HP 6840 no longer sees the wireless network.

I recently updated the firmware on my Airport Extreme and now my HP 6840 wireless printer nolonger sees the network. I have run and rerun setup, rebooted everything even tried using and older MAC to run the obsolete setup software to no avail. Printer works when plugged in to the ethernet, Airport works but the the printer will nolonger funstion wirelessly.
HP said it was obsolete, Apple said it was an HP firmware issue and I am frustrated.... Any suggestions?
msm

I did have a very long discussion with HP Support but this printer is no longer supported by their phone support. The tech gave me a lot of ideas but none worked. I have determined that one of two things has happened:
1. The recent firmware upgrade to the Airport Extreme has caused the problem, which you think could be resolved with a new driver, but nothing Apple or HP supplies with work, or
2. The radio itself has failed. This I doubt, but every attempt to re-enable it does not work.
I have the printer plugged into the router and it is working but the location is not optimum for our home. No worries, as I mentioned before, I have ordered an inexpensive wireless printer server and should have it back in line by this afternoon and back in my home office where it belongs.
Thanks for the converstaion!

Similar Messages

TS1559 Since upgrading my iPhone5 to the newest iOS (6.1.2) I can longer connect to WiFi. It sees the wireless network but will not connect.. Other devices in my home that weren't upgraded can connect just fine.

Since upgrading my iPhone5 to the newest iOS (6.1.2) I can longer connect to WiFi. It sees the wireless network but will not connect.. Other devices in my home that weren't upgraded can connect just fine.

I had the same problem. I did the reset networks on my iPhone & it did not work. My husband read somewhere that changing the channel on the router to manual & selecting the highest available channel number might help. I did that & it solved the problem. I have not had the problem since.

My old PowerPC G4 no longer sees any wireless networks

My old PowerPC G4 no longer sees any wireless networks. The PowerPC and my new iMac was powered off for a week. When I powered them on, the iMac found the usual wireless networks that are seen around here but the PowerPC did not see ANY! Even though they sit next to each other!! The G4 worked fine before and was connected to the internet.
The G4 has an AirPort card in it and IS enabled. Is the problem with the card (how do I verify?) or did something get turned off on the re-boot?
BTW the AirPort card does shows up in the system info and has firmware version 9.52 but states that "wireless network not available" under the Current Wireless Network.
How do I fix this?
Please Help!

As this is an old G4, I presume you have a PCI network card.
I had a similar problem on my son's old G4. After a lot of messing around thinking it was a software problem, I discovered that the antenna was damaged and did not make a good connection to the card. I could get it to work intermittently by pushing it on. The solution was to buy a new card.
So try manipulating the antenna connection at the back of your mac to see if you can get a signal.

MBP+WinXP won't connect to network. It sees the wireless network but stops.

I've been fighting this for two solid days.
Time Capsule takes an address automatically from my router/modem. The MacBook Pro connects wirelessly thru Time Capsule to my ethernet network and the internet. No problems.
Windows XP on the same Mac wirelessly sees the network and reports its name. That's where it stops. The Windows "Choose a wireless network" dialog has the network name highlighted and the annotation, "Acquiring network address", presumably from the modem router. Nothing is happening.
What do I do next? All I want to do is join my existing wireless network from Windows. I have never been offered the opportunity to join it... I assume that at some point I will be required to provide the network WPA/2 password but that never happens.
I am totally bamboozled! The old Airport Extreme BS gave exactly the same problem so I have to assume that Windows is the problem. No, I do not know Windows very well.
BTW, Windows connects to the network and the internet okay via ethernet.

Never mind....
Repeating the same steps over and over I eventually found Windows asking for a network key. I don't have any idea where to get that key, so I provided my wireless network password. That worked. And the MBP+WindowsXP did in fact connect to the internet and my network. Problem solved.
I dare not interfere with anything now because if I mess it up again... I have no idea how I got Windows to ask for the password after sitting there for many many hours stating it simply needed a network address. IT DID NOT NEED A NETWORK ADDRESS — IT NEEDED MY PASSWORD!
I'll never understand Windows. It uses different terminology for everyday items and functions; it's system of step by step support guides suggests moves that don't agree with the Windows dialogs or anything that appears on the desktop.
For me Windows is about the most confusing, hated thing on the planet.

