HP Deskjet 3512 - Can't enable ePrint

Hi,
We just bought the printer over the weekend. Set it up yesterday. We have no problems printing through USB or wireless. The ePrint can't be enabled by the Setup Assistant or on the printer itself.
Message kept popping out saying that proxy address is needed to connect but we do not use or have any proxy to connect to the internet.
Device OS: Mac 10.8.3
Printer software: Deskjet 3510 series v12.2.23 (12.23)
We appreciate any help. Thank you in advance.

Let's set a static IP address and external DNS for the printer:
- Print a Network Config Page from the front of the printer. Note the printer's IP address.
- Type that IP address into a browser to reveal the printer's internal settings.
- Choose the Networking tab, then Wireless along the left side, then the IPv4 tab.
- On this screen you want to set a Manual IP. You need to set an IP address outside the range that the router automatically sets (called the DHCP range). If you do not know the range, change the last set of numbers (those after the last '.') to 250
- Use 255.255.255.0 for the subnet (unless you know it is different, if so, use that)
- Enter your router's IP (on the Network Config Page) for the gateway.
- Enter 8.8.8.8 for the first DNS and 8.8.4.4 for the second DNS. This is Google DNS. You can choose another external DNS if you wish.
- Click 'Apply'.
Now, shut down the router and printer, start the router, wait, then start the printer.
After this you may need to redo 'Add a Printer' using the new IP address.
Say thanks by clicking "Kudos" "thumbs up" in the post that helped you.
I am employed by HP

Similar Messages

Can't enable eprint

I finally got my HP P1102w hooked up, and it seems to be working (at least on first attempt) with AirPrint, but, when I log in through the internet using the IP address, and try to enable eprint, it says "Connection Error. Check Internet Connection." I've tried unloading and reloading/re-config on wireless, but to no avail. When I print the self test, I don't see anything that resembles an email address.
What am I doing wrong?

On my OJ Pro 8600 it requires you to enable web services on the printer, then you'll get a printer code that you use at the eprintcenter.com site to enable eprinting. Did you set up an account on eprintcenter.com?
mikehd

Can't enable eprint even with network connected

Windows 8 computer network is connected but eprint won't enable HP8600. Have followed directions for pushing refresh button. Still disabled.

Try the steps below. Make sure nothing is entering under proxy address.
1. Open an internet browser type printer's IP address.
2. Should bring you to the printer's status page.
3. Select network tab at the top.
4. Left hand side select IPv4 under wireless.
5. Under DNS address Configuration select Manual DNS Server.
6. For Preferred enter 8.8.8.8
7. For Alternate enter 8.8.4.4
8. Select apply. You might get a warning saying this could interrupt connection that's fine.
9. Turn printer off for about 30 seconds then try again.
Let me know it goes.

Can't enable web services/eprint

For some reason my Hp6700 will not allow me to enable web services/e-print

dcousine,
The first thing I would try in this situation is a network reboot.
First, disconnect the power cord from the back of your router.
Next disconnect the power cord from either the back of the printer or the wall, without powering it off first.
Wait about 30 seconds and reconnect the power cord to your router.
Wait about another 30 seconds and plug the printer back in. It should boot back up automatically, but if it doesn't go ahead and press the power button.
Once everything is back up and running, try to enable ePrint.
If that doesn't work for you, let me know and I can give you some more steps to try.
-------------How do I give Kudos? | How do I mark a post as Solved? --------------------------------------------------------

Lost my HP deskjet 3512 printer function when upgrading to Windows 8.1 - can't get it back!

I lost my wireless connection from my Hp A6 Vision lapptop to my HP 3512 deskjet printer when I upgraded to Windows 8.1. I'm told it is installed but it is not responding. I'v tried following instructions and even using the Hp wizard to get it up and running. Is it even compatible with 8.1? What do I need to do?

