HP Battery Check Status: replace (41)

Hello Guys.
I have an issue with my laptop battery. Laptop shuts down immediately after power chord is removed and wont boot until I reconnect it.
I have been using this battery for 4 months and it's 5200mAh 8cell battery. Windows says that battery is 100% charged
Hp Battery Check status is replace (41)
help?
I'm using a HP Probook 4510s with windows 8 OS.
Thanks in advance.

Sounds like your battery is not functioning properly. I would first run a battery calibration on your laptop. ProBook Battery Calibration. If this does not solve the issue then most likely the battery needs replaced. Are you still in warranty?
Thanks
Sean
-------------How do I give Kudos? | How do I mark a post as Solved? --------------------------------------------------------

Similar Messages

Battery check primary replace 42

I recently got a boot loop on my computer so when I ran the system and component checks the thing that failed was the primary battery. In hopes that that would solve the problem of the boot loop I got a new battery. It arrived and when I put it in I still got the boot loop so I went back and ran the system and component check again and it says to replace the primary battery. Any help would be appreciated. Thank you.

Hi,
Thank you for providing that information.
As you were doing a system restore, where did you do this from? I would have to guess safe mode?
If you can get into Safe Mode, try doing a clean boot. The issue you're describing sounds more like a probably with the OS loading drivers or software on boot. The clean boot should eliminate the software/applications if they are the cause. It won't impact if it's a driver. However, a Restore to a point prior to the issue should have.
As yo're running 8 or 8.1 you will also have the option of doing a Refresh (provided you can get into safe mode) if neither a clean boot or restore are allowing you to boot normally that would be the next option. You will lose installed application when doing a refresh.
The final option and more for if you can't even get into safe mode is a system recovery.
I hope something here can help, let me know how it goes.
I worked on behalf of HP.

HP Battery Check Shows Status 80

Can Anyone Please Tell Me The Meaning of Status: 80 (Circled With Red)

Hello @HPUSER1102 ,
Welcome to the HP Forums!
Status 80 of the advanced HP Battery Check indicates a perfectly healthy battery! Congratulations
Mario
I worked on behalf of HP.

The battery check on my Pavilion dm3 has failed with the message "Replace (00000040)".

It's just over a year old and will now only work when plugged in to the mains. The battery has always been pretty good and there has been no warning or degradation of performance in the last week or two.
I know it may sound like a stupid question given the result of the battery check, but do I really need a new one or is there anything else I can try first?

okay
first try this:
remove the battery, other peripherals and the AC adapter... press and hold the power button for 20 seconds... plug the AC adapter only and turn on the notebook....
and then:
Click Start and type device in the search field, then select Device Manager.
Expand the Batteries category.
Under the Batteries category, right-click the Microsoft ACPI Compliant Control Method Battery listing, and select Uninstall.
Warning: Do not remove the Microsoft AC Adapter driver or any other ACPI compliant driver.
On the Device Manager taskbar, click Scan for hardware changes.
Alternately, select Action > Scan for hardware changes.
check whether the battery is getting charged or not...
get back to us with the product number (p/n) written on a white sticker at the bottom of the notebook... and OS with version (32/64-bit)
||-Although I am working on behalf of HP, I am speaking for myself and not for HP.-||
//Click on Kudos if my reply was helpful and answered your question//
||-If my answer solved the problem please mark the topic as the accepted solution-||

Battery checks say change battery, but it charges and works fine. Help?

Hey there,
Just having a problem with my Laptop battery. My product type is a HP G61 Notebook PC. The battery icon in the bottom left says the battery should be replaced, with checks saying it has reached the end of it's useful life.
I find this hard to believe since I've had the laptop a year and it still charges and works fine. I don't want to spend any unnecessary money at the moment so I'm not sure whether to wait and ignore it to see how it goes.
Suggestions?

