HP 720c in windows 7 64bit "out of paper"
Added the driver for the 720 c I found on this site. Windows 7 shows the printer and says it is working properly. It is connected to the PC via a parallel port card in a pci-e slot. Shows on port LPT1 and no conflicts are seen. When I print to this printer the document shows in the queue but does not print out and after about 2 mins the queue shows "out of paper". I have also tried it as LPT2: with the same results. When I put the printer back on the XP machine it prints fine. Why do I get the "out of paper" error in windows 7 when it is full of paper?
Hello Talyn16,
Welcome to the HP Forums! I understand your concerns with your Deskjet 720C. Make sure this printer is plugged into a direct wall, not a surge protector.
We want to fix the "Out Of Paper" error message first before we move on. Please follow this HP document on 'Out of Paper' Error Message Displays on the Computer, and the Printer Does Not Pick Up or Feed Pape...
When performing a "Reset", leave the power cord out for more than 60 seconds.
Let me know how your progress goes.
I worked on behalf of HP.
Similar Messages
-
Error message on print window for Vista--"out of paper"--I just loaded paper...?
error message on print window for Vista--"out of paper"--I just loaded paper...?
What can I do to get it to print?hi there,
could you provide the community with a little more information to help narrow troubleshooting? Things like your printer model can help out a lot.
You can say thanks by clicking the Kudos Star in my post. If my post resolves your problem, please mark it as Accepted Solution so others can benefit too. -
Ipod Touch 4th generation 32G not turning on, not charging.
I have used multiple cords on both computer USB and wall USB converters. I let it sit there for over 20 min with each attempt.
It is not being detected by Itunes or my Windows 7 64bit OS. I have tried all 4 of my USB ports (both USB 2.0 and 3.0), with 3 different chargers.
Holding home and power button will not reset.
Tried taking it out of "DFU" mode but Itunes won't detect it, I didn't think that would work anyway.
NO DAMAGE, I have been very careful with it, aside from a few minor scratches. (that you can't even see unless the light reflects them)
My Itunes is up to date, as is my OS.
All I'm getting is a blank black screen. It has been working fine on this computer before. I have no idea what could have happened. I'm at my wits end here.See if you missed anything here:
- iOS: Not responding or does not turn on
- Also try DFU mode after try recovery mode
How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
- If not successful and you can't fully turn the iOS device fully off, let the battery fully drain. After charging for an least an hour try the above again.
- Try another cable
- Try on another computer
- If still not successful that usually indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order.
Apple Retail Store - Genius Bar -
No sound out of back line out MacPro Bootcamp 3.1 Windows 7 64bit
No sound out of back line out speakers.
MacPro Early 2008
Bootcamp 3.1
Windows 7 64bit
Realtek HD audio driver.
I have speakers plugged into the back line out.
They work in Mac 10.6.4 (as always) and in Parallels 5 Windows 7 using Bootcamp partition.
All other jacks work. In Realtek driver it shows nothing connected to that jack.
Anybody else have this issue?
Anybody else have solved this?Anyone at all?
Even if you don't have the issue yet have a similar setup. Maybe I can figure out if there's a driver update I may need.
BTW I KNOW others have this as I've seen this mentioned on other forums. What I do NOT know is whether it's "everyone" or there's something about systems that don't have this issue, I need to follow. -
Aero in Windows 7 64bit home premium does not work. Aero display selections are grayed out.
Aero in Windows 7 64bit home premium does not work. Aero display selections are grayed out. HP 600-1315xt.
Have tried everything I can find on internet and here on HP. None of the suggestions worked. Windows fixit for windows could not fixit. Any suggestions are appreciated. I can always use my disks and rebuild the computer. A last resort.Hi,
It might be the graphic driver not compitable with the graphic device. Has there been a change to the graphic driver?
One thing you can try is to uninstall graphic driver and download the latest from Windows Update (if you haven't tried this). Here are the possible steps:
1. Go to Control Panel->Hardware and Sound->Device Manager, uninstall the graphic card driver by right clicking and select "uninstall". Make sure the option "Delete the driver software for this device" is selected.
2. Reboot the system.
3. Go to Control Panel->System and Security->Windows Update, click on "Optional updates" and find the driver for g210 and do the update.
I work on behalf o HP.
Please click the white Kudos star to say thanks.
Please click Accept As Solution if you found my response helpful. -
Install JMF on Windows 7 64bit
Dear all,
After a lot of struggling (and a really mean a lot), I finally got jmf to work on Windows 7 64bit. I figured that I can better not let this information go to waste, so that's why I'm posting it here. I didn't really test the full capabilities of jmf on my platform yet, in fact I only tested those features that I needed for my application. As such I am able to successfully capture and record video clips from my build in webcam of my laptop.
First let me describe my platform:
Laptop: Samsung R590 (JS01)
Processor: I5 450M (64bit)
OS: Windows 7 64bit
Webcam: build in
Secondly I want to apologize in advance if the method below doesn't work for you. The reason for that can be that I had to try so many different things before I finally got it to work, so I'm not really sure which steps are necessary and which ones are not. So I tried to make a guide that only includes the necessary steps, but in reality I tried so much more, so if this tutorial doesn't work for you, please give me feedback, and we'll try to figure it out. :)
Step one: installation of java JRE/JDK
JMF will never work on a 64bit JRE/JDK, plain and simple because JMF is too old and doesn't support a 64bit JRE/JDK. Thus your first step has to be to install a 32 bit JRE/JDK on your system. (I uninstalled my 64 bit JRE/JDK first, but I don't now whether or not this is necessary)
Step two: download JMF with windows performance pack
Go to the jmf site and download the most recent jmf version, with windows performance pack. (This is - and will probably be forever - version 2.1.1e)
The link to the website is currently: [https://cds.sun.com/is-bin/INTERSHOP.enfinity/WFS/CDS-CDS_Developer-Site/en_US/-/USD/ViewProductDetail-Start?ProductRef=7372-jmf-2.1.1e-oth-JPR@CDS-CDS_Developer]
Step three: install JMF
Install the file you just downloaded in the normal way you would install any other program. But chose as installation path: "C:\JMF2.1.1e"
I think this is necessary because of the strict security policy in Windows 7, if you don't do this, I guess jmf won't be able to store capture device settings to your local hard drive. (But again, I'm not completely sure here, please verify this if possible)
After the installation, you don't have to do anything special to get jmf to work, so you don't manually have to set the JMFDIR, PATH and CLASSPATH (as is explained at the sun website), just skip those steps.
After the installation, reboot your pc.
Remark: I recommend you to install jmf as an administrator (but I don't now whether or not this is necessary). To do this, right click the installation file and select: "run as administrator'.
*Step four: register your capture devices*
First make sure that all your devices are working properly, I recommend you to use a program like Skype or something just to check whether your microphone is working or not.
Secondly, open jmfstudio, select 'file > preferences > capture devices', and press the button 'detect capture devices'. Normally you will have to wait for a couple of minutes now (because the determination of all the available video formats takes quite a while). Afterwards jmf should have found all of your devices, that usually looks something like this:
DirectSoundCapture
JavaSound audio capture
vfw:Microsoft WDM Image Capture (Win32):0
But this can vary according to your configuration off course. :)
*Step four: test your capture devices*
In jmfstudio, select 'file > capture' and select the video and audio combo and see if your webcam settings work. You should now be able to view and hear yourself.
*Step five: that's it, enjoy your jmf*
*Remarks:*
My development platform is currently netbeans 6.9.1 and I am able to write code, build it and run it with netbeans. I can also just run normal *.jar files
*Troubleshoot:*
If you get a dialog screen when starting your video capture device that looks like this: [http://www.alexandria.nu/ai/machine_vision/dual_cameras/SelectDevice.gif]
(With off course another name for the capture device), then that means that your capturing device is currently occupied by another program and you can't currently use it.
To solve this, make sure that no other application is using the webcam. For me even this was insufficient, but I managed to solve this by installing the latest drivers for my webcam from the manufacturing site of my laptop.
I sincerely hope this tutorial can be of any use for someone, feel free to give me comments/suggestions. And please post here if this works for you or not.
Greetings, MollyHi
sure I follow each of your steps, I uninstall all java verisones and installed a new java version 32-bit, I installed JMF in "C: \ JMF2.1.1e".
when all installing finished, works fine JMF only once, I do the tests, recognizes the device; shows the video, but when I close and open again JStudio don't works throws error, and therefore my apliación not working, always returns null the device -
Broadcom 802.11n Network Adapter not working on Windows 7 64bit
As the title suggests, my laptop (Alienware m17x) is installed with the Broadcom 802.11n Network Adapter and Windows 7 64bit Home Premium. I have had several other driver incompatibility issues with Windows 7, but those I have slowly been able to resolve. This however just cropped up after two months of successful use. Yesterday it started failing to connect to the internet, telling me that no wireless connections are available. I live in a dorm, and everyone else on my floor has successful wireless, including my Ipod Touch, PS3 and XBox 360. I called Alienware/Dell Support and we spent hours trying to fix the problem and all look well until I rebooted my laptop this morning and the same issue reappeared. When I reboot my laptop, all I get is a notification that no networks appear in range. If I uninstall the broadcom chip and let windows install it after a boot up it works until the machine is rebooted a second time. I have tried over a dozen windows 7 drivers for the chip, and about half a dozen vista drivers and they all have the same results, works on the first boot, fails every time after that
Just registered to say, on an Alienware M17x system as well running Windows 7 Ultimate, here is a link to a solution that worked exactly for me:
http://forum.notebookreview.com/alienware/436486-guide-properly-solve-wireless-connection-problems-m17x.html
All I did was section I.a. If the link is down, I copied the only section that I needed to follow out of this guide, in order to get my wireless to work repeatedly without having to uninstall the wireless driver every single reboot. Now it works perfectly,
already connected to a wireless network on startup.
I.a. Disable Device sleep on disconnect
Some newer Nvidia Ethernet drivers have a feature called Device sleep on disconnect. This is the culprit. Normally, it should only put the Ethernet adapter to sleep when the cable is disconnected, but it's buggy and thus kills the wireless connection as
well.
Follow these steps to disable this feature on your Nvidia Ethernet Adapter:
1. Open the Windows Device Manager by hitting Win+Pause, then click on Device Manager on the left side.
2. Double-click on Network adapters.
3. Double-click on NVIDIA nForce Networking Controller (yes, that's the wired Ethernet adapter indeed).
4. Click on the Advanced tab.
5. Select Device sleep on disconnect.
6. Set the Value to Disabled.
7. Click OK and wireless should work again (might require a reboot afterwards, but probably not). -
Itunes 10.2will not install amds on windows 7 64bit
I have spent the last two days on the Internet and apple support to try and install iTunes 10 64bit onto my new computer running windows 7 64bit.All I find on Apple support is about removeing and reinstalling not about amsd missing or not installing and uninstalling in a certain order and reinstalling, have done this more times than I care to say. iTunes 10 installs then rolls back and does not install the apple mobile device support msi.I have done everything suggested by support forums and everything requested by apple support and the final comment from them was if this doesn't work they don't know, not to great an answer.