Hi @periwinklejoy,
Welcome to the HP Forums!
I understand that you lost your wireless connection to your HP Deskjet 3512 after upgrading to Windows 8.1. I am happy to help!
The printer is definitely compatible with Windows 8.1. As there are drivers available at this website, HP Deskjet 3510 e-All-in-One Printer Full Feature Software and Drivers.
I would recommend the following:
Uninstall the software. Uninstalling the Printer Software. (In case there are old drivers still installed, if not then carry on to the next step).
Clean boot the computer. How to perform a clean boot in Windows.
Re-install using the HP Printer Install Wizard for Windows.
Then follow this guide, Installing the Printer Software for a Wireless Network Connection.
Hope this helps you, and thank you for posting!
RnRMusicMan
I work on behalf of HP
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos Thumbs Up" to say “Thanks” for helping!

Print problem with HP Deskjet 3512

I have an error when I try to eprint on my HP Deskjet 3512 I tried to print, and it didn't print...my computer said I had an error. No error showing on my printer. Now when I try to print, I get a message saying that it has to print the previous print job first, only it never does. Now I can't print anything and I have this error showing

Hi,
Try running the tool below by selecting Fix Printing:
http://h10025.www1.hp.com/ewfrf/wc/softwareDownloadIndex?softwareitem=mp-126353-1&cc=us&dlc=en&lc=en...
Follow the steps on screen to troubleshoot the problem.
Please let me know if that helps,
Shlomi
Say thanks by clicking the Kudos thumb up in the post.
If my post resolve your problem please mark it as an Accepted Solution

How do I connect my ipad to hp deskjet 3512

I have a hp deskjet 3512 wireless printer an scanner an copier I can't get it to connect with my wifi on my ipad I need to know what's going on or how to get it set up. I have work to do an need my deskjet set up to scan print an copy ASAP

iOS AirPrint Printers http://support.apple.com/kb/HT4356http://support.apple.com/kb/HT4356
How to Print from Your iPad: Summary of Printer and Printing Options
http://ipadacademy.com/2012/03/how-to-print-from-your-ipad-summary-of-printer-an d-printing-optionshttp://ipadacademy.com/2012/03/how-to-print-from-your-ipad-summary-of-printer-an d-printing-options
How to Print from Your iPad
http://www.dummies.com/how-to/content/how-to-print-from-your-ipad.htmlhttp://www.dummies.com/how-to/content/how-to-print-from-your-ipad.html
How do you print directly from the iPad
http://www.everymac.com/systems/apple/ipad/ipad-faq/how-to-print-documents-direc tly-from-ipad.htmlhttp://www.everymac.com/systems/apple/ipad/ipad-faq/how-to-print-documents-direc tly-from-ipad.html
Print from iPad / iPhone without AirPrint
http://ipadhelp.com/ipad-help/print-from-ipad-iphone-without-airprint/http://ipadhelp.com/ipad-help/print-from-ipad-iphone-without-airprint/
How to Enable AirPrint on a Mac and Use Any Printer
http://ipadhelp.com/ipad-help/how-to-use-airprint-with-any-printer/http://ipadhelp.com/ipad-help/how-to-use-airprint-with-any-printer/
iPad Power: How to Print
http://www.macworld.com/article/1160312/ipad_printing.htmlhttp://www.macworld.com/article/1160312/ipad_printing.html
Check out these print apps for the iPad.
Print Utility for iPad ($3.99) http://itunes.apple.com/us/app/print-utility-for-ipad/id422858586?mt=8http://itunes.apple.com/us/app/print-utility-for-ipad/id422858586?mt=8
Print Agent Pro for iPad ($5.99) http://itunes.apple.com/us/app/print-agent-pro-for-ipad/id421782942?mt=8http://itunes.apple.com/us/app/print-agent-pro-for-ipad/id421782942?mt=8 Print Agent Pro can print to many non-AirPrint and non-wireless printers on your network, even if they are only connected to a Mac or PC via USB.
FingerPrint turns any printer into an AirPrint printer
http://reviews.cnet.com/8301-19512_7-57368414-233/fingerprint-turns-any-printer- into-an-airprint-printer/http://reviews.cnet.com/8301-19512_7-57368414-233/fingerprint-turns-any-printer- into-an-airprint-printer/
Print (Print to ALL Printers) ($1.99)
https://itunes.apple.com/us/app/print-print-to-all-printers/id299423224?mt=8https://itunes.apple.com/us/app/print-print-to-all-printers/id299423224?mt=8
 Cheers, Tom

