HP Color Laserjet Series CM6040 MFP- DRUM error

Hi, I changed yesterday the color drums (Cyan, Magenta, Yellow) in this printer model but the counters doesn't reset, they are at 0% and the 3 color drums are new, in the printer don't exist a reset point...
The firmware is: 20081205 52.031.1
I changed the 3 at the same time....
What did I do wrong?
Any Ideas?
Somebody knows how to resolve this problem?
THX
This question was solved.
View Solution.

For us it has been about 18 hours and the counter still didn't reset going to power cycle the printer and see if that helps. 

Similar Messages

  • HP color laserjet CP2025dn and encountered an Error 58.04

    I have a HP color laserjet CP2025dn and encountered an Error 58.04, any suggestion on what to do?

    Hello there,
    To get your issue more exposure, I would suggest posting it in the commercial forums since your product is a commercial product. You can do this at Commercial Forums - Printers - LaserJet.
    Enjoy your day!
    R a i n b o w 7000I work on behalf of HP
    Click the “Kudos Thumbs Up" at the bottom of this post to say
    “Thanks” for helping!
    Click “Accept as Solution” if you feel my post solved your issue, it will help others find the solution!

  • Paper jam in color laserjet 2840. broken paper removed, error paperdraw stays in display. Windows 7

    I had a paper jam in my HP Color LaserJet 2840 printer. I removed the broken paper. Then it hapenned again.
    Removed the broken paper for the second time and now the error about the paper draw stays in the display.
    Also when I restart the computer os turn off the printer. I also looked in the inside of the printer but I can't see anything. 
    This question was solved.
    View Solution.

    The troubleshooting page here may help.
    Bob Headrick,  HP Expert
    I am not an employee of HP, I am a volunteer posting here on my own time.
    If your problem is solved please click the "Accept as Solution" button ------------V
    If my answer was helpful please click the "Thumbs Up" to say "Thank You"--V

  • Laserjet Pro 400 MFP 451dn error message 58.04

    Does somebody know the meaning of this error message ?
    I'm not able to reset this message even I tried to switch off and on again
    several times as recommented
    Thank you in advance
    P.S. This thread has been moevd from Laserjet to Multifunction and All-in-One. -  Hp Forum Moderator

    If the printer is not plugged directly into the wall socket plug it directly in bypassing surge protector and see if that solves the issue. If it does not then the low voltage power supply needs to be replaced. If under warranty call hp to find a local service provider. If not under warranty, below is the part needed if you want to try it yourself.
    Low voltage power supply PC board assembly - Input voltage 110VAC-127VAC RM1-9034-000CN
    Low voltage power supply PC board assembly - Input voltage 220VAC-240VAC RM1-9036-000CN

  • Color Laserjet Pro 200 MFP Print Menu

    When I use my iMac 27 with this printer, I don't see all the print options in the print menu in Preview etc. that are mentioned in the User Guide.  No "Color/Quality" options/Advanced  etc. to change.   I have downloaded and installed the latest drivers from HP.  I am using OS X 10.9.4.  Am I doing something incorrectly or missing something.  The product is working fine otherwise.
    This question was solved.
    View Solution.

    Hi jerryoster,
    It sounds to me from your description that you might be using the Mac AirPrint driver instead of the HP driver. I suggest the follow;
    Reset Printing System
    Click the Apple icon (   ), and then click System Preferences.
    In the Hardware section, click Print & Fax/Scan. The Print & Fax/Scan  dialog box opens.
    Right-click (or  Ctrl  +click) in the left panel, and then click Reset printing system…
    Click OK to confirm the reset.
    Type the correct Name and Password.
    Click OK to reset the printing system. The Print & Fax dialog box shows no printer selected
    Note: This will remove all printers in the print and Fax/Scan, any printer removed can be re-added later by clicking the plus (+) symbol.
    hen you add the printer, ensure you are using the HP driver, not the AirPrint driver.
    Select Add other Printer or Scanner                                                       
    Select the printer you are adding and next to 'Use' you can the printer driver 
    Please let me know if this resolves the issue. If you require further assistance, let me know which LJ 200 model you have (How Do I Find My Model Number or Product Number?),  and if you have downloaded and installed the full feature software and driver from the HP website.
    Please click the Thumbs up icon below to thank me for responding.
    ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
    Please click “Accept as Solution” if you feel my post solved your issue, it will help others find the solution.
    Sunshyn2005 - I work on behalf of HP

  • I have a HP Color LaserJet 1525NW and it caught "Error 49"

    I did all I could, unplugging it turning it off letting it sit unplugged all night, for it and it is still flashing ERROR 49 is there hope for it can it be repaired?