I am now very frustrated and angry that a fault like this has not been solved by Apple, as I now have a new computer and a useless iTunes that will not sync my iPhone 4 or my iPod or my wife's iphone3gs or her iPod shuffle.
I don't know what to do now as my last resort I put the computer back to factory settings and it still did not work,sorry forgot to mention I extracted the apple mobile devise support .msi with winrar and tried to install it separately but still no luck,
does anyone out there have answer PLEASE PLEASE HELP ?hi
i've been having the same problem. spoken to online support, they made appointment for genius bar, tech guy seemed to know his stuff but this issue was unknown to him. they agreed to give me a knew phone, eventually told me on day to when i returned that they had exhausted everything and that it was a pc software issue. possibly i should think about getting a mac or using another laptop! they also said that iphone works fine on mac but that there are som many versions of windows that it was difficult to keep up.
handing out replacement iphones and tech guys not know that there is a problem with windows 7 surely isn't good for business
apple support... can you address this problem asap please. i have restricted use and would like to get the full benefit of using my iphone 4
thanks
ps word of mouth is a powerful. the number of people who are concerned about updating to iphone is growing and i've not been able to recommend -
Hello,
I have Windows 8, 64bit and Office 2010
I am trying to get the 'datepicker' (MonthView) ActiveX control toolbox in Excel 2010 as part of a Excel UserForm I have created. I have spent all day trying to find a solution for my problem.
I opened up the 'more.. ' but the MonthView/datepicker/calendar control is not listed.
I referred to some articles and confirmed that I do indeed have the mscomct2.ocx file in the C:\Windows\syswow64 folder.
I followed the instructions as above, opening up the Administrator Command Prompt and changed the directory to C:\Windows\syswow64 and typed in RegSvr32.
I received a popup screen confirming my registration was successful
Excel was closed. So I opened Excel and checked out the ActiveX Tool box and clicked on the 'More Controls', but there was no listing for the Microsoft MonthView control, (nor datepicker/calendar)
I then downloaded the latest Windows Common Controls 2 6.0 from the following site
http://support.microsoft.com/kb/297381
Copied the original file (2008) and saved it elsewhere on the computer for safekeeping.
Extracted the new mscomct2.ocx.
Under the C:\Windows\syswow64 I changed the original file properties to allow me to overwrite it with the new file. This worked … old file replaced.
I then registered the new file via the Administrator Command Prompt (as above) and was notified that it was successful. I rebooted pc and went back into Excel to find the MonthView in the
ActiveX toolbox, More Controls… and it still wasn’t there …
I would be very grateful if someone could advise how I can get this control and allow me to use it.
If I have left out any information that you need to resolve this issue, please advise.
Cheers,
TheShyButterfly
Hope you have a terrific day, theShyButterflyHi George,
Thank you for checking this out ... :)
I am using Office 2010 64 bit ...
I found the
mscomct2.ocx file originally within the C:\Windows\syswow64 directory (this was an original file .... which I expect was installed via Microsoft at the time of the Office installation.
As I mentioned above, I followed
the instructions (same as the ones you suggested), but still no go, even though it stated that the registration was successful ! :(
Why weren't these features included in the 64 bit ? ... yes, I read the article ... but ... so MS doesn't think that people/developers would be needing this in due course? I installed the 64bit version because I'm running the Win8 64bit version ...and
I deal with a lot of large spreadsheets and can't afford to sleep whilst they decide to load.
If MS included all the other ActiveX controls and some obscure ones, surely some bright spark could have thought that something as useful as MonthView should be included as 'basic' necessity when dealing with forms and sheets?
Perhaps you could pass the suggestion up the line .... there are a lot of other people out there having the same problem ... I found heaps when I was looking for a solution.
Sorry, I'm not having a go at you, but just incredibly frustrated .... the amount of lost productivity directly cause by trying to find a solution that doesn't exist ... it's been at least a good solid 24 hours.
But thank you for taking the time to review my post and your suggestion. It's unfortunate that because you are part of the organisation ... you tend to cop some slack from frustrated people like myself.
In relation to the pictures/screen dumps, 2 of them made it (I can see them in my post) ... one I deliberately left out because there was nothing on there that showed anything other than the rest of the 'More Controls' - nothing to do with the MonthView.
Please feel free to escalate this to the powers that be ... and hopefully enough people will join the voice so a change can be made (I can dream ... can't I?)
I've taken a screen dump of the Forms/ActiveX toolbox.
I don't know what the next step is ... I guess you'd be able to advise.
Cheers,
TheShyButterfly
Hope you have a terrific day, theShyButterfly -
Lenovo D20, Type 4155-21G With 5x1.5tb Raid 5, Windows 7 64bit install problem.
H
Id like to just document a current machine and works and see if any thing is glaringly wrong..
Above spec machine has an onboard marrvel 66xx raid card, a raid 5 volume has been created, total useable space is around 5.5TB.
The software in play here is the following..
Orignal Lenovo recovery disk set, this is Rescue and recovery boot disk 1, then the OS which is Vista 32 Business, the disk label is actual 64bit but its not 64bit its 32bit.
The machine finally has to leave with Windows 7 64bit ultimate.
I have looked into the upgrade paths and so on and basicly you need vista 64bit ultimate in theory, certain hacks are possible such as renaming the os level or name via the registery, but this is dirverting from my post.
Here is what has been done and what has happend.
20th Jan.
Start of day.
Raid 5 volume created.
Factory recovery completed windows vista business 32bit.
Attempt to upgrade Windows vista business to Windows 7 ultimate from with in windows, windows 7 alerts this is not a compatable system etc.
At this stage since the 64bit upgrade is not possible from the known good lenovo state (lenovo vista business factory desktop etc) the second disks in the "Windows 7 32bit + 64bit any time upgrade package was ran.
The 32bit version of the Windows 7 ultimate was ran, this did complete sucessfully.
The 64bit version of the windows 7 was attempted once more from with in the newly installed Windows 7 32 bit but again this upgrade route is not supported.
At this stage a custom install was completed (which means a fresh install which wipes the drive) / fresh install, of the windows 7 64bit any time upgrade disk.
For some reason the Windows 7 64bit any time upgrade key failed to be accepted.
At this stage a second engineer repeated all steps completed to verify and on the second go around the FRESH install of Windows 64bit any time upgrade (stand alone install / custom etc) the key worked!..
This is were it gets interesting.
Lets recap, we have a D20 with 5x1.5tb sata hard drives in raid 5, all on the onboard marvel raid card.
Windows 7 64bit has been sucessfully installed, and of course the next step is to install the lenovo system update tool. (version for windows 7, I understand this is fully 64bit compatable..)
This was completed and pc doctor and one other misc application install, the system requested to restart and then ....
The raid BIOS of the marvel card reported that the raid had become degraded..!!
An inspection of the onboard raid information results that the disk 0 of the 5 disks, was no longer assigned to the RAID 5, with teh remaining several disks still "assigned".
At this stage the only option is to delete the raid five array and recreate it.
This has been done and the factory recovery process has once again been restarted and an attempt will be made to perform the custom install with hopefully the windows 7 64bit any time upgrade install detecting the previous version although I would say that it would not need to detect anything since this is now longer an upgrade but a custom fresh install.
Further information.
There is a System bios update from the 5th of Jan 2010, this has been burnt to cd and will be applyed against the machine shortly.
We have had some conversation about just how it is that a disk can fatally pop out from the raid five volume like this, was it a coincidence that it coninsided with the power cycle process dirrectly after the system update installation?
Tommorow a Windows 64bit OEM package will be applied against this machine and since we have the relivant driver file for the onboard raid card (sourced from the drivers and applications lenovo recovery disk set), there should be less of a problem in key acceptance.
Kind of a werid situation, what looks like a possible hardware problem and a stupid microsoft upgrade qulification problem.
Is there any thing stupid I have over looked?
Thanks, sorry for the long post but this is the story in full.
Note from Moderator: Fixed formatting issue.21st Jan..
The D20 has sucessfully had vista business factory reinstalled and then Windows 7 64bit installed.
Dirrectly after the Windows 7 installation and power cycle, one of the five 1.5tb hard drives have dropped out of the raid, visable as "DEGRADED", uppon further inspection via control m, the middle drive (not drive 0 as before) drive 2 (0,1,2,3,4,5) has dropped out and is not marked as assigned, it is marked with no label or free.
This is high strangeness, it is my understanding that the RAID technologies are transparent to the OS so it should not be in any way the Windows 7 install triggering this, the last occurance was also during a Windows 7 power cycle but dirrectly after the system update tool being installed.
At this stage it would appear that Windows 7 64-bit used in conjunction with the supplment driver disk marked as (drivers and apps, windows xp vista, windows 7) is not able to complete and remain stable.
I suspect a possible driver issue but if this was the case surely the windows 7 install would not progress past the first installation point where the driver disks is required to actually use and see the array via the controler.
I will update this thread with more information as it becomes available.
Machine delivery eta to customer is tommorow so this is not good. -
Error starting analytics - OBIEE 11.1.1.6 on Windows 7 64bit
Hello All -
I installed OBIEE 11.1.1.6 on Windows 7 64bit with out any errors. I am facing problem starting up the analytic's page, It is struck at the 500 Internal server error page. I opened up the enterprise manager to check whether all the services are up and running, but i found one of the service is down making it to 67-33%. BI Core application is down and when I opened it, all the services are down. BI server, BI presentation services, BI scheduler..all are down. I tried to restart all the services but in vain.
I have installed Loopback adaptor before staring the OBIEE installation, Checked the host file to have the ip address and machine name, Checked the OPMN status via cmd, all are alive. I am unable to figure out why I am getting this error. Below is the log file
Any help is greatly appreciated...Thanks for your time..