IPod no longer sees ANY wireless networks

Last week I noticed that my Touch would regularly lose its connection to the internet (the little wireless indicator would disappear and the only way to get it back on was to go into Settings > Wi-Fi Networks > "Choose a Network"). Then it started getting worse. I would follow the above process but would see NO networks. I would turn the Wi-Fi slider off, then on, and usually on the first or second try it would display networks. Somewhere in this process the iPod quit asking me if I wanted to join availabe networks in the app (the little pop-up of availabe networks quit appearing). Friday night a friend called to ask me for a phone number and I ran Safari, got online via the above, lengthy process and little did I know, but that'd be the last time my iPod would go online.
Saturday morning I woke up to check my email via iPod and it said no networks available. Normally in my apartment I can see 3, one of which is mine. I manually entered my SSID and was informed that iPod was unable to connect. Then I walked over and rebooted the router, still no luck.
The following also had no results:
1. I "Reset network settings."
2. I "Reset All Settings."
3. Restore from backup via iTunes.
4. Turning off "Fetch New Data"
The following allowed me to see my home network exactly one time (but still didn't let me connect.)
1. Settings > General > Reset > Erase All Content and Settings
2. Restore from back-up
3. Settings > Wi-fi
My network SSID appeared exactly one time, though neither of the neighbors wireless did. I clicked on the name, and got "unable to join..." at which point the SSID disappeared from the list. (which now only says, "Other..." and refuses to join my network when I enter the SSID and the iPod is SITTING ON THE ROUTER!")
I'm now at work and the WPA network at work also doesn't show up. Normally from my desk I can see 3 networks.
At home, I've got (at this point) an unencrypted, SSID-broadcast, non-MAC filtering network that works for 5 other machines in the house. According to apple my Serial Number is not worthy of free technical support so I'm appealing to the masses here with some hope that this is a simple procedure that I'm missing. If this is really a hardware failure of the iPod at 11 months there's some serious quality control issues!

I've got this exact same issue which just started for me last night (running 2.0.1 software). I was unable to pick up my own home network or my neighbours which always shows up in my list. I reset the iPod touch but to no avail. I then did a factory restore on it today but that didn't fix the issue. I phoned Apple Support and within 5 minutes he was filling out a despatch note and arranging for a courier to come and pick it up within 3 working days for repair. Luckily I'm just within the 1 year warranty as I've had the iPod touch for 11 months. Hoping it can be fixed quickly.

