HP 932c duplexer on Windows 7

old printer died. obtained a replacement. can't get duplexer to work. assistance appreciated.

Hi,
Based on the following specs, it does not have a duplexer:
http://h20000.www2.hp.com/bizsupport/TechSupport/Document.jsp?%20lang=en&cc=us&objectID=bud07406
Hope this helps.
BH
**Click the KUDOS thumb up on the left to say 'Thanks'**
Make it easier for other people to find solutions by marking a Reply 'Accept as Solution' if it solves your problem.

Similar Messages

HP1320 won't duplex with Windows 7

I've downloaded HP Windows 7 64 bit drivers from your website and all duplexing options in preferences are checked and still printer won't duplex using Windows 7 Professional. It worked fine under Windows XP. What's the fix?

Let's set a static IP address for the printer so that the software is not chasing a changing IP:
- Print a Network Config Page from the front of the printer. Note the printer's IP address.
- Type that IP address into a browser to reveal the printer's internal settings.
- Choose the Networking tab, then Wireless along the left side, then the IPv4 tab.
- On this screen you want to set a Manual IP. You need to set an IP address outside the range that the router automatically sets (called the DHCP range). If you know what that is, set an IP outside that range but no higher than 254 (the last number in the address). If you do not know this, enter the current IP address.
- Use 255.255.255.0 for the subnet (unless you know it is different, if so, use that)
- Leave the gateway and DNS blank. Click 'Apply'
Now, shut down the router and printer, start the router, wait, then start the printer.
After this you may need to redo 'Add a Printer' using the new IP address.
Say thanks by clicking "Kudos" "thumbs up" in the post that helped you.
I am employed by HP

Printing duplex with HP Officejet Pro 8600 causes windows 7 OS to shut down/restart

Why when printing duplex with my HP Officejet Pro 8600 printer it causes windows 7( 64-bit) to shut down/restart. Windows message is "Windows has recovered from an unexpected shutdown. I've ran HP Hardward Diag. Utility and Print and Scan Doctor which indicated everything is working properly with the printer. Ocassionaly I can print duplex without windows shutting down and restarting, but most of the time it creates issue with Windows causing it to stop and restart. Single sided printing seems to be fine. I've already oncehad windows to "Startup Repair" in which ccase I selected restore to a previous working point. Everything worked for awhile then a duplex printing session starting causing windows to shut down again. THanks for your assistance.

Yes, the updated USB 3.0 driver corrects the issue and should be installed.
Bob Headrick, HP Expert
I am not an employee of HP, I am a volunteer posting here on my own time.
If your problem is solved please click the "Accept as Solution" button ------------V
If my answer was helpful please click the "Thumbs Up" to say "Thank You"--V

Sb 16 pci full duplex HELP!

ok im running windows 98 with a soundblaster 6 pci and i cannot get full duplex why?i used to be running windows xp and i got full duplex fine could play 2 devices at once but with windows 98 i cant and i was wondering why i cant i play counterstrike and use ventrilo to chat at same time well when i start up the game it cuts ventrilo out so i cant talk and when im in the game i cant talk as well it cuts the sound off to ventrilo so that tthe game lets me hear but i cant hear the chat program so i get no full duplex on windows 98 please help how do i fix this

On those cards you had a choice of either full duplex (used by default in XP) or another setting reached by right click properties of the card in Device Manager. I forget exactly but I think it's the Direct Sound support?that needs to be turned off within that properties panel to enable full duplex. It's an either or situation on these cards. If direct sound is on, the full duplex mode is deactivated. I think Direct Sound games would still work, just without the hardware buffer support. I guess you could just toggle that back on when gaming and off when conferencing. You probably need to restart the computer for the changes to take effect.

New xi-fi driver 5.12.17.1

availabla at station-drivers.com. didnt install by initially running setup, had to manualllt direct it t o extracted driver to install, sees to work fine , clicking and buzzing not noticeable at present
apologies didnt see it was already posted!Message Edited by sjh4 on 03-24-2006:5 PM

Hello Ego533,
Welcome to Creative forums!
Thank you for your feedback. The development team have been notified about this issue and will look into making this recognised as full duplex under Windows XP.
The Sound Blaster Team.<font face="Helv" size="2"><font face="Helv" size="2">
Message Edited by Loi-CL on <span class='local-date'> 04-0-2009<span class='local-time'> :05 [email protected]

My HP 4502 printer prints back to fronts do I change it to front to back

How do I get my HP all in one printer(4502) to print front to back copies

@betes, Welcome back to the forums!
I read your post about wanting to know how to duplex print with your Envy 4502. Check out the link below that will have the instructions for you to follow to help you print on both sides.
Click the link and select "Duplex in Windows".
Printing on Both Sides of the Paper (Duplexing) for HP Deskjet 3540, 4640, ENVY 4500, and Officejet ...
I hope this helps!
If you wish to send me a "thank you" for my response to help, click the thumbs up below!
R a i n b o w 7000I work on behalf of HP
Click the “Kudos Thumbs Up" at the bottom of this post to say
“Thanks” for helping!
Click “Accept as Solution” if you feel my post solved your issue, it will help others find the solution!