ECID bc7431c56d947d4e:-8f79716:137ed97154c:-8000-0000000000000135
Message OPMN.queryProcessStatus failed with the following exception
Supplemental Detail oracle.as.management.opmn.optic.OpticBadConnectException: Could not get secure socket for host 10.0.0.6 and port 9501
at oracle.as.management.opmn.optic.OpmnSSL.getSecureSocket(OpmnSSL.java:52)
at oracle.as.management.opmn.optic.OpmnPhone.dialOpmn(OpmnPhone.java:733)
at oracle.as.management.opmn.optic.OpmnPhone.getSocketForCall(OpmnPhone.java:455)
at oracle.as.management.opmn.optic.OpmnPhone.makePhoneCall(OpmnPhone.java:315)
at oracle.as.management.opmn.optic.OpmnPhone.request(OpmnPhone.java:270)
at oracle.as.management.opmn.optic.OpmnQuery.getBuf(OpmnQuery.java:482)
at oracle.as.management.opmn.optic.OpmnQuery.getDom(OpmnQuery.java:602)
at oracle.as.management.opmn.optic.OpmnQuery.getProc(OpmnQuery.java:750)
at oracle.as.management.mbeans.opmn.Opmn.queryProcessStatus(Opmn.java:328)
at oracle.as.management.mbeans.opmn.Opmn.getStatus(Opmn.java:85)
at oracle.as.management.mbeans.opmn.Opmn.getStatus(Opmn.java:75)
at sun.reflect.NativeMethodAccessorImpl.invoke0(Native Method)
at sun.reflect.NativeMethodAccessorImpl.invoke(NativeMethodAccessorImpl.java:39)
at sun.reflect.DelegatingMethodAccessorImpl.invoke(DelegatingMethodAccessorImpl.java:25)
at java.lang.reflect.Method.invoke(Method.java:597)
at com.sun.jmx.mbeanserver.StandardMBeanIntrospector.invokeM2(StandardMBeanIntrospector.java:93)
at com.sun.jmx.mbeanserver.StandardMBeanIntrospector.invokeM2(StandardMBeanIntrospector.java:27)
at com.sun.jmx.mbeanserver.MBeanIntrospector.invokeM(MBeanIntrospector.java:208)
at com.sun.jmx.mbeanserver.PerInterface.getAttribute(PerInterface.java:65)
at com.sun.jmx.mbeanserver.MBeanSupport.getAttribute(MBeanSupport.java:216)
at javax.management.StandardMBean.getAttribute(StandardMBean.java:358)
at oracle.as.jmx.framework.standardmbeans.spi.OracleStandardEmitterMBean.doGetAttribute(OracleStandardEmitterMBean.java:737)
at oracle.adf.mbean.share.AdfMBeanInterceptor.internalGetAttribute(AdfMBeanInterceptor.java:72)
at oracle.as.jmx.framework.generic.spi.interceptors.AbstractMBeanInterceptor.doGetAttribute(AbstractMBeanInterceptor.java:86)
at oracle.as.jmx.framework.generic.spi.security.AbstractMBeanSecurityInterceptor.internalGetAttribute(AbstractMBeanSecurityInterceptor.java:127)
at oracle.as.jmx.framework.generic.spi.interceptors.AbstractMBeanInterceptor.doGetAttribute(AbstractMBeanInterceptor.java:86)
at oracle.security.jps.ee.jmx.JpsJmxInterceptor$GetAttributeDelegator.delegate(JpsJmxInterceptor.java:843)
at oracle.security.jps.ee.jmx.JpsJmxInterceptor$7.run(JpsJmxInterceptor.java:747)
at java.security.AccessController.doPrivileged(Native Method)
at oracle.security.jps.util.JpsSubject.doAsPrivileged(JpsSubject.java:315)
at oracle.security.jps.ee.util.JpsPlatformUtil.runJaasMode(JpsPlatformUtil.java:442)
at oracle.security.jps.ee.jmx.JpsJmxInterceptor.jpsInternalInvoke(JpsJmxInterceptor.java:768)
at oracle.security.jps.ee.jmx.JpsJmxInterceptor.internalGetAttribute(JpsJmxInterceptor.java:230)
at oracle.as.jmx.framework.generic.spi.interceptors.AbstractMBeanInterceptor.doGetAttribute(AbstractMBeanInterceptor.java:86)
at oracle.as.jmx.framework.generic.spi.interceptors.ContextClassLoaderMBeanInterceptor.internalGetAttribute(ContextClassLoaderMBeanInterceptor.java:66)
at oracle.as.jmx.framework.generic.spi.interceptors.AbstractMBeanInterceptor.doGetAttribute(AbstractMBeanInterceptor.java:86)
at oracle.as.jmx.framework.generic.spi.interceptors.MBeanRestartInterceptor.internalGetAttribute(MBeanRestartInterceptor.java:67)
at oracle.as.jmx.framework.generic.spi.interceptors.AbstractMBeanInterceptor.doGetAttribute(AbstractMBeanInterceptor.java:86)
at oracle.as.jmx.framework.generic.spi.interceptors.LoggingMBeanInterceptor.internalGetAttribute(LoggingMBeanInterceptor.java:291)
at oracle.as.jmx.framework.generic.spi.interceptors.AbstractMBeanInterceptor.doGetAttribute(AbstractMBeanInterceptor.java:86)
at oracle.as.jmx.framework.standardmbeans.spi.OracleStandardEmitterMBean.getAttribute(OracleStandardEmitterMBean.java:716)
at com.sun.jmx.interceptor.DefaultMBeanServerInterceptor.getAttribute(DefaultMBeanServerInterceptor.java:666)
at com.sun.jmx.mbeanserver.JmxMBeanServer.getAttribute(JmxMBeanServer.java:638)
at weblogic.management.jmx.mbeanserver.WLSMBeanServerInterceptorBase$12.run(WLSMBeanServerInterceptorBase.java:326)
at java.security.AccessController.doPrivileged(Native Method)
at weblogic.management.jmx.mbeanserver.WLSMBeanServerInterceptorBase.getAttribute(WLSMBeanServerInterceptorBase.java:324)
at weblogic.management.mbeanservers.internal.JMXContextInterceptor.getAttribute(JMXContextInterceptor.java:157)
at weblogic.management.jmx.mbeanserver.WLSMBeanServerInterceptorBase$12.run(WLSMBeanServerInterceptorBase.java:326)
at java.security.AccessController.doPrivileged(Native Method)
at weblogic.management.jmx.mbeanserver.WLSMBeanServerInterceptorBase.getAttribute(WLSMBeanServerInterceptorBase.java:324)
at weblogic.management.mbeanservers.internal.SecurityInterceptor.getAttribute(SecurityInterceptor.java:299)
at weblogic.management.jmx.mbeanserver.WLSMBeanServer.getAttribute(WLSMBeanServer.java:279)
at weblogic.management.mbeanservers.domainruntime.internal.ManagedMBeanServerConnection.getAttribute(ManagedMBeanServerConnection.java:304)
at weblogic.management.mbeanservers.domainruntime.internal.FederatedMBeanServerInterceptor.getAttribute(FederatedMBeanServerInterceptor.java:308)
at weblogic.management.jmx.mbeanserver.WLSMBeanServerInterceptorBase$12.run(WLSMBeanServerInterceptorBase.java:326)
at java.security.AccessController.doPrivileged(Native Method)
at weblogic.management.jmx.mbeanserver.WLSMBeanServerInterceptorBase.getAttribute(WLSMBeanServerInterceptorBase.java:324)
at weblogic.management.mbeanservers.internal.JMXContextInterceptor.getAttribute(JMXContextInterceptor.java:157)
at weblogic.management.jmx.mbeanserver.WLSMBeanServerInterceptorBase$12.run(WLSMBeanServerInterceptorBase.java:326)
at java.security.AccessController.doPrivileged(Native Method)
at weblogic.management.jmx.mbeanserver.WLSMBeanServerInterceptorBase.getAttribute(WLSMBeanServerInterceptorBase.java:324)
at weblogic.management.jmx.mbeanserver.WLSMBeanServerInterceptorBase$12.run(WLSMBeanServerInterceptorBase.java:326)
at java.security.AccessController.doPrivileged(Native Method)
at weblogic.management.jmx.mbeanserver.WLSMBeanServerInterceptorBase.getAttribute(WLSMBeanServerInterceptorBase.java:324)
at weblogic.management.mbeanservers.internal.SecurityInterceptor.getAttribute(SecurityInterceptor.java:299)
at weblogic.management.jmx.mbeanserver.WLSMBeanServer.getAttribute(WLSMBeanServer.java:279)
at oracle.as.jmx.framework.generic.BaseMBeanServerInterceptor.getAttribute(BaseMBeanServerInterceptor.java:185)
at oracle.bi.management.adminservices.opmn.OpmnProcessController._isOpmnRunningWithProcesses(OpmnProcessController.java:636)
at oracle.bi.management.adminservices.opmn.OpmnProcessController.startThreadProcesses(OpmnProcessController.java:304)
at oracle.bi.management.adminservices.opmn.OpmnProcessController.startAll(OpmnProcessController.java:220)
at oracle.bi.management.adminservices.model.impl.ProcessManagerProxyImpl.startAll(ProcessManagerProxyImpl.java:144)
at oracle.bi.management.adminservices.mbeans.impl.BIInstanceMBeanImpl.startSystemComponents(BIInstanceMBeanImpl.java:409)
at oracle.bi.management.adminservices.mbeans.impl.BIInstanceMBeanImpl.localStart(BIInstanceMBeanImpl.java:307)
at oracle.bi.management.adminservices.mbeans.impl.BIInstanceMBeanImpl.start(BIInstanceMBeanImpl.java:246)
at oracle.bi.management.adminservices.mbeans.impl.BIInstanceMBeanImpl.start(BIInstanceMBeanImpl.java:284)
at sun.reflect.NativeMethodAccessorImpl.invoke0(Native Method)
at sun.reflect.NativeMethodAccessorImpl.invoke(NativeMethodAccessorImpl.java:39)
at sun.reflect.DelegatingMethodAccessorImpl.invoke(DelegatingMethodAccessorImpl.java:25)
at java.lang.reflect.Method.invoke(Method.java:597)
at oracle.as.jmx.framework.standardmbeans.spi.OracleStandardEmitterMBean.doInvoke(OracleStandardEmitterMBean.java:1012)
at oracle.adf.mbean.share.AdfMBeanInterceptor.internalInvoke(AdfMBeanInterceptor.java:104)
at oracle.as.jmx.framework.generic.spi.interceptors.AbstractMBeanInterceptor.doInvoke(AbstractMBeanInterceptor.java:252)
at oracle.as.jmx.framework.generic.spi.security.AbstractMBeanSecurityInterceptor.internalInvoke(AbstractMBeanSecurityInterceptor.java:190)
at oracle.as.jmx.framework.generic.spi.interceptors.AbstractMBeanInterceptor.doInvoke(AbstractMBeanInterceptor.java:252)
at oracle.security.jps.ee.jmx.JpsJmxInterceptor$2.run(JpsJmxInterceptor.java:358)
at java.security.AccessController.doPrivileged(Native Method)
at oracle.security.jps.util.JpsSubject.doAsPrivileged(JpsSubject.java:315)
at oracle.security.jps.ee.util.JpsPlatformUtil.runJaasMode(JpsPlatformUtil.java:442)
at oracle.security.jps.ee.jmx.JpsJmxInterceptor.internalInvoke(JpsJmxInterceptor.java:374)
at oracle.as.jmx.framework.generic.spi.interceptors.AbstractMBeanInterceptor.doInvoke(AbstractMBeanInterceptor.java:252)
at oracle.as.jmx.framework.generic.spi.interceptors.ContextClassLoaderMBeanInterceptor.internalInvoke(ContextClassLoaderMBeanInterceptor.java:103)