Need help here! I'm out of options. Computer can't see the wireless network

Sorry for the novel, but I have to tell you what is going on with my computer. I also need to vent because I’m extremely frustrated. I want to make sure I give as much info as I can we can get this fixed. I’m done with trying to figure this out on my own!!!
I’m having a major issue with the wireless network connection on my desktop. I’ve tried everything and I can’t figure out what it’s doing.
First of all, my wireless router is set up correctly (according to the Sticky), has active security, and works fine. It has nothing to do with the router. I’m sure of it.
Here’s a quick history:
When I was at my first residence in Chicago and bought a Linksys wireless N router in May 2008. My computer was about 30 feet away from the router and everything worked fine. Always found the router and never lost connection.
I moved to a new place in September 2008 and used the same router, computer, etc. at my new place. The computer was only about 7 feet away from the router this time, but I used the wireless connection instead so I wouldn’t have a network cable lying across the floor. At first everything worked fine. No issues. Then, one day out of the blue, my desktop lost connection with the router. My router didn’t even appear as an Available Wireless Network. I rebooted everything and that seemed to fix it. OK, issue fixed, right? Wrong. It did it again the next day. I rebooted everything, but it still couldn’t find my router. It did see lots of other wireless routers in the area though so I know the wireless card was working. It just didn’t see my router.
This went on for a while. Sometimes it would see my router and connect then it would lose it again. I thought maybe it was the router going bad. Well, I have a notebook computer too so I tried it. It has found my router every time and has never lost connection. I had it sitting on top of my desktop even to see if there was some sort of dead spot in my condo, but the notebook found my router just fine.
Sometimes my desktop would see my router, but it wouldn’t be my network name. It would call it “Home” or something. I know it was my network because it was the only network with maximum (Excellent) signal strength. I’m thinking it must be some sort of association issue. For some reason it doesn’t associate my router as an available network. I don’t understand that.
I tried everything: Ad Aware, Live OneCare, registry cleaners, driver updates, restore points, pretty much anything I found in the forums. Nothing worked for long if at all. It’s like my desktop only finds my router when it wants to. Note: The only thing that would work sometimes was if I clicked “Repair.” Sometimes that would work. I finally gave up and connected my desktop via network cable and unhooked my wireless card. I never lost connection as long as it was hard-wired.
The drama continues. I recently moved to Iowa and set up my network here. I’m using the same router, same desktop and wireless card, same notebook computer, etc. I went ahead and tried the wireless card on my desktop again. It worked just fine! No connection issues at all. It connected and stayed connected. I thought, “Well, that’s strange. It must have been something with the condo in Chicago. Oh well!” It worked fine from February 5 until March 10. Now it’s doing it again!!!! The notebook is about 3 feet away and sees the router just fine.
Here are the facts:
I’m using a Linksys WRT300N Wireless-N router.
I’m using a Linksys Wireless-N PCI WMP300N Adapter (about 18 months old).
I’m running Windows XP on the custom built desktop and Windows Vista on the HP notebook.
I built this computer about 5 years ago and have not done any major upgrades for 2-3 years. The only thing I added was the wireless card. I also changed out the HD in January 2009 and did a data migration right before I moved to Iowa in February. All of the networking issues were going on well before I did the data migration though so it has nothing to do with that. In fact, I had my computer hard-wired into my router at the time of the data migration and the wireless worked fine (for a little while) after I moved to Iowa. So if anything, the data migration seemed to help with my wireless connection.
All drivers are up to date.
Using Windows Live OneCare and have run complete scan: nothing found.
Using Ad Aware and have run complete scan: only found cookies and deleted them but didn’t fix issue.
Ran WinsockxpFix but that didn’t help.
Ran TweakNow RegCleaner Standard but that didn’t help.
Right-clicking the wireless icon, I try to view Available Wireless Networks. The window comes up and shows me other wireless networks in the area (2 available right now), but doesn’t show my network at all. I click “Refresh network list” and 1 or 2 of the other networks will come up, but mine is still not shown.
I’ve clicked “Repair” and get this message: “Windows could not finish repairing the problem because the following action cannot be completed: Connecting to the wireless network.”
If I go to Control Panel, there is a Wireless Configuration Utility program from Broadcom. When I open that here is what I find:
It is not managing my wireless networks.
Under the “Wireless Networks” tab I see my Network with an “X” over the router icon to the left of it and a locked security icon to the right of it.
No information under the “Link Status” or “Statistics” tabs.
The “Site Monitor” tab shows my wireless network and the other 2 networks in the area (although they drop in and out because of signal strength). My network is always present even though the signal strength bounces up and down. This tab shows that my network is secure, 802.11 is g and n, speed is 270 mbps, Channel is 9, and Signal bounces from orange/red to green. Data encryption is (m)TKIP, TKIP, WPA-PSK.
I was going to use my notebook to post this message since it has been connected for 2 days without ever losing connection. It shows Very Good signal strength and is about 3 feet away from my desktop.
Update: My desktop just connected to my network after sitting there for 2 hours. Good to Very Good signal. Broadcom tool shows the connection and now has information in the Link Status and Statistics tabs.
Cancel that. It just lost connection again. It was only connected for about 5 minutes. There is no change in signal strength according to Broadcom though. In fact, Broadcom shows better signal now that I lost connection.
Now, it just connected again (on its own) after sitting there for 10 minutes! I’ve been surfing the web on my desktop for 45 minutes now and I’m using my desktop to post this message. What the heck?!!! This is what it’s like. Aggravating huh?
Well, that’s all I can think to write. What else do you need? Can anybody help me with this?
I’m confused. Please help!
Thanks a lot!!!
Jake
Message Edited by JakeT on 03-12-2009 02:54 PM

Thanks but it's just my desktop that doesn't see it though. My notebook sees it everytime, even at the same exact time that my desktop doesn't see it. For example yesterday when I was typing up this post, I was typing up the post on my notebook because my desktop didn't see the router. I don't think it has anything to do with the router actually, but I wanted to see if anyone on here has encountered this issue before. Other forums have similar issues but I've tried all of the fixes I found elsewhere and they didn't work.
Any other ideas?
Thanks!

