HP Data Protector: Backing up deduplicated server

Hello,
I'm using HP Data Protector 6.21, and I'm trying to find out if it's possible to use this to back up a Windows Server 2012 R2 with deduplication enabled. I've seen on other forums that people are able to run the backups successfully, but they still have questions about whether or not the data is valid, or the amount of data backed up doesn't match the used space on the server, etc. Does anyone have any experience with this configuration?
- Scott

Ok I ran a consistency check and it completed successfully with the following message. However after a few minutes of it showing OK it now shows Replica is Inconsistent again.
Type: Consistency check
Status: Completed
Description: The job completed successfully with the following warning:
An unexpected error occurred while the job was running. (ID 104 Details: Cannot create a file when that file already exists (0x800700B7))
More information
End time: 2/3/2015 11:19:38 AM
Start time: 2/3/2015 10:34:35 AM
Time elapsed: 00:45:02
Data transferred: 220.74 MB
Cluster node -
Source details: G:\
Protection group members: 35
Details
Protection group: E*
Items scanned: 2017709
Items fixed: 653
There was a log for a failed synchronization job from yesterday here are the details of that.
Type: Synchronization
Status: Failed
Description: The replica of Volume G:\ on E*.net is not consistent with the protected data source. (ID 91)
More information
End time: 2/2/2015 10:04:01 PM
Start time: 2/2/2015 10:04:01 PM
Time elapsed: 00:00:00
Data transferred: 0 MB
Cluster node -
Source details: G:\
Protection group members: 35
Details
Protection group: E*

Similar Messages

Data Roll back When Java Server Down.

hi
When sending the data to DB using JDBC,the data is not effecting in Data base because of Java Server Down.
Is there any Procedure for Rollback the data.
Thanks in Adavnce

There isn't any rollback functionality in XI.
U can try resending the data from XI.
Regards,
Prateek

HP Data Protector

I would like to know about HP Data Protector which supports Windows Server's backups, Oracle 10g Database backup, Exchange server backups.
If you can help me which distributor can provide me the solution for above requirement in Saudi Arabia
Thanks & Regards,
Syed Imran
[email protected]

HP data protector 7.00 and new 8.00 supports the servers you mentioned.
For more info http://www.autonomy.com/products/data-protector
You can go to this site and contact with them, they will give info about the local resellers in Saudi Arabia.

Data Protection Manager 2012 - Inconsistent when backing up Deduplicated File Server

Protected Server
Server 2012 File Server with Deduplication running on Data drive
DPM Server
Server 2012
Data Protection Manager 2012 Service Pack 1
We just recently upgraded our DPM server from DPM 2010 to DPM 2012 primarily because it is supposed to support Data Deduplication. Our primary File server that holds our home directories etc. is limited on space and was quickly running low so just after
we got DPM 2012 in place we optimized the drive on the file server which compressed the data about 50%. Unfortunately shortly after enabling deduplication the protected shares on the deduplicated volume are getting a Replica is Inconsistent error.
I continually get Replica is Inconsistent for the Server that has deduplication running on it. All of the other protected servers are being protected as they should be. I have run a consistency check multiple times probably about 10 times and it keeps going
back to Replica is inconsistent. The replica volume shows that it is using 3.5 TB and the Actual protect volume is 4TB in size and has about 2.5 TB of data on it with Deduplication enabled.
This is the details of the error
Affected area:   G:\
Occurred since: 1/12/2015 4:55:14 PM
Description:        The replica of Volume G:\ on E****.net is inconsistent with the protected data source. All protection activities for data source will fail until the replica is synchronized with
consistency check. You can recover data from existing recovery points, but new recovery points cannot be created until the replica is consistent.
For SharePoint farm, recovery points will continue getting created with the databases that are consistent. To backup inconsistent databases, run a consistency check on the farm. (ID 3106)
More information
Recommended action:
Synchronize with consistency check.
Run a synchronization job with consistency check...
Resolution:
To dismiss the alert, click below
Inactivate
Steps taken to resolve - I’ve spent some time doing some searches and haven’t found any solutions to what I am seeing. I have the data deduplication role installed on the DPM server which has been the solution for many people seeing similar issues. I have
also removed that role and the added it back. I have also removed the protected server and added it back to the protection group. It synchronizes and says consistent then after a few hours it goes back to inconsistent. When I go to recovery it shows that I
have recovery points and it appears that I can restore but because the data is inconstant I don’t feel I can trust the data in the recovery points. Both the protected server and the DPM servers’ updates are managed via a WSUS server on our network.
You may suggest I just un-optimize the drive on the protected server however after I have optimized the drive it takes a large amount more of space to un-optimize it (Anyone know why that is) anyways the drive isn’t large enough to support un-optimization.
If anyone has any suggestions I would appreciate any help. Thanks in advanced.

