HP All in One officejet 4630 not printing

Hi all,
I bought my officejet 4630 earlier and haven't been able to print anything at all. When I press print it sends it the document to the printer but a few minutes later comes back with an error message. It scans fine and is connected through a USB as a wireless connection is not available in my office.
After uninstalling it and then installing it again it did not pick the printer up on the HP software used to setup the printer however it was picked up by the PC which after attempting to print a document came back with the same error message as before.
Thanks

Hey @M1XCE ,
Welcome to the HP Forums!
I understand you're unable to print to your Officejet 4630 printer.
Can you tell me which operating system you are using?
It might also help to try another driver. Changing the driver to the one in my steps below will not remove product functionality:
Go to Devices and Printers.
Right click on the 4630 printer.
Select Printer Properties.
Click the Advanced tab.
Click the New driver button.
Click Next >
Click HP from the list on the left.
Click HP Deskjet 9800 from the list on the right.
Click Next >
Click Finish.
Close the Properties window with OK.
Test the printer.
Let me know if that helps.
Please click the "Kudos, Thumbs Up" at the bottom of this post if you want to say "Thanks" for helping!
Please click "Accept as Solution" if you feel my post solved your issue, it will help others find the solution.
The Great Deku Tree
I work on behalf of HP.

Similar Messages

HP Deskjet all-in-one F4440 will not print

My HP Deskjet all-in-one- F4440 will not print. I have put in a new color and a new black cartridge. It clanks loudly when it moves back and forth. Finally it stops and then pulls plain paper through as though printing on it - does this two or three times. then it pulls plain paper halfway through and stops. I have to tug and carefully pull halfway paper back out towards front to remove.

Hi there,
Could you provide the community with a little more information to help narrow troubleshooting? Are there any error messages or flashing lights? What operating system are you using?
You can say thanks by clicking the Kudos Star in my post. If my post resolves your problem, please mark it as Accepted Solution so others can benefit too.

HP Deskjet All in ONe L7650 will not print black only --

Started doing this with previously working black cartridge, updated software--prints, but blank page comes out when set to black ink only; prints other colors.
Changed black print cartridge and still will not print black. Diagnostic page prints other colors.
Printhead health shows good for all colors.

What brand of printer cartridges (not printhead) did you use the last time you changed them? I don't know if it was because one or both of my printer cartrdiges went dry, but I put new cartridges in (not printhead) and it improved somewhat--I kept trying to clean the printheads but it seemed to never get resolved.
I refuse to have to buy new printheads. I tried several cycles of "align printheads" "clean printheads" and never got a decent print out, but I did get to the point of all the colors printing although magenta printhead makes printing errors and so I never know what I am going to get with color anymore.
It seems to be at its worst when printing in "draft" but in normal or best (with more ink coming through) it seems better--the higher ink volume seems to cover some of the problems with the printheads.
So, I am justing using it "as is" and not replacing the printheads--because it is a waste and yes, could almost get a new printer for this cost.
I wish I had never gotten this All in One and just stuck with the old 970 csi and the old UMAX scanner, which was a better scanner, but thought I would "save some space" by getting this since it scans legal, which I needed.
Just keep trying to reseat the printheads (also trying to reclean them, which seems to make it worse) and keep printing out those "tools" alignment and cleaning procedures.
But no help from HP.

HP 7510 All-in-one - alignment failed - not printing centered on page

HP 7510 All-in-one. I am getting alignment failed message at initial set-up. all colors print but text is not centered on the page.
Help!

Hi jillybeads99;
Hope you are having a great day and sorry to hear that you are having this issue;
Are you still experiencing this issue?
If you are, Try this uitility click here
I will do my best to assist you.
If you are not experiencing this issue any longer you may disregard this post, although I will deeply appreciate if you can take I little bit of your time and let me know.
Hope it helps;
RobertoR
You can say THANKS by clicking the KUDOS STAR. If my suggestion resolves your issue Mark as a "SOLUTION" this way others can benefit Thanks in Advance!

Why do I get a dent in the paper in the photo tray. I have 6280 all-in-one photosmart? not print

I have a 6280 all-in-one printer and it will not pick up the photo papar from the photo tray. It has a message that says load paper glossy side down. I have paper in there. when I examine the photo paper it has a dent in the end that is inserted first. Please help and thank you.

This is a user forum I feel you need to deal with Adobe customer services or support chat did not work in you case.