My iPhone 5S no longer sees my wireless printer via bluetooth

my iPhone 5S no longer sees my wireless printer via bluetooth. All it does in Settings is continually search for devices. I've rebooted the phone, as well as the printer. I even sat next to the printer with no luck. It did find the printer when I initially set it up.

Did this work for you in the past?
ios does not support bluetooth printers without extra software.
Helper app -- /print n share
Print directly to the widest range of network or WiFi printers available in any app. Alternatively print via your computer to ALL printers including USB & Bluetooth printers. View read and display large PDF, Office & iWork files. Easily transfer & store files from the Cloud or your computer.
https://itunes.apple.com/us/app/print-n-share/id301656026?mt=8
You need to buy the right printer.
The iPad uses a print technology called AirPrint. Airprint is a particular communication protocol that flows over WiFi. So, having a WiiFi printer isn't sufficient. The printer needs to be of an Airprint variety of WiFi.
For a comprehensive list of links,
   see Texas Mac Man list:
     https://discussions.apple.com/message/21291967#21291967
   or
     http://ipadhowtouseit.com/ipad-printing/

How do I use a wired computer on the wireless network?

I want to hardwire my desktop to my wireless router. I have a wireless adapter and my computers work fine on the wireless network. If I try to plug in the ethernet cable to the router and disable the wireless adapter, it doesn't work. The light lights up on the front of the router saying that the ethernet cable is plugged in and the 1394 network connection is enabled in the "network connections." However, I cannot ping the router when using the ethernet. On the desktop computer, I look in "view workgroup computers" and there are no computers listed there. On the back of the computer, there is a light that lights up when I insert the cable, so I know the computer has detected there is a cable plugged in there.
They way I set up my wireless network is by using XP's tool under network tasks called "set up a wireless network for a home or small office" (which is found in "My Network Places." I don't know how to combine a wireless network with a wired network. Please help me.
I am using WRT54G. We don't have broadband installed yet.

Correct…I would not mess w/ the bios. Do you have an extra cat5 cable long enough to plug into the back of your router to the back of your PC? Hopefully, it was not taken out when the wireless NIC was installed. Do you see a place to plug in the cable on the back of your PC? It looks like a phone connection jack/ modem, only bigger. If not, what kind of machine, OS (Win 2K, Win XP, etc).

My new Canon Pixma 7250 wireless printer can no longer find my wireless network. My MAC is, Yosemite 10.10.2. I've run diagnostics and Canon LAN printer setup routine many time. Is there a solution? Can anyone help?

My new Canon Pixma 7250 wireless printercan no longer find my wireless network. (It worked fine until recently) I have a Yosemite 10.10.2. I've run diagnostics and the Canon LAN printer setup routine many times. Is there a solution? Can anyone help?

Turn of the MG and unplug the power cord. Leave it off for about a minute and then reconnect the power cord and turn the power back on. Wait while the device attempts to reconnect to your wireless network - the blue wifi symbol on the MG will flash and then stay on once it has connected. If it keeps flashing then you will have to reconnect the MG to your wireless access point via the control panel on the MG.

HP8500A all-in-one can no longer scan thru wireless network but prints fine.

HP8500A all-in-one can no longer scan thru wireless network but prints fine. Have used this device several times over past 2 years on different wireless networks (at home) but usually at some point I lose wireless scan function but maintain wireless Printing. I used to be able to reload the software and resolve the issue but now in this "new network" cannot get wireless scanning to work. Setup software; original software (CD) and current download as well as "Print/Scan Dr" hangs-up at "network check" for hours. Compaq laptop, Dell Laptop, Cell phones and Roku work fine thru network. Scanner works fine with USB to Laptops.