Ok I ran a consistency check and it completed successfully with the following message. However after a few minutes of it showing OK it now shows Replica is Inconsistent again.
Type: Consistency check
Status: Completed
Description: The job completed successfully with the following warning:
An unexpected error occurred while the job was running. (ID 104 Details: Cannot create a file when that file already exists (0x800700B7))
More information
End time: 2/3/2015 11:19:38 AM
Start time: 2/3/2015 10:34:35 AM
Time elapsed: 00:45:02
Data transferred: 220.74 MB
Cluster node -
Source details: G:\
Protection group members: 35
Details
Protection group: E*
Items scanned: 2017709
Items fixed: 653
There was a log for a failed synchronization job from yesterday here are the details of that.
Type: Synchronization
Status: Failed
Description: The replica of Volume G:\ on E*.net is not consistent with the protected data source. (ID 91)
More information
End time: 2/2/2015 10:04:01 PM
Start time: 2/2/2015 10:04:01 PM
Time elapsed: 00:00:00
Data transferred: 0 MB
Cluster node -
Source details: G:\
Protection group members: 35
Details
Protection group: E*

There was an error while writing data back to the server: Failed to commit objects to server : Duplicate object name in the same folder.

Post Author: dmface15
CA Forum: Administration
I am working in a new enviorment and i am trying to save a report to the Crystal Server via the CMC. I am uploading the report from the objects tab and attempting to save to a folder. The report has 1 static defined parameter and that's it. When i click submit to save the report i receive the following error message: "There was an error while writing data back to the server: Failed to commit objects to server : Duplicate object name in the same folder." There is not a anothe report within the folder with that name. What could be causing this error message and equally important, what is the solution.

hte message you received about duplicate user probably means something hadn't fully updated yet. Once it did then it worked...
Regards,
Tim

How to get data passed back to server from Web Start client ?

dear experts,
my web application allows users to launch a web start window from the jsp page, after users enters some data in the web start page and press "OK", the data entered should be passed back server for process. i just have not much clue how to do this....
thanks.

Use the java networking library to send a request to a url that takes the arguments you want to pass in.
Example:
URL url = new URL("http://yourserver/yourhandler.do?arg1=foo&arg2=bar");
HttpURLConnection conn = (HttpURLConnection) URL.openConnection(url);
... any output testing, etc...
conn.disconnect();It's not the prettiest, but it ought to get the job done.
You should probably (at least) use the BasicService to get the codebase back to the server that served up the jnlp file.
-Mike

How to send data back to the server

i create a program to send data back to ther server using j2me.
its work well on emulator but when i install the application on sony ericsssin p910i or k700i or nokia 7710 then its not working and simply hang.
here is sample code which is run well on emulator but not on mobile.
what is the problem in that or how can this code run in mobile is there any mobile specific setting or internet setting.
Pls reply asap.
import java.io.*;
import javax.microedition.io.*;
import javax.microedition.lcdui.*;
import javax.microedition.midlet.*;
* An example MIDlet to invoke a CGI script.
public class ThirdExample extends MIDlet {
private Display display;
// String url = "http://www.javacourses.com/cgi-bin/getgrade.cgi?idnum=182016";
String url = "http://sampler.infopro.stpn.soft.net/midletdata.asp?name=name";
public ThirdExample() {
display = Display.getDisplay(this);
* Initialization. Invoked when we activate the MIDlet.
public void startApp() {
try {
getGrade(url);
} catch (IOException e) {
System.out.println("IOException " + e);
e.printStackTrace();
* Pause, discontinue ....
public void pauseApp() {
* Destroy must cleanup everything.
public void destroyApp(boolean unconditional) {
* Retrieve a grade....
void getGrade(String url) throws IOException {
HttpConnection c = null;
InputStream is = null;
OutputStream os = null;
StringBuffer b = new StringBuffer();
TextBox t = null;
int x = 5, y =7;
try {
c = (HttpConnection)Connector.open(url);
c.setRequestMethod(HttpConnection.GET);
c.setRequestProperty("IF-Modified-Since", "10 Nov 2000 17:29:12 GMT");
c.setRequestProperty("User-Agent","Profile/MIDP-1.0 Confirguration/CLDC-1.0");
c.setRequestProperty("Content-Language", "en-CA");
os = c.openOutputStream();
String str = "?idnum=182016";
byte postmsg[] = str.getBytes();
for(int i=0;i<postmsg.length;i++) {
os.writeByte(postmsg);
os.flush();
is = c.openDataInputStream();
int ch;
while ((ch = is.read()) != -1) {
b.append((char) ch);
System.out.println((char)ch);
t = new TextBox("Final Grades", b.toString(), 1024, 0);
} finally {
if(is!= null) {
is.close();
if(os != null) {
os.close();
if(c != null) {
c.close();
display.setCurrent(t);
}>