6110 All-in-one sometimes will not print multiple copies

I have had this problem for sometime now. I searched the forum and found the Mopier solution for laserjets, but the 6110 does not have this setting. The same question regarding the 6110 went unanswered in the only post I found for it.
I am using the 6110 on WinXP Pro and connected by USB
Often times when I try to print multiple copies of a document (MS Word or MS Works as examples) I check 2 copies in the selection box but the printer only prints one copy. I then have to click Print again. What is strange is, sometimes it performs fine and others it will not print more than one copy at a time. Sometimes it SEEMS that if I change the "collate" checkmark it works, but proper functioning does not seem to be able to be recreated every time.
I do not get any error messages, the darn thing just acts like I have 1 copy selected rahter than two. I notice that when this happens and I go to print a second copy, the dialogue box has reverted back to 1 copy, but in those few times when it DOES print 2 copies, if I go back and select Print, it still shows 2 for the number of copies.
Any ideas? Thanks in advance

Hi there,
To make sure the software side of the house is in order lets try downloading and running the print and scan doctor located here:
http://h10025.www1.hp.com/ewfrf/wc/document?docname=c03275041&cc=us&dlc=en&lc=en
It can fix a lot on its own and if not give a better idea of what is going on.
Best of Luck!
You can say thanks by clicking the Kudos Star in my post. If my post resolves your problem, please mark it as Accepted Solution so others can benefit too.

Hp all in one F2400 will not print!!

my printer will not print, all it will do is feed multiple pieces of paper through and print nothing and eventually getting jammed also the printer cartlidge goes back and forth making loud noise. i have no idea what could be wrong, it worked fine a few days ago. any suggestions would be appreciated.

I would try running the HP Print Diagnostic Utility. Go to http://h10025.www1.hp.com/ewfrf/wc/softwareDownloadIndex?softwareitem=mp-91788-1&lc=en&dlc=en&cc=us&...= and see what part fails.
The PDU checks the connectivity, spooler condition, online status, device manager, print queue, ports, driver, conflicts, and default printer.
Although I am an HP employee, I am speaking for myself and not for HP.
If I have resolved your issue, feel free to provide Kudos and make sure you mark this thread as solution provided.

After installing McAfee encryption on my XP laptop, my OfficeJet All-in-One 7410 will not print.

I have unstalled the software and now I can not reinstall the software. The diagnostic tool can see the printer, but the install software can not, even when I enter the IP address. I've turned off the firewall. I've connected the printer directly to the router. The only way to use the printer is through the USB which is not acceptable.

Hi there,
Try downloading and running the print and scan doctor located here:
http://h10025.www1.hp.com/ewfrf/wc/document?docname=c03275041&cc=us&dlc=en&lc=en
It can fix a lot on its own and if not give a better idea of what is going on.
Best of Luck!
You can say thanks by clicking the Kudos Star in my post. If my post resolves your problem, please mark it as Accepted Solution so others can benefit too.

Deskjet 1050 All-in-One J410e can not print in draft mode.

I wanted to print in Draft mode (300x300 dpi). I went to Avanced Options to adjust the resolution, but the drop down menu says "The following is for informational purposes only. Clicking on anything in this list will not change your Print Quality setting."
I was also unable to select Draft mode in the Preferences>Paper/Quality tab. Normal is automatically selected and the other options (Best, Draft, Custom) are grayed out.
What can I do to print in Draft mode (300x300 dpi)?

1st_HP_printer,
I believe the answer is best worded on Pg9 of the manual: http://h10032.www1.hp.com/ctg/Manual/c02227094.pdf
I am a volunteer. I am not an HP employee.
To say THANK YOU, press the "thumbs up symbol" to render a KUDO. Please click Accept as Solution, if your problem is solved. You can render both Solution and KUDO.
The Law of Effect states that positive reinforcement increases the probability of a behavior being repeated. (B.F.Skinner). You toss me KUDO and/or Solution, and I perform better.
(2) HP DV7t i7 3160QM 2.3Ghz 8GB
HP m9200t E8400,Win7 Pro 32 bit. 4GB RAM, ASUS 550Ti 2GB, Rosewill 630W. 1T HD SATA 3Gb/s
Custom Asus P8P67, I7-2600k, 16GB RAM, WIN7 Pro 64bit, EVGA GTX660 2GB, 750W OCZ, 1T HD SATA 6Gb/s
Custom Asus P8Z77, I7-3770k, 16GB RAM, WIN7 Pro 64bit, EVGA GTX670 2GB, 750W OCZ, 1T HD SATA 6Gb/s
Both Customs use Rosewill Blackhawk case.
Printer -- HP OfficeJet Pro 8600 Plus

My HP Photosmart all in one C4480 will not print from PC

I can't get my printer to print from my computer. Everything shows it's hooked up fine and ready to go. Yet when I try to print, nothing happens! Driving me crazy. Not sure if this is simply a bad printer or what. I've tried everything from unplugging, unhooking, rebooting, reinstalling, updating drivers and everything else. I've run out of ideas. Any new ideas would be appreciated.