at oracle.as.jmx.framework.generic.spi.interceptors.AbstractMBeanInterceptor.doInvoke(AbstractMBeanInterceptor.java:252)
at oracle.as.jmx.framework.generic.spi.interceptors.MBeanRestartInterceptor.internalInvoke(MBeanRestartInterceptor.java:116)
at oracle.as.jmx.framework.generic.spi.interceptors.AbstractMBeanInterceptor.doInvoke(AbstractMBeanInterceptor.java:252)
at oracle.as.jmx.framework.generic.spi.interceptors.LoggingMBeanInterceptor.internalInvoke(LoggingMBeanInterceptor.java:524)
at oracle.as.jmx.framework.generic.spi.interceptors.AbstractMBeanInterceptor.doInvoke(AbstractMBeanInterceptor.java:252)
at oracle.as.jmx.framework.standardmbeans.spi.OracleStandardEmitterMBean.invoke(OracleStandardEmitterMBean.java:924)
at com.sun.jmx.interceptor.DefaultMBeanServerInterceptor.invoke(DefaultMBeanServerInterceptor.java:836)
at com.sun.jmx.mbeanserver.JmxMBeanServer.invoke(JmxMBeanServer.java:761)
at weblogic.management.mbeanservers.domainruntime.internal.FederatedMBeanServerInterceptor.invoke(FederatedMBeanServerInterceptor.java:349)
at weblogic.management.jmx.mbeanserver.WLSMBeanServerInterceptorBase$16.run(WLSMBeanServerInterceptorBase.java:449)
at java.security.AccessController.doPrivileged(Native Method)
at weblogic.management.jmx.mbeanserver.WLSMBeanServerInterceptorBase.invoke(WLSMBeanServerInterceptorBase.java:447)
at weblogic.management.mbeanservers.internal.JMXContextInterceptor.invoke(JMXContextInterceptor.java:263)
at weblogic.management.jmx.mbeanserver.WLSMBeanServerInterceptorBase$16.run(WLSMBeanServerInterceptorBase.java:449)
at java.security.AccessController.doPrivileged(Native Method)
at weblogic.management.jmx.mbeanserver.WLSMBeanServerInterceptorBase.invoke(WLSMBeanServerInterceptorBase.java:447)
at weblogic.management.mbeanservers.internal.SecurityMBeanMgmtOpsInterceptor.invoke(SecurityMBeanMgmtOpsInterceptor.java:65)
at weblogic.management.jmx.mbeanserver.WLSMBeanServerInterceptorBase$16.run(WLSMBeanServerInterceptorBase.java:449)
at java.security.AccessController.doPrivileged(Native Method)
at weblogic.management.jmx.mbeanserver.WLSMBeanServerInterceptorBase.invoke(WLSMBeanServerInterceptorBase.java:447)
at weblogic.management.mbeanservers.internal.SecurityInterceptor.invoke(SecurityInterceptor.java:444)
at weblogic.management.jmx.mbeanserver.WLSMBeanServer.invoke(WLSMBeanServer.java:323)
at weblogic.management.mbeanservers.internal.JMXConnectorSubjectForwarder$11$1.run(JMXConnectorSubjectForwarder.java:663)
at java.security.AccessController.doPrivileged(Native Method)
at weblogic.management.mbeanservers.internal.JMXConnectorSubjectForwarder$11.run(JMXConnectorSubjectForwarder.java:661)
at weblogic.security.acl.internal.AuthenticatedSubject.doAs(AuthenticatedSubject.java:363)
at weblogic.management.mbeanservers.internal.JMXConnectorSubjectForwarder.invoke(JMXConnectorSubjectForwarder.java:654)
at javax.management.remote.rmi.RMIConnectionImpl.doOperation(RMIConnectionImpl.java:1427)
at javax.management.remote.rmi.RMIConnectionImpl.access$200(RMIConnectionImpl.java:72)
at javax.management.remote.rmi.RMIConnectionImpl$PrivilegedOperation.run(RMIConnectionImpl.java:1265)
at java.security.AccessController.doPrivileged(Native Method)
at javax.management.remote.rmi.RMIConnectionImpl.doPrivilegedOperation(RMIConnectionImpl.java:1367)
at javax.management.remote.rmi.RMIConnectionImpl.invoke(RMIConnectionImpl.java:788)
at javax.management.remote.rmi.RMIConnectionImpl_WLSkel.invoke(Unknown Source)
at weblogic.rmi.internal.ServerRequest.sendReceive(ServerRequest.java:174)
at weblogic.rmi.internal.BasicRemoteRef.invoke(BasicRemoteRef.java:222)
at javax.management.remote.rmi.RMIConnectionImpl_1035_WLStub.invoke(Unknown Source)
at weblogic.management.remote.common.RMIConnectionWrapper$16.run(ClientProviderBase.java:919)
at weblogic.security.acl.internal.AuthenticatedSubject.doAs(AuthenticatedSubject.java:363)
at weblogic.security.service.SecurityManager.runAs(SecurityManager.java:146)
at weblogic.security.Security.runAs(Security.java:61)
at weblogic.management.remote.common.RMIConnectionWrapper.invoke(ClientProviderBase.java:917)
at javax.management.remote.rmi.RMIConnector$RemoteMBeanServerConnection.invoke(RMIConnector.java:993)
at oracle.sysman.emai.model.bi.impl.JmxUtil.invokeMethod(JmxUtil.java:184)
at oracle.sysman.emai.model.bi.impl.InstanceMBeanHelper.start(InstanceMBeanHelper.java:126)
at oracle.sysman.emai.model.bi.impl.InstanceModelAdaptor.start(InstanceModelAdaptor.java:319)
at oracle.sysman.emai.view.bi.SystemStartStopView.start(SystemStartStopView.java:46)
at oracle.sysman.emai.view.bi.AvailabilityView.startAllComponents(AvailabilityView.java:255)
at sun.reflect.NativeMethodAccessorImpl.invoke0(Native Method)
at sun.reflect.NativeMethodAccessorImpl.invoke(NativeMethodAccessorImpl.java:39)
at sun.reflect.DelegatingMethodAccessorImpl.invoke(DelegatingMethodAccessorImpl.java:25)
at java.lang.reflect.Method.invoke(Method.java:597)
at oracle.sysman.emas.sdk.progress.WorkWrapper.run(WorkWrapper.java:96)
at java.lang.Thread.run(Thread.java:662)
Caused by: java.net.ConnectException: Connection timed out: connect
at java.net.PlainSocketImpl.socketConnect(Native Method)
at java.net.PlainSocketImpl.doConnect(PlainSocketImpl.java:351)
at java.net.PlainSocketImpl.connectToAddress(PlainSocketImpl.java:213)
at java.net.PlainSocketImpl.connect(PlainSocketImpl.java:200)
at java.net.SocksSocketImpl.connect(SocksSocketImpl.java:366)
at java.net.Socket.connect(Socket.java:529)
at com.sun.net.ssl.internal.ssl.SSLSocketImpl.connect(SSLSocketImpl.java:564)
at com.sun.net.ssl.internal.ssl.SSLSocketImpl.<init>(SSLSocketImpl.java:365)
at com.sun.net.ssl.internal.ssl.SSLSocketFactoryImpl.createSocket(SSLSocketFactoryImpl.java:71)
at oracle.as.management.opmn.optic.OpmnSSL.getSecureSocket(OpmnSSL.java:48)
... 144 more
=================================================================================
Supplementary information regarding operation: ORACLE_INSTANCE:-:instance1;FAILED_CONTACTING_OPMN;Failed contacting OPMN, Please check if OPMN process is running. Cannot start or stop components of BI Instance.
=================================================================================Hi,
It look like port conflict issue.
Root Cause
The port, identified in the AdminServer-diagnostic log:
OPMN.queryProcessStatus failed with the following exception
[[ oracle.as.management.opmn.optic.OpticBadConnectException: Could not get secure socket for host slvgqa58.company.com and port 9501
at oracle.as.management.opmn.optic.OpmnSSL.getSecureSocket(OpmnSSL.java:52)
was fouled by a another process.
Solution
Clear the port, by using the netstat command (i.e. netstat -anp grep 9501) to identify the processes running on the specified port, and then kill those processes.Once the processes were terminated, all BI components, on both servers in the cluster, started successfully.
Thanks
Deva -
D20 Blue Screen loading Windows 7-64bit using Intel controller and Marvell enabled
Hi, Help,
Hardware:
D20, 4158, Four 500GB Seagate SATA drives configured as a RAID10 1TB virtual disk (partitioned into five logical drives).
Goal:
Recover or repair a degraded RAID array.
I want to be able to launch Windows 7-64bit using the Intel controller and have it access the virtual disk of the degraded RAID array attached to the Marvell controller. Subsequently, I want to use the Marvell MRU utility to repair/recover the situation.
Situation/Issue:
Things ran well for two years and two months until yesterday. Now, when booting I see:
1962: No operating system found. Press F1 to repeat boot sequence.
If I use the Windows 7 installation CD and load the Marvell driver, the attempt to recover the operating system reports that the MBR is corrupt and cannot be repaired.
If I boot with the Marvell controller disabled in the D20 BIOS, using a Windows 7 installation (with Marvell drivers) attached to the Intel controller, everything works except (of course) I cannot access the RAID drives.
If I reboot with the Marvell controller enabled, using the same Windows 7 installation via Intel controller, I see a "Starting Windows" announcement followed by a flash of the blue screen of death.
The BSOD message is unspecific, no error code, just...
"A problem has been detected and Windows has been shut down to prevent damage to your computer.
If this is the first time you've seen this Stop error screen,
restart your computer..."
Additional information:
If I access the Marvell BIOS (ctrl-M) and look at Devices, one of the four Seagate drives has status FREE instead of status ASSIGNED. If I run the Marvell BIOS verify disk utility diagnosic on that FREE status disk, I get a fault error after about 30 minutes of scanning. So, one Seagate disk is sour and somehow the MBR was corrupted at the same time.
History:
Two years ago, during the intial configuration, I could access the Marvell RAID disks from this Intel-controller-booted Windows 7 installation, but my fuzzy memory is that I had to change something in the D20 BIOS, such as the AHCI setting or similar.
Status:
Today, using the Intel controller to boot Windows 7 with the Marvell controller enabled is just BSOD. What am I missing or failing to do or set?
Thank you in advance for any help and ideas.
-John
Solved!