i create a program to send data back to ther server using j2me.
its work well on emulator but when i install the application on sony ericsssin p910i or k700i or nokia 7710 then its not working and simply hang.
here is sample code which is run well on emulator but not on mobile.
what is the problem in that or how can this code run in mobile is there any mobile specific setting or internet setting.
Pls reply asap.
import java.io.*;
import javax.microedition.io.*;
import javax.microedition.lcdui.*;
import javax.microedition.midlet.*;
* An example MIDlet to invoke a CGI script.
public class ThirdExample extends MIDlet {
private Display display;
// String url = "http://www.javacourses.com/cgi-bin/getgrade.cgi?idnum=182016";
String url = "http://sampler.infopro.stpn.soft.net/midletdata.asp?name=name";
public ThirdExample() {
display = Display.getDisplay(this);
* Initialization. Invoked when we activate the MIDlet.
public void startApp() {
try {
getGrade(url);
} catch (IOException e) {
System.out.println("IOException " + e);
e.printStackTrace();
* Pause, discontinue ....
public void pauseApp() {
* Destroy must cleanup everything.
public void destroyApp(boolean unconditional) {
* Retrieve a grade....
void getGrade(String url) throws IOException {
HttpConnection c = null;
InputStream is = null;
OutputStream os = null;
StringBuffer b = new StringBuffer();
TextBox t = null;
int x = 5, y =7;
try {
c = (HttpConnection)Connector.open(url);
c.setRequestMethod(HttpConnection.GET);
c.setRequestProperty("IF-Modified-Since", "10 Nov 2000 17:29:12 GMT");
c.setRequestProperty("User-Agent","Profile/MIDP-1.0 Confirguration/CLDC-1.0");
c.setRequestProperty("Content-Language", "en-CA");
os = c.openOutputStream();
String str = "?idnum=182016";
byte postmsg[] = str.getBytes();
for(int i=0;i<postmsg.length;i++) {
os.writeByte(postmsg);
os.flush();
is = c.openDataInputStream();
int ch;
while ((ch = is.read()) != -1) {
b.append((char) ch);
System.out.println((char)ch);
t = new TextBox("Final Grades", b.toString(), 1024, 0);
} finally {
if(is!= null) {
is.close();
if(os != null) {
os.close();
if(c != null) {
c.close();
display.setCurrent(t);
}>

Send Data back to the Server

Hi.
how to send data back to the server using J2ME or how to communicate with server using J2ME

i am using http its work well on emulator but when i install the application on sony ericsssin p910i or k700i or nokia 7710 then its not working and simply hang.
here is sample code which is run well on emulator but not on mobile.
what is the problem in that or how can this code run in mobile is there any mobile specific setting or internet setting.
Pls reply asap.
import java.io.*;
import javax.microedition.io.*;
import javax.microedition.lcdui.*;
import javax.microedition.midlet.*;
* An example MIDlet to invoke a CGI script.
public class ThirdExample extends MIDlet {
private Display display;
// String url = "http://www.javacourses.com/cgi-bin/getgrade.cgi?idnum=182016";
String url = "http://sampler.infopro.stpn.soft.net/midletdata.asp?name=name";
public ThirdExample() {
display = Display.getDisplay(this);
* Initialization. Invoked when we activate the MIDlet.
public void startApp() {
     try {
getGrade(url);
     } catch (IOException e) {
     System.out.println("IOException " + e);
     e.printStackTrace();
* Pause, discontinue ....
public void pauseApp() {
* Destroy must cleanup everything.
public void destroyApp(boolean unconditional) {
* Retrieve a grade....
void getGrade(String url) throws IOException {
HttpConnection c = null;
InputStream is = null;
OutputStream os = null;
StringBuffer b = new StringBuffer();
TextBox t = null;
int x = 5, y =7;
try {
c = (HttpConnection)Connector.open(url);
c.setRequestMethod(HttpConnection.GET);
c.setRequestProperty("IF-Modified-Since", "10 Nov 2000 17:29:12 GMT");
c.setRequestProperty("User-Agent","Profile/MIDP-1.0 Confirguration/CLDC-1.0");
c.setRequestProperty("Content-Language", "en-CA");
os = c.openOutputStream();
String str = "?idnum=182016";
byte postmsg[] = str.getBytes();
for(int i=0;i<postmsg.length;i++) {
os.writeByte(postmsg);
os.flush();
is = c.openDataInputStream();
int ch;
while ((ch = is.read()) != -1) {
b.append((char) ch);
System.out.println((char)ch);
t = new TextBox("Final Grades", b.toString(), 1024, 0);
} finally {
if(is!= null) {
is.close();
if(os != null) {
os.close();
if(c != null) {
c.close();
display.setCurrent(t);

Can't Restore Exchange 2010 Mailbox DB from HP Data Protector backup

I'm trying to implement Exchange 2010, but I won't feel comfortable moving many users to it until I've successfully restored a mail database from tape backup. So far, this hasn't worked out so well. I'm using HP Data Protector for my backup solution.
Here's what I've done:
1. In DP's "Restore" GUI, navigated down to the MS Volume Shadow Copy Writers entry, then selected both "Files" and "Logs" from the DB's entry under Microsoft Information Store. I'm not restoring any of the other Writers. So that I don't have to take down Exchange, I'm restoring them to a temporary restore location.
2. After the restore completes, I go to the temporary restore location on the server and run eseutil /mh on the database, which returns a "Dirty Shutdown" db status.
3. Since I have the log files, I attempt to repair using eseutil /r E01 in the log files' path. This generates "Operation terminated with error -1216 (JET_errAttachedDatabaseMismatch, An outstanding database attachment has been detected at the start or end of recovery, but database is missing or does not match attachment info) after 10.608 seconds."
Can anyone suggest what I'm doing wrong with this recovery? If my steps are incorrect I'd love to know, as HP's documentation for restoring Exchange 2010 is very young and not terribly useful. My ultimate goal is to be able to restore a database from DP's tapes and bring it back online on the Exchange 2010 server.
Thanks!
Thanks!