Which model Epsons are they?
I'm assuming you're using Yosemite (OS X 10.10), and that the problem developed when you upgraded from a previous OS.
(Your profile says 10.6.7 BTW).
Maybe the scanning function is not compatible with Yosemite.
You could try a few things:
reset your wifi system:
power down everything: modem, router, computer, printer/scanners.
wait a minute.
power them all up again, in that order: modem, router, computer, printers. Let each power up completely before going on to the next.
try a factor reset on your printer/scanner (if there is such a function). You'll have to check your manual for how. If you do that you'll have to enter the wifi password in your printer/scanner, assuming you have security on your network.
uninstall any printer manufacturer "utilities" that are on your Mac, and try Image Capture again.
If it is a compatible software issue, you could try VueScan, but I've never needed to use it.

No longer detetects any wireless network

Hi
My macbook was correctly connected to the Internet via my wireless network, and then it suddenly disconnected. It no longer detects any wireless networks (and there are quite a few usually!)
I tried to turn airport off & then back on, but no change.
I then tried to reboot my macbook, but no change either.
When it searches for wireless networks, it is very slow (sluggish).
I also booted on Windows 7 (dual boot), and it has *exactly the same* problem. Leads me to believe that it is a hardware problem, more than a software one..
The only recent change: I moved from the UK to France few days ago => new ISP & new router (but I doubt this could be the source...)
Is there anything I can do?
Replace the wireless card?
Thanks

By the sounds of it, I've been having exactly the same problem. I will be using my macbook and suddenly the airport will drop out for no reason. Sometimes I can reconnect but often I'll have to try a dozen times or more, with the connection timing out each time. I've actually set up two differently named wireless networks at home to solve this - for a while, if one dropped out, I could reconnect to the other one. Even this has now stopped working. I've tried flicking airport on and off, restarting the airport base stations, I even have one of the wireless networks configured as WDS sending to an airport base station within a couple of metres of where I normally use my machine. Nothing works. I've tried deleting ~/library/preferences com.apple.internetconfig.plist and com.appleinternetconfigpriv.plist and rebooting - for a few times that would fix it, but not any more.
The strangest thing, though, is that if I switch user accounts, I can access the wireless networks again no problem.
It's almost like there's something that needs flushing in the user account's wireless settings - a buffer, or a cache, or something. It'll generally only happen once I've been using the machine for a sustained period of time.
I'm running 10.5.8 with Wireless Card Type: AirPort Extreme (0×168C, 0×86) Wireless Card Firmware Version: 1.4.16.2 if that's of any help to anyone.

This AirPort base station was unable to extend the wireless network.

I have an AirPort Extreme in the lounge connected to BT infinity.
I also have an airport express in the kitchen connected to a stereo system.
I have had this set up for around 12 months.
The airport express will not extend the wireless network.
I reset it, restart, factory reset etc and it will work fine for around 3 days, then I get the same error message saying
This AirPort base station was unable to extend the wireless network. Make sure the wireless network you’re trying to extend was set up and is working correctly, that you entered a matching wireless network password into this device, and that this device is in range of the wireless network.
The express is situated easily within range of the extreme. And the airplay between those two, my iMac and two apple tv's works pretty much as it should.
Can someone please shed some light on this?
Maybe I have it in a wrong setting or summut....

G Beach wrote:
I am also experiencing a recent failure in my Airport devices no longer extending my wireless network.
My Aiport Express and second Airport Extreme were extending my wireless network for more than a year
The only change that has taken place lately is that the firmware for both devices was upgraded to 7.6.4, however the upgrade was only in response to trying to resolve this problem. Needless to say, the firmware upgrade did not resolve anything.
If I didn't know better, I'd have thought I wrote the above.
I have a TC from a few years ago (last one before the tower, I think), plus the older AEBS that it replaced extending the network, plus a 1-year-old Express also extending. I had upgraded them all to 7.6.3/4 when it came out, but reverted them all to 7.6.1 when everything went crapways (others having the same issues of the LAN regularly croaking), and didn't bother upgrading again since.
Today I just tried 7.6.4 on all of them, and it seemed OK at first with green lights all around in Airport Utility. Then I made one change, which was to enable 5Ghz on the main AEBS/TC only (the express doesn't need it, and the older AEBS can't do it).
The latter two started flasing amber and giving the "unable to extend wireless network" error message.
So I'm wondering if you are similarly using 5Ghz?

