HP All-in-one psc 2210

Changed printer cartridge (56) - which I have done many time without problem - pressed enter when requested to align printer cartridges & am now getting 'paper too narrow' error message.
I have tried to reset to factory default settings, realigning cartridges several times & clean printer acrtridges to no avail. I am beginning to believe this is a mechanical problem & in this case if there isn't a simple fix it woudl be better to buy a replacement.
Appreciate any ideas/comments?  

This is likely caused by the failure of one of your cartridges.  Remove the black cartridge and print a test page.  Does the printer print at normal speed?  Is so the black cartridge was the issue and should be replaced.  If not then put the black cartridge back in and remove the color cartridge and print test page.  If the printer now prints normal speed the color cartridge was at fault and needs to be replaced.
Bob Headrick,  HP Expert
I am not an employee of HP, I am a volunteer posting here on my own time.
If your problem is solved please click the "Accept as Solution" button ------------V
If my answer was helpful please click the "Thumbs Up" to say "Thank You"--V

Similar Messages

  • REGARDING CARTRIDGE ( HP 2520 ALL in One PSC and XP )

    Dear sir,
    I have purchased a new HP 2520 All in one PSC on Dec. 02 2013.  On dated 08-01-2014 blank pages comes out of print put or copy or both.
    I directly contact to 1800-425-7737 which is pasted on the printer. I told them that in the both cartridge showing signs one is 3/4  and other is 1/4.  They give me so many guides and tips and finally 2 test page comes out. They asks so many questions regarding the test page prints and finally advice not to worry
    They told me not to worry and advice me to go to Customer service center (DELHI --   Jabil Global Service, C-4, Second Floor, Ring Road , Rajouri Garden, New Delhi-110027) with my original bill copy, both test page and complaint no. and cartridge for replacement.
    ON 09-01-14 I reached there and they take my sign on the cartridge and rcvd. the documents. After a few minutes the person who handle the matter comes out and told me that cartridge was empty and come back with a rejection form.
    I am not signed the paper and came out.
    Now  Sir, please  let me know how can we believe on the service of the HP and why because some other companies who takes the HP service creating disbelief to customers.
    Please help me in this regard and please send one direct customer support engineer to my place.
    I am sending you all the reports and original bill for your verification as attachment.
    please do as soon as possible so that my works are pending.
    My complain no was[Personal Information Removed]
    With Best Regards and Beliefs
    [Personal Information Removed]

    I have forwarded your post to the right people for their review. You should hear back from someone shortly via Private Message on this forum.
    OrnahP
    HP Support Forums Moderator
     Clicking the "Kudos Star" to the left is a great way to say thanks!
     When your problem has been solved, accept the solution by clicking "Accept as Solution" to help other members in the future!
    Rules of Participation

  • All-in-one PSC 1410

    I was having lines trying to print in colour so I figured the ink was low. Changed cartridges with the proper HP coulour cartridge # 22 and all it does is print black? Anyone had this problem before? The old cartridge printed coulour but the new one doesn't - is this a cartridge mistake by HP or is there something wrong with the printer?
    Thanks for your help

    Hi acrylic,
    I understand you have a PSC 1410 that will only print in black despite you changing the color cartridge to a brand new one. I will certainly do my best to assist you with this.
    I would recommend that you follow this Check Print Cartridge Light Blinking document as it will guide you in cleaning the copper contacts of the cartridge and reseating it. You can also have a look through this Missing, Faded or Dull Colors document for a few extra steps.
    If the issue persists after this, you can certainly check the warranty date on the cartridge, and if it's in warranty you can call HP Tech Support for your area and inquire about a cartridge replacement.
    Hope this helps, have a great day!!
    Please click “Accept as Solution ” if you feel my post resolved your issue, as it will help others find the solution faster
    Click the “Kudos Thumbs Up" on the right to say “Thanks” for helping!
    **MissTeriLynn**
    I work on behalf of HP

  • PSC 2355-All-in-one

    My All-In-One PSC 2355 stopped printing multiple copies of a page, so I decided to re-install it.  After deleting the software, I found that my old disc didn't work with Windows Vista Home.  I have re-installed the compatible drivers from the HP website and all printing seems to be working fine, but it still will print only one copy of a page. Any ideas?

    I'm not sure what might have changed to cause this issue, but you may have to set the number of copies in two different locations.  First - set the number of copies when you click File and Print (which is probably what you're already doing).  Second - When you click File and Print from the app, click Properties and go into the Basics tab of the driver and set the number of copies in there as well.
    Sometimes, either the driver or the app will overide one another.
    Hope that helps.
    Say Thanks by clicking the Kudos thumbs up. Please mark the post that solves your problem as an Accepted Solution so other forum users can utilize the solution.
    I am an HP employee.

