HP(Compaq) mini 110 has lights but won't turn on

My Compaq mini 110 won't power up. The light where the plug attaches is lit. The wite and blue leds on the front are lit. When the power switch is activated, the internal fan bumps but immediately stops. No noises of any kind. Battery is unplugged - just the power cord used. Main system board just replaced and it does the same thing so that is not it unless I got a bad replacement board. The powerboard has 19V at the main 4 pin connector (2 red and 2 black wires). I cannot find a pin out of voltages for the 18 wire connector running to the mainboard. Could the power board be bad but still light all lights? Not sure what to try next.

Hi,
I have the same problem. Started to night... Computer operated normaly and then just gave a bluescreen... Now works for 30min and then shuts off. I dont hear the fan work at all. I cleaned the fan with air and still dont work. How to make sure that the fan works? and how to replace if it dosent work.
- Mika

Similar Messages

  • Compaq Mini 110 won't start after cleaning Think Point virus

    Hi
    I'm helping my daughter with the following problem with her Compaq mini 110.
    After removing the Think Point virus according to advice in different places the mini 110 don't boot after power on. The choice of pressing F10 (BIOS setup) and F9 (boot order) appears. If I don't touch any key at startup it starts accessing the hard disk for a few seconds, according to the hard disk LED and hard disk sound. Then it stops the boot procedure. Somewhere on the HP web site I read that pressing F11 repeatedly during boot would give the opportunity to choose operatings system recovery from the recovery partition. It doesn't respond to F11. Setting boot device priority doesn't seem to be a solution, since there is only one choice, so I can't force it into the recovery. I would appreciate any advice how to proceed. Below I add som additional facts.
    Some threads on the forum mentions pressing F6 for recovery funktions, but it doesn't respond. There also ought to be some function on F12, but I can't figure out what. Doesn't respond anyway. Any explanation for F6 or F12?
    Thanks,
    Per
    FACTS:
    Computer model: Compaq Mini 110c-1100SO
    OS is Windows XP as supplied with the computer and was never changed.
    Hard disc diagnostics in BIOS setup performed without error reports (160 GB, disc type suggests Seagate hard disc)
    RAM diagnostics in BIOS setup performed without error reports (1 GB)
    Pressing F9 at startup gives no choices apart from the hard disk, no choice for partitions or USB boot.
    I have set the delay for the user to press F10 to 5 seconds.
    The display/screen works properly during BIOS setup
    Power adaptor connected, and charging LED lights constantly (as I expect it to do)
    Power on LED lights constantly
    Wireless network LED lights constantly
    Caps lock LED flashes briefly at start up, then gets dark.
    When booting stops, background light on display is on, no text or symbols are shown at this state.
    BIOS password has never been activated
    BIOS Administrator Password has never been activated
    Internal Network Adapter Boot never enabled

    Hi,
    On the link below is a brief guide ( and the download ) to create a bootable Antivirus disk.  Create this disk on another PC and when done, start the infected PC so that you can open the DVD drive, insert the Antivirus CD you've created and then restart the infected PC to initiate the process.
    http://www.techmixer.com/kaspersky-rescue-disk-loa​d-kaspersky-antivirus-2009-using-dos/
    Let me know how you get on.
    Best wishes,
    DP-K
    ****Click the White thumb to say thanks****
    ****Please mark Accept As Solution if it solves your problem****
    ****I don't work for HP****
    Microsoft MVP - Windows Experience

  • My MacBook Pro has a faint blinking orange light on the charger but won't turn on, I've tried many different things to restart it but nothing works

    My MacBook Pro has a faint blinking orange light on the charger but won't turn on, I've tried many different things to restart it but nothing works

    The battery's probably drained and the power brick on the fritz. Unfortunately, if she won't start there's little we can do for software-based diagnosis. You'll have to take it in to a Store or Service Provider for assessment.

  • Compaq mini 110

    compaq mini 110 is saying enter CURRENT password
    the code that comes up is CNU9354VZ1
    please help, thanks

    Hi,
    Try a Hard Reset as follows.
    Shut down the notebook, unplug the AC Adapter and then remove the battery.  Hold  down the Power button for 30 seconds.  Plug in the AC Adapter ( leave the battery out for the moment ).
    Tap away at the esc key as soon as you start the notebook to enter the Start-up Menu, then select f10 to enter the Bios Menu.  Press f5 to load the defaults ( this is sometimes f9, but the menu at the bottom will show the correct key ), use the arrow keys to select 'Yes' and hit enter.  Press f10 to save the setting and again use the arrow keys to select 'Yes' and hit enter.
    Regards,
    DP-K
    ****Click the White thumb to say thanks****
    ****Please mark Accept As Solution if it solves your problem****
    ****I don't work for HP****
    Microsoft MVP - Windows Experience

  • Compaq mini 110 BIOS password help!!

    Hi. Someone please help me. I just inherited a Compaq mini 110 from my grandmother and its asking for a current bios password it gives me this code CNU9423NXW. I tried the code I got from bios-pw.org but it doesn't work. What can I do? Help please!.