Ethernet port as a bridge to the wireless network

*Is it possible to use an Ethernet port in MacBook as a bridge to the wireless network* and connect another device to it that will have access not only to the Internet, but also to other services, eg. files on another computer connected to the network wirelessly.

The short answer, would be Yes.
The longer answer requires setting up the computer in the correct
way to do so; and hope that any advice to going there was followed.
And knowing more about your hardware situation may yield better
or easier answers; a better solution to using all the computers.
You can share a network connection through use of settings in the
appropriate System Preferences panels. Other sharing preferences
would probably have to be checked and if necessary, changed.
I never change anything that just works, without good reason, and
so far, since I have no need to share between my computers by wire
or wireless, I have not done so. I do have files on external hard drives
and on USB Flash Drives, and can put stuff on CD & DVD media.
Given that, I don't network my computers over AirPort, Ethernet, or
by FireWire, etc. But others here do. Your HelpViewer in the Mac
can tell you how to network or share internet over ethernet, etc.
More information on your situation is needed to propose answers.
PS: Information you posted in another location would be relevant to
getting a reply here, too... in reference to this post:
http://discussions.apple.com/message.jspa?messageID=10804230#10804230
Good luck & happy computing!
{ edited }

I have an ipad first generation. I am trying to connect to a linksys router and it is not finding the wireless network. what do i need to do?

I have an ipad first generation. I am trying to connect to a linksys router and the ipad is not finding the wireless network. What do I need to do? Thanks for your help.