Go to Solution.Update:
I replaced the 500GB Seagate disk with a new 500GB Seagate. I ran the Marvell BIOS verify disk utility on the new disk drive and it passed with no errors. Following the steps given in the Marvell MRU online help, I rebuilt the virtual disk. Upon completion (which took a little more than an hour to complete), I rebooted. Before the Seagate disk went south yesterday, the Marvell virtual disk contained one primary partition (C, and four NTFS drives (D:, E:, F:, and Z. Now it contains three primary NTFS drives (C:, F:, and Z. An extended partition contains D: (an unformatted volume of size 199.30MB) and an unused space of 199.30GB.
Event log:
Looking at the event log, Windows reports that the disk in question raised a warning yesterday. Three messages share the same timestamp (all from mv64xx (a Marvell process):
"Physical disk 16 is plugged out."
"Virtual disk 0 is degraded."
"Physical disk 16 is plugged in."
Eight seconds later, UserPnp logs:
"Driver Management has concluded the process to add Service disk for Device Instance ID SCSI\DISK&VEN_SEAGATE&PROD_ST3500418AS&REV_CC38\5&248BBE23&0&000100 with the following status: 0"
One second later, UserPnp logs:
"Driver Management concluded the process to install driver FileRepository\disk.inf_amd64_neutral_10ce25bbc5a9cc43\disk.inf for Device Instance ID SCSI\DISK&VEN_SEAGATE&PROD_ST3500418AS&REV_CC38\5&248BBE23&0&000100 with the following status: 0x0."
Questions:
Is it possible that UserPnp corrupted the Marvell virtual disk after an intermittent physical disk unplugged/plugged-in event that happened when the Seagate hardware went failed. It looks to me like my D: and E: are toast despite RAID 10.
Any ideas? Is there anyway to recover the Marvell virtual disk configuration to the state prior to the hardware failure? If not, what good is RAID 10?
My apologies for the long posting, but I am an old software guy who does not understand the intricacies of RAID and disk management.
Thank you in advance for any leads toward a solution,
-John -
Windows 7 64bits Installing Internet Explorer 11 ERROR Neutral package installation failed
Hi,
The laptop is running Windows 7 64bits with Internet Explorer 10 and the Windows automatic updates is turned on. The problem happens when the Windows keeps installing the Internet Explorer 11 every time between shutdown process. So I decided to download
IE11 offline installation and try to install from it but the problem doesn't solve, the installation still does not complete. I have tried to delete all files in the Windows temp folder and IE temp folder already but the problem still exist.
Below is the details from IE11_main.log file
00:00.000:
====================================================================
00:00.000: Started: 2014/05/26 (Y/M/D) 11:00:44.473 (local)
00:00.000: Time Format in this log: MM:ss.mmm (minutes:seconds.milliseconds)
00:00.016: Command line: "C:\Users\TBG\Desktop\IE11-Windows6.1-x64-en-us.exe"
00:00.016: INFO: Setup installer for Internet Explorer: 11.0.9600.16428
00:00.016: INFO: Previous version of Internet Explorer: 10.0.9200.16866
00:00.016: INFO: Checking if iexplore.exe's current version is between 11.0.9600.0...
00:00.016: INFO: ...and 11.1.0.0...
00:00.016: INFO: Maximum version on which to run IEAK branding is: 11.1.0.0...
00:00.016: INFO: iexplore.exe version check success. Install can proceed.
00:00.016: INFO: Operating System: Windows Workstation: 6.1.7601 (Service Pack 1)
00:00.016: INFO: Trying to extract ID: SetupDownloadList.txt (0) as "SetupDownloadList.txt"
00:00.016: INFO: Trying to extract ID: HardwareBlockingList.xml (0) as "HardwareBlockingList.xml"
00:00.016: INFO: Trying to extract ID: 7006 (0) as "IE11-neutral.Extracted.cab"
00:00.702: INFO: Trying to extract ID: 5501 (1033) as "Spelling_en.msu"
00:00.702: INFO: Extracted Spelling dictionary for en to C:\Windows\TEMP\IE18CE4.tmp\Spelling_en.msu.
00:00.702: INFO: Trying to extract ID: 5502 (1033) as "Hyphenation_en.msu"
00:00.702: INFO: Extracted Hyphenation dictionary for en to
C:\Windows\TEMP\IE18CE4.tmp\Hyphenation_en.msu.
00:00.718: INFO: Trying to extract ID: 7128 (1033) as "IE11-support.cab"
00:01.607: INFO: PauseOrResumeAUThread: Successfully paused Automatic Updates.
00:02.714: INFO: Updated Download list, Hardware Blocking list, and no reboot policy files successfully downloaded
and extracted for use.
00:02.730: INFO: Launched program to check hardware: "C:\Windows\TEMP\IE18CE4.tmp\IE11-
SUPPORT\IEXPLORE.EXE" /CheckHardware "C:\Windows\TEMP\IE18CE4.tmp\IE11-support\HardwareBlockingList.xml"
00:02.870: INFO: Graphics Device Information: Intel(R) HD Graphics Family
00:02.870: INFO: Hardware support check succeeded. Installation will continue.
00:02.870: INFO: Windows 7 operating system detected.
00:02.886: INFO: Service pack major: 1
00:02.886: INFO: Service pack minor: 0
00:02.886: INFO: Service pack name: Service Pack 1
00:02.886: INFO: Version Check for (KB2834140) of C:\Windows\System32\d3d11.dll: 6.2.9200.16570 >=
6.2.9200.16570 (True)
00:02.886: INFO: Version Check for (KB2670838) of C:\Windows\System32\api-ms-win-downlevel-user32-l1-1-0.dll:
6.2.9200.16492 >= 6.2.9200.16426 (True)
00:02.886: INFO: Version Check for (KB2639308) of C:\Windows\System32\Ntoskrnl.exe: 6.1.7601.18409 >=
6.1.7601.17727 (True)
00:02.902: INFO: Version Check for (KB2533623) of C:\Windows\System32\api-ms-win-security-base-l1-1-0.dll:
6.1.7601.18229 >= 6.1.7601.17617 (True)
00:02.902: INFO: Version Check for (KB2731771) of C:\Windows\System32\conhost.exe: 6.1.7601.18229 >=
6.1.7601.17888 (True)
00:02.902: INFO: Checking for correct version of C:\Windows\Fonts\segoeui.ttf.
00:02.902: INFO: Version Check for (KB2786081) of C:\Windows\System32\taskhost.exe: 6.1.7601.18010 >=
6.1.7601.18010 (True)
00:02.902: INFO: Version Check for (KB2888049) of C:\Windows\System32\drivers\tcpip.sys: 6.1.7601.18254 >=
6.1.7601.18254 (True)
00:02.917: INFO: Version Check for (KB2882822) of C:\Windows\System32\tdh.dll: 6.1.7601.18247 >=
6.1.7601.18247 (True)
00:07.597: INFO: Waiting for 0 prerequisite downloads.
01:37.423: INFO: The neutral pack was successfully downloaded from the internet. Installation will continue using
the downloaded package.
01:37.423: INFO: Waiting for 0 language pack downloads.
01:37.423: INFO: Language pack downloads completed. (exit code = 0xffffffff (4294967295)).
01:37.438: INFO: No reboot logic message NrApiStart(0), lParam=0x03771068 returned 0x00000000.
01:38.000: INFO: No reboot logic message NrApiScan(1), lParam=0x00000001 returned 0x00000000.
01:38.000: INFO: No reboot logic message NrApiStartInstall(4), lParam=0x00000001 returned 0x00000014.
01:38.000: INFO: Installing with the downloaded package. C:\Windows\TEMP\IE18CE4.tmp\IE11-
neutral.Downloaded.cab
01:38.000: INFO: Launched package installation: C:\Windows\SysNative\dism.exe /online /add-package
/packagepath:C:\Windows\TEMP\IE18CE4.tmp\IE11-neutral.Downloaded.cab /quiet /norestart
02:20.619: INFO: Process exit code 0x80004005 (-2147467259) [Unspecified error ]
02:20.713: ERROR: Neutral package installation failed (exit code = 0x80004005 (2147500037)).
02:20.729: INFO: No reboot logic message NrApiInstallDone(7), lParam=0x00009c59 returned 0x00000000.
02:20.744: INFO: No reboot logic message NrApiStartFinish(11), lParam=0x00000000 returned 0x00000000.
02:20.775: INFO: No reboot logic message NrApiFinish(12), lParam=0x00000000 returned 0x00000016.
02:20.869: INFO: Waiting for Active Setup to complete.
02:20.963: INFO: PauseOrResumeAUThread: Successfully resumed Automatic Updates.
02:32.694: INFO: Setup exit code: 0x00009C59 (40025) - The neutral cab failed to install.
02:32.741: INFO: Scheduling upload to IE SQM server: http://sqm.microsoft.com/sqm/ie/sqmserver.dll
02:32.756: INFO: SQM Upload returned 403
02:36.453: INFO: Cleaning up temporary files in: C:\Windows\TEMP\IE18CE4.tmp
02:36.531: INFO: Unable to remove directory C:\Windows\TEMP\IE18CE4.tmp, marking for deletion on reboot.
02:36.531: INFO: Released Internet Explorer Installer Mutex
Taweesak ArchawamaitreekoolDISM.log would make this clearer. And using ProcMon I suspect would really make it snap out at you. <eg>
C.f. (credit for a recent discovery)
http://answers.microsoft.com/en-us/windows/forum/windows_7-windows_update/i-get-error-9c59-when-updating-internet-explorer/03d4473a-867b-44a5-9a37-913e9a5879cf?page=8&msgId=afe85da0-36e0-4160-860b-d2973e78c8b9
Unfortunately, since then others have quickly stuck a pin in this balloon, finding that it is just one more bump in the road, but at least working around this coding error should change your symptom.
Good luck
Robert Aldwinckle
Thank you very much.
I have tried to create a symbolic link as suggested on a forum but the problem still cannot be solved. The error message from IE11_main.log file is exactly the same as before.
For DISM.Log, here are the details from the started time of the installtion process
2014-05-29 16:53:55, Info DISM DISM.EXE: <----- Starting Dism.exe session ----->
2014-05-29 16:53:55, Info DISM DISM.EXE:
2014-05-29 16:53:55, Info DISM DISM.EXE: Host machine information: OS Version=6.1.7601, Running architecture=amd64, Number of processors=4
2014-05-29 16:53:55, Info DISM DISM.EXE: Executing command line: C:\Windows\SysNative\dism.exe /online /add-package /packagepath:C:\Windows\TEMP\IE1CA88.tmp\IE11-neutral.Downloaded.cab
/quiet /norestart
2014-05-29 16:53:55, Info DISM DISM Provider Store: PID=9144 Getting Provider FolderManager - CDISMProviderStore::GetProvider
2014-05-29 16:53:55, Info DISM DISM Provider Store: PID=9144 Provider has not previously been encountered. Attempting to initialize the provider.