    Hi,
    Ensure you have the latest firmware which seems to deal witrh the specific error:
    http://h10025.www1.hp.com/ewfrf/wc/softwareDownloadIndex?softwareitem=lj-86474-1 0&cc=us&dlc=en&lc=en&os=219&product=4052980&sw_lang=
    Fixes: Fixed several issues including a 49 error and incorrectly handling the number of copies for some types of Postscript files.
    If the same persists also follow the steps listed as 49 Error below:
    http://h10025.www1.hp.com/ewfrf/wc/document?docname=c02184434&cc=us&dlc=en&lc=en &product=4052980&tmp_track_link=ot_search#N60
    Shlomi

  • HP Color Laserjet CM 1312 MFP / Won't Scan!

    Hi guys,
    I have been on the phone to HP for days they are blaming my computer but really it doesn't sound right... Brand new iMac, and a brand new CM1312... I have plugged it directly into the back of the computer via the USB the computer sees it and there is no problem with printing... BUT using the HP Scanner software it cannot see the printer via USB... I used the HP Set Up Wizard and when it comes to the screen asking to find the USB or Network printer it can't see it under USB, EVEN THOUGH IT PRINTS VIA USB... Has anyone had this issue before? Am I better off using an ethernet cord?

    Hello Tom:
    I do not have the same printer, so I am fishing a bit.
    I have read here that all-in-one devices only print when using the built-in OS X drivers. Those with that particular problem have had some success by doing what you have tried - namely installing the manufacturer's software.
    You might try uninstalling the printer, and then starting over with HP's software.
    My own printer is Ethernet-connected, but I do that so it is available on my little home network. candidly, I prefer Ethernet connections over USB, but that is a personal preference, not an indictment of USB.
    Barry
    Message was edited by: Barry Hemphill

  • Fuser error for HP Color LaserJet 3600 Series Printer

    My HP Color LaserJet 3600dn  Printer have  Fuser error message.  What is the problem ?

    The product you have seems to be a commercial printer. For the best chance at finding a solution I would suggest posting in the forum for HP Business Support!
    You may find the Commercial Laserjet board here.
    http://h30499.www3.hp.com/t5/Printers-LaserJet/bd-p/bsc-413
    You can also view the article related to this product here:
    http://h20000.www2.hp.com/bizsupport/TechSupport/Home.jsp?lang=en&cc=us&prodTypeId=18972&prodSeriesI...
    Hope this helps!
    Help the community by marking this post as a solution if it solved your issue!.
    If my post helped you in any way, please click the blue KUDOS star under my name! It would mean a great deal.

  • New color laserjet pro mfp m177 will not scan or copy

    Product is new. The problem is that this unit will not scan or copy.  I downloaded the latest drivers, but they would not install completely.  I also ran thru some trouble shooting guides on the HP website, but still it doesn't work.  It tries to make a copy, but it acts like it starts and then stops without completing the function.  It's almost like the scanner mechanism is stuck.  Anyone ever have this problem with a brand new printer?

    Hello , Thanks for posting in the HP Forums, and welcome! I understand you are unable to make a copy or scan on your new HP Color LaserJet Pro M177fw MFP. I'd like to help you with this. Firstly, do you have the printer connected directly to a wall outlet or is it in a surge protector or power bar? Even if you have been using a surge protector/power bar all this time and you feel it is not the cause, please connect it to a wall outlet just so we can eliminate the power source as the root cause. Issues when Connected to an Uninterruptible Power Supply/Power Strip/Surge Protector
    In this document you will see, ISSUE: Problems or issues may arise when an HP LaserJet series printer is connected to an uninterruptible power supply (UPS), a power strip, or a surge protector
    ^ This is not limited to Laserjet printers. If the issue persists, I would suggest download and installing the most recent firmware for your unit. You can download the firmware update utility here:HP Color LaserJet Pro MFP M177fw Firmware UpdateNote: You will need to connect the printer via USB to update the firmware, as any interruption during the firmware update can cause more issues. If this still does not resolve the issue, please let me know if you are getting some sort of error message on the screen or any blinking lights to indicate what the problem may be. Hope this helps!

