HP Docking (VB041AA) - Using DVI and Display Port at the same time

Hello,
is it supported to use the DV and the Display Port of a HP 90W Docking (VB041AA) at the same time? I use this setup with two LA2405wg and a 6450b for a couple of weeks and I encounter a couple of problems:
- flickering and switching during bootup, same output on both displays, no output
- hibernation resume fails, if notebook was hibernated undocked (hiberfil.sys corrupt)
- sometimes Win7 crashs during startup with corrupt drivers
- spooky display lockups were a display goes into standby and can't be switchec on or off. I have to pull the power cord
Some of them are really strange (corrupt drivers, but after a restart the notebooks starts without problems). During operation I don't have any problems, no BSoDs etc. 
Thanks for advice.

Your notebook is an Enterprise/Business model. I would recommend posting this in the HP Enterprise Support Forums for better coverage, as this is the consumer support forums.
You can access the enterprise support forums at the following link.
http://goo.gl/LsnuK
-------------How do I give Kudos? | How do I mark a post as Solved? --------------------------------------------------------

Similar Messages

  • Can I connect hdmi and display port at the same time?

    The toslink on my 2010 mini is glitchy. So I want to run the audio through the hdmi to my recevier. And the video through the minidisplay port to hdmi to a monitor. Will this work? Can I use the hdmi for audio only and the display port for video only? Thanks

    Yes, that is exactly how to use dual monitors.
    Optionally:
    if the second monitor has DVI input, use the MiniDisplay Port to DVI adapter.
    or if it has Display Port input, then all you need is a straight MiniDisplay Port to Display Port cable.
    In Quick Links try Account if Sign In does not work.

  • G41TM-E43 - DVI and HDMI output at the same time?

    I am looking to output to 2x 1920x1200 displays...nothing 3D and nothing that needs to be decoded...just some power point presentatinos and some flash within a browser window.
    I am pretty sure the resolution isn't going to be a problem, but using both the DVI and HDMI ports at the same time is something I am concerned about.  I am looking for people with actual knowledge that this works...no guessing please.
    Regards,
    Dan

    Quote
    I am looking for people with actual knowledge that this works...no guessing please.
    The likelihood is that you won't be able to use DVI & HDMI at the same time, but you could use one or the other in conjunction with the VGA (D-Sub) port.
    But as this is a user-to-user forum, and you may have to wait for someone with actual experience of this to see this thread and respond, for a definitive answer, contact MSI Support direct:
    http://support.msi.com
    But please do post back with the answer, as this could be useful for others in the future with the same question.

  • Is there a way to connect my MacPro (with DVI and Display ports) to the new Thunderbolt display?

    I'd like to connect these devices together.

    As Kevin J. Doyle points out, the displays from NEC are better than what Apple has to offer for graphics. For video, you'll need a broadcast capable monitor for accurate color correction. Not a computer monitor.
    The 24" model is under $1,000 and it include color calibration items. It has both DVI and Display Port connections. The base can be raised/lowered as well as tilted. (the Apple display does not)
    http://www.bhphotovideo.com/c/product/822739-REG/NEC_P241W_BK_SV_24_Widescreen_P rofessional_Graphics.html
    They have other sizes and resoltuions as well.
    Here's a review on the NEC displays.
    http://macperformanceguide.com/RecommendedDisplays.html

  • Write to serial port and digital port at the same time

    hello,
    I need to write to the digital port and the serial port at the same time. Right now I have the two vi's (to write to the serial port, write to the digital port) in the sequence structure. First I write the digital port, then write the serial port. Using the oscilloscope, the interval between these two executions is 10 ms; and I need to reduce this interval to as small as possible. I would appreciate help in any way. Thank you.

    Hello;
    This is a little tricky. Since the transition from one sequence to another is completely Software timed, and windows manages all tasks that are running at one given time, there isn't a method to reduce that transition time.
    The most you can do is try to optimize your code so all the time expent on the transition is due only to the task management.
    Hope this helps.
    Filipe A.
    Applications Engineer
    National Instruments

  • How can collect the data from laptop sound card and serial port at the same time?

    I'm working on a project, I need to collect the data from laptop sound card, and also from serial port at the same time.
    The attachments are my VIs for sound card and serial port communication, I'm wondering that can I combine these two VIs together? Or can I run these two VI at the same time?
    Thank you!
    Attachments:
    AC_Radar_Receive.vi ‏46 KB
    RadarAudioPlug.vi ‏774 KB

    A smarter way is just to put all your code in the same VI.
    Two parallel loops if rates are different.
    Attachments:
    RadarAudioPlug.vi ‏450 KB

  • MOVED: Re: G41TM-E43 - DVI and HDMI output at the same time?

    This topic has been moved to Intel Core-iX boards.
    https://forum-en.msi.com/index.php?topic=144229.0

    Quote
    I am looking for people with actual knowledge that this works...no guessing please.
    The likelihood is that you won't be able to use DVI & HDMI at the same time, but you could use one or the other in conjunction with the VGA (D-Sub) port.
    But as this is a user-to-user forum, and you may have to wait for someone with actual experience of this to see this thread and respond, for a definitive answer, contact MSI Support direct:
    http://support.msi.com
    But please do post back with the answer, as this could be useful for others in the future with the same question.