PhotoSmart 6520 e Printing Back to Back

Hi There Everybody
I Have Just purched the following printer and i would like to know how i do back to back to back printing with it to save on paper
if anyboby could help i would be very greatful

Hi MightyMan82,
Welcome to the HP Support Forums. I gather that you would like to learn how to print double sided using your Photosmart 6520 printer to reduce your paper and ink costs.
I have included the Printing on Both Sides of the Paper (Duplexing) in Windows document. It will walk you through how to set the default to double-sided printing or for the current document only. If you are a Mac user, I’ve included the Print Documents (Mac) document. It will explain how to change your presets for printing double-sided.
Regards,
Happytohelp01
Please click on the Thumbs Up on the right to say “Thanks” for helping!
Please click “Accept as Solution ” on the post that solves your issue to help others find the solution.
I work on behalf of HP

Sb 16 pci full duple

ok im running windows 98 with a soundblaster 6 pci and i cannot get full duplex why?i used to be running windows xp and i got full duplex fine could play 2 devices at once but with windows 98 i cant and i was wondering why i cant i play counterstrike and use ventrilo to chat at same time well when i start up the game it cuts ventrilo out so i cant talk and when im in the game i cant talk as well it cuts the sound off to ventrilo so that tthe game lets me hear but i cant hear the chat program so i get no full duplex on windows 98 please help how do i fix this

See the other post. You need to turn off Direct Sound in the Device Manager properties panel for the card for full duplex.

My Canon Pixma MG 7100 makes 2-sided printing the default. How can I change that to 1-sided for defa

My Canon Pixma MG 7100 makes 2-sided printing the default. How can I change that to 1-sided for defa

Hi janekieschninck,
If the printer is currently set to perform duplex (2-sided) printing, you can turn off the setting by deselecting the option in the printer driver. Please follow the instructions at the link below associated with your operating system to find where the duplex feature is located for your operating system:
Duplex printing - Mac
Duplex printing - Windows
Hope this helps!
This didn't answer your question or issue? Please call or email us using one of the methods on the Contact Us page for further assistance.
Did this answer your question? Please click the Accept as Solution button so that others may find the answer as well.

HP LaserJet 1320 Duplex Printing Not working with Windows 7

Hi
I've just bought a new PC with Windows 7 Home Premium. I have an HP LaserJet 1320 printer (Prod no. Q5927A, SN CNGW53RLRY).
I cannot find driver that works the same way as the previous driver HP LaserJet PCL5. If I use this driver and can still get duplex printing but it will only print one copy at a time.
If I upgrade to HP Universal Printing PLC (or PLC v5) I can print multiple copies but not duplex printing. I have searched high and low through the HP site but to no avail.
Any help and advice will be much appreciated.
Thanks
GB

Hello,
I've seen this same issue with my printers (other HP printers) whereby the default setting to support the Duplexing hardware was set to 'off'.
A quick method to check this is look at what the setting is for Duplex hardware in the Device Settings tab, and if it's not set, correct it.
Printer Properties:
From the 'Start' orb -> [Devices & Printers] -> right click on your Printer icon -> select 'Printer Properties' -> click on 'Device Settings' tab.
You should see a dialog similar to the mine (attached): look for the 'Duplex unit (for 2-sided printing)' and see if it's set to "Not Installed":
--> in either case, click on 'Not installed' and from the dropdown box, select 'Installed'... Click 'OK' to accept the changes and close the dialog.
Printing Preferences:
again, right click on your Printer icon -> select 'Printing Preferences' -> click on 'Advanced' tab.
-->Check to see if there is a 'Duplex Hardware' or '2-sided printing' option in here: mine doesn't show one but thougth I'd mention it nonetheless.
Click on the 'Finishing' tab and select 'Print on both sides'...or simply test print a multi-page document and set those preferences on-the-fly.
Let me know if this helps...
HardCopyTed
Regards,
HardCopy (I am employed by HP) [If this was helpful, please mark this 'Solved' or 'Accept as Solution' so others can find this too]
How to Give Kudos | How to mark as Solved
Attachments:
PCL6-DeviceSettingsScreenCap.JPG ‏81 KB

Automatic Duplex Printing not working on HP Color LaserJet 3600DN in Windows 7. It worked before.

I have an HP color laserjet 3600 DN on Windows 7. This computer came w/ Windows Vista and a 3600DN driver was installed and the computer was upgraded to Windows 7. The printer did automatic duplex printing.
At one point, my computer indicated that it could no longer find the printer. In an effort to solve this problem, I uninstalled the printer. When I tried to reinstall the printer the computer could not find the driver. At that point I tried to download a windows 7 CLJ 3600 DN driver. Since HP doesn't provide this driver for Windows 7, I tried to download the Windows Vista driver for 3600DN.
However, when I go to the appropriate webpage by following the links, only drivers for Color Laserjet 3600 are listed (no 3600DN drivers).
As far we can tell it only allows Manual Duplex printing (no automatic duplex printing). Clicking the "Two Sided Duplex Printing" option is there but only works when the "print on both sides (Manual)" is set on the Finishing page. If manual is turned off, then it becomes single sided.
Can I get a driver that will allow me to do automatic duplex printing on on my HP CLJ 3600 DN using Windows 7?