Hi,
Jamie2812 wrote:
Hey there,
Just having a problem with my Laptop battery. My product type is a HP G61 Notebook PC. The battery icon in the bottom left says the battery should be replaced, with checks saying it has reached the end of it's useful life.
I find this hard to believe since I've had the laptop a year and it still charges and works fine. I don't want to spend any unnecessary money at the moment so I'm not sure whether to wait and ignore it to see how it goes.
Suggestions?
I suggest that you perform a calibration of your battery.
regards,
erico
****Please click on Accept As Solution if a suggestion solves your problem. It helps others facing the same problem to find a solution easily****
2015 Microsoft MVP - Windows Experience Consumer

Software not checking status of applications

Hi, first time poster and new owner of an 8120. I am having problems with the software. At first I selected the option that allows connection of work emails and had to remove the software and start again.
The second time, the software loaded perfectly. However there is one stumbling block. The one time 'checking status' part of the loading process doesn't work. I get the following message, the system looks as if it's working..checking something..and then stalls.
" Checking the status of the applications on the device. This is only required on the first connection of the device to a new desktop installation."
I left the think on for the whole of last night, assuming that this process might take a while. 7 hours later it has still not progesssed.
Has anyone got any ideas, beyond removing the software and trying again? Any heal appreciated.
Solved!
Go to Solution.

Ok got the answer... I think. I actually read a response to a similar query in here. Basically - I kept the phone connected via the USB cable and whilst connected I removed the battery. In about .5 of a second the status was checked. So wierd!
I reconnected the battery, shut down the blackberry desktop software, reloaded again and then alacazam! It worked.

Battery check script

Hi all! I'm sure this one has been done to death, but with. It's a script to monitor a laptop battery and react accordingly. I wrote this for use with FVWM, to send out warning notices using libnotify when the battery gets too low. Since my laptop is quite old, the battery runs out quite quickly after getting to 25% capacity. The script backgrounds itself on being run. It starts when I begin an FVWM session, and I have FVWM kill the script when I logout.
Being a script it's easy to tweak to your particular requirements. The example below just warns, but it would be easy to have the script suspend or hibernate the system, or change the percentage charge at which the script performs different actions. I hope it's useful.
#!/bin/bash
# battery check script
# ====================
# Designed to be run continuously while WM is running
# Requires libnotify to be installed
ICONPATH=/home/rob/.fvwm/icons/24x18
BATDIR=/sys/class/power_supply/BAT0
NOTIFYSEND=/usr/bin/notify-send
if [ ! -x $NOTIFYSEND ]
then
exit 0
fi
# check every $CHECK seconds
CHECK=60
( while true
do
BATSTATE=`cat ${BATDIR}/status`
# Note valid BATSTATE values are: Charged, Charging, and Discharging
if [ "$BATSTATE" = "Discharging" ]
then
REM_CAP=`cat ${BATDIR}/charge_now`
FULL_CAP=`cat ${BATDIR}/charge_full`
CHARGE=`echo $(( $REM_CAP * 100 / $FULL_CAP ))`
if [ "$CHARGE" -lt "25" ]
then
$NOTIFYSEND -i $ICONPATH/battery_critical.png -u critical -t 30000 "battery critical" "Shutdown or connect power now"
sleep $CHECK
continue
fi
if [ "$CHARGE" -lt "30" ]
then
$NOTIFYSEND -i $ICONPATH/battery_low.png -u normal -t 20000 "battery low" "Connect power soon"
fi
sleep $CHECK
elif [ "$BATSTATE" = "Charged" ]
then
$NOTIFYSEND -i $ICONPATH/battery_full.png -u normal -t 20000 "battery fully charged" "Disconnect from power"
sleep $CHECK
else
sleep $CHECK
fi
done
# end of file
Edited 21/10/2011 to use /sys/class/power_supply/BAT0 instead of /proc/acpi/battery/BAT0
Last edited by Painless (2011-10-21 12:48:05)