  • Win 8 - How to use StereoMix and Headphones Mic at the same time?

    I am using Windows 8 64 bit and believe I may have an IDT driver problem.
    I need to enable StereoMix and my Headphones Mic at the same time. I know this was previously possible with windows xp and windows 7.
    What happens is If I enable either Headphones Mic (Logitech headphones with Mic) or StereoMix the other one becomes " current;ly unavailable"  I cannot get them both to work together. I can get StereoMix and the Internal Mic to work together ( both enabled at the same time) but the sound quality is bad because the internal mic picks up noises from the PC. I need to have both my headphones mic and stereo mix enabled at the same time.
    The driver I'm using is the one provided by HP with the laptop. It is called sp59620.exe
    Would another IDT driver solve the problem? Can you think of another reason this is not working?
    Here are my specs.
    System Manufacturer/Model Number HP Pavillion G7-2251dx
    OS Windows 8 64 bit
    CPU AMD A-8 4500M
    Memory 8 Gigabytes DDR3 sdram
    Graphics Card Discrete ATI Radeon HD 7640G with 2 Gigs
    Sound Card IDT Audio
    Monitor(s) Displays 17.3
    Screen Resolution 1600x900
    If you cannot help, where else should I look? i have tried Windows and Microsoft forums and no one can give me an answer.
    Thank you.

    I have tried the instructions in that video and I cant get passed the very bad feedback i get when telling my recording device to Listen.  His secone instruction from his notes here
    ["Right Click the Realtech HD audio device and set as default if its not already.
    (note you may want to turn off any powered speakers you may have to prevent feedback.)
    -Select the Recording Tab at the top of the window.
    -Select the Stereo Mix device and set it to default if its not already.
    -Right click and select Properties.
    -Select the Listen Tab at the top of the window.
    -Change the drop-down box to the entry for USB headset and check the Listen to this device checkbox.
    -click ok to dismiss the window.
    -Right click on the USB headset microphone device and select properties.
    -Select the Listen Tab at the top of the window.
    -Change the drop-down box to the entry for the Realtech HD Audio device and check the Listen to this device checkbox.
    -click ok to dismiss the window.
    So, essentially, the game audio will play through the Realtec, your mic is also set to play to the Realtec. both audio streams are now part of Stereo Mix. Stereo Mix is being listened to by your headset allowing you to hear the game and your voice.]
    ~~~~~~~~~~~~~~~~~
    Don't know about turning off any powered speakers.. the only speakers I have besides the headphones are the internal laptop speakers.  I get the same feedback if i have the headphones plugged in or not.

  • Airport express: use internet and air tunes at the same time?

    Hi,
    I'd like to use and airport express to create a wirelss network (and so use the internet) AND stream music to my stereo with air tunes - at the same time. Is this possible? So far, I have been able to create a wireless network (and use the internet) OR use the airport express to play music. But whenever my internet works, itune can't find the base station - claiming it "can't be found on the network?"
    Can you do both at once?
    I'm connecting to an ethernet jack (I'm at a college). It's not a cable modem or DSL. Is this the problem?
    Under "music" in the utility configuration. I've selected "Enable Air tunes at the base station." I can't select "Enable Airtunes over ethernet port." When i try to change the network options to allow me to select this "ethernet port" option, I have to tell it how to "distribute IP" addresses. i don't know how to do this, and everything I've tried destroys my internet connection.
    I appreciat any help you have to offer. thanks
    1.5 GHz PowerPC G4, 12'' powerbook   Mac OS X (10.4.4)  

    solution:
    My problem ended up being specific to the network I'm using. There is evidently another router on the ethernet system that was assigning my airport express an IP address (192. ...), rather than letting the network DCHP give me a direct IP address (something like 160. ...). The 192 address made it impossible for iTunes to see my express base station, but I was getting internet, passed through this other router.
    The fix - and I'm not sure if this is totally kosher - was to manually enter a correct IP address for my base station. I got the IP address by seeing what this other router was sending my computer to get onto the internet. It gave me the correct router and a workable (160. ...) IP address. I'm not sure if I'm supposed to manually pick an IP address on the ethernet, but this one is working for the time being, and now iTunes can find my base station.

  • [SOLVED] How to use timidity++ and other programs at the same time?