Cannot enable ePrint/Web Services, HP LaserJet CP1525nw

I am trying to follow HP's instructions for enabling ePrint and Web Services for my LaserJet CP1525nw. I printed the Config Report, got the printer's IP address and entered it into a brower as instructed. It does pull up summary page, but there is no "HP Web Services" tab as indicated in all of the HP instructions I can find - only four tabs that read: Status, System, Print, Networking.
I have looked at all sub-menus under each of these tabs, and cannot find anything that even resembles a "Web Services" option.
Can somebody please help? Or is there another way to find the printer's email address so that I can register and use ePrint for my iPhone and iPad?
From what I have been able to find on HP Support, the Airprint software driver(s) are not yet availble for this LaserJet model - or are they?

There is firmware to enable AirPrint in the HP LaserJet CP1525nw.
Go to the support page for this printer:
http://h10025.www1.hp.com/ewfrf/wc/softwareCategory?os=219&lc=en&cc=us&dlc=en&sw_lang=&product=40529...
and pick the type of desktop computer you are using. On the resulting page you will see a choice to download a firmware updated that you can run on your computer to update your printer.

Deskjet 3512 connected to wireless network but utility says 'Unable to find printer'

1. Product Name and Number
     • HP Deskjet 3512
2. Operating System installed (if applicable)
     • Windows 7 64-bit
3. Error message (if any)
     Unable to find printer.
    Facts:
- Printer is connected to network. Panel LED is unblinking blue and the status indicates the correct SSID for my network. Also the router config page indicates that the printer is connected with a correct IP (192.168.1.XX).
- Wireless Network Test Results diagnostics of the printer states that all PASSED, except that the Internet says 'Not connected'.
- Tried to ping the IP that the printer panel says, but cmd says: Destination Host Unreachable. Tried arp -a after that but it does not show the IP & MAC address of the printer.
- Turned off: Windows firewall, router firewall (Telus Actiontec V1000H) and disabled MAC Address Control and uninstalled Avast AV and reboot.
- Cannot access printer Embedded Web Server.
- Tried the HP Print and Scan Doctor and it didnt find the printer. And when it did find it, it was by using the USB cable. After selecting the fixes, it came to 'Unable to Find Printer again'.
4. Any changes made to your system before the issue occurred
     • No changes. Bought the printer and I'm having this issue.
PLEASE HELP!

To start out sounds like this is a driver issue. I want to start with being sure that the removal of the software and reinstallation happened in the best possible fashion. I want you to follow my steps so I can be sure that we are both starting on the same page.
First if you use a USB cord, make sure to remove it (this is important). Do not plug it back in until the software directs you to. Then go through the Devices and Printers, Programs and Features and Device Manager folders and insure that all copies, files, and programs related to the printer are removed. Then as directed, restart the computer.
In the START menu type "%temp%" and press ENTER. Here I want you to press Ctrl+A and hit DELETE. Some of the files will not allow you to delete them, skip those files and delete the majority that allows it.
find and install the FULL FEATURE SOFTWARE if it is available :
http://h10025.www1.hp.com/ewfrf/wc/softwareCategory?cc=us&lc=en&dlc=en&product=5241114
Install that and let me know the result!
Have a great day!
-Spencer