Oddly @FlaBoy34, I did not get a notification that you had responded. I do see now that the issue you were experiencing remains. I suggest calling us to discuss your in/out of warranty options.
If you are in Canada or US call 800 474 6836, or you can Contact HP Worldwide.
HP printers generally have a 1 year warranty from their purchase date, you can verify the warranty using the following link if you would like; warranty check.
I hope this helps.
Please click the Thumbs up icon below to thank me for responding.
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Please click “Accept as Solution” if you feel my post solved your issue, it will help others find the solution.
Sunshyn2005 - I work on behalf of HP

My hp photosmart all in one 309a does not print PDF

I recently had to uninstall and reinstall the program, and now all prints fine EXCEPT Adobe PDF documents. Any Answers?
Thanks

Hi,
Sorry to take so long to reply. I was in San Francisco for the past week and only had my HP Touchpad with me. Try removing and reinstalling the HP Reader software program.
****Please click on Accept As Solution if a suggestion solves your problem. It helps others facing the same problem to find a solution easily****
2015 Microsoft MVP - Windows Experience Consumer

Deskjet 3520 All-in-One: Black Ink NOT printing....

I am highly irritated right now. My printer is 3 weeks out of warranty. I just spent $60+ in new ink cartridges today. The color cartridges are working fine, but the black ink does not work. The printer acts like it's printing, but nothing shows up on the paper. I see multiple people with this problem on this forum and other forums. I called tech support....went through an hour of "troubleshooting", then got disconnected. Called back and waited 45 minutes for another representative to tell me that he would sell me another printer for $100+ including some start-up ink cartridges that won't last me very long. I JUST bought $60 in ink cartridges TODAY. I have tried to take the printhead off with no luck. I can't get the printer apart in order to take the printhead off. I was going to attempt to clean it myself, but it's impossible to take the thing apart.
I am EXTREMELY dissatisfied with hp's customer service and feel that they should back up their product when it stops working only 3 weeks after the warranty expires. I would love if someone could tell me how I can fix this problem, since the printer is in basically new condition and has brand new ink.
It's unfortunate that these products aren't made to last longer than a year. I will not buy another hp product.
This question was solved.
View Solution.

Hi MarenB,
Please click on the link that I have provided for the ink related issue's. If this link is not successful, please let me know and we will attempt some other steps to get the issue resolved. http://goo.gl/Gf8orO
Thank you
Greenmarlock, Please use the following link for your Laserjet printer. http://goo.gl/eAVW02
If this link does not resolve your issue, please let me know and I will be more than happy to attempt to find a resolution for you as well.
Thank you both so much
Waterboy71
Click the “Kudos Thumbs Up" at the bottom of this post to say “Thanks” for helping!
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
W a t e r b o y 71
I work on behalf of HP

My deskjet All-in-one F300 will NOT print copy docs, or from My Docs or attachments

This printer will only print e-mails or direct from HP essentials screen but nothing else. Ink cartridges are ok.
Need help ...David Mullin

Are you printing it directly from a website? what is your computer's OS?
Although I am working on behalf of HP, I am speaking for myself and not for HP.
Love Kudos! If you feel my post has helped you please click the White Kudos! Star just below my name : )
If you feel my answer has fixed your problem please click 'Mark As Solution' and make it easier for others to find help quickly : )
Happy Troubleshooting : )

HP Photosmart C6300 All in one series is not printing

I have replaced all cartridges, and gone through the troubleshooting program for Ink System Failure with no success.
I have the HP Photosmart 6300 printer. I need your help.
Loreen Brigham

Hello Loreen,
Can you try printing a testpage by pressing Setup»Tools»Printer Status Report. Please scan this page and add it to your post by clicking the insert/edit picture button, so that i can have a look at it.
Say "Thanks" by clicking the Kudos Star in the post that helped you.
Although I work for HP my posts and replies are my own
Please mark the post that solves your problem as "Accepted Solution"

Hp photosmart 3210 all-in-one - some colors not printing even after changing cartridges.

I recently had an issue while printing a document. the content was off colored and the error message said black was low. Changed the black cartridge and things just got worse from there. Still no black, cleaned the printheads, printed another test page and no longer had magenta or lt magenta. Replaced those as well. the only had yellow, magenta and lt. magenta. yellow was low as well, so now every cartridge has been changes.Tried to print document again and it printed in magenta and lt magenta. never have seen black again and the self test diagnostic page is printing in purple. What should be black showed up as purple with lines and yellow is a rainbow of mustard, magentas and purples. no other colors show up. WHAT IS GOING ON? have tried several times to align the printer but it always fails. Have cleaned the printheads several time and just get a mish-mash of colors (no black) and most of the time no writing. When I try to print in black only, I get nothing.
What can I do? It worked just fine prior to ink going out.

Did you get a resolution to your problem? The same has occured for me - only printing blues/yellows and greens. Was working fine until I replace the yellow cartridge and then it stopped printing reds.

HP All in One officejet 4630 not printing

Similar Messages

Maybe you are looking for