- CDISMProviderStore::Internal_GetProvider
2014-05-29 16:53:55, Info DISM DISM Provider Store: PID=9144 Loading Provider from location C:\Windows\System32\Dism\FolderProvider.dll - CDISMProviderStore::Internal_GetProvider
2014-05-29 16:53:55, Info DISM DISM Provider Store: PID=9144 Connecting to the provider located at C:\Windows\System32\Dism\FolderProvider.dll.
- CDISMProviderStore::Internal_LoadProvider
2014-05-29 16:53:55, Info DISM DISM Provider Store: PID=9144 Getting Provider FolderManager - CDISMProviderStore::GetProvider
2014-05-29 16:53:55, Info DISM DISM Provider Store: PID=9144 Provider has previously been initialized. Returning the existing instance. -
CDISMProviderStore::Internal_GetProvider
2014-05-29 16:53:58, Info DISM DISM Manager: PID=9144 Successfully loaded the ImageSession at "C:\Users\TBG\AppData\Local\Temp\A444213B-3012-4ACB-9A8C-561F175FD583"
- CDISMManager::LoadImageSession
2014-05-29 16:53:58, Info DISM DISM Image Session: PID=8324 Instantiating the Provider Store. - CDISMImageSession::get_ProviderStore
2014-05-29 16:53:58, Info DISM DISM Provider Store: PID=8324 Initializing a provider store for the IMAGE session type. - CDISMProviderStore::Final_OnConnect
2014-05-29 16:53:58, Info DISM DISM Provider Store: PID=8324 Provider has not previously been encountered. Attempting to initialize the provider.
- CDISMProviderStore::Internal_GetProvider
2014-05-29 16:53:58, Info DISM DISM Provider Store: PID=8324 Loading Provider from location C:\Users\TBG\AppData\Local\Temp\A444213B-3012-4ACB-9A8C-561F175FD583\OSProvider.dll
- CDISMProviderStore::Internal_GetProvider
2014-05-29 16:53:58, Info DISM DISM Provider Store: PID=8324 Connecting to the provider located at C:\Users\TBG\AppData\Local\Temp\A444213B-3012-4ACB-9A8C-561F175FD583\OSProvider.dll.
- CDISMProviderStore::Internal_LoadProvider
2014-05-29 16:53:58, Info DISM DISM OS Provider: PID=8324 Defaulting SystemPath to C:\ - CDISMOSServiceManager::Final_OnConnect
2014-05-29 16:53:58, Info DISM DISM OS Provider: PID=8324 Defaulting Windows folder to C:\Windows - CDISMOSServiceManager::Final_OnConnect
2014-05-29 16:53:58, Info DISM DISM Provider Store: PID=8324 Attempting to initialize the logger from the Image Session. - CDISMProviderStore::Final_OnConnect
2014-05-29 16:53:58, Info DISM DISM Provider Store: PID=8324 Provider has not previously been encountered. Attempting to initialize the provider.
- CDISMProviderStore::Internal_GetProvider
2014-05-29 16:53:58, Info DISM DISM Provider Store: PID=8324 Loading Provider from location C:\Users\TBG\AppData\Local\Temp\A444213B-3012-4ACB-9A8C-561F175FD583\LogProvider.dll
- CDISMProviderStore::Internal_GetProvider
2014-05-29 16:53:58, Info DISM DISM Provider Store: PID=8324 Connecting to the provider located at C:\Users\TBG\AppData\Local\Temp\A444213B-3012-4ACB-9A8C-561F175FD583\LogProvider.dll.
- CDISMProviderStore::Internal_LoadProvider
2014-05-29 16:53:58, Info DISM DISM Provider Store: PID=8324 Getting Provider OSServices - CDISMProviderStore::GetProvider
2014-05-29 16:53:58, Info DISM DISM Provider Store: PID=8324 Provider has previously been initialized. Returning the existing instance. -
CDISMProviderStore::Internal_GetProvider
2014-05-29 16:53:58, Info DISM DISM Provider Store: PID=8324 Found and Initialized the DISM Logger. - CDISMProviderStore::Internal_InitializeLogger
2014-05-29 16:53:58, Info DISM DISM Provider Store: PID=8324 Provider has not previously been encountered. Attempting to initialize the provider.
- CDISMProviderStore::Internal_GetProvider
2014-05-29 16:53:58, Info DISM DISM Provider Store: PID=8324 Loading Provider from location C:\Users\TBG\AppData\Local\Temp\A444213B-3012-4ACB-9A8C-561F175FD583\PEProvider.dll
- CDISMProviderStore::Internal_GetProvider
2014-05-29 16:53:58, Warning DISM DISM Provider Store: PID=8324 Failed to Load the provider: C:\Users\TBG\AppData\Local\Temp\A444213B-3012-4ACB-9A8C-561F175FD583\PEProvider.dll.
- CDISMProviderStore::Internal_GetProvider(hr:0x8007007e)
2014-05-29 16:53:58, Info DISM DISM Provider Store: PID=8324 Failed to get and initialize the PE Provider. Continuing by assuming that it
is not a WinPE image. - CDISMProviderStore::Final_OnConnect
2014-05-29 16:53:58, Info DISM DISM Provider Store: PID=8324 Finished initializing the Provider Map. - CDISMProviderStore::Final_OnConnect
2014-05-29 16:53:58, Info DISM DISM Provider Store: PID=8324 Getting Provider DISMLogger - CDISMProviderStore::GetProvider
2014-05-29 16:53:58, Info DISM DISM Provider Store: PID=8324 Provider has previously been initialized. Returning the existing instance. -
CDISMProviderStore::Internal_GetProvider
2014-05-29 16:53:58, Info DISM DISM Manager: PID=9144 Image session successfully loaded from the temporary location: C:\Users\TBG\AppData\Local\Temp\A444213B-3012-4ACB-9A8C-561F175FD583
- CDISMManager::CreateImageSession
2014-05-29 16:53:58, Info DISM DISM Provider Store: PID=8324 Getting Provider OSServices - CDISMProviderStore::GetProvider
2014-05-29 16:53:58, Info DISM DISM Provider Store: PID=8324 Provider has previously been initialized. Returning the existing instance. -
CDISMProviderStore::Internal_GetProvider
2014-05-29 16:53:58, Info CSI 00000001 Shim considered [l:256{128}]"\??\C:\Windows\Servicing\amd64_microsoft-windows-servicingstack_31bf3856ad364e35_6.1.7601.17592_none_672ce6c3de2cb17f\pkgmgr.exe"
: got STATUS_OBJECT_PATH_NOT_FOUND
2014-05-29 16:53:58, Info CSI 00000002 Shim considered [l:250{125}]"\??\C:\Windows\WinSxS\amd64_microsoft-windows-servicingstack_31bf3856ad364e35_6.1.7601.17592_none_672ce6c3de2cb17f\pkgmgr.exe"
: got STATUS_SUCCESS
2014-05-29 16:53:58, Info DISM DISM.EXE: Target image information: OS Version=6.1.7601.17592, Image architecture=amd64
2014-05-29 16:53:58, Info DISM DISM Provider Store: PID=8324 Getting the collection of providers from an image provider store type. - CDISMProviderStore::GetProviderCollection
2014-05-29 16:53:58, Info DISM DISM Provider Store: PID=8324 Provider has not previously been encountered. Attempting to initialize the provider.
- CDISMProviderStore::Internal_GetProvider
2014-05-29 16:53:58, Info DISM DISM Provider Store: PID=8324 Loading Provider from location C:\Users\TBG\AppData\Local\Temp\A444213B-3012-4ACB-9A8C-561F175FD583\CbsProvider.dll
- CDISMProviderStore::Internal_GetProvider
2014-05-29 16:53:58, Info DISM DISM Provider Store: PID=8324 Connecting to the provider located at C:\Users\TBG\AppData\Local\Temp\A444213B-3012-4ACB-9A8C-561F175FD583\CbsProvider.dll.
- CDISMProviderStore::Internal_LoadProvider
2014-05-29 16:53:58, Info DISM DISM Provider Store: PID=8324 Encountered a servicing provider, performing additional servicing initializations.
- CDISMProviderStore::Internal_LoadProvider
2014-05-29 16:53:58, Info CSI 00000001 Shim considered [l:256{128}]"\??\C:\Windows\Servicing\amd64_microsoft-windows-servicingstack_31bf3856ad364e35_6.1.7601.17592_none_672ce6c3de2cb17f\pkgmgr.exe"
: got STATUS_OBJECT_PATH_NOT_FOUND
2014-05-29 16:53:58, Info CSI 00000002 Shim considered [l:250{125}]"\??\C:\Windows\WinSxS\amd64_microsoft-windows-servicingstack_31bf3856ad364e35_6.1.7601.17592_none_672ce6c3de2cb17f\pkgmgr.exe"
: got STATUS_SUCCESS
2014-05-29 16:53:59, Info DISM DISM Package Manager: PID=8324 Finished initializing the CbsConUI Handler. - CCbsConUIHandler::Initialize
2014-05-29 16:53:59, Info CSI 00000001 Shim considered [l:256{128}]"\??\C:\Windows\Servicing\amd64_microsoft-windows-servicingstack_31bf3856ad364e35_6.1.7601.17592_none_672ce6c3de2cb17f\pkgmgr.exe"
: got STATUS_OBJECT_PATH_NOT_FOUND
2014-05-29 16:53:59, Info CSI 00000002 Shim considered [l:250{125}]"\??\C:\Windows\WinSxS\amd64_microsoft-windows-servicingstack_31bf3856ad364e35_6.1.7601.17592_none_672ce6c3de2cb17f\pkgmgr.exe"
: got STATUS_SUCCESS
2014-05-29 16:53:59, Info DISM DISM Package Manager: PID=8324 CBS is being initialized for online use. More information about CBS actions can be
located at: %windir%\logs\cbs\cbs.log - CDISMPackageManager::Initialize
2014-05-29 16:53:59, Info DISM DISM Package Manager: PID=8324 Loaded servicing stack for online use only. - CDISMPackageManager::RefreshInstanceAndLock
2014-05-29 16:53:59, Info DISM DISM Provider Store: PID=8324 Provider has not previously been encountered. Attempting to initialize the provider.
- CDISMProviderStore::Internal_GetProvider
2014-05-29 16:53:59, Info DISM DISM Provider Store: PID=8324 Loading Provider from location C:\Users\TBG\AppData\Local\Temp\A444213B-3012-4ACB-9A8C-561F175FD583\MsiProvider.dll
- CDISMProviderStore::Internal_GetProvider
2014-05-29 16:53:59, Info DISM DISM Provider Store: PID=8324 Connecting to the provider located at C:\Users\TBG\AppData\Local\Temp\A444213B-3012-4ACB-9A8C-561F175FD583\MsiProvider.dll.