Hi Ben,
We backup our primary database (Ex Writer) and always with full backup (DB+LOGS). When we restore we restore to alternate location, then manualy copy db file and everything from restored log directory to one folder (for example: d:\restore_DB1). At this
stage DB is in dirty shutdown state. Then we run (in folder where we copied db file and log files)
Eseutil.exe /R E00 /D
it takes a couple of seconds (160GB file) and the db is in clean shutdown state. Then we do:
New-MailboxDatabase -Name “Restored DB” -Server MBOX1 -EDBFilePath “D:\Restore_DB1\DB1.edb”
-Logfolderpath “D:\Restore_DB1” -Recovery
and
Mount-Database “Restored DB”
now we can restore single mailbox or even single item from mailbox with:
1: whole mailbox with overite the destination
Restore-Mailbox –Identity “USERNAME” –RecoveryDatabase “Restored DB”
2. whole mailbox to alternate location (new folder in another mailbox)
Restore-Mailbox –Identity “EXISTING MAILBOX TO RESOTRE TO” –RecoveryDatabase “Restored DB” –RecoveryMailbox “MAILBOX DO BE RESTORED
FROM BACKUP” –TargetFolder “NEW FOLDER IN EXISTING MAILBOX”
3. the same as 2 but single item with MEETING in email subject
Restore-Mailbox –Identity “EXISTING MAILBOX TO RESOTRE TO” –RecoveryDatabase “Restored DB” –RecoveryMailbox “MAILBOX DO BE RESTORED
FROM BACKUP” -SubjectKeywords "MEETING" –TargetFolder “NEW FOLDER IN EXISTING MAILBOX”
Best Regards,
Alex

HP Data Protector: Could not gather changed blocks on disk

Running HP Data Protector 7, backing up about 30 VM's, without issue, until recently. Had a HP switch hang on us, while backups were running. Everything was stopped, so we took the time to reboot switch, all servers, including VM, Data Protector server, etc. Physical machine backups run without issue. 5 of the 30 VM's run without issue. The other 25 VM's get this errror: Could not gather changed blocks on disk (scsci disk id). We've tried resetting change block on vm, but that does not help. Have tried both incremental, and full backups. Any ideas?

This is the consumer forum, you need to post on the enterprise forum http://h30499.www3.hp.com/

MaxDB backup problem through Data protector

When I start the Online MaxDB database backup through Data Protector GUI the backup fails with error as below,
Normal] From: BSM@ttcsap10 "MAXDB_Online" Time: 6/17/10 4:30:49 AM
OB2BAR application on "ttcmaxdr" successfully started.
[Normal] From: OB2BAR_SAPDBBAR@ttcmaxdr "MAX" Time: 06/17/10 04:30:50
Executing the dbmcli command: `user_logon'.
[Normal] From: OB2BAR_SAPDBBAR@ttcmaxdr "MAX" Time: 06/17/10 04:30:50
Executing the dbmcli command: `dbm_configset -raw set_variable_1 OB2OPTS=""'.
[Normal] From: OB2BAR_SAPDBBAR@ttcmaxdr "MAX" Time: 06/17/10 04:30:50
Executing the dbmcli command: `dbm_configset -raw set_variable_2 OB2APPNAME=MAX'.
[Normal] From: OB2BAR_SAPDBBAR@ttcmaxdr "MAX" Time: 06/17/10 04:30:50
Executing the dbmcli command: `dbm_configset -raw set_variable_3 OB2BARHOSTNAME=ttcmaxdr'.
[Normal] From: OB2BAR_SAPDBBAR@ttcmaxdr "MAX" Time: 06/17/10 04:30:50
Executing the dbmcli command: `dbm_configset -raw set_variable_4 TimeoutWaitFiles=30'.
[Normal] From: OB2BAR_SAPDBBAR@ttcmaxdr "MAX" Time: 06/17/10 04:30:51
Executing the dbmcli command: `dbm_configset -raw BSI_ENV /var/opt/omni/tmp/MAX.bsi_env'.
[Normal] From: OB2BAR_SAPDBBAR@ttcmaxdr "MAX" Time: 06/17/10 04:30:51
Executing the dbmcli command: `medium_put BACKDP-Data[2]/1 /var/opt/omni/tmp/MAX.BACKDP-Data[2].1 PIPE DATA 0 8'.
[Normal] From: OB2BAR_SAPDBBAR@ttcmaxdr "MAX" Time: 06/17/10 04:30:51
Executing the dbmcli command: `medium_put BACKDP-Data[2]/2 /var/opt/omni/tmp/MAX.BACKDP-Data[2].2 PIPE DATA 0 8'.
[Normal] From: OB2BAR_SAPDBBAR@ttcmaxdr "MAX" Time: 06/17/10 04:30:51
Executing the dbmcli command: `util_connect'.
[Normal] From: OB2BAR_SAPDBBAR@ttcmaxdr "MAX" Time: 06/17/10 04:30:51
Executing the dbmcli command: `backup_start BACKDP-Data[2] DATA'.
[Critical] From: OB2BAR_SAPDBBAR@ttcmaxdr "MAX" Time: 06/17/10 04:31:45
Error: SAPDB responded with:
-24988,ERR_SQL: SQL error
-903,Host file I/O error
3,Data backup failed
17,Servertask Info: because Error in backup task occured
10,Job 2 (Backup / Restore Medium Task) [executing] WaitingT170 Result=3700
6,Error in backup task occured, Error code 3700 "hostfile_error"
1,Backupmedium #1 (/var/opt/omni/tmp/MAX.BACKDP-Data[2].1) Wrong file type
6,Backup error occured, Error code 3700 "hostfile_error"
17,Servertask Info: because Error in backup task occured
10,Job 1 (Backup / Restore Medium Task) [executing] WaitingT170 Result=3700
6,Error in backup task occured, Error code 3700 "hostfile_error"
[Normal] From: OB2BAR_SAPDBBAR@ttcmaxdr "MAX" Time: 06/17/10 04:31:45
Executing the dbmcli command: `exit'.
[Normal] From: BSM@ttcsap10 "MAXDB_Online" Time: 6/17/10 4:31:46 AM
OB2BAR application on "ttcmaxdr" disconnected.
[Critical] From: BSM@ttcsap10 "MAXDB_Online" Time: 6/17/10 4:31:46 AM
None of the Disk Agents completed successfully.
Session has failed.
[Normal] From: BSM@ttcsap10 "MAXDB_Online" Time: 6/17/10 4:31:46 AM
Backup Statistics:
Session Queuing Time (hours) 0.00
Completed Disk Agents ........ 0
Failed Disk Agents ........... 0
Aborted Disk Agents .......... 0
Disk Agents Total ........... 0
========================================
Completed Media Agents ....... 0
Failed Media Agents .......... 0
Aborted Media Agents ......... 0
Media Agents Total .......... 0
========================================
Mbytes Total ................. 0 MB
Used Media Total ............. 0
Disk Agent Errors Total ...... 0
But I have noticed the error is because of this line as below,
Executing the dbmcli command: `medium_put BACKDP-Data[2]/1 /var/opt/omni/tmp/MAX.BACKDP-Data[2].1 PIPE DATA 0 8'.
Actually it should execute the dbmcli command as
medium_put BACKDP-Data[2]/1 /var/opt/omni/tmp/MAX.BACKDP-Data[2].1 PIPE DATA 0 8 NO NO \" \" "BACK"
But I donu2019t know where to make changes so that when I start the backup through DP GUI it should use backup tool as u201CBACKu201D
But same DP backup specification is working through MaxDB Database Manager GUI.
Any solution appreciatedu2026
Thanks,
Subba