    Hi, Firstly they are all lower cases, secondly the third character is a lower case of letter L and thirdly what is your keyboard ? You must use English (US) or English (International) keyboard. Regards.

  • Compaq mini 110 Bios pasword reset

    compaq mini 110    CNU9275YOM   pls master code... Thanks

    Remove the bios battery and the battery waited for 2 days. When I try to reinsert the password again asked me.

  • Compaq mini 110 CNU927BB89 ŞİFRESİNİ BULAMIYORUM

    compaq mini 110 CNU927BB89 ŞİFRESİNİ BULAMIYORUM
    This question was solved.
    View Solution.

    Hi,
    Enter:      e9lo7xppuo       ( 3rd character is a lower case L )
    Regards,
    DP-K
    ****Click the White thumb to say thanks****
    ****Please mark Accept As Solution if it solves your problem****
    ****I don't work for HP****
    Microsoft MVP - Windows Experience

  • My canon 5320 has ink but won't print on mac os 10.7.5

    my canon 5320 has ink but won't print on mac os 10.7.5

    Hi olschoolmike_1,
    To try and resolve the issue, you will want to confirm that the inkjet nozzles are dispensing the ink correctly by printing a nozzle check pattern from the printer.  If the pattern does not print correctly, we recommend performing at least one cleaning and two deep cleanings on the printer to try and get the ink to print..  To print the nozzle check pattern and perform the cleanings, please follow the steps located here.  If you still experience difficulty after performing the cleanings, please call or email us using one of the methods on the Contact Us page for further assistance.
    Did this answer your question? Please click the Accept as Solution button so that others may find the answer as well.

  • Mini ipad has frozen and won't let me restore showng 3014 error code.  I have tried all suggestions to correct error and mini ipad is now frozen saying connect to itunes.  Can't i just reboot it somehow?

    BIG QUESTION!!!!
    My mini ipad has frozen and won't let me restore showing 3014 error code.  I have tried all suggestions to correct error and now is frozen saying connect to itunes which just shows the error message..  Can't i just reboot it somehow?

    Hi annababs,
    This article has troubleshooting specific for error 3014:
    iTunes: Specific update-and-restore error messages and advanced troubleshooting
    http://support.apple.com/kb/ts3694
    Unable to contact the iOS software update server gs.apple.com
    Error 1004, 1013, 1638, 3014, 3194: These errors may be the result of the connection to gs.apple.com being redirected or blocked. Follow these steps to resolve these errors:
    Install the latest version of iTunes.
    Check security software and ensure that communication to gs.apple.com is allowed. Follow these stepsfor assistance with security software.
    Check the hosts file. The restore will fail if there is an active entry to redirect gs.apple.com. Follow theadvanced iTunes Store troubleshooting steps to edit the hosts file or revert to a default hosts file. See "Blocked by configuration: (Mac OS X/Windows) > Rebuild network information."
    Try to restore from another known-good computer and network.
    If the errors persist on another computer, the device may need service.
    If that does not work, this article may be able to help:
    iOS: Unable to update or restore
    http://support.apple.com/kb/ht1808
    Take care,
    - Ari

  • In my ipad mini sound is there but somehow display turned off....please help...how to turn on the display

    In my ipad mini sound is there but somehow display turned off....please help...how to turn on the display

    Frozen or unresponsive iPad
    Resolve these most common issues:
        •    Display remains black or blank
        •    Touch screen not responding
        •    Application unexpectedly closes or freezes
    http://www.apple.com/support/ipad/assistant/ipad/
    iPad Frozen, not responding, how to fix
    http://appletoolbox.com/2012/07/ipad-frozen-not-responding-how-to-fix/
    iPad Frozen? How to Force Quit an App, Reset or Restart Your iPad
    http://ipadacademy.com/2010/11/ipad-frozen-how-to-force-quit-an-app-reset-or-res tart-your-ipad
    Black or Blank Screen on iPad or iPhone
    http://appletoolbox.com/2012/10/black-or-blank-screen-on-ipad-or-iphone/
    What to Do When Your iPad Won't Turn On
    http://ipad.about.com/od/iPad_Troubleshooting/ss/What-To-Do-When-Your-Ipad-Wo-No t-Turn-On.htm
    iOS: Not responding or does not turn on
    http://support.apple.com/kb/TS3281
    Home button not working or unresponsive, fix
    http://appletoolbox.com/2013/04/home-button-not-working-or-unresponsive-fix/
    Fixing an iPad Home Button
    http://tinyurl.com/om6rd6u
    iPad: Basic troubleshooting
    http://support.apple.com/kb/TS3274
     Cheers, Tom

  • TS1741 Remote app on my iOS devices control my apple tv, but won't turn my newest gen apple tv on when i open the app.

    Remote app on my iOS devices control my apple tv, but won't turn my newest gen apple tv on when i open the app. It used to turn my previous gen apple tv on. Remote app controls apple tv just fine once i turn it on with the provided remote control. Help?