Some things to try first:
1. Turn Off your iPad. Then turn Off (disconnect power cord for 30 seconds or longer) the wireless router & then back On. Now boot your iPad. Hopefully it will see the WiFi.
2. Go to Settings>Wi-Fi and turn Off. Then while at Settings>Wi-Fi, turn back On and chose a Network.
3. Change the channel on your wireless router (Auto or Channel 6 is best). Instructions at http://macintoshhowto.com/advanced/how-to-get-a-good-range-on-your-wireless-netw ork.html
4. Go into your router security settings and change from WEP to WPA with AES.
5. Renew IP Address: (especially if you are droping internet connection)
    •    Launch Settings app
    •    Tap on Wi-Fi
    •    Tap on the blue arrow of the Wi-Fi network that you connect to from the list
    •    In the window that opens, tap on the Renew Lease button
~~~~~~~~~~~~~~~~~~~~~~~~~
iOS 6 Wifi Problems/Fixes
Fix For iOS 6 WiFi Problems?
http://tabletcrunch.com/2012/09/27/fix-ios-6-wifi-problems/
Did iOS 6 Screw Your Wi-Fi? Here’s How to Fix It
http://gizmodo.com/5944761/does-ios-6-have-a-wi+fi-bug
How To Fix Wi-Fi Connectivity Issue After Upgrading To iOS 6
http://www.iphonehacks.com/2012/09/fix-wi-fi-connectivity-issue-after-upgrading- to-ios-6.html
iOS 6 iPad 3 wi-fi "connection fix" for netgear router
http://www.youtube.com/watch?v=XsWS4ha-dn0
Apple's iOS 6 Wi-Fi problems
http://www.zdnet.com/apples-ios-6-wi-fi-problems-linger-on-7000004799/
~~~~~~~~~~~~~~~~~~~~~~~
How to Fix a Poor Wi-Fi Signal on Your iPad
http://ipad.about.com/od/iPad_Troubleshooting/a/How-To-Fix-A-Poor-Wi-Fi-Signal-O n-Your-iPad.htm
iOS Troubleshooting Wi-Fi networks and connections http://support.apple.com/kb/TS1398
iPad: Issues connecting to Wi-Fi networks http://support.apple.com/kb/ts3304
WiFi Connecting/Troubleshooting http://www.apple.com/support/ipad/wifi/
How to Fix: My iPad Won't Connect to WiFi
http://ipad.about.com/od/iPad_Troubleshooting/ss/How-To-Fix-My-Ipad-Wont-Connect -To-Wi-Fi.htm
iOS: Connecting to the Internet http://support.apple.com/kb/HT1695
iOS: Recommended settings for Wi-Fi routers and access points http://support.apple.com/kb/HT4199
How to Quickly Fix iPad 3 Wi-Fi Reception Problems
http://osxdaily.com/2012/03/21/fix-new-ipad-3-wi-fi-reception-problems/
iPad Wi-Fi Problems: Comprehensive List of Fixes
http://appletoolbox.com/2010/04/ipad-wi-fi-problems-comprehensive-list-of-fixes/
Connect iPad to Wi-Fi (with troubleshooting info)
http://thehowto.wikidot.com/wifi-connect-ipad
Fix iPad Wifi Connection and Signal Issues http://www.youtube.com/watch?v=uwWtIG5jUxE
Fix Slow WiFi Issue https://discussions.apple.com/thread/2398063?start=60&tstart=0
How To Fix iPhone, iPad, iPod Touch Wi-Fi Connectivity Issue http://tinyurl.com/7nvxbmz
Unable to Connect After iOS Update - saw this solution on another post.
https://discussions.apple.com/thread/4010130
Note - When troubleshooting wifi connection problems, don't hold your iPad by hand. There have been a few reports that holding the iPad by hand, seems to attenuate the wifi signal.
~~~~~~~~~~~~~~~
If any of the above solutions work, please post back what solved your problem. It will help others with the same problem.
 Cheers, Tom

Apple TV 1st Gen can no longer connect to wireless networks

My Apple TV (1st Gen) has recently lost the ability to connect to either of our wireless networks at home. I rean the diagnostics at the reset screen and the Apple TV says it is performing normally. In the settings, whenever I attempt to connect to a wireless network, I am now only offered "Other..." as a choice. Proceeding to the next screen, I enter the name of the network closest to the Apple TV -- an Airport Extreme set up for 5 GHz that this Apple TV connected with daily up until 2 days ago. The Airport base station is perfoming normally, as my MacBook Pro can see it and establish a network connection without any difficulty. The issue is limited to the Apple TV. I did a Factory Restore, and now when I go to Wireless Network > "Other..." > Enter the name of the wireless network" the resuit is always the same, and error message stating: "There was a problem connecting to the network. Check your settings and try again. (-4)".
This message comes up almost immediately, without requesting a WiFi password -- suggesting to me that this Apple TV has lost the ability to connect to ANY wireless network due to a hardware failure.
Q: Has anyone else in the Support Community had a similar experience with their 1st Gen Apple TV, and if so, did you find a solution to it?
Note: When I first noticed the connction to this Apple TV had gone stale (greyed out in the iTunes Airplay Speakers list), and prior to doing the Factory Restore, I could play back iTunes content stored on the hard drive, but could not connect to the local wireless networks. I noticed that the Apple TV was running very hot -- it has alwasy run pretty hot to the touch.
If this Apple TV has died, I will get a 3rd Gen Apple TV, but wiill then have to work through the HDMI to Composite video + Audio issues, as this Apple TV is connected to our older (non-HDMI) TV.

Follow-up: Able to connect with ethernet cable, downloaded software updates, connected to iTunes, and synchec content.
Next, disconnected the ethernet cable. ATV1 froze and was restarted using the Menu + ( - ) combo on the remote. Re-ran diagnostics yeilds: Apple TV is working fine.
Restarted, then went to configure the Wirelss settings. Apple TV once again does not show either of the two wireless networks. Selecting "Other..." and entering the SSID yields the same immediate response:
"There was a problem connecting to the network. Check your settings and try again. (-4)"
No change on the wireless front :-( Bummer.
Looks like an ethernet connection is the only option left to continue using this Apple TV 1st Gen.
Thanks for your help. -- Paul

HP 6840 no longer sees the wireless network.

Similar Messages

Maybe you are looking for