How did you replave the duplex belt? How to deassemble the backside of a officejet and click the new belt on? I can't see nor do it y self

Duplex printing. No dialog window on the HP LaserJet 1020

I'm running WinXP Pro, but I think it doesn't matter so much, because I've used duplex printing on it for a year without any problems. But now the dialog window, which must appear while using duplex printing is gone
When the Print on both sides instruction dialog window appears on the PC's monitor, follow the instructions, says the Duplexing Manual.
How to solve it, please help

Victory at last. OK, in case there is anyone out there who still has this (and start up no start) problems.
1. Delete the HP 1020 printer software via the Printers box from Control Panel (Visa 32 bit OS).
To do this, right click on the HP 1020 printer image, open the box, click on delete to remove the old driver & printer.
2. Go to HP 1020 site and find software downloads (words to that effect).
3. Download most recent driver (it is a plug and play driver -- currently [2-2011] there are 3 choices, this one is on top)
4. Install this driver. It will take a few minutes to complete
5. Plug in the printer and power up.
6 Once the dialogue box on the task bar says the printer is installed it's time to restart (if you look in the Printers Menu you probably won't find the printer. Don't panic yet)
7. Restart
8. Now look in the Printer Menu again. You 1020 should be there.
9. Test and good luck.
If this isn't the exact sequence for your computer, try a variation. The plug and play doesn't work on top of old software. Clear that old dog out and install the latest [Nov 2010 date] driver first, then plug in, then restart your computer.
Too Bad HP didn't publish this "fix" or even explain it on its woebegotten website. You can't drag this stuff up with a search engine. Next time you shop printers, tell the salesperson you deserve a big price break for putting up with all of this nonsense from HP.

HP Laserjet 1018, Word 2007 on Windows XP - Duplex printing alignment

HP Laserjet 1018, Word 2007 on Windows XP
Want to Print a book on both sides of A4 paper. I am printing one page per
page (not the book mode).
If I print single sided, the top of the page (e.g. header text) on odd and
even pages are aligned. When I print duplex mode, odd pages print fine but
the even pages are shifted down. Thus the header text are not aligned.
I think this is more a problem with the way the printer is managing duplex
printing.While printing in duplex mode, the printer first prints in reverse (with bottom of
the page as ref) to enable placement of the output sheets back into the input
tray without rotation. Is this messing up the alignment?
- Jayawanth

Hi there,
Try downloading and running the print and scan doctor located here:
http://h10025.www1.hp.com/ewfrf/wc/document?docname=c03275041&cc=us&dlc=en&lc=en
It can fix a lot on its own and if not give a better idea of what is going on.
Best of Luck!
You can say thanks by clicking the Kudos Star in my post. If my post resolves your problem, please mark it as Accepted Solution so others can benefit too.

HP Laserjet P2015d the full (automatic) duplexing feature incompatible with Windows 7??

I have an HP Laserjet P2015d which I bought specifically for the full (automatic) duplexing feature. This feature no longer seems to work under Windows 7 and I am beyond frustrated. I have tried several drivers and nothing seems to work.
I have tried both the P2015 PCL6 and the Universal PCL6 drivers and neither work.
I absolutely need full automatic duplex (2-sided) printing in my line of work. Manual duplex is not an option.
Please help!
Thanks,
Machelle

Hi Machelle,
Please verify the Duplex accessory is enabled within the driver configuration.
Enter Control Panel > Devices and Printers,
Right click the printer icon, then click Printer Properties.
Click the Device Configuration tab.
Make sure the Two-Sided Printing Accessory set as installed.
Then you should see the Two-Sided feature within the Printeing Preferences, under the Printing Shortcuts and the Finishing tabs.
Say thanks by clicking the Kudos thumb up in the post.
If my post resolve your problem please mark it as an Accepted Solution

HP Laserjet p2015d auto duplex printing with Windows 7 64 bit operating system

I have used the HP Laserjet p2015d with Windows 7 32 bit operating system and have been able to use the AUTOMATIC DUPLEX feature of the printer without problems.
Now, however, I have installed the 64 bit version of Windows 7 operating system and the AUTO DUPLEX does not work and is not shown as being available on the PROPERTIES menu of the printer.
Is it possible to use the AUTO DUPLEX feature of the printer with Windows 7 64 bit operating system.
All replies welcomed! Aaron in Calif.

Hi Aaron,
Make sure the Automatic Duplexing option is enabled:
Enter Control Panel > Devices and Printers.
Right click the printer icon, then click Printer Properties.
Click the Device Settings tab.
Set the Automatic Two-Sided Duplex Accessory as installed and click OK to save the change.
Now Automatic Duplexing should become available.
Regards,
Shlomi
Say thanks by clicking the Kudos thumb up in the post.
If my post resolve your problem please mark it as an Accepted Solution

HP 932c duplexer on Windows 7

Similar Messages

Maybe you are looking for