  • Doesn't feed paper. color laserjet pro mfp m177fw

    I just bought the Color Laserjet Pro MFP M177fw. I removed all the packing as instructed in the installation guide.
    While initializing the printer makes a strange noise. When I try to print it gives me a message to load paper. No matter how much paper I load in tray 1 it gives me the same message.  I removed the paper and tray 1. Then using a torch I looked in the bin and I don't even see the white metallic rod  moving when I give a print command. I suspect that there is something stopping the metalic rod from rotating. I see two black clips on both ends of the rod. Manual didn't mention it but was I suppose to take them out? Or there is another problem?
    Need help.
    Thanks
    FKK

    Hi @fkk ,
    I read your post and see that the new printer is initializing and the printer makes a strange noise. You are also getting the message to "load paper". I would really like to be able to help you resolve this issue.
    It sounds like there might be some more packing material inside the printer.  Please check and remove any packaging material inside the printer. Here is a document for Setting Up the Printer Hardware for HP Color LaserJet Pro M177fw MFP Printers.
    Disconnect the USB/Network/FAX and power the printer on Standalone.
    Do a hard reset to see if that will resolve the issue.
    Leave the printer on and unplug the power cable from the printer and wall outlet for 60 seconds.
    Then reconnect the power cable to the printer and wall outlet rather than a surge protector.
    This ensures the printer is receiving full power and may help this situation.
    If the issue persists, perform a power drain by disconnecting the power cord from the back of the printer and keeping the power button pressed for 30 seconds and in case of a power switch keep the switch in ON position for 30 seconds before reconnecting the power chord.
    Try and update the printer's firmware. HP Color LaserJet Pro MFP M177fw.
    Please check your private messages for additional steps to try.
    In the forum beside your handle name just click on the envelope to view it.
    How is the printer connected? (USB/Ethernet/Wireless)
    If you appreciate my efforts, please click the Thumbs up button below.
    Thank You. I look forward to hearing from you.
    Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
    Click the “Kudos Thumbs Up" on the right to say “Thanks” for helping!
    Gemini02
    I work on behalf of HP

  • Hp color laserjet cm6040 mfp unkon non hp black drum

    hp color laserjet cm6040 mfp unkon non hp black drum
    tecnical support for hp printing

    >> ...  Preserver Orientation is also checeked ... I don't know what this means (I don't have access to a LaserJet CM6040, or its drivers, or to Windows Server 2008, so it may be something like a driver setting which I'm not familiar with?). First thing you need to do is to try to establish whether the problem is associated with the printer, or the printer control sequences generated by the printer driver (or perhaps something else). Print a small sample (sanitised data) document which you know exhibits the problem when printed, but select the 'print to file' option in the Print dialogue.Then analyse the content of the resultant .prn file to see just what the printer is being told to do. If you could supply a suitable .prn file, I could analyse it.With the old Enterprise printer forums, you could post file attachments, but now that all printing support has moved to these  Consumer forums, you can't do that (at least, not until you've used the forums enough to become trusted). You can perform some analysis yourself, using the PRN FIle Analyse tool in the PCL Paraphernalia application, available via http://www.pclparaphernalia.eu

  • Unable to UNINSTALL "hp Color LaserJet CM1312 MFP Series" from Windows7 64bit OS on HP-8730w

    i am unable to UNINSTALL the "hp Color LaserJet CM1312 MFP Series" from Windows7 64bit OS installed on HP Notebook 8730w Mobile Workstation.
    If i click the uninstall button using the original printer driver CD, nothing happens; no error messages either.

    This seems to be a commercial product. For the best chance at finding a solution I would suggest posting in the forum for HP Business Support!
    You can find the Commercial Laserjet board here:
    http://h30499.www3.hp.com/t5/Printers-LaserJet/bd-p/bsc-413
    Best of Luck!
    You can say thanks by clicking the Kudos Star in my post. If my post resolves your problem, please mark it as Accepted Solution so others can benefit too.

  • HP Color LaserJet Pro MFP M177 Series Fax sends but won't receive faxes

    I can send faxes using HP Color LaserJet Pro MFP M177 Series Fax but I cannot receive them. I have faxed test pages and the setup is correct. Any suggestions?