    Hello CournteyGould3,
    Congratulations on your new Apple TV!  I found an article with steps you can take when your remote app can't connect to the Apple TV.  I recommend following the steps in the article below (you can skip any steps you have already taken):
    Remote app for iPhone, iPad, or iPod touch can't connect to iTunes or Apple TV
    http://support.apple.com/kb/TS1741
    Thank you for using Apple Support Communities.
    Best,
    Sheila M.

  • My phone keeps displaying a white screen with the apple, then occasionally flicks to a blue screen, but won't turn on! HELP!!

    My phone keeps displaying a white screen with the apple, then occasionally flicks to a blue screen, but won't turn on! HELP!! I have had it on charge all day and have tried plugging it in to my computer to sync.

    Restore your software using iTunes.
    Turn your device off and connect your cable to the computer, but not the device just yet. Start up iTunes. Now, hold down the home button on your device and plug it in to the cable - don't let go of the button until iTunes tells you it's detected a device in recovery mode. Now you can restore to factory settings.
    You should be able to restore your backup file after this procedure. If the problem comes back, you either have corruption in your backup file, or a serious hardware problem that should be looked at by a tech at the Genius Bar (make an appointment first).

  • Compaq Mini 110c-1001NR Sound Drivers won't install

    I am fixing a Compaq Mini 110c-1001NR for a friend. They reinstalled XP on it, so I had to install wireless internet drivers for them. I then realized the sound doesn't work. I downloaded the drivers from HP's website (yes they are the right ones!), but half way through the install, it said it couldn't find any compatible hardware. I don't know what is wrong. That laptop has windows XP on it, so it should be compatible, right?
    Please help asap. Thanks.

    Hi:
    First install the chipset driver and reboot.
    http://h10025.www1.hp.com/ewfrf/wc/softwareDownloadIndex?softwareitem=ob-71064-1&cc=us&dlc=en&lc=en&...=
    Uninstall the audio driver and first install this:
    http://h20000.www2.hp.com/bizsupport/TechSupport/SoftwareDescription.jsp?lang=en&cc=us&prodTypeId=32...
    Then see if the audio driver will install.
    http://h10025.www1.hp.com/ewfrf/wc/softwareDownloadIndex?softwareitem=ob-71197-1&cc=us&dlc=en&lc=en&...=
    Paul

  • Battery indicator lights show full battery but won't turn on

    I have an early 2008 non-unibody MacBook Pro. For about a year now, the status of the battery has been "replace soon." I was still getting a pretty good amount of time off of one charge so I wasn't too worried. This past Saturday morning, I woke up, checked the battery indicator lights on my computer (it had been sleeping since the day before) and it said it had about 60% percent so I opened it. I was on the Internet for about 10 minutes before it shut off without warning. It wouldn't turn back on when I pressed the power button, so I plugged it in and it turned back on. When I checked, the battery status was "replace now." After using it, I turned it back off and left for NYC for the weekend and didn't bring it with me. When I got home last night, I plugged it in and tried turning it on with no luck. The battery indicator light was flashing one light, so I just assumed it would need to charge for a bit before it would turn back on. After about two hours, when I went to bed, it still was flashing just one light. I kept it plugged in over night, and this morning when I checked it, the battery indicator lights showed that it was fully charged, but it still wouldn't turn on. I still kept it plugged in throughout the day just in case, but it still won't turn on even though all the lights are lit. Is the battery just showing me false information, or should I be worried about more than just the battery? Might I have to get a new computer altogether? I bought a replacement battery online so I'll have my answer in a few days, but I was just wondering.

    And for what it's worth, I tried reseating the RAM and resetting the SMC, both with no luck. Could it be the logic board? The only reason I think it might not be is because my computer still worked a little bit after it first shut off, it was only after it was off for an extended period of time that it wouldn't turn back on.

  • Green light but won't discover

    I am having issues connecting my airport extreme. My AE has been working fine. I disconnected and brought it to Alaska. Hooked it up and got green lights, but was unable to connect to the internet. I reset modem and AE no success. Tried using ethernet thru the AE but that didn't work either. Deleted relative passwords in Keychain thinking it may be causing a problem, but that didn't work either. the last time I was here I used an older model airport and didn't have any problems. I am trying to connect via a GCI modem. Box shows IP 169.254.47.96. I am wondering if I should manually put in a 255 address? Any suggestions? I can hook up via ethernet from modem directly to the computer.
    Kenny

    It sounds like the modem still "remembers" the previous device connected to it and is not recognizing the AirPort Extreme Base Station (AEBS).
    Please try the following, in order, checking for Internet access after each step, until resolved:
    1. If the modem has a reset switch, use it to reset the modem. Wait at least 5-10 minutes for the modem to initialize.
    2. Remove power from the modem. If it has a backup battery, remove this as well. Wait 5-10 minutes. Replace the battery, and add power back to the modem.
    3. Perform a complete power recycle of your network components as follows:
    o Power-off the modem, AEBS, & computer(s); Wait at least 10-15 minutes. Note: Order is not critical.
    o Power-on the modem; Wait at least 10-15 minutes.
    o Power-on the AEBS; Wait at least 5-10 minutes.
    o Power-on the computer(s)
    4. Contact your ISP to have them perform a "modem reset."

Maybe you are looking for