Hi Natalia,
Thanks for the reply...Please find the answer as below,
-> What is the version of Data Protector?
Data Protector 5.5
-> What is the version of the database?
SAP MaxDB 7.6
-> According your information you could use the DBMGUI to create the medium of u201CBACKu201D type and create the databackup using this medium. Correct?
Yes
The problems are with Data Protector GUI, not with MAXDB or DBMGUI. Correct?
Yes
Please let me know where to make any changes or any enviornment settings to be done in Data Protector GUI so that it will use the medium "BACK" as backup tool while i start the backup through Data Protector GUI.
Thanks,
Subba

Backup MaxDB 7.6 mit HP Data Protector; Wrong file type

Hallo.
Wir versuchen, eine MaxDB-Datenbank (Rel. 7.6) auf SUSE-LINUX unter Verwendung von HP Data Protector zu sichern. Der Versuch, das Backup durchzuführen, schlägt fehl, da auf dem MaxDB-Server anscheinend die Pipe nicht angelegt werden kann. Folgende Meldung wird ausgegeben:
From: BSM-hph3000.thebis.de "Content_sdb_sdba" Time: 26.04.2008 10:19:16
      OB2BAR application on "dell2950.thebis.de" successfully started.
From: OB2BAR_SAPDBBAR-dell2950.thebis.de "SDB" Time: 04/26/08 10:16:22
      Executing the dbmcli command: `user_logon'.
From: OB2BAR_SAPDBBAR-dell2950.thebis.de "SDB" Time: 04/26/08 10:16:22
      Executing the dbmcli command: `dbm_configset -raw set_variable_1 OB2OPTS="(null)"'.
From: OB2BAR_SAPDBBAR-dell2950.thebis.de "SDB" Time: 04/26/08 10:16:22
      Executing the dbmcli command: `dbm_configset -raw set_variable_2 OB2APPNAME=SDB'.
From: OB2BAR_SAPDBBAR-dell2950.thebis.de "SDB" Time: 04/26/08 10:16:22
      Executing the dbmcli command: `dbm_configset -raw set_variable_3 OB2BARHOSTNAME=dell2950.thebis.de'.
From: OB2BAR_SAPDBBAR-dell2950.thebis.de "SDB" Time: 04/26/08 10:16:22
      Executing the dbmcli command: `dbm_configset -raw set_variable_4 TimeoutWaitFiles=30'.
From: OB2BAR_SAPDBBAR-dell2950.thebis.de "SDB" Time: 04/26/08 10:16:22
      Executing the dbmcli command: `dbm_configset -raw BSI_ENV /usr/omni/tmp/SDB.bsi_env'.
From: OB2BAR_SAPDBBAR-dell2950.thebis.de "SDB" Time: 04/26/08 10:16:22
      Executing the dbmcli command: `medium_put BACKDP-Data[1]/1 /usr/omni/tmp/SDB.BACKDP-Data[1].1 PIPE DATA 0 8'.
From: OB2BAR_SAPDBBAR-dell2950.thebis.de "SDB" Time: 04/26/08 10:16:22
      Executing the dbmcli command: `util_connect'.
From: OB2BAR_SAPDBBAR-dell2950.thebis.de "SDB" Time: 04/26/08 10:16:22
      Executing the dbmcli command: `backup_start BACKDP-Data[1] DATA'.
From: OB2BAR_SAPDBBAR-dell2950.thebis.de "SDB" Time: 04/26/08 10:16:23
      Error: SAPDB responded with:
      -24988,ERR_SQL: SQL error
      -903,Host file I/O error
      3,Data backup failed
      1,Backupmedium #1 (/usr/omni/tmp/SDB.BACKDP-Data[1].1) Wrong file type
      6,Backup error occured, Errorcode 3700 "hostfile_error"
      17,Servertask Info: because Error in backup task occured
      10,Job 1 (Backup / Restore Medium Task) WaitingT131 Result=3700
      6,Error in backup task occured, Errorcode 3700 "hostfile_error"
From: OB2BAR_SAPDBBAR-dell2950.thebis.de "SDB" Time: 04/26/08 10:16:23
      Executing the dbmcli command: `exit'.
From: BSM-hph3000.thebis.de "Content_sdb_sdba" Time: 26.04.2008 10:19:18
      OB2BAR application on "dell2950.thebis.de" disconnected.
From: BSM-hph3000.thebis.de "Content_sdb_sdba" Time: 26.04.2008 10:19:18
      None of the Disk Agents completed successfully.
      Session has failed.
Ein Versuch, die Pipe /usr/omni/tmp/SDB.BACKDP-Data[1].1 manuell auf dem MaxDB-Server anzulegen, schlug ebenso fehl. Eine Pipe /usr/omni/tmp/SDB.BACKDP-Data kann angelegt werden.
Frage 1) Hat jemand ein ähnliches Problem und dazu eine Lösung?
Frage 2) Wo ist hinterlegt, welchen Medium-Name der Data Protector beim command "medium_put" verwenden soll?
Danke für Eure Hilfe!
Gruß
Gerhard Krauß
Heidelberg