  • Enquiry regarding functionality of HP ALL IN ONE Q 1660A on windows 7

    Dear sir,
    I was using the referred HP 'ALL IN ONE(PSC) with Windows XP Professional version successfully.  Now I am having windows 7 in my desktop.  Kindly advise that the same HP " ALL IN ONE" would work on windows 7. Also please clarify whether the new driver is to be installed for the same.  If so please provede me the link from where I can download the necessary driver.

    Hello @parth_pari,
    Welcome to the HP Support Forums!
    I understand that you're looking for a Windows 7 driver for your HP PSC 1200 series All-in-One Printer. Upon looking into the driver compatibility for this printer I found that in Windows 7 you need to use the Windows Update feature on your computer to install the printer as HP does not have a downloadable Full Feature Software and Driver package available due to the age of the printer. There hasn't been a Full Feature Software and Driver available for this series of printer since Windows XP.
    You can still use the HP PSC on your Windows 7 computer.
    For instructions on how to install the printer using the Windows Update features, please click here.
    I hope this helps clear up any confusion!
    X-23
    I work on behalf of HP
    Please click "Accept as Solution" if you feel my post solved your issue, it will help others find the solution.
    Click the "Kudos, Thumbs Up" on the right to say "Thanks" for helping!

  • HP TouchSmart 600 and HP psc 2210 all-in-one printer

    Hi SiobhanF,
    I just registered and this is my first post.
    I recently bought a new PC...an HP TouchSmart 600.  My printer is a HP psc 2210 all-in-one.  I need advice on whether the two are compatible and if so how to get them working together.
    Thank you,
    waj

    This is likely caused by the failure of one of your cartridges.  Remove the black cartridge and print a test page.  Does the printer print at normal speed?  Is so the black cartridge was the issue and should be replaced.  If not then put the black cartridge back in and remove the color cartridge and print test page.  If the printer now prints normal speed the color cartridge was at fault and needs to be replaced.
    Bob Headrick,  HP Expert
    I am not an employee of HP, I am a volunteer posting here on my own time.
    If your problem is solved please click the "Accept as Solution" button ------------V
    If my answer was helpful please click the "Thumbs Up" to say "Thank You"--V

  • After the latest update printing off the web has moved from readable to font size 6. How to I get back to font size 10 or 12? hp psc 2210 all-in-one?

    When I print coupons or e-mail from my hp psc 2210 all-in-one the font has changed to 6 where before it was size 10 or 12. I have made no changes in my printer settings nor any other changes that I am aware of. This happened after the latest update of Firefox.

    I have a carriage jam on my HP Officejet 5510 which I cannot correct.. I have tried everything I know to do. There are two black pieces that will not spring down when the cartridges travel across. I th en get a carriage jam message.
    Do these pieces need lubricated?
    How can I get t hem to go down when the carriage goes across?
    Thanks for any information or help options
    Karol

  • Psc 2210 all-in-one.

    I have an old workhorse, a psc 2210 all-in-one. Can I easily turn the color off and on? Anybody know?   Thanks.

    Does the printhead take a swath and then delay 10-15 seconds before the next swath?  Does the delay also happen when you make a copy?  If so likely one of the cartridges has failed.  Try removing the color cartridge and printing (not copying) a page.  Does the page print at normal speed?  If so the color cartridge is at fault and should be replaced.  If not then remove the black cartridge, put the color cartridge back in and try printing a page.  If the printing now completes in approximately normal time then the black cartridge was at fault and should be replaced.  
    If the failed cartridge is an original (not refilled or reman) HP and not empty you can check the warranty information as shown here.
    Bob Headrick,  HP Expert
    I am not an employee of HP, I am a volunteer posting here on my own time.
    If your problem is solved please click the "Accept as Solution" button ------------V
    If my answer was helpful please click the "Thumbs Up" to say "Thank You"--V

  • HP psc 2210 all in one printer hung up

    My HP PSC 2210 is stuck with an internal software hang up. It thinks it is printing a job, but there is no job, it also (correctly) wants to align the cartridges, but when I press enter to do this is says it is busy printing.
    (I have cleared any print jobs from the computer print queue).
    It will not copy or anything either , because it is trying to align the cartridges. any attempt to print test pages etc similarly fails, whether from the computer, or direct from the printer.
    I need to reset the internal memory of the HP PSC 2210 in some way.
    I have tried powering up with # and 6 held down, this effected some sort of reset, I had to choose the language again.... but I cannot get rid of the phantom print job.
    I cannot even switch the wretched thing off with the power button any more ?!
    any advice greatly appreciated