All music gone, transferred to 'other', can't enable disk use on iTunes

it seems like there are a lot of people with similar problems but nothing exact..here goes:
-doing research on my macbook and i get a popup from itunes saying that my ipod was disconnected improperly (i didn't touch it and i wasn't even messing around on itunes)
-ipod restarts and reconnects with itunes and i get another pop up saying that "itunes cannot read the contents of the ipod. go to ipod summery and preferences and restore.
-i would just restore it and reload all the music butttttt like an idiot..i dont keep my music in my itunes cause it takes up way too much space and i never used any external hard drive or anything to back my music up (again..idiot..i know)
-so i read though a ton of forums and posts and see that im not the only one that this has happened to and everyone is saying to put it in disc mode, go to removable disk, copy all the music back to my macbook, restore my ipod, and put all the music back on. i also read something about clicking on my ipod icon on my desktop and going under ipod controls and changing some names (i dont konw if that was jsut for windows or what) but i also dont have an option of ipod controls
-the problem with that is that i can put my ipod into disk mode but that does me no good because i can't enable disk use on itunes because literally..my only option when i plug in my ipod is to restore it. under devices on the left hand menu, it just says ipod..not ipod with a bunch of sub categories like music and playlists and stuff..just ipod.
-normally..i would just give up and restore it but when i go to the about section on my actual ipod, it says that i have 50GB of "other" so that means that stuff is definitely still on it.
-so finally..my main question is:
is there ANY way to enable disk use on my iTunes without doing it through my iPod?..like i explained..when i plug my iPod in..that is not an option. and also..would i benefit from just bringing my laptop and ipod into an apple store and asking for help there or will that just be a waste of time?

The library on the iPod will have been damaged - hence the reason it appears empty, but the media files are still there taking up space and reported as "Other". Check out this post from Zevoneer for some iPod recovery options.
http://discussions.apple.com/thread.jspa?messageID=6273675&#6273675
Some of the tools mentioned will require a working library, but I know from experience that you can use the manual recovey method when the library is missing or damaged. If you're struggling for space you probably need to go & buy an external drive before you start. Stick the iPod in disk mode. Hold Menu+Select > 6 seconds (resets iPod) followed immediately by hold Previous & Select > 6 seconds. You can now drag the contents of iPod_Control\Music to your new hard drive. You may need to reveal hidden files & folders. Once they are on your hard drive you can create a new empty library on the drive, then import the files you have reovered and consolidate the imported library so that the files are in a standard artist\album\## track structure rather that the iPod's obscured names.
tt2

How can I enable embedded pl/sql gateway to run on port 80

I have a new 11G install on OEL 4.0, database created. I would like to be
able to access the instance using the pl/sql gateway. Works fine with
port 8080, the default. How to I enable it to run on port 80?
I found this statement in the following docuementation:
http://download.oracle.com/docs/cd/B19306_01/appdev.102/b14259/xdb22pro.htm#ADXDB2500
Using HTTP(S) on Nonstandard Ports
By default, HTTP listens on a nonstandard, unprotected port: 8080. To use HTTP(S) on
the standard port, such as 80, your DBA must chown the TNS listener to setuid ROOT
rather than setuid ORACLE, and configure the port number in the Oracle XML DB
configuration file /xdbconfig.xml.I have root priviledges on the box.
I've tried setting the listener file permissions:
chown root:dba /u01/app/oracle/product/11.1.0/db_1/bin/tnslsnr
chmod 6775 /u01/app/oracle/product/11.1.0/db_1/bin/tnslsnr
Also put root in the dba group.
The permissions turn out like this:
-rwsr-sr-x 1 root dba 830854 Jun 17 21:04 /u01/app/oracle/product/11.1.0/db_1/bin/tnslsnr
I stopped the listener, bounced the database, and started the listener again.
But it still shows the process being owned by oracle:
oracle 29682 1 0 21:08 ? 00:00:00 /u01/app/oracle/product/11.1.0/db_1/bin/tnslsnr LISTENER -inherit
Changing the port is easy:
Connected to:
Oracle Database 11g Enterprise Edition Release 11.1.0.6.0 - Production
With the Partitioning, OLAP, Data Mining and Real Application Testing options
SYS>select dbms_xdb.gethttpport as "HTTP-Port" , dbms_xdb.getftpport as "FTP-Port" from dual;
HTTP-Port FTP-Port
8080 2100
At this point, I can access the apex home page with the following url:
http://hostname:8080/apex/f?p=4550:10:1454849288245548
I can than change it to port 80:
SYS>begin
dbms_xdb.sethttpport('80');
dbms_xdb.setftpport('2100');
end;
2 3 4 5
PL/SQL procedure successfully completed.
SYS>SYS>select dbms_xdb.gethttpport as "HTTP-Port" , dbms_xdb.getftpport as "FTP-Port" from dual;
HTTP-Port FTP-Port
80 2100
When I try to access apex with the following url:
http://rmdcopslnx1.us.oracle.com/apex/f?p=4550:10:1454849288245548
I get the following:
Failed to Connect
Firefox can't establish a connection to the server at hostname.com.
Though the site seems valid, the browser was unable to establish a connection.
* Could the site be temporarily unavailable? Try again later.
* Are you unable to browse other sites? Check the computer's network connection.
* Is your computer or network protected by a firewall or proxy? Incorrect settings
* can interfere with Web browsing.I can set the port. Just can't talk to it.
This is the entry from the listener log:
<msg time='2008-07-03T15:40:09.741-06:00' org_id='oracle' comp_id='tnslsnr'
type='UNKNOWN' level='16' host_id='hostname'
host_addr='xxx.xxx.xxx.xxx'>
<txt>TNS-12546: TNS:permission denied
TNS-12560: TNS:protocol adapter error
TNS-00516: Permission denied
Linux Error: 13: Permission denied
</txt>
</msg>
So this looks like an permissions problem. But where? I posted
this on the apex forum here:
Re: How can I enable embedded pl/sql gateway to run on port 80
They suggested asking here.