    Hello DBrad8,
    Welcome to the HP Forums!
    I understand you're unable to receive a fax using the Laserjet MFP M177. I will do my best to assist you! First, I need to find out what type of added features do you have on your fax line? Please post these information on this thread.
    Do you have an answer machine on this line? If so, how many rings to answer is this set to?
    Do you have an Internet Service on this line?
    Please follow this entire HP document on Cannot Send or Receive Faxes. Run a fax test page and let me know if everything passed or if anything failed. I will be looking forward to hearing from you. Have a great day!
    I worked on behalf of HP.

  • HP Color LaserJet CM2320 MFP Series PCL 6 - Colour Priniting Issue

    Hi, 
    We have a HP Color LaserJet CM2320 MFP Series PCL 6 at work and it has started to print incorrect colours, when printing a document that should come out as grey and red it comes out as green for the grey and yellow for the red. Some of the cartridges are getting low but none have run out so not sure what to do. Can someone please help as we have things we need to print but they are not printing correctly.
    I did try calloing for support hbut after speaking to two sets of people I got put back onto the voice active service whcih just took me around and around in circles and didn;t get me to human being so I gave up.
    Thanks
    Dee

    HI DeePure, 
    Print out the supplies status page, and let me know if all the colors print correctly?
    Do you have an extra set of cartridges we can use to troubleshoot with?
    Print the supplies status page
    Follow these steps to print out the supplies status page from your printer.
    On the Printer’s control panel, press the Setup button.
    Press the down arrow to highlight Reports , and then press OK .
    Press the down arrow  to highlight Supplies Status Page , and then press OK .
    Figure 1: Supplies Status Page
    I am an HP employee.
    Say Thanks by clicking the Kudos Star in the post that helped you.
    Please mark the post that solves your problem as "Accepted Solution"

  • HP Color LaserJet MFP M570dw and HP Web Services

    Hi,
    I have a HP Color LaserJet MFP M570dw printer and have tried to enable the HP Web Services, but without success.
    My printer is configured on a fixed ip-address, with a default gateway and of course with static DNS servers (8.8.8.8 and 8.8.4.4).
    Every time when I try to enable the Web Services feature I get the error message "Connection error. Check your internet connection.".
    My internet connection is working fine and the printer is able to communicate thru the firewall fine too. When I do some tracing I see the printer communicating to the public ip-address "23.21.172.122" but there is no response comming back. So I assume the problem is external and not related to my internal configuration. I have tested this with a fully opened firewall (allowing all communications from my LAN to the Internet) with exactly the same results. There is no answer comming back from the ip "23.21.172.122".
    Also I can't find the HP Color LaserJet MFP M570dw printer in the supported HP ePrint printerlist.
    The 400-series is supported, the 500-serie is not mentioned.
    But since the webinterface of my HP Color LaserJet MFP M570dw printer is giving me the HP Web Services configuration page, I asumed this type would be supported too...
    Does anyone have a clue how to get ePrint working on the HP Color LaserJet MFP M570dw printer?
    Is there anyone who got the HP Web Services working on a HP Color LaserJet MFP M570dw printer?
    Kind regards,
    Rene. 
    This question was solved.
    View Solution.

    Hi Rene,
    Have you tried updating its firmware version?
    The latest firmware should improve the web services connectivity and may help resolving such an issue:
    http://h20565.www2.hp.com/portal/site/hpsc/templat​e.PAGE/public/psi/swdDetails/?sp4ts.oid=5210913&sp​...
    Also be sure to follow its steps which may help resolving a connection issue:
    • Improvements made for connecting to HP Web Services.
    NOTE: After updating from firmware datecode 20121002 to firmware datecode 20121019, if a connection to HP's Web Services cannot be established a Security Reset should be performed. Use the following steps to perform a Security Reset.
    1. At the printer's touch screen control panel press the wrench & gear icon (Setup menu) at the top of the touch screen.
    2. Using the scroll arrows on the right side, scroll until Network Setup appears then press Network Setup.
    3. In the Network Setup menu select Security
    4. Using the scroll arrows on the right side, scroll until Reset All Security appears and then press Reset All Security. Allow the reset to complete before attempting to connect to HP's Web Services.
    Shlomi
    Say thanks by clicking the Kudos thumb up in the post.
    If my post resolve your problem please mark it as an Accepted Solution

Maybe you are looking for