    This is likely caused by the failure of one of your cartridges.  Remove the black cartridge and print a test page.  Does the printer print at normal speed?  Is so the black cartridge was the issue and should be replaced.  If not then put the black cartridge back in and remove the color cartridge and print test page.  If the printer now prints normal speed the color cartridge was at fault and needs to be replaced.
    Bob Headrick,  HP Expert
    I am not an employee of HP, I am a volunteer posting here on my own time.
    If your problem is solved please click the "Accept as Solution" button ------------V
    If my answer was helpful please click the "Thumbs Up" to say "Thank You"--V

  • HP PSC 2210 all in one printer - slow printing

    I have had this all in one printer for several years.  Just recently I attempted to print two pages from a PDF file and it took over 1 hour to print.  At first I thought it was the PDF but now I realize it is with anything I try to print.  I went through all the troubleshooting steps and none of them have fixed the problem.
    I have a Dell Dimension 8400 Intel Pentium Computer,  Windows XP 4 cpu 3.20 GHz, 3.19 GHz, 1.00 GB of Ram.
    It will begin to print but then it will take at least an hour to print 1 page.  I have already uninstalled, re-installed, etc...
    This question was solved.
    View Solution.

    This is likely caused by the failure of one of your cartridges.  Remove the black cartridge and print a test page.  Does the printer print at normal speed?  Is so the black cartridge was the issue and should be replaced.  If not then put the black cartridge back in and remove the color cartridge and print test page.  If the printer now prints normal speed the color cartridge was at fault and needs to be replaced.
    Bob Headrick,  HP Expert
    I am not an employee of HP, I am a volunteer posting here on my own time.
    If your problem is solved please click the "Accept as Solution" button ------------V
    If my answer was helpful please click the "Thumbs Up" to say "Thank You"--V

  • How do I install driver for hp psc 2400 all in one series AND safe wsnmp32.dl​l Without a Disk?

    How do I install driver(s) for hp psc 2400 all in one series ( WIndows 7 laptop)   AND a safe version of wsnmp32.dll -- Without a Disk?    A tech took the driver off my laptop and I now have no printer/scanner.  Help!!
    Much thanks!

    Hello,
    I see that you're having an issue installing the software. I would suggest following this document, which will guide you through several steps on how to resolve the issue.

  • Can I share HP PSC 1610 All-In-One series printer through Bonjour?

    I have an iBook G4, and a Mac Mini (10.4.11- Tiger) with a HP PSC 1610 All In One series printer connected to it by USB. On my iBook G4, the printer comes up under Shared Printers in the Printer Setup Utility but when I click on it, and press Show Info it freezes.. so I was wondering, is there a way to connect to the printer wirelessly with the correct driver (because the driver doesn't show up in the driver list... and the driver is installed.)

    Hi my printer psc 1610 hp not picking paper

  • HP Officejet and PSC Full Feature Software for HP PSC 1210 All in one printer

    Hello ,
                 I have  HP PSC 1210 All in one printer but i am using windows 7 system.how can i find
                                                                                'HP Officejet and PSC Full Feature Software'
    compatible for windows 7, in hp.com i sould find the above software for windows xp but for windows xp its not working, my printer physical keys are not working so i need software to do everyything from print to scan, copy etc from my windows 7 laptop itself. pls help with sofware for windows 7

    Hi,
    There is not a full feature software Win 7 download available for the HP PSC 1210. The following document includes instructions on how to install the in-OS Win 7 driver with instructions on how to scan:
    http://h10025.www1.hp.com/ewfrf/wc/document?docname=c01796879&cc=us&dlc=en&lc=en&os=4062&product=907...=
    I work for HP.

  • How can I fix a check paper error on the HP psc 1210 all in one printer?

    Product name/number:  HP PSC 1210 all-in-one
    OS:  Windows 7
    Error Msg:  Check Paper light flashes
    I have verified there are no paper jams, paper is loaded, print cartridges move freely and rollers are clean.  Is there a a paper out switch that can fail?

    Hi there,
    This article should cover the issue you are experiencing. Give the steps outlined a shot and let us know if it helps.
    Best of Luck!
    You can say thanks by clicking the Kudos Star in my post. If my post resolves your problem, please mark it as Accepted Solution so others can benefit too.

  • Looking for basic driver for psc all in one 2175 for XP 32 bit. Thank you

    looking for basic driver for psc all in one 2175 for XP 32 bit. Thank you Dont need all the photo suite stuff,just basic scan and print.
    Thanks

    Hi @RUkiddingme 
    You can download the full feature software and driver, and only install the basic driver. In the installation you should see the option for custom software. Here is the link to download the software; rw2_021_w02_enu.exe
    Please let me know if this resolves the issue.
    Please click the Thumbs up icon below to thank me for responding.
    ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
    Please click “Accept as Solution” if you feel my post solved your issue, it will help others find the solution.
    Sunshyn2005 - I work on behalf of HP

Maybe you are looking for