I'm not exactly sure what you're trying to accomplish; your script seems to me to be prone to high cpu-useage loops. If all you want is a warning message if your battery is low when your adaptor is not plugged in, then you could try the following script.
One caveat, I don't have a laptop and I don't know what the output of
acpi -b
looks like, so I don't know which field contains the battery charge info. In the script below, I'm guessing that it is field number 3, so if it is different than that, the script below is incorrect and will not work.
If you don't understand what I am talking about, run
acpi -b
on your laptop, and post the output for me.
#!/bin/bash
trap "exit" SIGINT SIGTERM
delay=60
warning=50
while :
do
adapter=$(acpi -a | grep on)
b=$(acpi -b | cut -d ' ' -f 3)
[[ -z "$adapter" && "$b" -lt "$warning" ]] &&
notify-send "WARNING - LOW BATTERY" "Battery has ${b}% left."
sleep $delay
done
Last edited by rockin turtle (2011-01-15 06:08:45)

Battery check compaq presario cq56

is safe to run a laptop just withe a/c after the battery is charged, and if is posible repair the Hp assistant aplication is not working properly?? are any others programs to check is the battery status Gracias

Hello,
I see that you're having an issue with HPSA not working properly. Now, I'm not aware of any other 3rd party program that gives you the ability to check your battery’s performance.
Now, to resolve the HPSA issue you have going on. You will need to uninstall the program through the Add/Remove folder in the control panel. After that, you will need to install this version of HPSA. Once you install that you should be able to use the battery check within the program.
If the issue still persists please let me know. If you have any more questions let me know.
THX

Bluetooth Mouse battery Power Status

Re:
ThinkPad Bluetooth Laser Mouse
How to check remaining power and set low power notification for Bluetooth keyboard and mouse
With Windows 7x64 running on a T420s, Control Panel > Mouse has a Bluetooth tab that shows battery Power Status.
However, with Windows 8.1x64 on a T450s, there is no Bluetooth tab or any other battery power status that I can find.
Has this functionality been lost?
Hope that helps,
John
ThinkPad T450s [ i7-5600U | 8GB | 1TB SSD | Full HD IPS | 802.11ac | BT | Webcam | FR | Win8.1Pro64 ]

Alkaline batteries will give you the longest life in the mice, but, you have to dispose of them properly, and, buy new ones.... (bad).
Apple sells the Apple Battery charger, that has 6 high capacity NiMH batteries for $30.00
They won't last as long as alkaline, but, simply put the pair of extra (charged of course), into the mouse, the old ones to be charged... Supposed to last over 1000 chargers.
Here's the link: http://store.apple.com/us/product/MC500LL/A?mco=MTY3ODQ5OTY

CHECK status transaction in SRM 7.0

Hi all,
We are on SRM 7.0.1.
What is the corresponding transaction/link in EP in SRM 7.0f or "CHECK STATUS" transaction in SRM 5.0?
Thanks.

Hi,
You have POWL which replaces Check Status. POWL has diferrent set of queries for each business object and in fact you can create your own queries as well.
Regards,
Prasanna

PRAM battery checker

Has anyone used - safely and successfully - the PRAM battery checker application found here:
http://www.polar-orbit.com/software.html
Thanks,
Mrs H