Hi Marcus,
we use the version 5.5.
The pipe name is generated by the Data Protector. When I want to create manually a pipe with this name I got the message "No hit found".
Do you know a possibilty where we can configure (at Data Protector or MaxDB) which medium name should be used for creating the pipe?
Thanks a lot!
Gerhard

Backup with Data Protector is not working

Hello,
[US]We have an Oracle DB which is saved by HP Data Protector
[FR]Nous avons une BDD Oracle qui est sauvegardée via HP DataProtector.
[US]During our last backup, the Data Protector Server has crashed which has stopped the backup during the process.
[FR]Lors de la dernière sauvegarde, le serveur de backup a planté, arrêtant de ce fait la sauvegarde en cours de la BDD Oracle.
[US]Now, when we are trying to relaunch the backup, it doesn't work at all.
The Data Protector agent is starting, it sends the RMAN command to the DB and then stop.
[FR]Maintenant, lorsque nous voulons relancer la sauvegarde, elle ne fonctionne plus.
L'agent démarre bien, il envoie bien la commande à RMAN qui démarre puis s'arrête.
[US] Of we launch the backup manually thru RMAN, it works
[FR]Lorsqu'on lance cette même sauvegarde manuellement via RMAN, elle fonctionne !
[US]Lors are not really explicit !
[FR]Les logs ne sont pas très parlant:
LOGS of DATA PROTECTOR (in french but I've translated (in bold) which I think, is important)
Citation:
[Normal] De : [email protected] "Base10G_DBName_1_Archivelogs_rman_delete" Heure : 26/02/2013 12:10:31
La session de sauvegarde 2013/02/26-31 a démarré.
[Normal] De : [email protected] "Base10G_DBName_1_Archivelogs_rman_delete" Heure : 26/02/2013 12:10:33
Lancement de l'application OB2BAR sur "clientxxx.domain.com" réalisé avec succès.
[Normal] De : [email protected] "DBNameq" Heure : 26/02/2013 12:10:34
D?marrage de la sauvegarde de la base de donn?es cible.
Nom du service r?seau : DBNameq.
Etat de l'instance : OPEN.
Nom d'instance : DBNameq.
DBID de la base de donn?es = 3864252955.
Type de fichier de contr?le de BDD : CURRENT.
Mode journalisation BDD : ARCHIVELOG.
Logging mode: ARCHIVELOG.
[Normal] De : [email protected] "DBNameq" Heure : 26/02/2013 12:10:35
D?marrage de Oracle Recovery Manager.
Recovery Manager: Release 10.2.0.4.0 - Production on Mar. F?vr. 26 12:10:35 2013
Copyright (c) 1982, 2007, Oracle. All rights reserved.
RMAN> CONNECT TARGET *
2> CONNECT CATALOG *
3> HOST 'exit';
4> run {
5> allocate channel 'dev_0' type 'sbt_tape'
6> parms 'SBT_LIBRARY=C:/PROGRA~1/OmniBack/bin/orasbt.dll,ENV=(OB2BARTYPE=Oracle8,OB2APPNAME=DBNameq,OB2BARLIST=Base10G_DBName_1_Archivelogs_rman_delete)'
7> ;
8> allocate channel 'dev_1' type 'sbt_tape'
9> parms 'SBT_LIBRARY=C:/PROGRA~1/OmniBack/bin/orasbt.dll,ENV=(OB2BARTYPE=Oracle8,OB2APPNAME=DBNameq,OB2BARLIST=Base10G_DBName_1_Archivelogs_rman_delete)'
10> ;
11> allocate channel 'dev_2' type 'sbt_tape'
12> parms 'SBT_LIBRARY=C:/PROGRA~1/OmniBack/bin/orasbt.dll,ENV=(OB2BARTYPE=Oracle8,OB2APPNAME=DBNameq,OB2BARLIST=Base10G_DBName_1_Archivelogs_rman_delete)'
13> ;
14> allocate channel 'dev_3' type 'sbt_tape'
15> parms 'SBT_LIBRARY=C:/PROGRA~1/OmniBack/bin/orasbt.dll,ENV=(OB2BARTYPE=Oracle8,OB2APPNAME=DBNameq,OB2BARLIST=Base10G_DBName_1_Archivelogs_rman_delete)'
16> ;
17> allocate channel 'dev_4' type 'sbt_tape'
18> parms 'SBT_LIBRARY=C:/PROGRA~1/OmniBack/bin/orasbt.dll,ENV=(OB2BARTYPE=Oracle8,OB2APPNAME=DBNameq,OB2BARLIST=Base10G_DBName_1_Archivelogs_rman_delete)'
19> ;
20> allocate channel 'dev_5' type 'sbt_tape'
21> parms 'SBT_LIBRARY=C:/PROGRA~1/OmniBack/bin/orasbt.dll,ENV=(OB2BARTYPE=Oracle8,OB2APPNAME=DBNameq,OB2BARLIST=Base10G_DBName_1_Archivelogs_rman_delete)'