No, that thread did not provide the information that I need. Some more data:
I have the port set to 8080:
Connected to:
Oracle Database 11g Enterprise Edition Release 11.1.0.6.0 - Production
With the Partitioning, OLAP, Data Mining and Real Application Testing options
SYS>select dbms_xdb.gethttpport as "HTTP-Port" , dbms_xdb.getftpport as "FTP-Port" from dual;
HTTP-Port FTP-Port
8080 2100
At this point, I can access the apex home page with the following url:
http://hostname:8080/apex/f?p=4550:10:1454849288245548
I can than change it to port 80:
SYS>begin
dbms_xdb.sethttpport('80');
dbms_xdb.setftpport('2100');
end;
2 3 4 5
PL/SQL procedure successfully completed.
SYS>SYS>select dbms_xdb.gethttpport as "HTTP-Port" , dbms_xdb.getftpport as "FTP-Port" from dual;
HTTP-Port FTP-Port
80 2100
When I try to access apex with the following url:
http://rmdcopslnx1.us.oracle.com/apex/f?p=4550:10:1454849288245548
I get the following:
Failed to Connect
Firefox can't establish a connection to the server at hostname.com.
Though the site seems valid, the browser was unable to establish a connection.
* Could the site be temporarily unavailable? Try again later.
* Are you unable to browse other sites? Check the computer's network connection.
* Is your computer or network protected by a firewall or proxy? Incorrect settings can interfere with Web browsing.
I can set the port. Just can't talk to it.

TS3280 How can i enable both paired bluetooth and ios keyboard input at the same time?

How can i enable both paired bluetooth and ios keyboard input at the same time?
This is needed for the app im working on. Need some user input via keypad as well as scanner input via a paired bluetooth scanner.

You probably should not be using a keyboard bluetooth profile for a scanner, I am not a developer for apple so do not know the location for you to find out the correct profile you should be using for an input device that is not a keyboard. Sorry,
I am sure if you navigate the apple developer site you will probaly finmd what you're looking for.
https://developer.apple.com

Can I enable the root user account from the log in screen when I am locked out of the machine?