- CDISMProviderStore::Internal_LoadProvider
2014-05-29 16:53:59, Info DISM DISM Provider Store: PID=8324 Encountered a servicing provider, performing additional servicing initializations.
- CDISMProviderStore::Internal_LoadProvider
2014-05-29 16:53:59, Info DISM DISM Provider Store: PID=8324 Provider has not previously been encountered. Attempting to initialize the provider.
- CDISMProviderStore::Internal_GetProvider
2014-05-29 16:53:59, Info DISM DISM Provider Store: PID=8324 Loading Provider from location C:\Users\TBG\AppData\Local\Temp\A444213B-3012-4ACB-9A8C-561F175FD583\IntlProvider.dll
- CDISMProviderStore::Internal_GetProvider
2014-05-29 16:53:59, Info DISM DISM Provider Store: PID=8324 Connecting to the provider located at C:\Users\TBG\AppData\Local\Temp\A444213B-3012-4ACB-9A8C-561F175FD583\IntlProvider.dll.
- CDISMProviderStore::Internal_LoadProvider
2014-05-29 16:53:59, Info DISM DISM Provider Store: PID=8324 Encountered a servicing provider, performing additional servicing initializations.
- CDISMProviderStore::Internal_LoadProvider
2014-05-29 16:53:59, Info DISM DISM Provider Store: PID=8324 Provider has not previously been encountered. Attempting to initialize the provider.
- CDISMProviderStore::Internal_GetProvider
2014-05-29 16:53:59, Info DISM DISM Provider Store: PID=8324 Loading Provider from location C:\Users\TBG\AppData\Local\Temp\A444213B-3012-4ACB-9A8C-561F175FD583\DmiProvider.dll
- CDISMProviderStore::Internal_GetProvider
2014-05-29 16:53:59, Info DISM DISM Provider Store: PID=8324 Connecting to the provider located at C:\Users\TBG\AppData\Local\Temp\A444213B-3012-4ACB-9A8C-561F175FD583\DmiProvider.dll.
- CDISMProviderStore::Internal_LoadProvider
2014-05-29 16:53:59, Info DISM DISM Provider Store: PID=8324 Encountered a servicing provider, performing additional servicing initializations.
- CDISMProviderStore::Internal_LoadProvider
2014-05-29 16:53:59, Info CSI 00000001 Shim considered [l:256{128}]"\??\C:\Windows\Servicing\amd64_microsoft-windows-servicingstack_31bf3856ad364e35_6.1.7601.17592_none_672ce6c3de2cb17f\pkgmgr.exe"
: got STATUS_OBJECT_PATH_NOT_FOUND
2014-05-29 16:53:59, Info CSI 00000002 Shim considered [l:250{125}]"\??\C:\Windows\WinSxS\amd64_microsoft-windows-servicingstack_31bf3856ad364e35_6.1.7601.17592_none_672ce6c3de2cb17f\pkgmgr.exe"
: got STATUS_SUCCESS
2014-05-29 16:53:59, Info DISM DISM OS Provider: PID=8324 Successfully loaded the hive. - CDISMOSServiceManager::DetermineBootDrive
2014-05-29 16:53:59, Info DISM DISM Driver Manager: PID=8324 Further logs for driver related operations can be found in the target operating system
at %WINDIR%\inf\setupapi.offline.log - CDriverManager::Initialize
2014-05-29 16:53:59, Info DISM DISM Provider Store: PID=8324 Provider has not previously been encountered. Attempting to initialize the provider.
- CDISMProviderStore::Internal_GetProvider
2014-05-29 16:53:59, Info DISM DISM Provider Store: PID=8324 Loading Provider from location C:\Users\TBG\AppData\Local\Temp\A444213B-3012-4ACB-9A8C-561F175FD583\UnattendProvider.dll
- CDISMProviderStore::Internal_GetProvider
2014-05-29 16:53:59, Info DISM DISM Provider Store: PID=8324 Connecting to the provider located at C:\Users\TBG\AppData\Local\Temp\A444213B-3012-4ACB-9A8C-561F175FD583\UnattendProvider.dll.
- CDISMProviderStore::Internal_LoadProvider
2014-05-29 16:53:59, Info DISM DISM Provider Store: PID=8324 Encountered a servicing provider, performing additional servicing initializations.
- CDISMProviderStore::Internal_LoadProvider
2014-05-29 16:53:59, Info DISM DISM Provider Store: PID=8324 Provider has not previously been encountered. Attempting to initialize the provider.
- CDISMProviderStore::Internal_GetProvider
2014-05-29 16:53:59, Info DISM DISM Provider Store: PID=8324 Loading Provider from location C:\Users\TBG\AppData\Local\Temp\A444213B-3012-4ACB-9A8C-561F175FD583\SmiProvider.dll
- CDISMProviderStore::Internal_GetProvider
2014-05-29 16:53:59, Info DISM DISM Provider Store: PID=8324 Connecting to the provider located at C:\Users\TBG\AppData\Local\Temp\A444213B-3012-4ACB-9A8C-561F175FD583\SmiProvider.dll.
- CDISMProviderStore::Internal_LoadProvider
2014-05-29 16:53:59, Info DISM DISM Provider Store: PID=8324 Encountered a servicing provider, performing additional servicing initializations.
- CDISMProviderStore::Internal_LoadProvider
2014-05-29 16:53:59, Info DISM DISM Provider Store: PID=8324 Provider has not previously been encountered. Attempting to initialize the provider.
- CDISMProviderStore::Internal_GetProvider
2014-05-29 16:53:59, Info DISM DISM Provider Store: PID=8324 Loading Provider from location C:\Users\TBG\AppData\Local\Temp\A444213B-3012-4ACB-9A8C-561F175FD583\TransmogProvider.dll
- CDISMProviderStore::Internal_GetProvider
2014-05-29 16:53:59, Info DISM DISM Provider Store: PID=8324 Connecting to the provider located at C:\Users\TBG\AppData\Local\Temp\A444213B-3012-4ACB-9A8C-561F175FD583\TransmogProvider.dll.
- CDISMProviderStore::Internal_LoadProvider
2014-05-29 16:53:59, Info DISM DISM Provider Store: PID=8324 Encountered a servicing provider, performing additional servicing initializations.
- CDISMProviderStore::Internal_LoadProvider
2014-05-29 16:53:59, Info DISM DISM Provider Store: PID=8324 Getting Provider DISM Package Manager - CDISMProviderStore::GetProvider
2014-05-29 16:53:59, Info DISM DISM Provider Store: PID=8324 Provider has previously been initialized. Returning the existing instance. -
CDISMProviderStore::Internal_GetProvider
2014-05-29 16:53:59, Info DISM DISM Provider Store: PID=8324 Getting Provider DISM Unattend Manager - CDISMProviderStore::GetProvider
2014-05-29 16:53:59, Info DISM DISM Provider Store: PID=8324 Provider has previously been initialized. Returning the existing instance. -
CDISMProviderStore::Internal_GetProvider
2014-05-29 16:53:59, Info DISM DISM.EXE: Got the collection of providers. Now enumerating them to build the command table.
2014-05-29 16:53:59, Info DISM DISM.EXE: Attempting to add the commands from provider: DISM Package Manager
2014-05-29 16:53:59, Info DISM DISM.EXE: Succesfully registered commands for the provider: DISM Package Manager.
2014-05-29 16:53:59, Info DISM DISM.EXE: Attempting to add the commands from provider: OSServices
2014-05-29 16:53:59, Info DISM DISM.EXE: Attempting to add the commands from provider: MsiManager
2014-05-29 16:53:59, Info DISM DISM.EXE: Succesfully registered commands for the provider: MsiManager.
2014-05-29 16:53:59, Info DISM DISM.EXE: Attempting to add the commands from provider: IntlManager
2014-05-29 16:53:59, Info DISM DISM.EXE: Succesfully registered commands for the provider: IntlManager.
2014-05-29 16:53:59, Info DISM DISM.EXE: Attempting to add the commands from provider: DriverManager
2014-05-29 16:53:59, Info DISM DISM.EXE: Succesfully registered commands for the provider: DriverManager.
2014-05-29 16:53:59, Info DISM DISM.EXE: Attempting to add the commands from provider: DISM Unattend Manager
2014-05-29 16:53:59, Info DISM DISM.EXE: Succesfully registered commands for the provider: DISM Unattend Manager.
2014-05-29 16:53:59, Info DISM DISM.EXE: Attempting to add the commands from provider: DISM Log Provider
2014-05-29 16:53:59, Info DISM DISM.EXE: Attempting to add the commands from provider: SmiManager
2014-05-29 16:53:59, Info DISM DISM.EXE: Attempting to add the commands from provider: Edition Manager
2014-05-29 16:53:59, Info DISM DISM Transmog Provider: PID=8324 Current image session is [ONLINE] - CTransmogManager::GetMode
2014-05-29 16:53:59, Info DISM DISM.EXE: Succesfully registered commands for the provider: Edition Manager.