22> ;
23>
24> send device type 'sbt_tape' 'OB2BARHOSTNAME=clientxxx.domain.com';
25> sql 'alter system archive log current';
26> backup
27> format 'Base10G_DBName_1_Archivelogs_rman_delete<DBNameq_%s:%t:%p>.dbf'
28> archivelog all
29> delete input;
30> backup
31> format 'Base10G_DBName_1_Archivelogs_rman_delete<DBNameq_%s:%t:%p>.dbf'
32> current controlfile;
33> }
34> EXIT
RMAN-06005: connect? ? la base de donn?es cible : DBNameQ (DBID=3864252955)
RMAN-06005: connected to targeted database : DBNameQ (DBID=3864252955)
RMAN-06008: connect? ? la base de donn?es du catalogue de r?cup?ration
RMAN-06008: connected to recovery database
RMAN-08030: canal affect? : dev_0
RMAN-08030: allocated chanel : dev_0
RMAN-08500: canal dev_0 : sid=422 typedev=SBT_TAPE
RMAN-08500: dev_0 channel : sid=422 typedev=SBT_TAPE
RMAN-08526: canal dev_0 : Data Protector A.06.20/DPWIN_00536(b621)
RMAN-08526: dev_0 channel : Data Protector A.06.20/DPWIN_00536(b621)
RMAN-08030: canal affect? : dev_1
RMAN-08500: canal dev_1 : sid=888 typedev=SBT_TAPE
RMAN-08526: canal dev_1 : Data Protector A.06.20/DPWIN_00536(b621)
RMAN-08500: canal dev_2 : sid=681 typedev=SBT_TAPE
RMAN-08526: canal dev_2 : Data Protector A.06.20/DPWIN_00536(b621)
RMAN-08030: canal affect? : dev_3
RMAN-08500: canal dev_3 : sid=717 typedev=SBT_TAPE
RMAN-08526: canal dev_3 : Data Protector A.06.20/DPWIN_00536(b621)
RMAN-08030: canal affect? : dev_4
RMAN-08500: canal dev_4 : sid=223 typedev=SBT_TAPE
RMAN-08526: canal dev_4 : Data Protector A.06.20/DPWIN_00536(b621)
RMAN-08030: canal affect? : dev_5
RMAN-08500: canal dev_5 : sid=212 typedev=SBT_TAPE
RMAN-08526: canal dev_5 : Data Protector A.06.20/DPWIN_00536(b621)
RMAN-06421: commande envoy?e au canal : dev_0
RMAN-06421: command send to channel : dev_0
RMAN-06421: commande envoy?e au canal : dev_1
RMAN-06421: commande envoy?e au canal : dev_2
RMAN-06421: commande envoy?e au canal : dev_3
RMAN-06421: commande envoy?e au canal : dev_4
RMAN-06421: commande envoy?e au canal : dev_5
RMAN-06162: instruction SQL : alter system archive log current
RMAN-06162: SQL query : alter system archive log current
RMAN-03090: D?marrage de backup dans 26/02/13
RMAN-03090: BAckup is starting in 26/02/13
RMAN-08031: canal lib?r? : dev_0
RMAN-08031: released channel : dev_0
RMAN-08031: canal lib?r? : dev_1
RMAN-08031: canal lib?r? : dev_2
RMAN-08031: canal lib?r? : dev_3
RMAN-08031: canal lib?r? : dev_4
RMAN-08031: canal lib?r? : dev_5
[Normal] De : [email protected] "Base10G_DBName_1_Archivelogs_rman_delete" Heure : 26/02/2013 12:10:46
Application OB2BAR sur "clientxxx.domain.com" déconnectée.
Application OB2BAR on"xxx" disconnected.
[Critique] De : [email protected] "Base10G_DBName_1_Archivelogs_rman_delete" Heure : 26/02/2013 12:10:46
Aucun Agent de disque ne s'est effectué correctement.
La session a échoué.
None of the Disk Agents completed successfully.
Session has failed.
[Normal] De : [email protected] "Base10G_DBName_1_Archivelogs_rman_delete" Heure : 26/02/2013 12:10:46
Statistiques de la sauvegarde :
Temps de file d'attente de la session (en heures) 0,00
Agents de disque terminés ........ 0
Agents de disque ayant échoué ........... 0
Agents de disque abandonnés .......... 0
Total des Agents de disque ........... 0
========================================
Agents de support terminés ....... 0
Agents de support ayant échoué .......... 0
Abandon des Agents de support ......... 0
Total des Agents de support .......... 0
===========================================
Total Méga-octets ................. 0 Mo
Total des supports utilisés ............. 0
Total d'erreurs d'Agent de disque ...... 0