Hello everyone,
I am working on my friends mac to get it ready to sell. I went into the advanced options of the user and changed the name of the account. That's all I changed. I did read the warning that said if anything was changed it could cause damage, that's why I only changed the name of the user account. I didn't want to mess with anything else. Well, needless to say, I am locked out of the machine. Apparently the root user, system administrator, account was not enabled and I am stuck at the screen that I can get to with my installation disc. So how can I enable the root user account and get back onto the machine from the screen I am at? Can I enable the root user from terminal? I spent a good 8 hours yesterday researching this topic and have come up empty. Changing passwords from commands in terminal is not the problem. I am given just one account to choose from to log on and it's not accepting the password because of the changes I made in the advanced options menu.
Is there any hope of getting this thing going again? Or have I just screwed myself over?
Thanks for your help!
Leah

You can reset the password.
http://pondini.org/OSX/Password.html
Do you need to recover data from it before you sell it? If not you can just wipe the disk and prepare it for sale.
See > Apple What to do before selling or giving away your Mac
http://support.apple.com/kb/HT5189?viewlocale=en_US&locale=en_US
Also See Thomas Reed's How to Prepare your Mac for sale
http://www.thesafemac.com/how-to-prepare-your-mac-for-sale/
and this thread
https://discussions.apple.com/thread/5474062?tstart=0

I have just installed a 2TB time capsule on my iMac i7, it see my second 1TB hard drive but the 256 SSD doesn't come up in the list of hard drives I can back up. How can I enable the time machine to see my first SSD 256gb hard drive?

I have just installed a 2TB time capsule on my iMac i7, it see my second 1TB hard drive but the 256 SSD doesn't come up in the list of hard drives I can back up. How can I enable the time machine to see my first SSD 256gb hard drive?

iLife is preinstalled on all the Macs. If you purchased iLife in the App Store or your computer came without DVDs, open App Store > Purchases and download the applications. If your Mac came with discs, insert the Applications DVD and install iLife applications

How can I enable SuperFetch?

Hi,
I downloaded Java from Java.com (free download) to be able to open a file I received as email attachment. After the download something happened to my laptop pc (Windows 7). I received pop up messages that said something like "Your computer got infected
you need to install Windows Defender 2015. And they started to pop up almost every second and also the screen view changed. It got upside down or windows messages moved and seemed to be multiplied, very unusual things kept going...
I stopped it and went online on my tablet pc and looked for what to do if my computer got infected with virus (because that's what I thought happened). From what I read online I made sure that all Microsoft windows experts were all recommending to start
my pc in safe mode and I found some instructions such as going to Task Manager and ending processes and also to clear some files and folders in Registry Editor. I wasn't able to clear files and folder in Registry Editor. To make short, I came to the conclusion
that I needed live help from a Microsoft expert. I chatted online with some MS Support Desk techs and followed their instructions but it didn't help at all. When I click on the little flag icon with a red cross sign on it(the one that says Open Action Center)
it says 1 important message-Turn on Windows Security Center service(Important) I tried to turn it on (I don't know how many times!) but I get the message "The Windows Security Center can't be started"
I went to Troubleshooting and clicked on Check of Performance issues (under System and Security) it did checking and I got the message "Problems Found- SuperFetch is not running. Not Fixed.
My question is: HOW CAN I GET SuperFetch running? or How can I enable SuperFetch?
Thank you.
Elif YILDIRIM

Hi Temur, ok. I do the above procedure and it worked fine
Now, I have other question?
How can I reproduce any file (for example: a video, an url page, an image), that is in the flash of DMP?
Índice de ftp://172.17.15.22/tmp/ftproot/tmp/ftproot/tmp/ftproot/usb_1/
Subir al directorio superior.
Nombre Tamaño Última modificación
Sample Videos.lnk
1 KB
17/06/2011
06:25:00 a.m.
deployment
29/06/2010
04:14:00 a.m.
lost+found
25/02/2010
12:00:00 a.m.
video futbol en la playa.mp4
1390 KB
29/06/2010
01:08:00 a.m.
videofutbol.mp4
1390 KB
29/06/2010
01:38:00 a.m.
I like, that el DMP when loss conectivity with DMM, It display at the LCD screen, the video named videofutbol.mp4, this video As I show in the picture above, already in the flash of DMP.
I appreciate your early response.
Thanks

HP Deskjet 3512 - Can't enable ePrint

Similar Messages

Maybe you are looking for