 0; i < aNames.length; i++) {
// logically OR the result of field i value equal to true with bMatch
// get the value of field
TextValue = this.getField( aNames[i] ).value;
// test the value of the field
FieldIs1 = Number(TextValue) == 1
// logically OR the 2 values
bMatch = FieldIs1 | bMatch;
} // end field processing
// set the field value
if(bMatch == true) {
event.value = "Y";
} else {
event.value = "N";
You will need to change the field names to match your fields. You can add more field name or remove field names as needed and the script will adjust for the number of field names. -
If statement in calculated batch characteristic (dependencies)
I have a little problem with calculating a certain batch characteristic.
The situation is the following:
I have batch char A, batch char B and batch char C. Batch char C is the result of the sommation of char A and B. The problem I have now is that batch char C only should be calculated when batch char A and B are different from 0.
I have a custom build interface that imports QM data to the batch chars. Default, all my batch chars are set to 0 so if I just say $self.charC = $self.charA + $self.charB, I always get a value.
Is it possible to some sort of IF statement to check if the value is different from 0?Dear,
You need to try with variant table
take all the combination and enter in a variant table and see the result...it works
example
A B C
0 0 space
0 1 sapce
1 1 space
I hope you got it -
Pension not calculated when EE is hired mid-month
Hi All
Please suggest for the following....
When an Employee is hired in the middle of the month, the system doesn't calculate Pension Contribution.
Like if an EE is hired on 10th April. The system will calculate all payments & deductions, but it is not calculating the Pension Contributions.
I am maintaining IT 169, 171 for Pension Contribution.
The problem I found behind this is.....(WIth the help of an ABAPer)
-: System checks the Payroll Period Start Date with the Org. Assignment start date. When it doesnu2019t match, the system does not calculate the Pension Contribution.
For the time being I solved this through the following action -: In debugging, I canceled this condition (skipped this check). Then it calculated the Pension Contribution.
But, this is not the right solution for achieving that as we are changing standard SAP coding.
Please suggest any solution for the same.
Thanks & RegardsIf your schema has p0169 with BEG that will happen, try put below Param1 which fits your requirement.
BEG
Infotype records are evaluated on the payroll period begin date.
No changes within the current payroll period are taken into
consideration.
No proration of contributions takes place, even if the record ends
within the current payroll period.
END
Infotype records are evaluated on the payroll period end date.
No changes within the current payroll period are taken into
consideration.
No proration of contributions takes place, even if the record begins
within the current payroll period.
CHK
Infotype records are evaluated on the payroll check date (the pay date),
regardless of whether the check date falls into the payroll period
itself.
A record whose validity starts after the end date of the current payroll
period is still evaluated if the check date (which lies in the future)
falls within the validity period of the infotype.
FRST
Infotype records are evaluated if there is any intersection of plan
infotype and payroll period. The first intersection is taken to
determine the full period deduction amount which is stored without
proration.
LAST
Infotype records are evaluated if there is any intersection of plan
infotype and payroll period. The last intersection is taken to determine
the full period deduction amount which is stored without proration.
Maybe you are looking for
-
How can I download the Additional Content to a separate hard drive?
Looks like you are forced to download the 36GB of content locally - is there any way to point to to another drive? If not, after downloading locally, can you move it to another drive and will Logic X still see it?
-
DELETE query takes long time more than 30 min
Hi I have delete query as below.It takes 1300 sec to execute .Please let me know how to reduce the time of execution.I have indexes on both the columns jdoid,jdoversion of deletion. DELETE FROM SIT7016.DEVICEINTERFACE WHERE JDOID = :1 AND JDOVERSION
-
Hi, I am facing a issue with an inbound purchase order change IDOC (message type: PORDCH). I am getting the following error: FM VENDOR_MASTER_DATA_SELECT_15 ; no partner functions found for vendor VENDOR_MASTER_DATA_SELECT_15 1. The vendors are c
-
I upgradeed to OSX Mavericks, and now I can't open a PDF by simply double-clicking on it. I need to open Acrobat, and then do File/Open. I also can't create a PDF from multiple files, it hangs up on "checking security".
-
Dear Experts, I am quite new to authorizations and in particular to SEM-BCS authorization. So I would be happy if you could help me with the following requirement: We have to setup an authorization concepts for SEM-BCS. Among others we want to setup