Hello,
No disconnection at all.
It doesn't work since a crash of the DP server during the DB backup.
When we move the catalog on the same server as the DB, the backup works but if we set the catalog to an other server (like the original setting) it doesn't work and we don't know why.
It seems that when a backup is launched thru Data Protector, RMAN can't find the DB catalog. But if we run (manually) the RMAN command that DP used to do a backup, it works...

Trying to change server to be a PDC; reverts back to Standalone Server

I'm trying to get my Leopard server to run as a PDC for windows authentication, but when I change the role from "Standalone Server" to "Primary Domain Controller" and click the save button, after authenticating with the "diradmin" account the changed settings all revert back to "Standalone Server" and nothing gets changed. Any clues as to what I need to do? The server is fully updated to 10.5.3, with all other software updates as well.

Hi Topher
I'm guessing you're referring to the post? Well the figure has gone up a fair bit since then. My overall total is quite high as I have been installing servers since 10.2.
FWIW my general rule of thumb is:
1 Format drive, install server
2 On Restart Server Assistant launches (see linked post) don't start any services using Server Assistant
3 Server Assistant does start VNC and enables SSH and the Root Account
Depending on your view SSH and Root are potentially a security problem, deal with these later on.
4 Server Assistant writes settings and preps the server for first use
5 Don't launch WGM or Server Admin. If Server Admin launches, quit it
6 Manually download the latest OS update, don't use Software Update
7 Install this and on successful restart run Software Update again and install the rest of the updates
8 Make sure server is fully up to date before launching Server Admin
9 User server's .local name to log in initially
10 Enable and Configure DNS Service first
I can't stress this enough but if you devote time and energy on this before doing anything else it can prevent a lot of hassle and problems later on. DNS does not have to be running on the Server itself. If you have another server for example you can configure DNS Services on that. You could even use 3rd-Party DNS Software and install on a client machine for example. An old Graphite G4 with DNS Enabler installed is good enough. There are PC equivalents you could use as well. This approach does not require anything in terms of processing power, large drives or even vast amounts of RAM. Reliability and correct configuration is the key.
11 Test and Qualify the DNS Service before moving onto anything else.
Once you are happy enable AFP and SMB. Create a test user in the local node and see if you can access the default share points from a client. Try it with both protocols. Don't be tempted to delete the default share points either. You'll have serious problems if you do.
12 Enable the Open Directory Service
13 Promote to Open Directory Master
If DNS is perfect the Kerberos Realm and search base fields should autofill themselves with information based on the domain name defined in the DNS Service. For example an FQDN of myserver.mydomain.com would result in MYSERVER.MYDOMAIN.COM for the Kerberos Realm and dc=myserver,dc=mydomain,dc=com for the Search Base. I always use the default diradmin name rather than any other. You should not use the local administrator account name
Launch Directory Utility and verify the loopback address (127.0.0.1) is entered as a new configuration. Access Server Admin's File Sharing window and enable the Users folder to automount for home directories. Quit out of Server Admin and launch WorkGroup Manager
Try and get into the habit of only having one or other of the Server Applications open at any one time on the server itself. Its OK to have both open if you are administering the Server remotely if you install them on a client
Authenticate to the /LDAPv3/127.0.0.1 node and you should see Directory Administrator UID 1000 already waiting for you. Create a user and select Advanced. You should see the afp url for the default Users folder. Click create home now and Save. Navigate to the Users folder and you should see a home folder created for that user, inspect the contents of this folder and you should see the usual home folder folders. Quit out of WorkGroup Manager
Launch Server Admin select SMB and go for promotion. Supply diradmin as the user name and its password and you should have the server acting as a Primary Domain Controller
Everything can be achieved using the GUI. There should be no need to resort to the command line although if you want to - as you well know - you can
As for your question? No I have not seen any problems with the 10.5.3 update. The 10.5.2 update has given me a problem on a handful of occasions. The problem was traced - eventually - to failing hard drives.
I apologize for the long post but who knows you might find it useful?
Tony

Fetch data from another mirosoft sql server to sap

Dear all,
I want to fetch data from another mirosoft sql server
to SAP(my sap server IN unix, oracle 10g).
Thanks
Shashi
Moderator Message: Try to do you own research before posting your question. Get back to the forums in case you are stuck with any issue
Edited by: Suhas Saha on Jul 26, 2011 3:21 PM

hi,
u should see following documentation:
Oracle9i Heterogeneous Connectivity Administrator's Guide
Release 1 (9.0.1)
Part Number A88789_01
in it u just go to chapter no. 4 (using the gateway),,u'll find ur answer there.
regards
umar

HP Data Protector: Backing up deduplicated server

Similar Messages

Maybe you are looking for