Will the battery slowly poop out and give me warning signs or just die? When I replace the battery do I just have to reset the clock or are there other settings that are lost?
People often think that having a bad battery doesn't make any real difference other than having to reset your clock. This battery may be essential for PRAM operation even if your computer is plugged in. A bad battery can corrupt PRAM and cause startup problems, but it has to be in the computer or the computer won't start at all, so if it is starting to go you are forced into a corner. PRAM stores other startup information about your computer, not just date and time. Some people experience startup problems with a bad PRAM battery. The computer may have to hunt for a startup disk or forget their preferred startup disk, especially if you have more than one drive. The monitor may not come up although the computer starts. Read the links provided earlier for details.
The more you leave your computer unplugged (vs. just turned off but still plugged in) the faster the battery will drain. I leave my computer plugged in all the time and have gone at least 5 years without needing a battery. If I unplug a computer it may only last a few months (maybe, not sure exactly how long, only did it once).
A battery on the edge of going may be able to recover slightly if you plug a computer back in.
Do you need to replace it? It depends upon how safe you want to play it. I have a spare in a drawer somewhere. I have also been able to continue to use a computer with a bad battery though I sometimes had to baby it on startup - multiple tries, reset clock. The cheapest batteries can be bought online. It's not a size commonly stocked. National battery specialists/computer stores may have them but they cost more. If you're out in the boonies and don't like hassle then get a replacement. Think of a car with a weak battery. If you want to be sure it will start immediately and be there when you need it then it's only a matter of maybe $5 +$5 shipping every now and then. As I said, I have a spare in a drawer and have several computers that all use the same size battery.

BBPSC04_ Disable auto conf and auto inv from SC check status

Hello,
I would like to disable the auto confirmation and auto inv buttons from the shopping cart check status only and the user should be able to do confirmation from Confirm goods/services.
kindly suggest how can we acheive this?
Thanks & Regards,
James

Hi
you can try ith BADI
BBP_SCREENVARIANT ( BUS2121) .
You can replace screen variant bbp_search_sc with your user defined screen variant YBBP_SEARCH_SC in the method of get_screenvariant_search.
Hope that you got it.
regards
Muthu

SRM 7.0 Modify POWL for shopping cart check status screen

HI Experts,
The standard settings in check status for SC in SRM 7.0 is to display the sc with item level. This causes the SC number to be repeated (for no. of items in SC) and all links open the same SC in a new window.
We want to display only the header of SC and no item data should be displayed in check status.
I tried
SRM Server->Cross-Application Basic Settings->POWL and Advance Search->Adjust POWL Layout,search criteria and push buttons----choose feeder type SAPSRM_FEEDER_SC -double click field catalog-choose ITEM_DESCR, ITEM_NO, ITEM_STATUS---CHOOSE display and select HIDDEN COLUMN radio button.
This hides the corresponding columns but duplicate records are still showing.
Can some one please help?
Thanks,
Anubhav

Hi NM,
After performing the steps in first post for hiding item relevant fields you can filter the data displayed in the result by using the BADI /SAPSRM/BD_POWL_CHNG_SEL_RSLT .
In the BADI Delete the records from result internal table where SC num is repeated so that thers only one entry for each SC.
Let me know if it works for you or not.
BR,
Anubhav

Changing the dropdown values for one of the fields in CHECK STATUS query

Hi,
We are on SRM 7.1.
In the CHECK STATUS transaction,in the selection screen(QUERY),there is a field called "ROLE" which has teh dropdown values of "APPROVE BY ME","REJECTED BY ME" and "GOODS/SERVICES DELIVERED TO ME".Is there any way some of these drowpdown values can be removed?
Please advise.

hi nmsrm1234
i have a document for this issue.
but i don´t find this document in internet. it is called : CUSTOMER-SPECIFIC UI ADJUSTMENTS IN SRM 7.0 WEBDYNRPO ENVIROMENT / META DATA HANDLING CONCEPT.
if you can find it, you will get an idea to resolve this issue, if you will no have luck, please get me your mail, and i will send you the document.
regards.

Change the input parameter in Check Status screen

Hi,
I have a requirment to change the input parameter option in the check status screen. Currently when we search the SC using the date and staus from the extended search it picks the SC created date and displays the SC, my requirement is to make the date as the approved date insted of SC created date with the status as aprpoved.
Please suggest if this is possible with the help of any Badi.
Regards
GGL

I managed to find the solution myself. If anyone is interested, just follow those steps here:
http://apple.stackexchange.com/questions/44913/make-a-custom-keyboard-layout-the -system-default-even-for-the-login-screen
(terminal skills required tho)

HP Battery Check Status: replace (41)

Similar Messages

Maybe you are looking for