    I have installed timidity following arch wiki instructions - I have soundfont, and I start it in /etc/rc.conf
    It works properly with tuxguitar (and tuxguitar-alsa) or kmid, but I cannot play MIDI and - for example - oggs in amarok at the same time.
    I suspect that the problem is that timidity doesn't use dmix alsa plugin I have made in my ~/.asoundrc.
    The question is: how to tell timidity to use my dmix plugin?
    Last edited by senjin (2007-11-19 19:53:50)

    but they don't define "default" there, but "!default"...
    anyway, I have already both "default" and "!default" defined exactly the same way:
    pcm.!default
    type plug
    slave.pcm "dmixer"
    pcm.default
    type plug
    slave.pcm "dmixer"
    pcm.dmixer
    type dmix
    ipc_key 1024
    slave
    pcm "hw:0,0"
    format "S32_LE"
    channels 2
    period_time 0
    period_size 1024
    buffer_size 4096
    rate 44100
    bindings
    0 0
    1 1
    ctl.dmixer
    type hw
    card 0
    pcm.w_y_h
    type hw
    card 0
    device 0
    pcm.what_you_hear
    type plug
    ttable.0.10 1 # digital mix left
    ttable.1.11 1 # digital mix right
    slave.pcm w_y_h
    pcm.skype
    type asym
    playback.pcm "dmixer"
    capture.pcm "skype_input"
    pcm.skype_input
    type dsnoop
    ipc_key 2048
    slave
    pcm "hw:0,0"
    period_time 0
    buffer_time 0
    period_size 1024
    buffer_size 8192
    rate 44100
    and it doesn't work!
    Last edited by senjin (2007-11-18 17:49:21)

  • USING TOMTOM AND IPOD FUNCTION AT THE SAME TIME

    Hi
    I plan to het tomtom application bur before I'd like to know if
    I will be able to use my iphone connected to my car player alpine for music fucntions at the same time as tomtom application
    thanks a lo for your opinion on that

    On my iPhone, I can play music using the iPod app and also use Tom Tom. The music pauses for voice directions.
    I don't have an Alpine, so I can't test that for you.

  • Can I Use HDMI and Thunderbolt Outputs At The Same Time? And Mac App Store Issues

    I have a Mid-2011 Mac Mini. I am currently using the HDMI output with an HDMI to Digital Input for a dell monitor. If I wanted to have a second monitor, can I use the Thunderbolt output with a MiniDisplayport to VGA adapter? I know it may sound a little unclear, so if you need a clarification, pelase let me know.
    Also, on the same macine, I am having trouble connecting to the Mac App Store. My internet connection is working, and I've tried going into the Keychain Access and there isn't anything with a blue plus. When I go to Store --> Sign In , the sign in widnow doesn't appear.
    Thanks
    Joey

    Yes, that is exactly how to use dual monitors.
    Optionally:
    if the second monitor has DVI input, use the MiniDisplay Port to DVI adapter.
    or if it has Display Port input, then all you need is a straight MiniDisplay Port to Display Port cable.
    In Quick Links try Account if Sign In does not work.

  • Re: H57M-GD65 - DVI and HDMI output at the same time?

    Hi..,
         apollos here.  I also am preparing my m.b.  retired my 2.5 yr old abit fatal1ty f190HD matx  m.b to try this (MSI H57M-ED65 w\i5 661) My plan is port out all three 'display port, 'hdmi' and sub 15.
    (L.V room hdmi projector, kitchen display port monitor, bedroom vga.)  hdmi no change to L.V., vga to bedroom same.
    ? distances only concern is 'display port' signal....it's about 20ft. Any confirmations?
    thnx,
    apollos 

    Thnx moderator henry (for the sep)
                                                           1. I didn't really 'get' the 'iX' syntx for  the topic .....so any 'i' series socket....yeah makes sense  .....maybe put a couple '' for denotation. and a space bar. 
    2. re: hjking....wasn't intentional ....just typed....'h57m' in the 'search' box.  the ' G41TM-E43' only one that came up; so I ran with it.
    this is more appropriate though.
    m-xmas; h-nyr!!!

  • Using frame and channel API at the same time.

    One of our customers specified the channel-mode number except programming the serial. So I have to use the channel api and the frame api at the the time! Is it possible with a 2 port PXI card like PXI-8461/2 (Port1 for channel api and port 2 for frame api)?

    Yes, you can have one port for channel api and one port for frame api. But you cannot mix on one port.
    DirkW

  • Can I use "g" and "n" AXs at the same time for Airtunes?

    Hi, hope someone can help with this.
    I currently have a wireless "g" network made up of a Netgear DG834PN router handling DHCP and with wireless off, an AEBS "n" as a wirelss base station and 4 AXs (2 "g" and 2"n") doing extended wireless and airtunes to different rooms around the house.
    If I use the Netgear for the "g" wifi and the AEBS for an "n" network and then set up the two "g" AXs on the "g" network and the two "n" AXs on the "n" network, but all still plugged into remote speakers will all the AXs still appear in my iTunes remote speaker list?
    Also, will I still be able to control them all from the Remote app on my 1st gen iPod touch connected to the "g" network?
    I seem to have built a bit of a monster here but it works fine as is. I'd just like to know if I can get a seperate "n" network going without losing any of my airtunes functionality.
    Thanks

    If I use the Netgear for the "g" wifi and the AEBS for an "n" network and then set up the two "g" AXs on the "g" network and the two "n" AXs on the "n" network, but all still plugged into remote speakers will all the AXs still appear in my iTunes remote speaker list?
    Yes, just like any network resource they should be available.
    Also, will I still be able to control them all from the Remote app on my 1st gen iPod touch connected to the "g" network?
    The app on your iPod controls iTunes on your computer streaming the music, so yes you would be able to control them all because you are controlling iTunes.

Maybe you are looking for