2014-05-29 16:53:59, Info DISM DISM Provider Store: PID=8324 Getting Provider DISM Package Manager - CDISMProviderStore::GetProvider
2014-05-29 16:53:59, Info DISM DISM Provider Store: PID=8324 Provider has previously been initialized. Returning the existing instance. -
CDISMProviderStore::Internal_GetProvider
2014-05-29 16:53:59, Info DISM DISM Package Manager: PID=8324 Processing the top level command token(add-package). - CPackageManagerCLIHandler::Private_ValidateCmdLine
2014-05-29 16:53:59, Info DISM DISM Package Manager: PID=8324 Attempting to route to appropriate command handler. - CPackageManagerCLIHandler::ExecuteCmdLine
2014-05-29 16:53:59, Info DISM DISM Package Manager: PID=8324 Routing the command... - CPackageManagerCLIHandler::ExecuteCmdLine
2014-05-29 16:53:59, Info DISM DISM Package Manager: PID=8324 Encountered the option "packagepath" with value "C:\Windows\TEMP\IE1CA88.tmp\IE11-neutral.Downloaded.cab"
- CPackageManagerCLIHandler::Private_GetPackagesFromCommandLine
2014-05-29 16:53:59, Info DISM DISM Package Manager: PID=8324 Package Microsoft-Windows-InternetExplorer-Package-TopLevel~31bf3856ad364e35~amd64~~11.2.9600.16428
with CBS state 4(CbsInstallStateStaged) being mapped to dism state 3(DISM_INSTALL_STATE_STAGED) - CDISMPackage::LogInstallStateMapping
2014-05-29 16:53:59, Info DISM DISM Package Manager: PID=8324 Initiating Changes on Package with values: 4, 7 - CDISMPackage::Internal_ChangePackageState
2014-05-29 16:54:00, Info DISM PID=4640 Scratch directory set to 'C:\Users\TBG\AppData\Local\Temp\'. - CDISMManager::put_ScratchDir
2014-05-29 16:54:00, Info DISM PID=4640 Successfully loaded the ImageSession at "C:\Windows\System32\Dism" - CDISMManager::LoadImageSession
2014-05-29 16:54:00, Info DISM DISM Provider Store: PID=4640 Found and Initialized the DISM Logger. - CDISMProviderStore::Internal_InitializeLogger
2014-05-29 16:54:00, Info DISM DISM Provider Store: PID=4640 Failed to get and initialize the PE Provider. Continuing by assuming that it
is not a WinPE image. - CDISMProviderStore::Final_OnConnect
2014-05-29 16:54:00, Info DISM DISM Provider Store: PID=4640 Finished initializing the Provider Map. - CDISMProviderStore::Final_OnConnect
2014-05-29 16:54:00, Info DISM DISM Provider Store: PID=4640 Getting Provider DISMLogger - CDISMProviderStore::GetProvider
2014-05-29 16:54:00, Info DISM DISM Provider Store: PID=4640 Provider has previously been initialized. Returning the existing instance. -
CDISMProviderStore::Internal_GetProvider
2014-05-29 16:54:00, Info DISM DISM Provider Store: PID=4640 Getting Provider DISMLogger - CDISMProviderStore::GetProvider
2014-05-29 16:54:00, Info DISM DISM Provider Store: PID=4640 Provider has previously been initialized. Returning the existing instance. -
CDISMProviderStore::Internal_GetProvider
2014-05-29 16:54:00, Info DISM DISM Manager: PID=4640 Successfully created the local image session and provider store. - CDISMManager::CreateLocalImageSession
2014-05-29 16:54:00, Info DISM DISM Provider Store: PID=4640 Getting Provider DISMLogger - CDISMProviderStore::GetProvider
2014-05-29 16:54:00, Info DISM DISM Provider Store: PID=4640 Provider has previously been initialized. Returning the existing instance. -
CDISMProviderStore::Internal_GetProvider
2014-05-29 16:54:00, Info DISM DISM.EXE:
2014-05-29 16:54:00, Info DISM DISM.EXE: <----- Starting Dism.exe session ----->
2014-05-29 16:54:00, Info DISM DISM.EXE:
2014-05-29 16:54:00, Info DISM DISM.EXE: Host machine information: OS Version=6.1.7601, Running architecture=amd64, Number of processors=4
2014-05-29 16:54:00, Info DISM DISM.EXE: Executing command line: c:\windows\sysnative\dism.exe
2014-05-29 16:54:00, Info DISM DISM Provider Store: PID=4640 Getting the collection of providers from a local provider store type. - CDISMProviderStore::GetProviderCollection
2014-05-29 16:54:00, Info DISM DISM Provider Store: PID=4640 Provider has not previously been encountered. Attempting to initialize the provider.
- CDISMProviderStore::Internal_GetProvider
2014-05-29 16:54:00, Info DISM DISM Provider Store: PID=4640 Loading Provider from location C:\Windows\System32\Dism\WimProvider.dll - CDISMProviderStore::Internal_GetProvider
2014-05-29 16:54:00, Info DISM DISM Provider Store: PID=4640 Connecting to the provider located at C:\Windows\System32\Dism\WimProvider.dll. -
CDISMProviderStore::Internal_LoadProvider
2014-05-29 16:54:00, Info DISM DISM Provider Store: PID=4640 Provider has not previously been encountered. Attempting to initialize the provider.
- CDISMProviderStore::Internal_GetProvider
2014-05-29 16:54:00, Info DISM DISM Provider Store: PID=4640 Loading Provider from location C:\Windows\System32\Dism\FolderProvider.dll - CDISMProviderStore::Internal_GetProvider
2014-05-29 16:54:00, Info DISM DISM Provider Store: PID=4640 Connecting to the provider located at C:\Windows\System32\Dism\FolderProvider.dll.
- CDISMProviderStore::Internal_LoadProvider
2014-05-29 16:54:00, Info DISM DISM Provider Store: PID=4640 Provider has not previously been encountered. Attempting to initialize the provider.
- CDISMProviderStore::Internal_GetProvider
2014-05-29 16:54:00, Info DISM DISM Provider Store: PID=4640 Loading Provider from location C:\Windows\System32\Dism\CompatProvider.dll - CDISMProviderStore::Internal_GetProvider
2014-05-29 16:54:00, Info DISM DISM Provider Store: PID=4640 Connecting to the provider located at C:\Windows\System32\Dism\CompatProvider.dll.
- CDISMProviderStore::Internal_LoadProvider
2014-05-29 16:54:00, Info DISM DISM.EXE: Got the collection of providers. Now enumerating them to build the command table.
2014-05-29 16:54:00, Info DISM DISM.EXE: Attempting to add the commands from provider: WimManager
2014-05-29 16:54:00, Info DISM DISM.EXE: Getting the help information collection for the provider: WimManager.
2014-05-29 16:54:00, Info DISM DISM.EXE: Registering information from the help collection from provider: WimManager.
2014-05-29 16:54:00, Info DISM DISM.EXE: Succesfully registered the Help Item with topic(wimcommands) and category(localtoplevelhelp) for the provider(WimManager).
2014-05-29 16:54:00, Info DISM DISM.EXE: Succesfully registered the Help Item with topic(cleanup-wim) and category(wimcommands) for the provider(WimManager).
2014-05-29 16:54:00, Info DISM DISM.EXE: Succesfully registered the Help Item with topic(remount-wim) and category(wimcommands) for the provider(WimManager).
2014-05-29 16:54:00, Info DISM DISM.EXE: Succesfully registered the Help Item with topic(mount-wim) and category(wimcommands) for the provider(WimManager).
2014-05-29 16:54:00, Info DISM DISM.EXE: Succesfully registered the Help Item with topic(unmount-wim) and category(wimcommands) for the provider(WimManager).
2014-05-29 16:54:00, Info DISM DISM.EXE: Succesfully registered the Help Item with topic(commit-wim) and category(wimcommands) for the provider(WimManager).
2014-05-29 16:54:00, Info DISM DISM.EXE: Succesfully registered the Help Item with topic(get-wiminfo) and category(wimcommands) for the provider(WimManager).
2014-05-29 16:54:00, Info DISM DISM.EXE: Succesfully registered the Help Item with topic(get-mountedwiminfo) and category(wimcommands) for the
provider(WimManager).
2014-05-29 16:54:00, Info DISM DISM.EXE: Attempting to add the commands from provider: FolderManager
2014-05-29 16:54:00, Info DISM DISM.EXE: Attempting to add the commands from provider: DISM Log Provider
2014-05-29 16:54:00, Info DISM DISM.EXE: Attempting to add the commands from provider: Compatibility Manager
2014-05-29 16:54:00, Info DISM DISM.EXE: Getting the help information collection for the provider: Compatibility Manager.
2014-05-29 16:54:00, Info DISM DISM.EXE: Image session has been closed. Reboot required=no.
2014-05-29 16:54:00, Info DISM DISM.EXE:
2014-05-29 16:54:00, Info DISM DISM.EXE: <----- Ending Dism.exe session ----->
Taweesak Archawamaitreekool -
Hi I'm having problems installing and starting itunes program on Windows 7 64bit. After install the following error message is flagged - The file "i Tunes Library.itl" cannot be read because it was created by a newer version of iTunes. Would really appreciate any pointers!
Never mind sorted it out lol. Somebody did a system restore of a week or so. I had done the update during that time and it was lost. Just redownloaded itunes from the internet and its working fine now.
-
Help setting up my new IPod Touch on iTunes on windows 7 64bit
Hello there,
I need help setting up my new IPod Touch to my Itunes 10 application on a PC running windows 7 64bit. I have watched the tutorial on how to do it but what the tutorial says it is supposed to do is not what is happenning for me:
1. In the tutorial it tells you to connect your ipod to your computer, then, (if it is for the first time) when the ipod appears and is selected, a window will come up allowing you to name your ipod, and begin selecting the options you wish to use.
I did as instructed but quickly came against some technical issues.
My issues:
1-1: When I selected the new iPod Touch for the dirst time I got an error message.
A) This was quickly fixed once I calld up apple support on the phone (turns out an IE browser setting was blocking it.)
1-2: With that fixed I selected my iPod Touch again but instead of the window indicated by the tutorial, I instead got an iPod registration form window.
1-3: I filled out the form and pressed the submit button (thinking everything was fine), then a new window came up that looks like this:
Free Find My iPhone
Free Find My iPad
Free Find My iPod touch
Set up Find My iPhone for free so you can locate your device if you lose it, remotely lock the screen, or wipe its data. You can also find your iPad or iPod touch.Set up Find My iPad for free so you can locate your device if you lose it, remotely lock the screen, or wipe its data. You can also find your iPhone or iPod touch.Set up Find My iPod touch for free so you can locate your device if you lose it, remotely lock the screen, or wipe its data. You can also find your iPhone or iPad. _Learn More_
_Set up Find My iPhone_
_Not Now_ _Set up Find My iPad_
_Set up Find My iPod touch_
Find My iPhone (or iPad or iPod touch) enables you to locate your iPad with Wi-Fi or iPod touch only when it is on and connected to a registered Wi-Fi network. Find My iPhone is not available in all countries. "
The first three lines and the first paragraph are indented as if there should be some type of graphic there, but it is missing. The underlined words indicate that they are supposed to be links, but they don't go anywhere, they are broken!
Now wheenever I connect my iPod Touch and select it the above window comes up and nomatter what I try it will not move or change.
Please help!
MSRankinTry setting up the device in a new user account. or visit register.apple.com and verify your device is registered
Maybe you are looking for
-
I know there is a lot of info on this question, but it just doesn't make sense to me. I've created and published a website using iweb. I purchased a domain name through yahoo and set it to link to the iweb page. I used iweb because I don't know a lot
-
Does the iMac have an AUDIO IN besides from the built-in mic?
Does the iMac have an AUDIO IN aside from the built-in mic? Also, are any special cables needed? Thanks, John
-
Can i use my airport to boos a signal received from my broadband wifi transmitter?
Can I use my airport extreme device to boost my broadband signal as a secondary wifi transmitter? Any ideas?
-
Auto-Start of managed server (WL 8.1)
We have WebLogic 8.1 on Windows 2003. This machine has one domain with one managed server and one node manager. What do we need to do, if we would like to have the managed server automatically started,
-
Register multiple hosts in one rmiregistry
Why can i only register RemoteObjects on the same machine as the rmiregistry? I thought rmiregistry would translate a servicename into address and port of the service and after that the client connects to that machine, so i dont see any security prob